Search Documents

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase 'fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,' hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.' It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By Roscoe W. Stensrud

Marcona Mining Company operations are located 500 kilometers south of Lima, Peru, on the Pacific Coast, at approximately 15º-22' latitude south and 75º-11' longitude west. The terrain is sandy rolling hills ranging from sea level at the coast and rising sharply (escarpment) to an elevation of 800 meters at the mine area. The climate is arid and windy with a moderate year-round temperature, ideal for a year-round mining operation. San Juan, a new and modern community of 14,000 inhabitants and developed by Marcona, houses the working forces and their families.

Jan 11, 1968

By Arthur Smith

THE Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district-the United Verde and the United Verde Extension-lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., . a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to? the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Wood chute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the . smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. This strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the vicinity of Allen Springs, at the south end of Mingus mountain and all within the boundaries of the Prescott national forest reserve.

Jan 3, 1924

By John Hays Hammond

Discussion of the paper of John Hays Hammond, presented at the Chattanooga meeting, October, 1908, and published in Bi.-Monthly Bulletin., No. 24, November, 1908, pp. 1171 to 117S. PROF. HENRY Louis, Newcastle-upon-Tyne, En j. (communication to the Secretary'`) :-I welcome Mr. Hammond's paper as an. attempt to give definiteness to the best modern professional practice. Such a codification of our professional ethics is urgently needed, seeing how widely the views of mining engineers differ on some of the point-,. raised, for example, I have no hesitation it) performing a class of work, as to which Mr. Hammond seems to entertain some doubts, and, on the other hand, I strongly condemn a practice which he appears to recommend. I have not the least hesitation in making reports for vendors of mining properties, and am constantly doing so; . the best justification for this practice may be found in the fact that such reports have been repeatedly accepted by buyers as giving a correct representation of the facts of the case, which is all that should be demanded from any report. On the other hand, Mr. Hammond advocates that mitring engineers should take payment for their reports tin shares of a company to be floated upon the basis of such reports. I hold that this is ethically wrong, as even the most honest of men is liable to be unconsciously biased under these conditions. Indeed, I go much further, and maintain that a mining engineer who re¬ports or advises upon mining properties should never hold any-mining shares at all, or be himself interested in any mine,' and this has been my consistent practice for many years. A man who holds shares in a mine, and is called upon to report upon a neighboring property or a similar mine, can never be wholly unbiased, and even if lie could be, he would always lay himself open to the suspicion that he was giving a favorable report so as to-enhance the value of the property in which he himself is interested, or an unfavorable report so as to stifle competi-

Jun 1, 1909

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By John Boardman

THE latest metal-mine accident report available for the United States is that of the Bureau of Mines for the calendar year 1919. Quoting from Table 20, p. 53, of that report, we find that there were 468 men killed, 7 permanently totally disabled, 321 permanently partially disabled, 7848 injured seriously (more than 14 days disability), and 23,330 of 1 to 14 days disability. We have no records to show what the average days lost per case of accident is, but the records for the Anaconda Copper Mining Co. show that, leaving out the fatalities and total permanent disabilities, and counting those in which the lost time was one or more days, the actual days lost due to accidents, for the Butte mines and shops for five years, 1917-1921, were as follows: Accident Statistics, Butte Mines and Shops of A. C. M. Co. Rate Shifts Days Lost Year Accidents Total Shifts 10,000 Shifts Days Lost Per Acci-dent 1917 2,661 3,169,720 8.395 26,734 10.05 1918 2,765 3,545,149 7.799 39,199 14.17 1919 1,381 1,853,143 7.452 22,797 16.50 1920 1,376 1,879,410 7.321 20,164 14.65 1921 376 776,461 4.842 8,287 22.03 Total... 8,559 11,223,883 7.625 117,981 13.80 In order to place an economic value. on this loss, we will assume that all the 468 fatalities and the 7 total permanently disabled in the United States were com-pensated for at the rate which applies in the State of Montana, that is, $5000 each, and that the 8169 serious accidents in the United States were compensated for at an average of $70 per case, thus bringing the estimated compensation paid by metal-mining companies in the United States to the enormous total of $2,946,830 for the year 1919. The figure of $70 per case was obtained by dividing the total amount paid by metal-mining companies under Plan No. 1 of the Montana Compensation Law, for the first five years of its operation, by the total number of serious accidents for those years.

Jan 9, 1922

By George Weaton

Two years ago the general features of the St. Joseph Lead Company's zinc-smelting process were described.1 At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtown smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the com-pany's mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; Si02, 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the concen-trate to a calcine of average composition (first 10 months of 1938) : Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; Si02, 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sul-phuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in. by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO2 to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1939

By E. W. Davis

I . OPERATING TESTS 1. CHARACTER OF ORE UNDER INVESTIGATION On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite . The magnetite comprises about 35 per cent. of the rock. Fig.. 1 show's graphically that the tonnage of minus 200-mesh material produced varies directly with the tonnage fed to the mill. There is undoubtedly some limit to this relation, but there seems to be no indication of it at 18 T. per hr. Some of the conclusions drawn from this test are that: (a) The ball-mill is naturally a machine of very large capacity; (b) if it is not possible to deliver a large tonnage of original feed to the mill, a closed circuit should be provided so that the mill may crush its own oversize.

