Search Documents

By W. O. Philbrook

An engineering analysis indicates that the coke rate in present blast-furnace practice is set not by chemical or thermal needs but to give adequate charge permeability for economical driving rates. An equation showing interrelations among pressure drop, gas flow, and charge characteristics has been derived. Flooding conditions and the location of the fusion zone are discussed. Maximum ore size is probably limited by chemical re-ducibility rather than by heat transfer. THE intention of this paper is to show that the ].imitations on the production rate and coke requirement of the iron blast furnace are not primarily chemical or thermal in nature but are related to characteristics of the burden and operation that govern gas flow, heat transfer, and stock movement. A semiquantitative analysis will be developed in terms of standard engineering principles to give a useful picture of the relative importance of physical and mechanical factors in contrast with the chemical features of the process that are more commonly emphasized. Most of the details of calculation have been omitted in the interest of brevity and to avoid submerging the rnain points in a sea of arithmetic. Numerical values have been arrived at by objective methods from reported operating data or by reasonable estimates of material properties where exact data are lacking and then tested to see how well they fit practice, rather than by working backward to find what assumptions are needed to give the desired answers. The analysis is oversimplified in many ways because exact engineering relations have not yet been studied for bed distributions as complex as are known to exist in the blast-furnace stock column. One objective of this paper is to show that the blast furnace, in spite of its complexity, can be at- tacked by engineering methods in the hope that this viewpoint will stimulate the kind of research needed for a more exact treatment. The basic ideas and many of the conclusions presented are qualitatively well known. A careful literature survey to credit the source of all observations not original to the author would indeed be voluminous, and such has not been attempted. T. L. Joseph's Howe Memorial Lecture' gives an excellent background of what is known about the internal workings of a blast furnace. Other important reference works or sources of specific information will be noted. It is hoped that the present paper will contribute something new, in method of attack and interpretation, that will aid in a clearer understanding of how to operate the blast furnace to best advantage. Factors Limiting Production and Coke Rates The rate of combustion of coke in a blast furnace, as in any fuel bed, is exactly proportional to the rate at which air is supplied. It is axiomatic, then, that the production rate of a furnace is limited by the rate at which it will take wind, i.e., burn coke, and the amount of coke that must be burned at the tuyeres to make a ton of iron of suitable composition. These two possible limiting factors will be considered briefly in the order mentioned. One common restriction on wind rate is flue-dust production. Since the volume of top gas is nearly proportional to the blast volume (by a factor of about 1.35 on a dry basis), an increased wind rate causes a correspondingly increased linear velocity of top gas in the throat of the furnace. The higher

Jan 1, 1955

By P. S. Rudman

Crystal-structure occurrences in binary phase diagrams of fifth- and sixth-period elements, zirconium through palladium and hafniun through platinum, are surveyed with the conclusion that average .group number GN is the dominant correlative. This is interpreted in terms of curves of enthalpy differences between competitiue structures that are continuous func -tions of GN. It is further reasoned that the absolute formation energies may also be continuous functions of GN and if so can be simply obtained from the regatives of the heats of sublimation of the elements. It is shown that from such a heat of formation-GN plot the heats of mixing of alloy systems can be quantitatively predicted. For example, for sixth-period alloys very large exothermic heats of mixing are predicted for systems that span GN = 6 (i.e., Hf-Pt, Ta-Os, ...). Thermodynamic data with which to test these predictions do not appear to be available. If in the latter transition (A subgroup) elements we eliminate from consideration the fourth period where magnetic terms contribute to crystal-structure stability, as shown in Table I, there is a very regular sequence of structures. Using the group number (GN) assignments of Table I, which differ from the usual assignments of 8 to the elements listed as 8 through 10, it is perhaps trivial to say that the phase occurrence is a unique function of GN. However, the interesting aspect of alloys from among these elements is that the alloy structures also appear to correlate with GN. The GN for an alloy is given as GN = SixiGNi, where xi and GNi = atomic fraction and GN of component i, respectively. It is difficult to credit anyone in particular with having discovered this correlation, so many people have implicitly or explicitly employed it in the last 10 years. However, Bloom and Grant' in their correlation of s-phase occurrence with total number of d + s electrons were certainly one of the first to appreciate the correlation and Hume -Rothery2 appears to be responsible for the use of average GN as defined above. Only in the last few years have the phase diagrams of enough alloy systems been determined for this correlation to be surveyed with any degree of completeness. We shall here, in an abbreviated format, summarize the available phase-diagram literature and discuss some consequences of the GN correlation. BINARY DIAGRAM SURVEY In Figs. 1 to 3 the phase occurrences are summarized. In Fig. 4 the occurrence limits for the more common structures are summarized. That the GN of an alloy falls within the occurrence limits of a particular structure is a necessary but not a sufficient condition for the appearance of that structure. The preceding figures certainly illustrate that GN is a dominant correlative for structures of these elements. Many of the diagrams have complications, with ordering and other phase changes occurring in intermediate phases, that cannot be clearly accommodated in such a schematic survey and have hence been left out. Such omissions cannot, however, negate the GN correlations discussed here. Relative atomic size is also an important crystal-structure determinant and since atomic size varies quite regularly with GN for these elements it is possible that the apparent GN correlation is basically a size correlation. In Fig. 5 relative size occurrence limits are given for intermediate phases and extended terminal solutions. The relative volume, ?v/(v) - 2(vA - vB)/(vA + uB), has been taken as the measure

