Search Documents

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By M. E. Kravetz, E. B. Milosavljevic, L. R. Solujic

Gold ores containing high levels of cyanide-leachable copper minerals, such as covellite, chalcocite, bornite, malachite, azurite, and cuprite have traditionally been difficult to treat economically. A novel hydrometallurgical process for efficient treatment of cyanidation effluents obtained by leaching high copper gold ores (or concentrates) based on the use of Cherokee Chemical organo-sulfur reagents (OSR-A, OSR-B and OSR-C) is described. The process may be modified to selectively precipitate silver, or completely recover silver, copper and zinc, as well as regenerate significant amounts of cyanide. For example, data obtained demonstrate that 100 % of silver and zinc, and 98 % of copper were removed from the solution, while 80 % of cyanide was recovered. The treated barren solutions exhibit enhanced gold and silver leaching kinetics compared to the untreated controls.

Jan 1, 2004

By G. Major-Marothy

"INTRODUCTIONA beneficiation plant to upgrade earthy iron ores is being installed by the Iron Ore Company of Canada in Sept-Iles, Quebec.The crude ore for the plant will come from the Knob Lake area, located in Northern Quebec, where mining has been in progress since 1954.Some 170 million tons of ""direct 11 ores have been mined and shipped in the past eighteen years, with an overall silica content of 7 to 8 percent. No beneficiation - except the reduction of the top size to about 2 inches - took place during this period, but extensive research work has been carried out, in order to find a feasible process.Since “washing"", gravity separation, roasting and magnetic separation experiments did not indicate positive enough results, flotation was tried and found to be feasible.The beneficiation complex being installed will consist of grinding, flotation, dewatering - i.e.: thickening, filtering and drying - balling feed preparation, and agglomeration - i.e.: balling and induration.This process will result in a product superior to the ""direct shipping"" ores and will also expand the ore reserves by allowing material with a higher silica content to be utilized.THE OREThe Knob Lake ores are grouped by mineralogical composition and by grade.BLUE ORES, representing roughly two thirds of the reserves, carry their iron content mostly in the form of massive, blue hematite and martite.YELLOW ORES, about one sixth of the reserves, have predominantly hydrated iron oxides as the iron bearing minerals.RED ORES, the other sixth of the reserves, carry the iron mostly in the form of red hematite.The gangue in all ores is mainly quartz, but aluminum oxides and hydroxides are also present, particularly in the red ores."

Jan 1, 1972

By A. Swanson

The Australian coal industry has been subdued in recent years and only a few new plants have been constructed, but the drive for greater efficiency has seen continued technological developments. The paper lists the new plants and major upgrades, plus summarizes technical developments in the areas of dense medium processing, fine coal treatment, froth flotation, dewatering and on-line analysers.

Jan 1, 2001

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970

By P. J. van der Walt

Some 30 years ago exposure to dense-medium separation in South Africa, culminated in the adaptation of the process for the treatment of -0.5 mm fines. The first commercial plant at Greenside Colliery apparently operated for some 18 years. Three further plants followed, including one treating tin ore. It is gratifying to learn, therefore, that there is renewed interest. The objective of making the process easier to operate (?more practical??) is commendable but the cumbersome technical approach could be counter productive. Perhaps a brief outline of the original thinking might be helpful when analysing the problem.

Jan 1, 2003

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By M. Akser, M. Tomas

Six Sigma is a methodology that uses a structured and disciplined approach to improve process performance (higher throughput, better recovery, lower cost, shorter cycle time, etc.). Specially trained people called “black belts” lead and manage Six Sigma projects. Black belts, with assistance from their team, ensure that projects follow the DMAIC (define, measure, analyze, implement and control) process phases. Timely completion of each project, with measurable deliverables, is key to Six Sigma’s significant financial success. Implementation of Six Sigma has been growing in recent years in a wide range of industries. The heavy mineral industry, like many other industries, could benefit from what Six Sigma has to offer. Specific Six Sigma project examples are included from DuPont’s Heavy Mineral Production Plant in Florida.

