Search Documents

By J. E. Breen, J. Weertman

The creep rate of polycrystalline tin was studied as a function of temperature and stress in constant stress experiments. The temperature was varied from room temperature to almost the melting point of tin. Activation energies were calculated from tests run at the same stress. It was found that on a log creep rate vs inverse temperature plot the experimental points did not fall on one straight line but on a line which changed its slope in the 90° to 160°C region. Two activation energies for the creep of tin can be calculated from the data: a value around 26,000 cal per mol at high temperatures and a value around 11,000 cal per mot at low temperatures. It is suggested that the discrepancies between the creep activation energies and those of self-diffusion can be accounted for if self-diffusion takes place predominately by Zener's ring mechanism rather than through vacancy or interstitial movement. SHERBY, Orr, and Dorn' and Dorn' have recently reviewed some of the data on high temperature creep of metals. -The data show that the activation energy of high temperature creep is approximately equal to the activation energy of self-diffusion. This same correlation has also been successfully made between the activation energy of grain boundary relaxation and that of self-diffusion.3,4 The metal tin does not fit into this simple picture. Its activation energies of self-diffusion differ appreciably from that of grain boundary relaxation and of creep. Fensham,5 from a precisely performed experiment, has determined that the activation energies of self-diffusion of tin are 10,500 and 5,900 cal per mol along the C and A axes, respectively. There are two energies because of the anisotropic nature of tin. Rotherham, Smith, and Greenough6 have shown that the grain boundary relaxation activation energy is 19,000 cal per mol (measurements made from room temperature to 100°C). Puttick and King7 found the same activation energy for grain boundary slip in bicrystals of tin (180° to 225°C region). Until recently, there was no high temperature large strain creep data on tin suitable for activation energy calculations. At rather small strains (up to 0.01), Tyte8 had made a series of measurements on tin from which activation energies can be calculated. In Fig. 1 are plotted some of his data on a log creep rate vs inverse temperature graph. It can be seen that Tyte's work indicates that at a relatively low temperature the activation energy is around 7,400 cal per mol but at higher temperatures the activation energy increases. Since Tyte measured the creep only for small strains, it is doubtful if a

Jan 1, 1956

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall's statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall's statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By J. V. Gluck

In the present paper," as in earlier publications, V1'2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge's method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel'~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term 'probable error' was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that 'it is neither an error nor probable' ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people's minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the 'probable error' which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~' of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

Prospectors were digging silver in the Ray mine area in 1873, and by 1880 high-grade copper ore was feeding a 30-ton copper furnace. In 1910, D. C. Jackling and his associates organized the Ray Consolidated Copper Company, known in mining circles as Ray Con, to exploit the Ray orebody. For 50 years, all mining was underground and the Ray mine was known the world over for innovations in mining methods. It was the first to mine important tonnage (8,000 tpd) by block caving methods. The mill at Hayden, 26 miles (41.6 km) from the mine, kept pace with the new mining methods developed at Ray and in the early 1920's flotation replaced gravity concentration by the vanner machines. First mining by open pit methods began in 1950 and in January 1955 all underground mining was discontinued. The new primary crushing plant, installed in early 1967, featured design simplicity with a low capital cost. The 54 in. gyratory crusher was installed within a total height of 6 1 ft (18.65 m) from the truck dump road bed to the floor beneath the feeder-conveyor under the surge pocket. The crusher is fed by 120-ton trucks dumping from one side only into a 200-ton hopper equipped with a horizontal splitter bar to protect the crusher spider. The crushed ore pocket, of 120 -ton live capacity underneath the crusher, discharges to a 0 to 200 fpm (61.2 mpm), variable-speed, 72 in. by 80 ft long (1.83 m by 24.4 m) sloped belt feeder, probably a first in the industry. Wood-picking stations are provided on either side of the belt so that old mine timbers and tramp iron can be removed from the crushed ore and the wood can be dropped into Dempster containers located below the belt. Counter-weighted finger gates control the bed depth on the belt at 14 in. (356 mm) and a low- level radiation unit automatically maintains a minimum of a 3 ft bed (900 mm) of material on the belt directly under the surge pocket. The conveyor is skirted for its full length and is approximately 60 in. (1.52 m) wide inside its metal skirt liners. Ten impact idlers at 12 in. (305 mm) spacing are provided under the loading pocket and remaining idlers are spaced at 18 in. (457 mm). The belt is 1 ¼ in. (31. 8 mm) thick; and, while it has occasionally been damaged by tramp material, belt life averages 11 million tons. When the belt is changed, the coiled new belt is lowered into position onto one of two belt stands mounted over the feeder, the old belt is cut, and one end is attached temporarily to the new belt. The other end of

