Search Documents

By N. A. Gokcen, J. Chipman

Aluminum and oxygen dissolved in liquid iron were brought into equilibrium with pure alumina crucibles and atmospheres of known H2O and H2 contents to study the reactions: 1—Al2O3(s) = 2 Al + 3 0; 2—Al2o3(s) + 3H2(g) = 2Al+ 3H2o(g); and 3—H2(9) +O = H2O(g). Aluminum strongly reduces the activity coefficient of oxygen and similarly oxygen reduces that of aluminum. Values of the product [% All" • [% O]3 are much smaller than those found in previous experimental studies and are of the order of magnitude of the calculated values. ALUMINUM is the strongest deoxidizer commonly A used in steelmaking, but the extent to which it removes dissolved oxygen has been debatable. The relationship between aluminum and oxygen has not been determined reliably not only on account of the usual experimental difficulties at high temperatures but also because of uncertainties in the analyses of very small concentrations of oxygen and aluminum. The earliest experimental attempt of Herty and coworkers' was followed by a more systematic study of Wentrup and Hieber.' These authors added aluminum to liquid iron of high oxygen content in an induction furnace and considered that 10 min was sufficient to remove the deoxidation products from the melt. Parts of the melts thus obtained were poured into a copper mold and analyzed for total aluminum and oxygen (soluble plus insoluble forms), assuming that the insoluble parts were in solution at the temperatures from which samples were taken. It is conceivable that the furnace atmosphere in their experiments, consisting of mainly air at 20 mm Hg pressure, was a serious source of continuous oxidation and therefore that their oxygen concentrations were correspondingly high. Scattering of their data was explained to be well within the maximum inaccuracy of 10°C in the temperature measurements and errors of ±0.002 pct each in the oxygen and total aluminum analyses. Maximum and minimum deoxidation values, i.e., values of the product [% All' . [% O] differed by factors of 10 to 15; mean values of 9x10-11 and 7.5x10-9 ere reported at 1600" and 1700°C, respectively. Hilty and Craftsv determined the solubility of oxygen in liquid iron containing aluminum, using a rotating induction furnace. Pure alumina crucibles used in their experiments contained the liquid iron which in turn acted as a container for slags of varying compositions consisting mainly of Al2O3, Fe2O3, and FeO. The furnace was continuously flushed with argon, and additions of aluminum and Fe2O3 were made in the course of each experimental heat. The inner surfaces of their alumina crucibles were covered with a substance other than pure Al2O3, containing both iron oxide and alumina. Although frequent slag additions can change the composition of slag in the liquid iron cup formed by rotation, the inner surface of the crucible must depend upon the transfer of oxygen or aluminum through the liquid iron for any adjustment in composition. It is not clear that their metal was in equilibrium with the crucible wall, but it is clear that it was not in equilibrium with Al2O3. Their deoxidation product, [% A].]" • [% O]3, varied by a factor of more than 50; the average values of 2.8x10- and 1.0x10-7 were selected for temperatures of 1600" and 1700°C, respectively. Aside from the experimental determinations, attempts have been made to calculate the deoxidation constant for aluminum indirectly from thermody-namic data. Schenck4 combined the thermodynamic data for Al2O3 and dissolved oxygen in liquid iron by assuming an ideal solution. His calculated values are 2.0x10-15 and 3.2x10-13 at 1600" and 1700°C, respectively. Later, Chipman5 attempted to correct for the deviation from ideality and derived an expression which led to deoxidation values of 2.0x10-14 and 1.1x10-12 at 1600" and 1700°C, respectively. The errors in these treatments originate mainly from inaccuracies of thermal data and uncertainties regarding the activity coefficients of dissolved oxygen and aluminum. The purpose of this investigation was to study the equilibria represented in the following reactions in the presence of pure alumina: Al2O3(s) = 2Al + 3O K = aAl2.ao3 [1] Al2O3(s) + 3H2(g) = 2Al + 3H2O(g) H2O K2 = aAl2(H2O/H2 ) [2] H2(g) +O = H2O(g) K3 = 1/ao (H2) [3] The experimental method consisted of melting pure electrolytic iron, usually with an initial charge of aluminum, in pure dense alumina crucibles under a controlled atmosphere of H,O and H2 and holding

