Search Documents

By D. Argyriades, G. Derge, G. M. Pound

The electrical conductance of molten FeS was studied as a function of temperature and composition. It was found that stoi-chiometric FeS (36.5 pct S) shows a minimum specific conductance of 400 ohm-1 cm-1. For the Fe-rich melts the conductivity increases with increasing amount of iron to about 4850 ohm-1' cm-I at 26 pct sulfur. For the sulfur-rich melts the conductivity increases with increasing amount of sulfur until it reaches a maximum of 1300 ohm1 cm-1 for 37.4 pct S and decreases to 800 ohm-1 cm-1 for 38.3 pct sulfur. It is concluded that molten stoichiometric FeS is an intrinsic semiconductor in which the forbidden gap in the electron energy level diagram is quite narrow. Excess sulfur acts as an acceptor impurity in providing a component of positive hole conduction, while excess iron acts as a donor impurity to increase the n-type conduction. K. Bornemann and G. von Ftauschenplatl used a four-terminal, direct-current cell to study the electrical conductance of molten copper sulfide. Their measurements showed a high conductivity, of the order of 100 ohm-1 cm-" and a positive temperature coefficient. From electrolysis studies, Savelsberg2 concluded that molten Cu2S and molten FeS are electronic conductors. Further. he found that molten FeS has a high specific conductance, of the order of 1500 ohm-' cm-', and a small negative temperature coefficient. Pound, Derge, and Osuch,3 using an ac Kelvin circuit and a four-terminal cell, measured the specific conductance of molten Cu,S, molten FeS, and various mixtures. They found that the specific conductance of the solutions followed a roughly additive rule of mixtures. Yang, Pound, and Derge4 showed from electrolysis measurements that the mechanism of electrical conduction in molten Cu2S, FeS, and mattes is primarily electronic. Further, they observed that small additions of CuCl suppress the electronic conduction whereupon the system behaves ionically.

Jan 1, 1960

By F. S. Norcross

DEVELOPMENT of the manganese deposits of Cuba is a matter of importance not only to those involved in this industry on the Island but to the United States steel industry and to our Nation as a whole. For years our domestic resources of manganese have been wholly inadequate, but the recent Cuban development points the way toward solution of this strategic mineral problem.

Jan 1, 1939

By Donald M. Liddell, G. C. RIDDELL

THE cosmic ray continues to engage the attention of the physicists, and according to Millikan and Compton, experiments of the past summer indicate that these rays must come from interstellar space, but not from the stars themselves. According to press reports of the International Congress of Physicists at Rome, the view was given there that these rays have an initiating potential of over 750,000.000 volts. In the field of spectrographic investigation great strides have been made. The U. S. Naval Research Laboratories (R. F. Mehl and G. E. Doan of Lehigh) have just finished a year's work with a "radium torch" or "shadowgraphic apparatus" in the field of the X-ray, that bids fair to displace the latter to a great extent. The torch is more powerful., easier to operate and cheaper. Penetration of 10 in. of steel has been accomplished, which. is much -beyond the- -scope-, of the X-ray..

Jan 1, 1932

By W. L. Zeigler

THE year 1930 in the Ceur d? Alene district was one of curtailment in production. Many of the small properties were closed entirely and only three large. producers, the Bunker Hill & Sullivan, Hecla, and the Morning mines were left producing at capacity. No innovations in milling were evident, but progress was made in reducing costs as is always necessary in times of low metal prices. One new concentrator was constructed, a 500-ton daily capacity selective flotation plant for, the Jack Waite Mining Co. This mill uses coarse crushing, followed by hand sorting, for both a high-grade ship- ping ore and waste. The remainder of the ore leaving the sorting belt is crushed in a new type Traylor reduction crusher to %-in. size and stored in large capacity mill ore-bins. The grinding is done with ball mills, in closed circuit with a Dorr classifier to 75 per cent - 200 mesh. Minerals Separation 24-in. flotation machines are used both for a lead and a zinc concentrate, with double cleaning in each case. The concentrates are dewatered in Dorr thickeners and filtered on Oliver late-type filters.