Jan 1, 1978

By C. S. Barrett, D. F. Clifton

THE transformation that occurs in lithium and its solid solutions containing magnesium1,2 is similar in many respects to other diffusionless transformations of the martensitic type. This general similarity makes it desirable to investigate the transformation curves in detail. The current interest in the phenomenon of stabilization in martensitic transformations has created a need for a careful appraisal of possible stabilization effects in both cooling and heating transformations in lithium alloys. The effect of prior heat treatment on the temperature at which transformation begins and the effect of various temperature cycles in partially transformed alloys also merit attention. Limited data on some of these features were presented previously,' but the present studies have been made with improved apparatus, in which erratic fluctuations were smaller than in the earlier work, and include many independent determinations of certain critical observations. Material and Methods Geiger counter X-ray spectrometers were used: a Norelco instrument, original model, and a General Electric XRD-3. The low-temperature specimen holder has been described elsewhere." Specimens 10 mm in diam and 1.5 mm thick were held in firm contact with a copper block which was attached to the lower end of a stainless steel tube that extended up to a reservoir of liquid nitrogen. A heating coil on the tube permitted a controlled temperature gradient along the tube, so that desired temperatures and rates of heating and cooling could be obtained by controlling the heating current. The specimen was surrounded by an atmosphere of evaporated nitrogen in an insulated chamber having double cellophane windows. The temperature of the specimen was read by a thermocouple imbedded in it close to the irradiated area; the specimen could be held at constant temperature within 1°C for long periods. The body-centered cubic 200 reflection near 8 = 26" was used as the index of the amount of b.c.c. material present; occasional checks were made using the most suitable line of the low-temperature phase, the close-packed hexagonal 110 line near 8 = 29". Copper radiation was used throughout. A continuous record was made of the reflected intensities on a strip chart recorder, both when the peak intensity of a line was being followed and when the lines were being scanned at constant temperature. On the continuous recordings of peak intensity, periodic checks were made on the background intensity between the lines, and on the setting of the spectrometer for maximum intensity. The lithium-base solid solution containing 12.4 atomic pct Mg (33.3 wt pct) that had been used previously' was chosen, as it had a transformation range at relatively high temperatures, so as to permit wide temperature cycling within the range. Just prior to use a pellet was cut from the ingot,