Jan 2, 1919

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InAs and GaAs were measured over the temperature range 400°K to temperatures above the melting points using a di-phenyl ether drop calorimeter. Smoothed values of the thermal properties have been derived and tabulated at even temperature interuals . The heats of fusion of InAs and GaAs were determined as, respectively, 8790 ± 200 and 12,590 ± 300 cal per g-atom at the respective melting points of 1210º ± and 1513º ± 1°K, yielding entropies of fusion of 7.26 * 0.16 and 8.32 ± 0.20 cal perºK per g-atom, respectively. A general discussion of the thermal properties of III-V com-pounds is given. THE low-temperature heat capacities of InAs and GaAs have been determined by Piesbergen.1Using a dynamic temperature modulation technique, Miller2 has determined the heat capacities of the compounds as well as GaSb and Ge between room temperature and 650°K; however, it has been observed that values determined by drop calorimetry for GaSb3 and for germanium4 are consistently about 5 pct lower than Miller's results. Cox and Pool10 report values for the heat content of InAs and GaAs and the heat of fusion of InAs. No value for the heat of fusion of GaAs appears to have been previously reported. This paper reports results of high-temperature heat content investigations of InAs and GaAs measured in the range 400" to above 1500°K employing a diphenyl ether drop calorimeter. These results, together with our previous results on III-Sb compounds3 as well as heat-content measurements5 of solid InP and Gap, are used in a general discussion of these compounds. EXPERIMENTAL PROCEDURES High-purity samples of the compounds, stoichio-metric to ±0.1 at. pct, were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories. The sample preparation, description of the calorimeter, and details of the heat content measurement have been previously described.3 Samples were sealed in evacuated silica capsules and suspended by a Pt-Rh wire in a Pt-wound vertical tube furnace, heated to temperature

Jan 1, 1970

By Robert R. Walden, LaMont West

KENTUCKY'S first acid-grade fluorspar flotation mill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant.

Jan 5, 1954

By J. L. Humphrey

The origin of roof bolting is obscure, but is believed to have begun some 40 years ago in the mines of St. Joseph Lead Co. in southern Missouri. It was not until after World War II, and more particularly after 1949, as a result of the concentrated effort of the USBM, that roof bolting attracted widespread interest. It is estimated that at the end of 1954, 26 pct of all bituminous coal mining in the U. S. was being done under roof bolts. Those mines alone use nearly 2,000,000 roof bolts per month, according to USBM statistics. Uses in metal mines are increasing rapidly, as confidence and knowledge grow. The application has found equal success in other fields, such as tunneling work for dam and waterway construction and right of way maintenance on highways and railroads.

May 1, 1956

By Rogers Wade

THE Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) South of the international boundary and about 7 mi. (11.26 kin.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The

Jan 8, 1919

By William F. Boericke

RESEARCH in the modern refractories laboratory has two practical ends in view-to develop refractory materials for the metallurgist that will meet particular operating difficulties more effectively and to ?manufacture these refractories at a cost sufficiently low to make their use economical to the metallurgist. At the research laboratories of E. J: Lavino and Co., at Plymouth Meeting, Pa., the technical staff, under Dr. Gilbert E. Seil, is giving principal attention. to an. exhaustive investigation of the following factors in refractories:

Jan 1, 1931

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Byron B. Morton

NICKEL-BEARING alloys are associated with petroleum in the fields of exploration, production, and refining. In the first- named field the geologist of today makes use of such instruments as the seismograph, torsion balance, and magnetometer, the selection of proper alloys and metals for the manufacture of which is an important matter. Nickel-bearing alloys are useful for parts that require resistance to corrosion or that must have non-magnetic properties. Where special co- efficient of thermal expansion are de- sired, they are obtained by using alloys high in nickel (20 to 60 per cent), since, by varying the nickel contents, alloys can be obtained ranging fro111 "Invar", with a low expansion between -40 and 175 cleg. F., to those with coefficients of expansion exceeding that of steels. The latter are obtained by additions of chromiurn to the alloys. Alloys containing 50 to 80 per cent of nickel, which possess high magnetic permeability, find application in certain instruments where this property is important.