Jan 1, 1931

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5'798'14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970

By Kenneth A. Moon

An exact statistical treatment of a one-dimensional model is used as a basis for evoluating the reliability of certain simplified expressions for the activity of the solute in interstitial solutions, including one obtained from the exact expression by setting the repulsive interaction equal to infinity. The latter approximation is found to be satisfactory at low and moderate concentration if the repulsive interaction is large, even though not infinite. A similar expression (identical if the co-odination number is two) is derived from the quasichemical expression of Lacher, and is recommended as the best available expression for the excess configurational entropy of interstitial solutions with excluded sites. Some reasonable models are discussed, and the nature of the saturated solutions is determined by inspection. Some of the models reduce to the one -dimensional case. An analysis is given of the excess partial entropy of hydrogen in V-H; Nb-H; and To-H solutions. MOST treatments of the statistical thermodynamics of interstitial solid solutions have followed the classic paper1 of Lacher in making the simplifying assumption that the configurational entropy of the solution is ideal. However, it is becoming increasingly apparent that there are many interstitial solutions with very large so lute-solute repulsions, and for these the assumption of ideal entropy is not valid or useful. It is important to realize that with substitutional solutions large repulsions between the component atoms must lead to phase separation, whereas in interstitial solutions the free energy of the solution is not drastically increased by large solute-solute repulsions until intrinsic saturation is reached at the concentration where further solute would be forced to enter a site in which it would experience the repulsive effect of one or more solute atoms already present. In the limiting case of an infinitely large repulsive interaction, the excess free energy would be attributable entirely to excess entropy, the enthalpy of mixing being zero. AS will be shown below, even if the repulsions are less than infinite, a treatment based on an assumption of infinite repulsions may be very satisfactory up to moderately high concentrations of the interstitial component. Often in solutions where large repulsive interactions exist, there are also small interactions — often attractive—between solute atoms in configurations other than that corresponding to the large repulsion. In such cases the excess free energy will consist of an excess entropy term attributable to the large repulsive interactions, and an enthalpy term corresponding to the other small interactions. Nomenclature to differentiate succinctly between important cases would be a convenience. In this paper the nomenclature shown in Table I will be used. In Table I, and in the preceeding discussion, excess quantities are defined in terms of standard states which are pure solid solvent and pure (possibly hypothetical) solid saturated phase of the structure in question. In practice, it is more convenient to choose the interstitial element as a component, and its conventional standard state. This will add a composition-independent term to the excess entropy and the enthalpy. The earliest paper known to the present author which treats the thermodynamics of athermal interstitial solutions was given by schei12 in 1951, but the statistical derivations in that paper are open to criticism. Speiser and Spretnak were the first to give a correct statistical treatment,3 limited, however, to concentrations sufficiently low that the number of empty sites excluded from occupancy by more than one filled site is negligible. The purpose of the present paper is to extend the statistical treatment to more concentrated solutions, and to examine the magnitude of the errors introduced by assuming that the repulsive interactions are infinite when in fact they must be finite. THE QUASICHEMICAL APPROXIMATION Fortunately, a standard method already exists for taking into account the effect of large interactions upon the entropy of mixing. This is the quasi-chemical method, in which the probability of existence of a given pair of solute atoms in a certain proximate configuration is assumed to be proportional to exp(-w/kT), where w is the energy increase of the solution when the two atoms are moved from isolated locations in the solution to the configuration in question. A quasichemical treatment of interstitial solutions was given in 1937 in a widely neglected paper by Lacher.4 The result comes out

