Search Documents

By J. Gurland

THE microstructure of sintered carbides consists of particles of metal carbides, such as WC and TiC, embedded in a metallic binder which is usually a cobalt—or nickel-rich solid solution. One of the important factors influencing the strength of the alloys is the degree of dispersion of the carbide particles in the binder matrix. While it is generally accepted

Jan 1, 1960

By Arthur Green

A GROUP of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point sear Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections.

Jan 1, 1936

By R. A. RAGATZ

THE preparation of specimens for microscopic examination from metal articles of relatively large cross-section offers no particular difficulty. It often happens, however, that articles submitted for examination are so thin that specimens satisfactory for microscopic examination can not be successfully pre- pared by the methods commonly employed when working with larger articles. Ordinarily, the preparation of metallographic specimens involves the following operations : (1) cutting the small specimens to be examined out of the larger mass of metal, (2) cleaning and electroplating, (3) mounting to furnish support during the grinding and polishing operations, (4) grinding and polishing to produce a scratch-free surface, (5) etching and drying. All of these operations must be carried out in such a manner that when the specimen is finally examined under the microscope, the structure seen is a true and well-defined representation of the structure that the larger mass of metal possesses at the place where the small specimen was removed. It is important that the deformation involved in cutting out the specimen be as slight as possible, in order that the subsequent grinding and polishing operations will completely eliminate the cold- working effects in the vicinity of the cuts. It is also important that the specimen never be allowed to attain a temperature high enough to alter its structure; the maximum permissible depends on the metal being handled. With some metals, zinc for example, consider- able care must be taken to avoid heating; with other metals, annealed steel -for example, no particular pre- cautions need be observed because there is no tendency for structural change to occur at relatively low temperatures.

Jan 1, 1929

By A. T. Churchman

The deformation modes of rhenium have been identified as those typical of the hexagonal metals, titanium, zirconium, and beryllium whose c/a ratios, in common with rhenium, are less than ideal for close packing. Slip is observed on (1010), (1011), and (0001) planes and twinning on (1121), (1122), and (1012) planes. The very high rate of work hardening is believed to be associated with intersecting partial dislocations on two (1010) systems which can combine to form sessile barriers. If the stacking fault energy is low, as postulated by Seeger, these barriers should be strong and not easily bypassed by cross slipping. Such an explanation could also account for the very small temperature dependence of the yield stress which was observed. RHENIUM is interesting scientifically as a member of the group of high melting point hexagonal metals: titanium, beryllium, and zirconium with a c/a ratio less than that for ideal close packing. Unlike them, however, it work hardens at a very high rate. This rate is greater and continues to a much higher degree of deformation than for nickel, normally considered to have a high rate of work hardening. This paper presents experimental observations on the modes of deformation of rhenium and, by comparison with other hexagonal metals, some speculation on the cause of the high work hardening. MATERIALS Johnson, Matthey rhenium powder of both 99.9 pct and 99.5 pct purity, see Table I, was compacted at 10 tons per sq in., part sintered at 1350°C in vacuo, and finally arc melted in a "gettered" argon atmosphere arc furnace to produce small buttons. Little difference was observed in the as-cast hardness or working down behavior of the two purities suggesting that either silicon and potassium do not have a significant effect on the working properties of rhenium or they were lost during arc melting. SPECIMEN PREPARATION The cast structure was broken up by cold-rolling with inter-stage annealing at 1600o or 1800°C in a vacuum high-frequency furnace using a tungsten susceptor. Strip for tensile testing was taken from two thicknesses of material 0.011 and 0.064 in. The former with intermediate anneals at 1800°C had a grain size of 900 grains per sq mm, while the latter with inter-stage annealing at 1600°C had a grain size of 3600 grains per sq mm. A coarse grain size was obtained by secondary recrystallization in a half button cold-worked by 30 pct reduction. Annealing times of from half an hour to several hours at 2200° to 2600°C in a "gettered" argon atmosphere arc furnace1 resulted in grains of up to 2 mm diam.

Jan 1, 1961

By T. L. Joseph

A DEMAND for specialized knowledge has directed engineering curricula towards competency in some particular field or occupation. Preparation for life in a broad sense of completeness has received little consideration. Ways and means are needed for weaving some of the threads of liberal education into the fabric of engineering education. Any effort to develop a humanistic-social stem of engineering education will depend largely upon the content of the courses and the type of instruction offered. Many of the courses in college curricula are intended to lay a foundation for more advanced courses to be taken later by those. who specialize in some particular field. Students in other fields lack the background necessary to take the advanced courses and have too much detailed information, soon forgotten, forced upon them if they pursue the foundation courses. To develop a humanistic-social stem for engineering education existing catalogue courses selected should follow some general plan aimed towards broad educational objectives. Courses packed with detailed factual information are necessary for the stu-