Jan 1, 1968

By Marcus Nadler

WAGES in the United States, in spite of the wage freeze, have increased materially. Overtime payments have become standard practice in almost all industries. Now efforts are being made to place wages on an annual basis, and if this is adopted, it will result in an increase in the cost of production. Organized labor today is more powerful than ever before; union membership is large and steadily increasing, and in many instances membership in the union is a prerequisite to employment. The treasuries of many unions are strong as a result of the large membership and full employment. The unions, therefore, today are in a much better position than ever before to carry on long strikes. Politically, too, the unions are more powerful today than they ever were. On the basis of their strength, one may expect that some of the demands that the labor unions will make in the not distant future will be granted. It is, therefore, quite evident that before long, particularly when the curtailment in war production reaches about 40 per cent, this country will be confronted with a serious labor problem.

Jan 1, 1945

By E. F. Young

The Porter Tunnel will open up 10 million tons of coal for Philadelphia & Reading which can be taken without hoists or pumps.

Jan 3, 1951

By Lewis E. Dr. Young

MINING engineers in the United States understand that mining conditions in the British coalfields are much more difficult than in most of the mines now being operated in the United States. We realize also that in the near future we must face some of these same difficult problems. Early Mechanization The progress made in mechanical loading in the United States is the result of a long struggle in many coalfields to mine with power tools safely and to increase output per man-shift. Attempts to use power to loosen coal and to transport broken coal in the U. S. may be said to date from the Stanly Header, or Entry-Driver brought from England in 1888. The principle of this boring machine was used in the McKinlay Entry-Driver, almost continuously used in the U. S. since 1920. Since 1888 experimental loaders, scrapers, and conveyors were installed with more or less success. Beginning in 1918, considerable progress was made with mobile loaders, and in 1920 the first wage agreement for the operation of mechanical loaders was made in Indiana. In 1923 the Pocahontas Fuel Co. loaded nearly 1 million tons of coal using 23 Coloders. Labor Policy The United Mine Workers of America have never officially opposed the Mechanization movement. On December 10, 1945, in a statement before the House of Representatives Labor Committee, John L. Lewis said, regarding the policy of the United Mine Workers of America: "We have welcomed progress; we have welcomed machines. We have told our people that they had to accept that condition; that it was the process of progress, and that they would have to take their chances." Recent Development In 1951 about 71 pct of the tonnage mined underground was mechanically loaded. Over 4000 shuttle cars are in service and it is estimated that much more than half of the tonnage loaded underground is produced by trackless mining. In 1947 roof-bolting was introduced extensively and it is estimated that more than 2 ½ million bolts are now being used per month in about 600 mines. The use of roof bolts has permitted the more effective and safer use of loaders and shuttle-cars. Continuous Mining The McKinlay Entry-Driver could have been used for continuous mining, but for many years it was used only .for entry driving. In 1946 the Silver machine was developed in Colorado, and in 1947 this was acquired by the Joy Mfg. Co. and called the Joy Continuous Miner. Other types of combination mining-loading machines which eliminate drilling and blasting operations are the Marietta Miner, the Colmol, the Lee-Norse Miner, the Junior Miner, the Goodman and the Konnerth machines. There are several other types in the process of development. Probably by January 1953 there will be about 250 continuous miners in operation in the U. S. Payment of Mine Labor One of the most important problems in mechanizing was the establishing of rates of pay that would be attractive to the best men. Prior to the installation of mobile loaders the hand loaders and cutters have been paid by the ton. It was felt that a system of a day's pay should be established and that piece and tonnage rates should be abolished completely. Without exception, all coal loaded in mines equipped with mobile loaders is prepared and loaded by men paid an hourly rate. Trends in Mining Research There are two diverse approaches in coal production research; to try to design a mining machine to fit current methods, or to adapt mining practice to take advantage of proven machines. A great deal of credit must go to the mine operators who have been enterprising and dynamic enough to use available equipment intensively and to discard it as soon as an improved or new machine is available. Effect of Changing Markets Formerly there was an important demand for lump and prepared coal in the larger sizes for domestic use. The use of bituminous coal for house heating has decreased so that not more than 19 pct of the annual tonnage goes to retail trade, only 12 pct is used by the railroads, and much of the retail and most of the railroad coal is in stoker size. As a result of this decline in the market for coarse coal most of the large mining operations have crushers installed in the tipples or preparation plants. Mass production at the face requires increased preparation facilities. Another important trend is in connection with complete seam mining with mechanical loading. In many mines where the immediate roof is apt to fall with the coal no effort is made to separate roof material from coal prior to