Jan 1, 2005

By P. J. Lloyd

There are few data on the composition of discard coal in South Africa, and no overall view of the discards for the entire industry. As a result of work on coal qualities in South Africa, a database was established which enabled a good estimate to be made of the composition of the discard from every mine. The data are presented in the form of histograms of ash, volatile matter and fixed carbon content of the 43 million tons of material which were discarded in 1990. The results are discussed in terms of the closeness of the composition of much of the discard material to presently used power station coal. It is concluded that it is mainly developments in equipment, particularly fluidized bed boilers, which inhibit the wider use of discard coal. However, other factors must be noted, including the relatively high sulphur content of the discards, and the fact that even with the most careful storage the material ages and may become unusable after about 15 years.

Jan 1, 2000

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By Johnna Muinonen

"The Thompson Mill processes ores from the Thompson and Birchtree Mines. While the Thompson ore has very little magnesium containing gangue, the Birchtree orebody consists of veins of massive sulphide in a rock matrix that contains a high proportion of magnesium silicate minerals. A significant fraction of the magnesium is floatable, which lead to MgO levels varying from 3-11 wt% in the Birchtree concentrate. The magnesium in the concentrate causes a higher operating temperature in the smelter, reducing furnace life.Birchtree ore represented 20-30% of the mill ore receipts prior to October 2003. Since then the fraction of Birchtree ore has increased to 50%. A reduction of the MgO in concentrate to less than 3% in the total mill concentrate was required to allow safe and economic smelter operation.In October of 2002 a miniplant was set up to simulate the Birchtree plant circuit. Several flow sheet modifications were tested that led to a proposal for a circuit having increased cleaning capacity for the scavenger concentrate and a recleaner on this concentrate. Addition of CMC in rougher cleaner feed was also found to be required. The solution was confirmed through pilot plant testing in the mill in December of 2002. A full-scale installation was designed, engineered, and installed between February and September of 2003 with commissioning in September and October of 2003. Target metallurgy was achieved one week after start-up on slurry to coincide with the Birchtree Mine tonnage increase. This paper highlights the development, design and commissioning stages of the project.The new MgO rejection circuit has successfully allowed the processing of Birchtree ores producing concentrate consistently below 3% MgO. In addition, the new circuit increased overall nickel recovery in the mill.INTRODUCTIONThe Thompson Nickel Belt located approximately 700km north of Winnipeg was discovered in the early 1950’s. Inco first produced nickel from the area in 1960. Over the years the mill has processed several ores from different ore bodies in the area. Currently the Thompson Mill processes two significantly different ores from two mines, Thompson and Birchtree. The Thompson ore is a massive sulphide orebody hosted in schist, containing feldspars, quartz and biotite. Thompson Ore is characterized by high nickel recoveries and clean, low MgO containing concentrates (<2.5% MgO). The Birchtree ore is ultramafic and contains a high percentage of Mg-silicates such as serpentine, chlorite, biotite, amphiboles and talc. Some of these Mg-silicates report to the nickel concentrate and prior to commissioning of the MgO rejection circuit the Birchtree nickel concentrate typically contained 5-8% MgO"

Jan 1, 2006

By N. Sahay

Improvement in work place environment by conventional methods viz., installation of higher capacity fan, fans in parallel operation or booster fan is a risky proposition in many coal mines in India because of difficult geo-mining condition such as shallow depth, multi seam workings having thin parting and inter connected goaves one above the other. The situation is further worsened if the mines have fire affected sealed off area connected to different ventilation circuits. On many occasions circulation of more air quantity by increasing fan pressure have resulted in initiation of spontaneous heating. To address these problems, authors have made some improvement in conventional Dynamic Balancing of Pressure Technique and worked out few ventilation schemes which are aimed for neutralization of pressure differential across sealed off area at the same time having improvement in ventilation in the mine. The excess pressure differential across sealed off area is mainly caused by introduction of higher capacity fan. Similar situation prevailed in one of the mines of Jharia Coalfield, India. The problem was solved by application of the above technique. In this paper, brief description of the technique, the problem in the mine, results of investigation, computer simulation studies of various schemes and methodology adopted for implementation of the technique in the mine have been discussed in some detail. Keywords: Dynamic Balancing of Pressure Technique, Spontaneous heating, Work place environment.

Jan 1, 2003

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By J. B. Dyess

TARNISH films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper .2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen. sulphide in air to form the various oxide-sulphide films studied. The comparative resistances afforded by (1) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of T= MX10 8 2D X 96,494 X 103 (a) where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angström units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values2 of t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003