Jan 1, 1947

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By G. Willard Quick, John R. Freeman

Jan 1, 1930

By Oliver Bololes

UNDER the able leadership of Samuel H. Dolbear, the Committee on Nonmetallic Minerals furnished a program of sixteen papers comprising three sessions. An outstanding accomplishment in technology presented at the first session by Benjamin L. Miller and C. H. Breerwood is the application of flotation to the purification of limestone used in cement manufacture. In place of selective quarrying to provide high-grade raw material, the quarry-run stone is pulverized and treated in froth flotation cells for removal of free silica and mica. Some advantages are cheaper quarrying, more complete utilization of quarry rock, avoidance of purchasing high calcium stone, lower fuel cost and improvement in the finished cement. Paul M. Tyler presented the general subject of milling methods as applied to nonmetal lies. He pointed out the importance of some of the more recent refinements in ore dressing, and urged the need of a wider appreciation of their possibilities. The gypsum industry of Canada was described by L. H. Cole. Crystal growth during the setting process was illustrated by moving pictures. The Coastal Plain and interior salt

Jan 1, 1935

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible' and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale formation) in alloys of silver with 2, 7 5, and 30 per cent of copper The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver' Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail 5,6 The present research confirms this anticipation The oxidation of a series of 20 dilute alloys of silver has been studied metallographically, some types of subscale not encountered among the copper alloys have been found Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation, i e , they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found The probable reasons for this difference in behavior will be discussed presently EXPERIMENTAL PROCEDURE Silver -The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99 993 per cent Ag)* and the purest avail-

Jan 1, 1942

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923

Jan 1, 1961

By HAROLD A. TITCOMB

TOWARD the close of 1925, a British geologist, T. Landell Mills, brought to the notice of .A. Chester Beatty and selection Trust Ltd. certain mineral areas in southern Yugoslavia. Mills' data, which included rough maps and preliminary reports by' a Yugoslav engineer, Jules Draskocy, appeared interesting to Reatty, and early in 1926, I, with three British assistants, proceeded to Serbiaand commenced the investigation of several groups of ancient mine workings. They were found to be extensive and the geological conditions-schists, limestones, and andesitic intrusive-favorable for mineral deposits. At Stan Trg, on the Trepca Concession, five rniles east of Kosovska Mitrovica, an ancient filled adit was found, a shelter-hut erected, and work started in reopening this adit.

Jan 1, 1936

By C. R. Van Hise

PART I.-GENERAL PRINCIPLES. [ ]

Jan 1, 1902

A regular general meeting of the Canadian Mining Institute will be held in Vancouver, B. C., on Nov. 26-28. The Council extends a cordial invitation to all members of the American Institute of Mining and Metallurgical Engineers to attend.

Jan 11, 1919

The following description is based on the film's narrative script: The film opens with a description of the terrain--tens of thousands of yearly snows compressed into glacial ice, stretching further than the eye can see. A single massive frozen cap--1 812 992 km2 (700 thou- sand sq miles) covering most of the land mass of the world's largest island, christened strangely enough--Greenland. Greenlanders comprise more than two-thirds of the 40 thousand Danish subjects who brave the elements in the Arctic Circle. Along the coastal fringe where the Gulf Stream sheds its last vestige of tropical warmth to temper Greenland summers, tiny villages survive In virtual isolation. Jagged fjords and creeping glaciers are barriers to conventional communication. There are no roads through the year-round ice. Yet, when there is wealth in the land, there are people to tame it, harnessing those unrelenting forces of nature if they can building and surviving in spite of them if they must. Near the tiny site of Marmorilik in west Greenland a gathering of men from places more benign came to challenge a sheer, frozen rock named Black Angel Mountain to tap a deposit of lead and zinc ore. As far back as the 19301s, surface investigation showed zinc and lead sulfides in the vicinity. In the mid-60's mountaineering geological examinations were made and deep-hole drilling, directed by Cominco Ltd., of Canada, confirmed the presence of an ore body, 600 m (2000 ft) above the fjord. These findings led to the formation In 1965 of Greenex A/S, a'Danish company with principal offices in Copenhagen. A utilization con- cession, with rigorous safety standards and environmental controls to

Jan 1, 1977

By Harold Vance

EMPLOYERS of engineers have not always been satisfied with the training that young graduates have received in the conventional four-year course. Specifically, employers of petroleum engineers for a number of years have believed that a four-year course does not allow sufficient time for the student to secure a fundamental engineering background plus the fundamentals of petroleum engineering. A group of California employers went so far as to set up a type of curriculum for a petroleum-engineering course, which was based on four years of undergraduate work and one year of graduate work, with most of the petroleum-engineering courses included in the graduate year.

Jan 1, 1944