Jan 1, 1952

By Captain Lyle

I was very much interested in Mr. Macdonald's paper, and I can say that there is nothing in it to which I cannot heartily subscribe. In speaking of the want of knowledge that has existed, and still exists, among engineers in regard to structural materials, their strength, etc., my own experience has taught me to doubt the reliability of the ordinary testing machines.

Jan 1, 1882

By James H. Boettcher

INTRODUCTION A complex interaction of worldwide economic and political forces is increasingly requiring 3 primary participants for the successful development of large natural resource projects in developing countries. They are the host government of the developing country (the "host government"), one or a consortium of international natural resource companies, (the "Resource Company") and one, or more likely, a syndicate of international lenders. The host government typically controls the rights to its country's natural resources and establishes the economic ground rules for their development. However, because of worldwide inflation and the depletion of easily accessible, high-grade resources, the nominal and real capital development and operating costs of projects have been spiraling. Moreover, the depletion of high-grade and mineralogically uncomplicated resources also raises the technical and operating risks associated with resource recovery. Thus, despite increasing political self-consciousness and economic nationalism in developing countries, international resource companies are still often necessary project sponsors since they can provide, among other things, the required technical and management expertise and equity capital. The presence of these factors, and often the addition of worldwide market access in a project, is often critical in determining whether or not the project will be considered creditworthy by international commercial lenders. The international commercial lender is often the critical third party in project development, due in a large part to the ever escalating-costs of project developments relative to the financial resources of many companies and even a growing number of countries. In addition, lenders have other reasons for taking more than a passive interest in all aspects of a project's development. These reasons include the following: 1. Projects are often financially structured such that the primary security for a loan, once completion and performance standards are met, is the cashflow of the project rather than recourse to its sponsors. 2. Lenders, in addition to the "project risk" just described, are frequently asked to assume various elements of "political" risk which nay put them in a sensitive economic position between the host government and international resource firms (This is discussed later). 3. International banks today have large loan portfolios of developing country debt with final maturities ranging from one to fifteen years. The various current projects undertaken are the building blocks of most developing country economies that will hopefully contribute to the long run economic development of a country as well as generate the foreign exchange necessary to repay foreign loans in the future. In this regard it is useful for lenders to realize whether a given project "makes sense" in terms of a country's natural resource endowments and competitive advantages over other countries. The type of framework discussed in this article would help lenders to better make such assessments. In order to facilitate the continued international flow of capital and technology to developing countries and of readily available supplies of raw materials from them, it is important for each of these three parties to increase its awareness of the goals and objectives of the other parties as well as the bargaining process that results in the legal, financial, credit and fiscal structures by which a joint venture project ultimately proceeds. Each of the parties faces increasingly complicated accept/reject decisions when they are faced with difficult choices among. a wide range of alternative structural combinations each of which has different implications for risk and reward to them. Therefore, by increasing the mutual, 3-way awareness of the decision processes of the other parties, it should be possible to: • provide better information and results in the formation of more rational expectations by all parties going into negotiations, • facilitate the project formulation process by allowing parties to focus more clearly on the areas of common interest and conflict, • result more frequently in final structures and agreements that better reflect the economic and political realities associated with a project and thus • result in more creative, innovative agreements that should reduce the need for changes to them and thus promote the kind of long run political stability conducive to attracting capital and further investment.

