Search Documents

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By R A. Pax, B Cornish

Increasing the throughput of the MMG Century operation by over 25% from past practice to preserve cash flow close to the end of life of mine has revealed new throughput and load dynamic instabilities in the SAG mill causing significant time averaged loss of production. A twelve microphone array around the SAG mill (Pax, 2014) using the non-contact acoustic measurement methodology (Pax, 2011, 2012) has been used to diagnose the new dynamics. Dynamic acoustic noise signal information allows discrimination of the behaviour of the steel balls and the rock. Determination of mill load, toe and shoulder angles, water holdup, and proxies for mill load are possible.The instability was diagnosed with the help of an abnormality in the liners/lifters of the SAG mill with one row of lifters having a slightly increased in-mill life compared to the rest. The steel shoulder angle is observed to be disturbed cyclically at a rate of precisely one revolution at low throughputs of 750 t/h. However, at throughputs closer to 1100 t/h, the cyclic signal disappears indicating additional dynamics to randomise the repetitive behaviour of the mill charge. The cyclic signal has been used to operate the SAG mill with improved stability at 1100 t/h by adjusting the feed water addition rate.This paper presents and discusses these results and proposes the suggested origin of the extra dynamics. A small consistent aberration of the lifters circumferentially provides a useful detector of stable mill operation and a novel sensor for the dynamics of the internal operation of a SAG mill.CITATION:Pax, R A and Cornish, B, 2015. A novel measurement for the internal operation of a semi-autogenous mill using acoustic sensors – a case study, in Proceedings MetPlant 2015, pp 120–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Van E. Komurka

This paper presents a cost comparison of the driven pile foundations for two large Wisconsin Department of Transportation (?WisDOT?) projects in Milwaukee, Wisconsin: the Marquette Interchange South Leg, and the Canal Street Viaduct. The projects? geology is fairly similar, but their methods/approaches to pile foundation design and installation differ. Although the Marquette Interchange South Leg had deeper poor soils, its pile design was more-cost-effective than the Canal Street Viaduct?s. Potential reasons for cost differences between the projects are identified, and the effect of the different design and construction approaches on economics is discussed.

Jan 1, 2009

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By B Crossley

Self-cleaning fluidised bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. Recent advances in equipment design have increased the scope of application to include indirect heat transfer in slurry environments, including fouling, scaling and viscous slurries. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve heat transfer problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials may be used.

Jan 1, 2004

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007

By D James

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Limited has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the West Coast of the South Island, New Zealand. The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilising spiral, wet magnet, high tension and plate electrostatic separators have been designed to produce ilmenite from the ore. Studies to utilise the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By Alex C. Smith

The National Institute for Occupational Safety and Health (NIOSH) and Northwest Barricade LLC (NWB) conducted a study to evaluate the effectiveness of a novel fire blocking gel for use in underground coal mines to extinguish or to retard the growth of a coal fire. The gel agent was subjected to controlled laboratory testing to assess its ability to delay coal ignition. It was then evaluated to determine if manual fire hose application could be used to apply the agent to mine roofs and ribs to provide a safe egress for mine rescue teams from a fire area. The gel agent was also evaluated in a water sprinkler system to determine its potential for use in conveyor belt fire suppression systems. The agent was then tested in live-fire exercises to examine its effectiveness in retarding and extinguishing a deep-seated coal fire and wood fire. Lastly, the ability of a Mine Rescue Team to quickly and safely apply the gel agent to a mine entry during a simulated mine fire exercise was determined.

Jan 1, 2010

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, thereby lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within 5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3D multi-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2007

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

The design of a mine should aim to optimise the market value by maximising revenues whilst minimising costs. In open pit mining, the nature of the extraction technique translates this objective into the maximum recovery of reserves while minimising waste extraction subject to technical, economical and safety constraints. Since the introduction by Lerchs and Grossman, in 1965, of a model that is now considered a classic in the area, open pit design has reached a level of maturity and acceptance by industry. These models are being used on a regular basis by designers and planners.This paper proposes a new alternative model for open pit design. It is based on genetic algorithms (GA) and exploits a reduction of the number of decision variables of the more traditional techniques. The novel approach provides more flexibility than traditional models; it can also be extended to consider planning problems that traditional open pit design models are not capable of handling. The algorithm has been designed for two dimensional problems and tested in a simple instance. The results obtained in this simple test are encouraging and are a good supporting argument for the development of a GA model capable of handling three-dimensional (3D) instances. The model presented in this paper is just a first step towards a full GA to solve the pit design problem and it is believed that novel tools like the one presented herein could become great allies in tackling challenging problems in open pit design, an illustration of such a challenging problem is presented and discussed.