Jan 1, 1963

By D. E. Mikkola, G. E. Poquette

X-ray diffraction was used to study the growth of antiphase domains in quenched (or "disordered&apos;? Cu3Au annealed in the range 300" to 385°C. Measurements of the long-range order parameter indicate that a high degree of order is established rapidly at these annealing temperatures. Average domain sizes obtained by Fourier analysis of the superlattice peak profiles show that antiphase domain growth is analogous to classical metallurgical grain growth (i.e.,fol-lows a D2 US kt relation). The activation energy for the growth process, 44 kcal per mole, indicates diffusion control. The anisotropy in the observed effective domain sizes from seven different superlattice peaks can be best accounted for by a configuration involving antiphase domain boundaries on {100 } and (111 ) planes, where the (100) boundary is the low-energy type, {lOO} Type I. The disappearance of the (111) antiphase domain boundary during domain growth is dif-fusion-controlled with an activation energy of 48.5 kcal per mole. On the other hand, the behavior of the parameter representing the amount of (100) Type I boundary indicates that there may be a conversion of the higher-energy boundary types to (100) Type I boundary during the growth process. THE order-disorder transformation in the alloy Cu3Au has been the subject of numerous experimental investigations over the past 40 years, most of which have involved measurements of convenient physical properties such as resistivity and hardness as a function of heat treatment. The interpretation of these data is difficult because measurements of this type have the disadvantage that they yield total changes resulting from several different atomic processes which may be occurring simultaneously. The present study was undertaken to establish by means of X-ray diffraction the kinetic behavior of one of these atomic processes, namely antiphase domain growth. In the completely ordered state Cu3Au has an L12 structure which can be described as an fcc type arrangement of atoms in which the gold atoms occupy the corner sites and copper atoms the face-centered sites. Three other equivalent unit cells can be formed by allowing two gold atoms to occupy opposite face-centered sites and copper atoms to occupy the remaining corner and face-centered sites. These four different unit cells are crystallographically related by a shift of 1/2<110>. Quenching from above the critical temperature (392°C) to room temperature retains the "disordered" structure-a "random" arrangement of copper and gold atoms having the fcc structure. Annealing the disordered alloy below the critical temperature causes ordering to occur through the nucleation and growth of ordered regions at different points throughout the crystal. These small ordered regions, each based on one of the four types of unit cell, grow by consuming the disordered material until they impinge to form a domain structure in which the domains are antiphase by a shift of 4(110). The boundaries between domains are called antiphase domain boundaries (APDB) and they have been found to lie primarily on &apos; {100} planes in highly ordered Cu3Au. Two types of APDB can occur on ( 100) planes. An example of an (001)1/2[110] shear type APDB is shown in Fig. I. Because of the layer of copper atoms separating the domains in this case, there are no near-neighbor violations across the boundary and it has a low surface ener This type of APDB will be referred to as {lOO} Type I. Fig. 2 shows an (001): [011] climb type APDB, (100) Type 11. This type of APDB can be described as resulting from removal of a (200) plane followed by a shift of 1/2<110> to bring the separated regions together. Near-neighbor violations across (100) Type I1 APDB make it a high-energy boundary. There are numerous other possible APDB configurations; however, it is only worth noting that shear type APDB can be produced on the (111) plane by motion of a normal fcc dislocation with Burgers vector 1/2<110> through the ordered structure. A (111); [110] shear type APDB is shown in Fig. 3. Again, because of the near-neighbor violations this type of APDB has a higher energy than the (100) Type I APDB.

Jan 1, 1970

PROF RICHARD ÅKERMAN Stockholm, Sweden ANDREW CARNEGIR New York, N.Y. PROF HANS HOEFER Leoben, Austria PROF HATON DE LA GOUPILLIERE Paris, France PROF HENRI LOUIS LE CHATELIER New York, N.Y. M FLORIS OSMOND Paris, France PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF DR HERMANN WEDDING Berlin, Germany

Jan 1, 1910

By Arnold Hoffman

A RESPONSIBLE steel executive recently declared that scrap shortages, despite fantastic prices reaching up to $50 per ton, are responsible for the loss of 140,000 tons of steel a month and that in March 1947 alone 25 more steel furnaces could have been operating were it not for scrap scarcities. His answer to this serious situation was to ask for a speedier flow of scrap and also abolition of Government control over pig iron distribution. It would be more logical, perhaps, if an answer to this growing problem of scrap deficiency were sought within the steel industry itself. As long ago as 1933, L. B. Lindemuth, a consulting steel metallurgist, warned the steel industry that a shortage of scrap was inevitable and that beyond 1938, adequate supplies for open-hearth furnaces could not be expected. The outbreak of war, with consequent phenomenal demands on the industry, accelerated production of steel and further worsened the scrap situation. Today we are suffering from a condition which could have been prevented had the industry been more far-seeing and provided for an inevitable contingency. However, better late than never, and measures can now be taken to alleviate permanently scrap shortages in the future. This can be done by greater utilization of heavy sinter which experience proved is an excellent substitute for scrao and lump ore.