Jan 1, 1954

By R. E. Delavault, H. V. Warren

In normal soils there are usually 10 to 50 parts of copper in every million parts of .soil. Only 0.2 to .5 pct of this copper can be found by any simple cold chemical attack. Now, with rubeanic mid reagent paper, a prospector or field geologist can detect as little us 4 ppm of readily available copper ill soil. This degree, of sensiticity is enough to determine the presence. of copper anamalous an as and, ecentually, to discouer copper mineralization. Circumstances determine whether it is better to make analyses in the field or in a permanent laboratory. The rubeanic acid test described in this article has been designed primarily for field use: it is simple and virtually foolproof, and it requires a minimum of field kit." It is sensitive, easily de- • Ed. Note: Persons Interested in purchasing kits suitable for rubeanic acid prospecting can obtain information by writing Eldrico Geophysical Sales Ltd., 633 Hornby Street. Vancouver 1, B.C. The University of British Columbia does not produce these kits for sale and has no financial interest in their production tecting 4 ppm of readily extractable copper in a soil. This is by no means a quantitative test, but it is accurate enough to provide a valuable indicator of copper anomalous areas for both prospectors and field geologists. The easiest method for detecting metal deposits that do not produce visible float or stains is to make a simple chemical test for the metal in overlying soil, or in the silt of a stream that may have picked up metal farther upstream. In Brief: Testing for copper may be done easily by shaking a soil sample with strong acetic solution in a small test tube and pouring the mud into a small filter, the tip of which rests upon a strip of reagent paper impregnated with rubeanic acid (di-thio-oxamide). When copper is present—and only when it is—a blue spot develops. The more copper, the darker the spot. If the copper content is merely the small amount present everywhere, there is a pale blue or hardly visible spot; if it is abnormally high, the spot will be dark. There are, of course, intermediate cases where the experienced geochemist cannot tell offhand whether a medium-strength spot represents rich agricultural soil, weak copper mineralization, or distant rich copper mineralization. Reagents and material are inexpensive; the test may be readily done on the spot with a simple kit easy to pack and handle. Anyone interested in general problems of soil sampling as applied to prospecting may refer to an article recently presented to the AIME. In exploration work it is the contrast between the metal content of anomalous and background areas that is important; absolute values become of greater interest when an anomalous area is being investigated in detail. With specific reference to copper, it has been the authors' experience that the amounts of metal extracted from anomalous and normal soils with buffer solutions of decreasing pH show better contrast if an acid reagent is used. This contrast tends to increase with increasing acidity until 3 to 4 pH is reached. Using a short cold attack on unheated soil, it has been found that further increases in acidity do not produce better results, and only increase the hazards involved in carrying strong acids. An acidity of about pH 4 is satisfactory for direct determination of copper by dithizone. But dithizone itself introduces some problems: it must be made up fresh at frequent intervals, and with some soils, notably those with much ferric iron, oxidation mag take place before all the copper has reacted with the dithizone. Rubeanic acid keeps its strength unimpaired for long periods, is unaffected by oxidation, and is practically specific for copper at pH 4. Consequently it seems an ideal reagent to use in prospecting for copper. History and Background: Rubeanic acid (systematic name: dithio-oxamide (SC-NH2) has long been known as a spot test reagent for some heavy metals with which it gives a number of compounds. Only copper and some metals of the platinum family are believed capable of providing any ru-beanate compounds under conditions of moderate

Jan 1, 1959

By M. G. Corson

The iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well-known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 1.5 per cent. silicon (Fig. I). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximurn strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb, per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2..5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 1.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction. Yensen's graphs, as shown in Fig. 1, indicate also a considerable drop in strength and yield point at the same point of 2.65 per cent. Si,