Dec 6, 2010

By M. Bhandari, D. Norval

The bulk of plain carbon steel is produced through conventional Basic Oxygen or Electric Arc Furnace routes where the development of the AC Ladle Furnace has made it possible to also produce alloy steels. Smaller Ladle Furnaces have limitations such as lower efficiency; high electrode consumption and diminutive yields rendering them uneconomical to operate and making the processing of low carbon steel grades difficult due to carbon pick up. The demand for special steels and alloys with strict specifications is increasing while commodity prices remain competitive. The production of special steels and alloys have specific process control requirements and the development of the induction melting furnace (IMF) has made it possible to produce smaller batches economically. Refining and alloying of the melt in the IMF further enhance the efficiency. The INDUREF furnace offers increased productivity and flexibility through increased thermal efficiency and can be utilised for holding molten metal for further processing such as granulating, atomising, nitriding, alloy additions and desulphurisation of Ferro-alloys and steels. The system utilises a specially engineered ladle which is placed in an induction-heating assembly comprised of a stationary water-cooled copper coil and lamination packs. The addition of equipment for vacuum degassing and decarburisation of steels and alloys is also feasible. Benefits are: ? No electrode consumption or carbon pick-up ? Lower installation, operation and maintenance cost. ? No line-flicker facilitates operation on a weak power grid. ? Good power factor and balanced load ? No skull formation and reduced refractory consumption ? Higher yield of Fe-alloys ? Automatic controlled stirring

Jan 1, 2004

By Sergio N. Monteiro

Natural lignocellulosic fibers are successfully replacing synthetic fibers in many engineering applications. In addition to well-known conventional lignocellulosic fibers, others with promising properties are now being considered. The present work investigated the mechanical and structural characteristics of a relatively high strength fiber, curaua (Ananas erectifolius) from the Amazon region of Brazil. The results obtained from tensile tests confirmed the superior strength while scanning electron microscopy (SEM) analysis displayed features that justify the possibility of using the curaua fiber as an effective reinforcement for polymeric composites.

Jan 1, 2006

By G. Smith

This paper describes the allure of diamonds over time and highlights the magic and mystery of famous diamonds. Consideration is given to the effectiveness of marketing in the diamond industry. It is concluded that diamonds are held as cherished possessions, valued far above their real market price, retained as valued heirlooms, and widely used as a form of highly liquid currency. In order to sustain value, both from an investment and jewellery perspective, demand has been stimulated to keep pace with growing global supply while the illusion that ?diamonds are forever? has been fostered to ensure that most diamonds, once sold, do not re-enter the market.

Jan 1, 2003

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By Jeremy Theys

The Sacramento Regional County Sanitation District (SRCSD) is improving the sewer system in the Natomas area of Sacramento, CA. The Upper Northwest Interceptor (UNWI) system is an ongoing series of tunnel pipeline projects that will provide sewer conveyance for all residents of northeast Sacramento County to the New Natomas Pumping Station, located North of downtown Sacramento, also in the city of Sacramento limits. The New Natomas Pumping Station then carries wastewater flowsto the Sacramento Regional Wastewater Treatment Plant in Elk Grove via the existing Lower Northwest Interceptor. The Joint Venture of Traylor Brothers, inc. and J.F. Shea (TSJV) were awarded the UNWI 1&2 project in late September, 2007. The planned 5.8 km (3.65 mile) construction route for UNWI 1&2 begins at the New Natomas Pump Station and runs north along the East Drainage Canal to the begin-ning of UNWI 3&4 at Bridgecross Drive. UNWI 1&2 includes approximately 5.8 km (19,240 feet) of 3.65 m (144 inch) inside diameter pipe using Earth Pressure Balance Tunneling Methods. The project also includes 16.76 m (55 feet) of 3.04 m (120-inch) diameter interceptor pipeline, twenty three access manholes spaced approximately 305 m (1,000 feet) apart along the alignment, a 2.13 m (84-inch) by 3.65 m (144-inch) transition structure, a 3.65 m (144-inch) by 3.04 m (120-inch) transition structure, and the connection of three existing sanitary sewer lines to the interceptor.