Jan 1, 1951

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

By J. G. Giddings, R. Kobayashi

Residual viscosity, the ViSCOSitY at a given pressure and temperature minus the dilute gas viscosity at the same temperature, has been found to be independent of temperature for pure components and mixtures for simple molecules and light hydrocarbons. The residual viscosities for methane, ethane, propane and four mixtures were correlated as a function of reduced density and molecular weight. INTRODUCTION Earlier efforts in correlating the viscosity of light hydrocarbons and associated gases under pressure, primarily by some form of the corresponding states principle, have been reported elsewhere.7 The formal theory of corresponding states principle for viscosity from non-equilibrium statistical mechanical arguments for simple molecules has been developed by Helfand and Rice.13 The most serious obstacle to the development of a generalized corresponding states representation of viscosity data, even for simple molecules, has been the limited quantity of precise viscosity data of pure components and mixtures over a wide range of pressure and temperature conditions. Viscosity data on light hydrocarbons have recently been contributed by several laboratories.2,6,8,23,25,26 In the study of the viscosity of nitrogen, Michels and Gibson" observed that the viscosities of nitrogen as a function of density gave parallel isotherms. The same behavior has since been reported for other gases.".= The observed behavior indicates that the residual viscosity or the viscosity at a given pressure and temperature minus the dilute gas viscosity at the same temperature is a unique function of the density. Abas-Zade,1 Michels and Botzen,18 and Michels, Bot-Zen, Friedman and Sengers,19 observed similar behavior for thermal conductivity, the residual thermal conductivity being defined in a manner parallel to that of residual viscosity. Thodos and co-workers 4,15,24 applied the residual viscosity concept to the viscosity of pure monatomic and diatomic gases. Ellington and co-workers10,25 made the residual viscosity vs density plots for ethane and propane, but omitted the region below a residual viscosity of 15 micropoise and showed a systematic separation of the ethane isotherms in the low density region. Eakin correlated the residual viscosity of methane, ethane, propane and n-butane empirically as a function of density and molecular weight: Carmichael and Sage6 recently presented ethane residual viscosity vs density values in the gaseous liquid, and near critical regions as a single univariant function of density. Flynn, Hanks, Lemaire and ROSS" have contributed extremely accurate viscosity data to confirm that the residual viscosity concept is essentially correct, but may not be accurate within 0.1 per cent of the viscosity value for the gaseous state- The recent studies by Giddings12 indicate that the residual viscosity of methane, propane and each of four methane-propane mixtures are unique functions of density Over the temperature and the density ranges studied.

Jan 1, 1965

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By L. B. Herring, Harold Decker

The area under discussion includes districts 2 and 4, so designated by the Texas Railroad Commission,‡ and comprises the following 26 counties: Bee, Brooks, Calhoun, Cameron, De Witt, Duval, Goliad, Gonzales, Hidalgo, Jackson, Jim Hogg, Jim Wells, Karnes, Kenedy, Kleburg, Lavaca, Live Oak, Nueces, Refu-gio, San Patricia, Starr, Victoria, Webb, Willacy, Wilson and Zapata. Drilling and Production The total number of wells drilled in this district during 1944 is shown in Table 5. This indicates a 41 per cent increase in all drilling over 1943. In spite of every handicap created by the war, the oil industry more than met the crisis in its drilling program in this district. Last year we thought it would be impossible to add to the total number of wells drilled in the previous yea;, but in spite of the lack of manpower and materials this large increase was shown. During 1944 this district produced 124,201,978 bbl. of oil from 11,607 producing wells, whereas in 1943 it produced 88,421,693 bbl. from 11,211 producing wells. This is an increase of 35,780,285 bbl. of oil. Some decline has been shown in the older fields arid undoubtedly the majority of wells in the district are producing at too high a rate. However, this district has been able to meet any demands made on it by the Petroleum Administration for War for increased production. Discoveries and Extensions There was a slight decline over the preceding year in the number of wildcats drilled, but the number of discoveries increased. In most instances subsequent development has not been sufficient to arrive at preliminary valuations but it appears that the over-all oil discoveries were below normal and that the gas discovcrics were relatively more important. The Canolis and Tijerina pools, Jim Wells County, and the Dan Sullivan pool, Brooks County, appear to be the outstanding oil discoveries of the year. No important oil reserve was discovered or developed in the Wilcox horizons, although considerable wildcatting was done. Important extensions were made at Agua Dulce and Stratton in Nueces and Teleberg Counties. Production was increased appreciably at Willimar, Willacy County, and Seeligson, Jim Wells County, in sands and areas which were apparently productive at the beginning of the year. Refining Most of the major work in the changing and completing of refineries was finished this past year. Some of the most modern refineries in the industry are now located in the Corpus Christi area. Gas and Condensate No new recycling projects were commenced during the year, nor were there any important additions to the old operations. No major gas reserve was developed, although several new discoveries suggest potentid possibilities.