Jan 1, 1982

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965

Geological Survey of the State of Maine, Orono, Me. Joseph Conrad Twinem, State Geologist In the years 1837, 1838, 1839, Charles T. Jackson made three reports on the geology of Maine Reports were made in 1861-1862 by C. H Hitchcock entitled, respectively, "General Report on the Geology of Maine" and "Geology of Maine." These old reports are now out of print

Jan 1, 1933

By John A. Church

AT a time when the treatment of gold and silver ore9 by fusion, in opposition to the mill-process, is attracting so much attention in this country, it may be useful to consider what is done in a well-conducted foreign work. For this purpose I will ask the reader to accompany me to Lend, in Austria, a small but thoroughly organized

By John A. Church

AT a time when the treatment of gold and silver ores by fusion, in opposition to the mill-process, is attracting so much attention in this country, it may be useful to consider what is done in a well-conducted foreign work. For this purpose I will ask the reader to accompany me to Lend, in Austria, a small but thoroughly organized

Jan 1, 1873

By Gerald C. Mathis

FERGUS County, Mont., shown in Fig. 1, is known for its once famous gold mines near the old towns of Gilt Edge, Maiden, and Kendall. But at Heath, a small farming community near the foot-hills of the Snowy Mountains, thousands of tons of gypsum have been mined since 1916. The value of the gold taken from the mines of Fergus County runs into millions of dollars; the value of the products made from the gypsum of the Heath mine is also in the millions. The gypsum mine will continue to produce for many years, while the gold mines are closed today.

Jan 2, 1953

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570°and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1984

By Homer Staley

THE casting alloy 88 copper, 10 tin, 2 zinc, commonly known in England as Admiralty metal and in this country as Government bronze, gun metal, or Naval Department composition G, has, at its best, many valuable properties. However, its physical properties are known to vary widely with slight changes in method of manufacture of the castings, such as slight variations in composition, variation in pouring temperature, kind of mold used, method of pouring and gating of molds, size and shape of castings, amount and kind of heat treatment., and so forth.1 The microstructure of castings made from this alloy is influenced by slight variations of composition, rate of cooling, and kind and length of heat treatment. This is best understood by reference to the equilibrium diagram. The part of the diagram in which we are interested and the effect of the thermal equilibrium relations on the physical properties of the alloy 88 copper, 10 tin, 2 zinc, have been discussed by Hoyt, Camp-bell, Primrose, and Rawdon.2 In Fig. 1 is given the equilibrium diagram of the copper-tin alloys. Briefly stated, the relations of composition and temperature changes are as follows. Compositions between A and a consist of but one constituent-the a bronze, which is a, solid solution of copper and tin, rich in copper. On cooling from the molten state these compositions gradually crystallize, at temperatures above 790°, into a mass of interwoven tree-like crystals or dendrites. The cores of the dendrites are rich in copper and the percentage of tin gradually increases as the surfaces are approached. As cooling progresses, after all the metal has crystallized, no further changes occur, in the crystals other than diffusion within the crys-

Jan 9, 1919

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way 'to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgC03) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1951

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By G. R. Fitterer

By means of the C-Sic thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. Commercial Development of This Device Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, procedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; nevertheless, it is felt that satisfactory gains have been made, inasmuch as each installation has indicated some effect of temperature upon the metallurgical operation, and has pointed the way toward technical and financial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-Sic thermocouple and the temperatures measured are discussed later in this paper. Temperature Variations or Liquid Pig Iron One well-known discussion between the blast-furnace and open-hearth (or Bessemer) departments has occurred intermittently for more

Jan 1, 1936

By G. R. Fitterer

By means of the C-Sic thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. Commercial Development of This Device Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, procedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; nevertheless, it is felt that satisfactory gains have been made, inasmuch as each installation has indicated some effect of temperature upon the metallurgical operation, and has pointed the way toward technical and financial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-Sic thermocouple and the temperatures measured are discussed later in this paper. Temperature Variations or Liquid Pig Iron One well-known discussion between the blast-furnace and open-hearth (or Bessemer) departments has occurred intermittently for more

Jan 1, 1936

By Earle C. Waite

THE Industrial Minerals Division this year held no individual sessions of its own except the business meeting Tuesday afternoon. One session was held jointly with the Society of Economic Geologists, one with the Milling Methods Committee, and two with the Society of Economic Geologists and the Mining Geology Committee. At all of these meetings the attendance was better than usual and the Tuesday afternoon session, with nearly 400 present, probably set a new record for the Division. Joint sessions seem extremely popular when papers of mutual interest are presented. On Monday afternoon, mica was the predominating subject. The North Carolina mines provided most of the information presented, although the discussion brought out similarities with the New England mines. B. C. Burgess particularly stressed the fact that with the existing curtailment of mica from India it is necessary to get the most mica in the shortest time from the mines in this country. He said that the Colonial Mica Corp. hopes to have 1000 mines operating in the near future. This seems a great number, but when one considers that these mines employ from 3 to 28 men, mostly nearer the low figure, the output of each mine is relatively small. Although the price of mica is from six to ten times the prewar price, the yield of 8 to 150 lb. of mica per ton of raw ore does not provide high returns to the producer.

Jan 1, 1943