By P. J. Shenon

ENROLLMENT in geological and mining engineering curricula is declining at an accelerated rate despite the greatest need for trained men ever extant in the minerals industry. Industrial and military demand is mounting, but the number of freshmen selecting the mineral field continues to fall. Estimates on the needs of industry range as high as 30,000 new engineers a year. The current deficit is more than 60,000 engineers less than the 350,000 to 450,000 which eventually will be needed. The indisputable fact is that the colleges are turning out fewer and fewer engineers despite the greatest enrollment in colleges and universities ever experienced in the United States. In 1950 a record 52,000 young men stepped out of the confines of ivy covered walls with engineering degrees in their hands. By 1951, however, the number dropped to 41,000 and present enrollment indicates a national graduating class of only 25,000 for 1952. No letup in the drop is forecast. About 19,000 can be looked for in 1953 and 1954 may reach an unhappy 12,000. It becomes clear that something must be done to attract high school graduates to engineering. One immediate possibility could be to make the course burden carried by the engineering student somewhat lighter. The prescribed curriculum in many schools is such that the student takes the path of least resistance, and instead of training for an engineering future, studies for a vocation which will allow him to learn and at the same time get at least a nominal enjoyment out of college life. Review geological and mining curricula of 20 colleges and it will be found that the engineering student is a veritable pack mule compared to a lad taking liberal arts or some other non-technical program of study. The curriculum for geological engineering at one school calls for 202 semester hr, with almost 23 hr carried per semester. Multiply this figure by three hr, the minimum supposedly to be devoted to a credit and you get 69 hr per week. With a bare minimum of 84 hr for sleeping and eating, about two hours a day remain for recreation. However, the load of other schools investigated is about 19 hr. The University of Utah requires 238 quarter hr for graduation with a degree in geological engineering, while requiring only 183 quarter hr for baccalaureate degree from University college, Utah's liberal arts school. It can be stated with a measure of surety that the same proportions exist in other universities. The first step would be for ECPD to review its requirements for mining and geological engineering. It must recognize that mining and geological engineers operate in a specialized field, as do other types of engineers. Although a geological engineer may not design a bridge, as pictured by the ECPD Committee on Engineering Schools, his field of design calls for similar engineering precision, a knowledge of materials, construction methods, economic considerations, and financing. Six schools have been accredited by the ECPD. What is the basis for approval and can the requirements be modified and still be kept in line with the needs of the geological engineer? Course work from school to school varies with the exception of mathematics, chemistry, and physics. Even in those courses the not inconsiderable variation lends dubious creditability to the mean. One accredited school requires 7 1/3 semester hr of chemistry, compared with 24 hr required by another, making an average for the six schools of 17 1 /3 hr. Required credit hr in mechanics ranges from 4 to 18 and in surveying from 2 to 15. Several non-accredited schools require more hr than do the accredited schools in some courses. Why is the engineering student forced to carry such a back-breaking load? The answer is of course fairly obvious. He is irrevocably set apart from the rest of the student body because of the nature of his life's work. He is training for a place in a world where technology is becoming increasingly involved. He must be prepared to do a job now-and not later. Mining and geological engineering require the same essential backgrounds as other engineers, and more. The "more" is a knowledge of mining methods, metallurgy and geology for the mining engineer. The geological engineer must know in addition, mineralogy, petrography, and geophysics. The load is compounded finally by the addition of liberal arts courses. Should anything be done to relieve the situation? Today's engineer must be a whole man, capable of handling the tools of communication and with an understanding of the economics of industry. He must be able to write clear simple English, and he must be man who can think from some other position than bent over a work table. He must be aware of the history of his country and to some extent that of the world. Not all schools share this view. Only two of the accredited schools require history courses. However, five of the non-accredited schools make it mandatory. Four accredited and five of the nonaccredited schools require economics. Courses in mathematics, physics, and chemistry are fundamental in engineer training. The average for the accredited schools could serve as a guide in

Jan 1, 1952

By Robert H. Carpenter

Molybdenite mineralization occurs in the hood zone of the Questa mine aplite-porphyry intrusive, one of the three sil ica-rich intrusive5 occurring along the east-west trending Red River Trench that crosses the northerly trending Sangre de Cristo Mountains in north-central New Mexico. The Trench is located immediately north of the circular Gold Hill positive block between the Red River and Cabresto Creek drainages. The aplite-porphyry bodies intruded a mid-Tertiary volcanic section consisting of lower andesites, overlain by latites and rhyolites. They occur largely in the andesites and were emplaced mainly by metasomatism rather than by sloping. Hydrothermal alteration occurs both as blanket propylitization in the volcanics and sericitization and kaolinization in the porphyries and as halo-type alteration outward from veins and shear zones resulting in strong biotization in the volcanics and sericitization and kaolinization in the aplitic rocks. Mineralization consists of: ( 1) molybdenite- quartz veinlets; (2) banded molybdenite, quartz veins frequently with biotite and potash feldspar along the walls and occasionally with minor lead, zinc, and copper sulfides and with fluorite and carbonates when again reopened; ( 3) high grade molybdenite locally along shear zones; and ( 4) molybdenite paint along joint and fracture surfaces. The mineralization was associated with faulting that resulted from numerous periods of gravity adjustment along the Trench and was controlled by the major shear systems that trend northeast, east-west and north-south to northwest. Molybdenite has been well oxidized in nearsurface exposures to ferrimolybdite and the molybdenum-bearing ferric hydroxide, akaganeite. The oxidation of the abundant pyrite within the veins and shear zones and of the alteration pyrite in the volcanics resulted in a low pH environment under which the acid molybdate ion released by oxidation was fixed either in the ferrimolybdite or the akaganeite molecule in the veins and shear zones or in the soils. Little has been lost in the runoff.