Jan 1, 1945

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

CONTENTS PAGE Rae, Colin C.-A Possible Origin of Oil. Discussed by S. Linker, Colin C. Rae... 2 Cottingham, Kenneth.-Subsurface Conditions on Portion of Arches Fork Anticline. Discussed by David B. Reger 6 Moyer, W. Irwin.-Time to Pay Out as a Basis for Valuation of Oil Properties. Discussed by H. J. Smith 9 Pogue, Joseph E.-Future Demands on Oil Industry of United States. Discussed by James O. Lewis 11 J. J. Walsh.-Coa-lmine Ventilation. Discussed by W. B. Daly, J. J. Walsh, R. R. Sayers, H. H. Stock, George S. Rice, James W. Paul, D. Harrington, T. D. Thomas 15 Longyear, Robert Davis.-Diamond-drill Sampling Methods. Discussed by Ira B. Joralemon, J. J. Rutledge, E. C. Harder 19 Joralemon, Ira B.-Sampling and Estimating Disseminated Copper Deposits. Discussed by J. Parke Channing, John E. Hodge, E.E. Hunner, B. B. Gottsberger, W. Y. Westervelt, W. O. Hotchkiss 20 Boericke, W. F.-Sampling and Estimating Zinc and Lead Orebodies in Mississippi Valley. Discussed by J. Parke Channing, Arthur Thacher 24 Daly, W. B. and Linforth, F. A.-Organization of Mine Sampling at Anaconda. Discussed by George A. Packard, W. B. Daly, B. B. Gottsberger 25 Norris, E. M. and Rahilly, H. J.-Mine Fires. Discussed by R. Dawson Hall, W. B. Daly, Frank Haas, D. Harrington, Robert E. Tally 26 Raymond, R. M.-Safety Practice for Hoisting Ropes. Discussed by B. F. Tillson, Graham Bright, Rudolph Kudlich, J. F. Howe, Robert Peele, H. G. Davis. 30 Howe, J. F.-Use of Wire Rope in Mining Operations. Discussed by Horace F. Lunt, J. F. Howe, B. F. Tillson 36 Tanner, W. N., and Jaccard, F. C.-Wire Rope and Safety in Hoisting at Butte Mines. Discussed by Horace F. Lunt, W. B. Daly, C. L. Colburn, William Kelly, Robert Peele, B. F. Tillson, Graham Bright, Charles E. Locke 38 Richardson, A. S.-Ventilation of Butte Mines of Anaconda Copper Mining Co. Discussed by D. Harrington, Chas. A. Mitke 42 Stuart, Charles E.-Storage-battery Locomotive as Applied to Mine Haulage. Discussed by Howard N. Eavenson, Charles E. Stuart, William Kelly, Arthur Thacher, W. H. Patton, Graham Bright 45 Woodward, C. D.-Electric Haulage Systems in Butte Mines. Discussed by William Kelly, Graham Bright, Howard N. Eavenson, C. E. Arnold, Gerard B. Rosenblatt, K. A. Pauly 47 Harrington, D.-Efficient Ventilation of Metal Mines. Discussed by R. E. Simpson 52 Otagawa, Masayuki.-Mining Methods at the Ashio Copper Mine. Discussed by Horace V. Winchell, D. W. Brunton 52 Stoek, H. H. and Clagett, Thomas H.-Coal Mining Methods. Discussed by P. D. Browning, G. L. Cox, Erskine Ramsay, Frank Haas, George S. Rice.

Jan 6, 1922

By Whitman E. Brown

The installation in 1948 of a Humphrey spiral concentrator section at the Hill-Trumbull plant of The Cleveland-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus 1/8 in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 44 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus 1/8 in. size. After desliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant.

Jan 1, 1949

By Bobby P. Faulkner

The Tennessee Copper Co.'s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966