Jan 1, 1947

By S. C. Dhara

A process of solvent extraction and separation of platinum group metals (PGM) and gold using primary, secondary, tertiary, and quarternary organic amines has been briefly described. The effects of amine structures; the use of diluents; the principle of synergism and antisynergism in the mixed extractants; the oxidation states of metal ions are explained in the amine extraction process of precious metals.

Jan 1, 1984

By Rudolf Gahl

SOME time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanuers in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to. be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but. varying the adjustments of the vanner .from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 2 3/8 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it .was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Sep 1, 1909

By Young C. Kim, Francis Martino, Ish Chopra

For the past two and one-half years, various emission control strategies were jointly developed by the University of Arizona and the Homer City Owners to com- ply with the clean air requirements at its Homer City Power Plant. Some of the available options for the SO2 emission control by the Homer City Owners were:l)cleaning of run-of-mine coal,2) scheduling of mining operations at its captive mines, 3) blending the captive mine coal with externally purchased low sulfur coa1,and 4) placing a partial FGD system. This paper describes two specific emission control strategies developed and implemented. These are: 1) production scheduling at the mining face to minimize sulfur variability, and 2) external purchasing of low sulfur coal for further blending. The main objective of this paper is to share our experiences on implementing the developed strategies. This paper emphasizesthe need for proper mine planning on a short-term basis, if the power plant is to meet the desired objective.

Jan 1, 1983

By AIME AIME

WHEN your good secretary was kind enough to ask me to speak tonight I was rather reluctant to do so lest it be just another case of a man who has been abroad inflicting himself on his friends. So if anybody wants to walk out on me it will be perfectly all right. In the matter of statistics, geography, geology, and the like, you can get more from an encyclopaedia than I can tell you. For that reason I want to restrict myself to mentioning just a few personal impressions of that great country, Australia. About ten days ago I met the professor of mining from the University of Adelaide. In our conversation, which ran into a discussion of the relative characterstics of the two countries, he asked me whether it was fair to think of Australia as a land of strikes and not think of the United States as the home of murderers, bootleggers, and gangsters. At any rate those are the things most prominently played up in the news from the respective countries, so you can see how distorted our conceptions can be.

Jan 1, 1931

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.1 It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to be drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the ?&apos; phase," CuA12." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in ?&apos; lying parallel to this plane are roughly similar to those opposite it in the matrix.&apos; The formation of ?&apos;, however, is preceded by the formation of a transition lattice ?&apos;, which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly perfect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.4-8 Particles of ?&apos; may be recognized microscopically and form a well-defined Widmanstätten figure.* The ?&apos; lattice is recognized by the occurrence of diffraction lines on powder photograms or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6.7,1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a few hundred atoms in diameter, probably of the composition of "CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact merely ?&apos; in a high state of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By S. F. Emmons

This mine is situated upon the western slope of the Meadow Valley mountains, about 70 miles by road from the present end of the railroad-track, which is at Uvada, on the UtahNevada boundary. This boundary-line marks fairly well a certain change in type of scenery from western Utah to eastern Nevada,—from a region in which the desert valleys predominate over the mountain ranges to one in which they are in about equal proportion. The railroad from Salt Lake City runs somewhat W. of S., for the most part along the bottom of the ancient Lake Bonneville. The latter part of its present course follows the axis of the southern arm or bay of that lake, now known as the Escalante desert. Along this bay, its line is a mathematically straight one, with no perceptible change of level for two " tangents " of more than 30 miles each, varying but a few degrees in direction. In the four or five hours re-