Jan 1, 1935

By N. S. Stoloff, M. Gensamer

The effects of temperature, grain size, and magnesium content on the strength and ductility of cadmium were studied in the range -269° to 23 °C. A sharp drop in ductility between -140° and -190°C marked a transition in fracture mode from ductile shear to inter gvanular fracture. The addition of up to 15.35 wt pct Mg in solid solution raised the transition temperature, and for two compositions produced basal cleavages. The relatively high ductility of unalloyed cadmium at cryogenic temperatures is attributed to temperature independence of the yield stress and the absence of dislocation locking. ALTHOUGH numerous studies have been made of the mechanical properties of cadmium single crystals,1-5 no comprehensive investigation of deformation and fracture in polycrystalline cadmium has been carried out. This investigation was initiated to determine the mechanisms of deformation and fracture in polycrystalline cadmium, and to attempt to correlate these mechanisms with the behavior of other metals of hexagonal close-packed structure. A second objective of this work was to determine whether the slip systems and mode of fracture of polycrystalline cadmium could be altered by reduction of the axial ratio, which is 1.886, through alloying. Dorn and co-workers' have been able to induce prismatic slip in magnesium through alloying to reduce the axial ratio. Single crystals of cadmium are so highly ductile that glide strains of 400 pct are observed at room temperature, and 80 pct at -269°c.l Failure in every reported case is by necking down and shearing off of the crystal. Cleavage in cadmium single crystals has never been observed. Magnusson and aldwin reported a ductile to brittle transition for polycrystalline cadmium at about —160 C for specimens tested at a strain rate of 0.05 in. per in. per min in tension. However, even at -196° substantial ductility was retained. The transition temperature was strain rate dependent, impact loading at 19,000 in. per in. per min raising the transition temperature to about -85°C while leaving the low temperature ductility unchanged. No information was given on microstructures or fracture mode, nor were stress-strain characteristics reported. In the present investigation, tensile tests were carried out on polycrystalline cadmium and solid solution Cd-Mg alloys to determine flow stresses, work-hardening behavior, fracture strength, and fracture ductility. Variables employed included temperature, alloy content (and c/a ratio), and grain size.Some compression data also have been obtained for comparison purposes. I) EXPERIMENTAL PROCEDURES A) Polycrystalline Cadmium. Two purities of cadmium were employed in this investigation. Cadmium of 99.95 pct purity was supplied by Belmont Smelting and Refining Co. Cadmium of 99.99+ pct purity was supplied by American Smelting and Refining Co. Threaded cylindrical tensile specimens were machined to give approximately a 1/2 in. long straight gage section with a reduced diameter of about 0.110 in. Specimens were heat treated in evacuated pyrex capsules in the range 140" to 290°C to produce desired grain sizes. All specimens were polished in a solution containing 320 g Cr03 and 20 g NaS04 in 1000 cc of H20. Occasionally this solution caused staining of the specimen, in which case a further polish with a solution of one part HN03 and two parts H202 in two parts ethyl alcohol was employed.' Tensile testing was carried out on a screw-driven Instron machine, at a constant rate of crosshead movement, which for most tests was 0.01 in. per in. per min. Load vs time, and therefore load vs total strain, were recorded. Temperatures from -196" to -40°C were obtained by passing nitrogen gas through a copper coil immersed in liquid nitrogen, and then feeding the gas into a jacket around the specimen. Tests at -269°C were carried out in a helium cryostat, at a crosshead rate of 0.1 in. per in. per min, with specimens of 1 in. gage length. Compression specimens were tested in a jig similar to one designed by ilman. The jig was mounted on the under side of the Instron crosshead. Load was transmitted by means of a rod connected to a movable part of the jig at one end, and the load cell at the other end. A downward movement of the crosshead applied a compressive load to the specimen.

Jan 1, 1963

By G. R. M. Del Giudice

A survey of the flotation literature of the past 10 years indicates an increasing use of the microscope as a tool for investigation. Thus, the metallurgical microscope has been used by Tucker and Head;' Taggart, Taylor and Ince;2 Ince,3 and del Giudice4 to examine mineral surfaces that had been subjected to the action of various flotation reagents and to the action of slime pulps. It has also been used by Gaudin, Groh and Henderson;5 Martin;6 Morrow and Griswold;7 and others to examine bakelite briquets of mill products. The microscope with transmitted light, both with bright-field and dark-field illuminations, has been used by Taggart, Taylor and Knoll8 and by Ince9 to observe Brownian motrement and flocculation in flotation pulps. The use of the microscope at low-power magnifications with incident illumination for the examination of mill products has been known for years.10 Finally, del Giudice11 has used a relatively new type of illumination, the Ultropak, for the examinntion of slime-coatings.

Jan 1, 1935

By E. J. Wasp, N. T. Cowper, R. A. Davis, W. F. McDermott

On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this $5 million installation climaxed three years of development, testing, and construction. The mine and concentrator are located approximately 30 miles from the town of Waratah in a rugged semi-mountainous terrain. The open pit mine will produce approximately 5 million long tons a year of crude ore, which is ground in autogenous mills, separated magnetically, thickened and prepared for the pipeline. The 53-mile pipeline transports the 2,250,000 tons of concentrate north to Port Latta. The Port Latta facilities include the receiving, storage and thickening equipment for the slurry as well as filtering, balling and pelletizing equipment to produce the 2,250,000 tons of high grade iron ore pellets. Five vertical shaft furnaces are used for pelletizing.

Jan 1, 1969