Jan 1, 1968

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By A. A. Bauer, M. S. Farkas, F. A. Rough

An investigation of the d-phase relationships between the uranium-zirconium and uranium-molybdenum systems was conducted. A ternary cut joining U-31.5 at. pct Mo to U-74 at. pct Zr is presented on the basis of differential thermal analysis, metallographic and X-ray diffraction data. HyDothetical isothermal ternary sections, inferred from the determined d-phase relationships, are presented for the uraniztm-zirconium-molybdenum system. A ternary eutectoid, at 454ºC, was found in zirconium-rich alloys. Its composition, based on metallography and electron-beam micro-analysis, is estimated as U-61.7 at. pct Zr-7.1 at. pct Mo. URANIUM binary systems have been studied extensively in the past to supply basic information needed in reactor-fuel development. Alloys of uranium with zirconium, molybdenum, and titanium are of particular interest because, in these binaries, extensive or complete solid solubility between the body-centered-cubic forms of these elements and y uranium exists. In addition, an intermediate phase of limited solid solubility forms in each of these systems by transformation of the high-temperature ?-uranium phase. Previous investigation of the phase relationships existing between the intermediate 6 phases in the uranium-zirconium-titanium and the uranium-molyb- denum-titanium ternaries have already been reported.1,2 The results of an investigation of the phase relationships existing between the 6 phases in the uranium-zirconium-molybdenum system is reported here. The phase equilibria that occur in the solid-state portions of the pertinent binary systems are shown in Fig. 1. Phase nomenclature appearing throughout the report is as shown in these diagrams. The crystal structure of the phases in this system are given in Table I. EXPERIMENTAL PROCEDURES Alloys were cast and fabricated to 1/4-in.-diam rod. Specimens were heat treated and examined by metallographic and X-ray techniques. Thermal-analysis data were obtained.

Jan 1, 1960

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By James Herbert Bartlett

The MANUFACTURE of Iron in the PROVINCE of Quebec. The St. Maurice Forges.—The deposits of iron-ore in the St. Maurice district, in the rear of Three Rivers, were probably known to the Indians and .Jesuits, but it is not till 1667 that any discovery is reported. The affairs of the colony were then in the control of the " West India Company," who amongst other monopolies had a right to all mines and minerals." Specimens of the iron-ore were examined in Quebec. in 1668 by the Sieur la Potardière, who reported unfavorably on them. In 1671, Louis de Buade, Comte de Frontenac, was appointed governor of La Nouvelle France ; and in the original manuscripts relating to his administration some allusion is occasionally found to the St. Maurice iron mines.? In a letter to the Imperial Government, dated 2d November, 1672, he says: "The iron mine of which I have already spoken is of great consequence. I have visited it myself, in order that I may be enabled to give a more accurate account of its nature. I am gratified to learn that another mine has been discovered in Champlain, which is much richer than the Cap de la Madelaine mine, and the ore is in greater

Jan 1, 1886

By Alden Greninger

THE time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are con-sidered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. MOSAIC STRUCTURE For an exact definition of the mosaic structure of metal crystals-if, indeed, one can be found that will hold for all metals-one must await the results of much experimental work in this field. The writer's investiga-tions have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure l.-Large-scale mosaic structure; more specif-ically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few