Jan 1, 1902

By D. R. Uhlmann, T. P. Seward, O. Chalmers

A magnetic field has been used to damp out liquid convection during the solidification of castings. Ingots of Al-2 pct Cu were poured from various sperheats (10" to 65°C) into a room-temperature graphite mold located between the poles of an electromagnet. The effect on ingot structure of varying the strength and time of application of the magnetic field was investigated, and the results are interpreted in light 01- current theories of ingot structure. In the solidification of alloy systems, thermal gradients in the melt and differences in density of the constituents are expected to produce convective motion in the liquid. The thermal convection caused by temperature gradients should be present during the freezing of both alloys and pure materials, while the solute convection caused by density differences should be of concern only for alloys. The possible influence of this natural convection on the structure of castings has been discussed by Ruddle,&apos; Chalmers, and Tiller. More recently, an experimental investigation of such effects was carried out by Cole and Bolling. These workers took stationary molds containing lead- and tin-based alloys and. using a brine solution. quenched them from various superheats above their respective liquidus temperatures. When grids were placed across the mold diameter to suppress convection, the grid region was later observed to contain a larger percentage of columnar grains than other parts of the casting or than similar castings poured without the grids present. From thermocouple measurements, they found the temperature in the grid region to be higher than that in the region outside the grids throughout the freezing process, and concluded that convection should be an important mode of heat transfer in normal castings. In addition to such convection arising from thermal gradients or differences in density of the constituents, a further source of convective motion, which we shall call "momentum convection", may be particularly important in small (laboratory-size) castings. By this term we refer to the convective motion produced in the initial pouring process, a motion which is damped out as the linear momentum and angular momentum of the liquid are dissipated. Besides these sources of convection, which are present to some extent in all castings. external influences may also be effective in producing convective motion. Examples of such "forced" convection which have been discussed in the literature include stirring the melt, shaking the mold, rotating the mold, and so forth The purpose of the present study was to examine the effect of convection on the structure of castings poured into a cold mold. In this work, a magnetic field was employed to damp out the convective motions within the liquid, and hence control the extent of con- The effect of a magnetic field on convective currents in a conducting liquid is to induce eddy currents which oppose and damp out the convective motion. vection. The technique of magnetic damping was previously used by Utech and F1emings" in their study of convective effects on impurity banding and other substructure in alloy crystals grown unidirectionally from the melt. In their investigation, fields as small as 200 gauss were found to be effective in damping the convection currents which influence the banding. I) EXPERIMENTAL TECHNIQUE In the present study, alloys of A1-2 wt pct Cu were poured into a room-temperature graphite mold. The mold, in the shape of a circular cylinder, 2 in. ID, 2-3/4 in. OD, 5 in. inside height, and 5-1/2 in. outside

Jan 1, 1967

By J. H. Craig

As a result of information that the Navy Department was questioning the advisability of raising the maximum allowable exposure temperature for zinc-coated steel parts from 500 to 750 F., it was decided to make a series of high temperature tension tests on several types of uncoated and zinc-coated steels. The objective was to determine at what temperature intergranular penetration of galvanized steel by zinc might take place under conditions of rapidly applied stress and temperature. Tests were conducted in the range from room temperature to 1400 F. In this range, low-carbon and high-carbon steels did not suffer any adverse effects due to zinc coatings. In fact, at 1400 F. the zinc coatings appeared to have a beneficial effect. In stainless steel, the coating had no effect up to 1000 F. Above this temperature, the zinc coating appeared to cause a marked loss in ductility and a less pronounced loss in strength. There was no visible evidence of zinc penetration of the stainless steel structure, but it was assumed that this was the cause of the adverse effect.

Jan 1, 1945

By George Fowler

THE history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur Co. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico.

Jan 1, 1934

By A. J. Phillips, C. G. Grant, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

Aamot, Olav Crone, Research Engr., Norsk Elektrokemisk Kongensgt, 18, Oslo, Norway ?29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. &apos;04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. &apos;15 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. &apos;28 Abel, Walter D., Cons. Engr 364 S. Cloverdale Ave., Los Angeles, Calif. &apos;32 Abele, Louis T 1457 Euclid Ave., Zanesville, Ohio. &apos;31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada. &apos;31 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. &apos;19 Abraham, W. E. V., East India United Service Club, 16 St. James&apos; Sq., London, S. W. 1, England. &apos;28

Jan 1, 1936