Jan 1, 1935

By R. R. Boucher, O. J. C. Runnalls

A pronounced thermal effect has been observed on heating or cooling a1wninum-rich Al-U and Al-Pu alloys. From microscopic and X-ray diffractionstudies, the effectl has been attributed to trnsfor)nations in the inlemetallic phases UAl, and PuAl , involuing rearrangement or cluslering of vacancies The transformation obsrved in Al-20 wi oct U alloys occurred near the a Al-UAl4 eutectic tem-perature of 646°C making it difjicult to detect from heating curves. When cooling, howeoer, thermal mad X-ray analyses indicnted that the high-temperati~re phase labeled p UAL, precipitated initially during euitectic solidification. As solidification continued and after an induction period o-f 5 lo 20 tnin the nu-cleatiorz and growth of the low- twmperature phase, a UAl4 produced an euolution of energy which raised the observed alloy temperature by 1° to 2°C. in Al-Pu alloys the transformation occurred at 645°C, 5 deg below the eutectic solidification temperccture. The eslimated latent heat of transformation was 25 +5 cnl per g PuAl,. The high-tetnpevcl-ture forms of UAl, and PuAl, were easily 9-etccined by chill casting Al-U and Al-Pu alloys and on reheating the alloys the trcltzsforrnation to the a phase was sluggish even above 600°C. Separated single cryslals o-f UAl4, joy example, showed no evidence Of transformalion after heating for 16 hr at 620°C. The transformation rates increased yapidly enough with increasing temperature, however, that a a spontaneous liberation of energy lens observed on occasion when bealing cast Al-20 wt pet U to neal- the RECENT phase studies on A1-Pu alloys have indicated that earlier reported equilibrium diagrams should be modified to take account of several poly- morphic transformations in the intermetallic compound PuAl,.' During the course of the latter work an unexpected heat evolution was observed while cooling a solid alloy consisting of a mixture of a aluminum and PuA1,. The evolution occurred at 645°C, y below the a A1-Pu A1, eutectic solidification temperature. Subsequent thermal-analysis experiments with A1-U alloys showed that heat was evolved there also at a temperature nearly coincident with the a A1-UA1, eutectic solidification temperature of 646°. A search of the literature revealed that similar thermal effects had been observed before for both A1-U and A1-Pu but had never been fully explained.2,3 The purpose of the present paper is to describe thermal-analysis and X-ray diffraction experiments which have led to the conclusion that the thermal effects are due to transformations which involve the rearrangement of vacancies in the intermetallic compounds UA1, and PuA1,. EXPERIMENTAL PROCEDURE The A1-U alloys were prepared by heating super-pure aluminum (99.99 pct +) obtained from the Aluminum Co. of Canada in a graphite crucible surrounded by an induction coil. At 1000°C high-purity uranium metal produced by the Eldorado Mining and Refining Co., Ltd. was dropped into the liquid aluminum and was dissolved completely within 15 min. The impurities in the uranium were A1—4 ppm, Ca-4, C-70, Cr-3, Cu-6, Fe-30, Mg-2, Mn-10, Ni-25, Si-25, and Zn-2. The A1-Pu alloys were prepared by reacting plutonium dioxide with liquid aluminum under cryolite (3 NaF . AlF,) for 10 min at 1100°C in graphite crucibles exposed to the air. The plutonium was 99.8 pct pure, containing trace impurities of Ca, Cu, Fe, Pb, Si, and Zn. The liquid alloys were usually poured into water-cooled molds to provide castings of uniform composition from which samples could be cut for heat treatment and thermal-analysis experiments.

Jan 1, 1965

By C. H. Chou, A. Sauveur

The senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallo-graphic planes of the austenite grains.1 To quote: On cooling through the point As, at about 900° C, iron passes from the gamma condition to a new allotropic form generally designated as alpha. This transformation, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain

Jan 1, 1929

By Nicholas Kowall, K. L. Clark

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By K. L. Clark, Nicholas Kowall

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Walter Miller

PETROLEUM refining, like other industries in the United States in 1940, focused much attention on its duties and opportunities in the field of national defense. In counter-distinction to the situation during the World War; the industry is well constituted as LO existing equipment, processes, and capacity together with planned additions to handle any demands that may be made upon it by the defense program needs. Evident throughout was the growing sense of ability to manipulate oil molecules for the production of materials not hitherto considered as being available commercially from petroleum The development and application of catalytically-induced reactions on a broad front is one of the distinguishing characteristics of refining progress during the year.

Jan 1, 1941

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

By James D. McClung, H. J. Gluskoter, M. R. Geer

INTRODUCTION The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1 ) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; or (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Al- though boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams.

Jan 1, 1979

By J. Brett, L. Seigle, L. Castleman, T. Montelbano

Impurity-induced low-temperature recrystallization of cold-worked tungsten was inuestigated with emphasis on the influence of nickel on the reaction. Palladium, nickel, aluminum, manganese, platinum, and iron greatly lower the recrystallization temperature of doped tungsten, which zs normally very high, but the recrystallization temperature of electron-be am zone-refined tungsten wzre is slightly raised by conlacl with nickel. Recrystallization can be induced at low temperature by the presence of solid nickel on the surface of doped tungsten wire, but apparently not by exposure to nickel vapors alone. Approximately 200 ppm of Ni dijjused into 10-mil wires at 1200 from a deposit of nickel on the surface produced total recrystallization, whereas more than 600 ppm of Ni could be absorbed frotn a vapor source without altering the fibrous structure of cold-worked tungsten. Once initiated, nickel-induced recrystallization required a continued source of' nickel for propagation of the recrystallization front. The solubility of nickel in fibrous 10-mil W wire was approximalely 500 ppm at 1150' C, and the activation energy for penetration of the recrystallization front was 52 kcal per mole. In many applications the usefulness of tungsten depends on critical control of its structure. Cold-worked tungsten with the fibrous structure developed by suitable thermo-mechanical treatment has a low, but technologically significant, ductility. It has long been known1 that traces of nickel, and perhaps other metals, are profoundly deleterious in doped tungsten, because they induce recrystallization at low temperature, which produces a brittle, equiaxed grain structure. This effect appears to be an exception to the general observation that recrystallization is impeded and the recrystallization temperature raised by the presence of impurities.2"9 Previous studies7-'' of the annealing and recrystallization of tungsten wire have divided the phenomenon into prior recovery stages, primary recrystallization and secondary recrystallization. The present investigation is concerned principally with primary recrystallization which is defined here as the replacement of the fibrous structure of deformed tungsten by equiaxed grains. The objective of this study was to explore the nickel-induced recrystallization reaction in tungsten and attempt to elucidate its mechanism. As well, an effort to define which other elements give rise to low-temperature-induced recrystallization was carried out. EXPERIMENTAL PROCEDURE The procedure adopted for these experiments was essentially to bring nickel and other elements into diffusive contact with cold-worked tungsten wires. The process of recrystallization was followed as a function of time and temperature by light and electron microscopic observations. First the influence of nickel on the recrystallization temperature of arc-melted, zone-refined, and variously doped tungsten wire was determined by electroplating a deposit of nickel on the surface of the wire and annealing at a variety of temperatures for 3 hr. The chemical analyses of the tungsten wires used in this investigation are given in Table I. The surface of the tungsten wire was etched with Murakami's slution' and approximately 0.005 in, of Ni was deposited from a Watts-type low pH bath14 for the conditions of these experiments. Variations in plating thickness from about 0.001 to 0.005 in. had no discernible influence on the resulting structures. The wires were then annealed in an atmosphere of dry hydrogen to establish the recrystallization temperature. Concurrently, un-plated specimens were annealed to establish the recrystallization characteristics of nickel-free wire. The criterion of recrystallization was that the fibrous structure be completely replaced by equiaxed grains after a 3-hr treatment of temperature. This provided more reproducible results than use of the first recrystallized grain or a fixed proportion of re-crystallized structure as the critical observation. The structures encountered in longitudinal and transverse sections were examined by both light and electron microscopy at magnifications up to X32,000 using parlo-dion-carbon replicas shadowed with platinum for the latter method. Second, the influence of a variety of metals on the recrystallization temperature of 0.010 in. D alumina-silica doped tungsten wire, AW136-64, was determined. The elements were applied by electroplating whenever possible. Alternatively, they were vapor-plated on the tungsten wire and a greater thickness built up by coating with a dispersion of metal powder in nitrocellulose lacquer. Elements not amenable to either of these procedures were merely slurry coated on the tungsten. The recrystallization temperature was determined as above. Third, the nickel-induced recrystallization process in doped wire was studied more closely by electroplating 8 mils of Ni on 65-mil alumina-silica doped tungsten wire, AW153-NS10, and exposing the wire to temperatures of llOO°, 1200°, or 1300°C for various times in a hydrogen atmosphere. A circular recrystallization front, 'Onsisting of equiaxed grains, developed at the periphery Of the coated tungsten wire, and the advance of this front into the fibrous interior was studied. These experiments employed relatively coarse 0.065 in. D wire because the 0.010 in. D wire recrystallized too quickly to permit observation of the pene-

Jan 1, 1969