Search Documents

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By Gordon Revey

Over ten million pounds of explosives are used daily to blast rock in mines, quarries and construction projects throughout the United States. Despite the immense volume of explosives used, serious incidents involving the legal use of explosive materials are rare. Unfortunately, when incidents arise they are well publicized, whereas the great majority of blasting projects-even the most challenging ones—quietly occur without incident or public recognition. Although unfair, media coverage focuses on incidents and/or accidents, and as a result skews the public’s perceptions of our industry. These negative perceptions about blasting profoundly effect our work. Most apparent are the community groups who organize to fight blasting work. However, other impacts are more insidious and have long-term effects on our industry. For instance, planning engineers or government agencies often prohibit blasting to avoid the public’s adverse reaction or because of general fear of blasting impacts. Ironically, as regulations and specifications continue to curtail our industry, the net effect is an increase in the cost of rock excavation. As taxpayers, we suffer needlessly by paying more for government funded construction projects. As blasting professionals we are additionally penalized through loss of work.

Jan 1, 2001

By Nicholas J. Grant

It is the purpose of this paper to examine a number of the recent developments in powder metallurgy, being most concerned with those which are yet to prove themselves rather than those which have achieved commercial maturity. Such developments include the production of very much coarser and very much finer powders, down to the near-micron size range. Also considered are activated sintering, direct powder rolling and extrusion (both hot and cold), brazing and welding, hydrides of reactive metals, oxide dispersion strengthened alloys and theoretical evaluations. Introduction T HERE surely can't be very much argument with the fact that powder metallurgy has made large advances on many fronts during the past ten or more years (1). These advances have taken place in raw materials, in processing, in product development and in a better understanding of many of the phenomena which occur in the various steps involved in powder metallurgy. It should be clear, in view of such growth, that it will not be possible to highlight all of the new developments in the present paper. Many of these developments,

Jan 1, 1965

By Fernández H. Carlos

Debido que el subproducto en la etapa de lixiviación de las calcinas de zinc, alcanza un 18% de plomo y 40% de plata en la refinería de Cajamarquilla, es necesario la recuperación de sus elementos valiosos a través de un procedimiento hidrometalúrgico donde se obtengan extracciones en plomo y plata del orden de 85% respectivamente. En este sentido, el texto señala la solubilidad del plomo y la plata en una solución con excesos de iones cloruros y así someter al residuo a una lixiviación ácido clorurante de altas temperaturas y con presencia de un agente oxidante. Una vez obtenida la solución, se divide el plomo y la plata por cementaciones sucesivas con polvo de zinc. Finalmente, se determina la factibilidad del procedimiento para la extracción de los elementos valiosos del residuo y se disminuye los costos de la refinación del zinc.

Nov 8, 1984

This volume constitutes the Survival Subsystem portion of the final report for the Coal Mine Rescue and Survival System (CMR&SS) program, which was conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated June 17, 1970). The program was directed by the Special Systems Department of the Westinghouse Baltimore, Maryland, facility. The basic objectives of the CMR&SS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major sources: the Request for Proposal from the Bureau of Mines1 and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering2 (NAE).

Jan 1, 1971

By Fabio Loyola

La planta de adsorción de carbón de Pampa Larga (CIC_PL) es la principal planta que contribuye a la producción de Yanacocha. Las pérdidas de oro ocurren a partir de la solución gastada que va a la planta de tratamiento de agua y luego se descarga al medio ambiente. Se identificaron dos oportunidades de mejora para lograr un mejor desempeño de la planta. Una oportunidad está relacionada con mejorar la adsorción de oro sobre el carbón en una solución con alto contenido de cobre. La otra oportunidad está relacionada con mejorar el control operativo de la planta de carbón, al usar el manual corporativo de carbón activado, como también aumentar la actividad del carbón y optimizar la cantidad de carbón en los tanques del circuito de adsorción.

Sep 29, 2023

By Y. Luo

A PC based computer model has been developed by the authors for predicting the surface subsidence due to underground coal mining. Its reliability, comprehensiveness and user friendliness demonstrate that it is a good tool for the mine operators, government agencies and scientific researchers alike.

Jan 1, 1989

By Zay Jeffries

AN acute current shortage of copper, with the prospect that conditions may become worse, indicated by Office of Production Management information. Present estimates of copper requirement for defense indicate that nearly all the available metal will be required in the future for this purpose. Severe dislocations are, expected, but the objective is to distribute the copper available for civilian use in such a manner as to minimize these dislocations. The advisory committee on metals and minerals has been asked for a suggestions which may be helpful in meeting this situation.\

Jan 1, 1941

By César Augusto Martín Hilser Vicuña

El "Punto de fluencia” es el contenido de humedad crítico a partir del cual un mineral concentrado sufre “liquefacción”, es decir, libera la humedad como agua libre al ser sometido a las sacudidas propias de una travesía por mar. En esta perspectiva, el presente texto correlaciona la influencia que tiene el proceso de producción de los concentrados en el punto de fluencia a través de los siguientes factores: granulometría, efecto de los reactivos de flotación y la mineralogía. De forma que al conocer los factores que influyen notablemente en el valor de la humedad límite de transporte, se evita los riesgos de que la carga sufra licuefacción durante su transporte por mar.

Sep 14, 2009

By José Robles

En 1922, se instalaron las primeras compresoras de 80 H. P para la obtención de gasolina natural en Brea y Pariñas, a través de la utilización del gas producido en los separadores de baterias de crudo. Sin embargo, esta cifra se elevó a 22, 000 h.p, demandando una red de 5 plantas de compresión-absorción que funcionan en conjunto con una Planta Central de destilación-estabilización y dos estaciones compresoras auxiliares. En este punto, la intención del trabajo es mostrar el proceso de logro de gasolina natural en el Perú, y el sistema de distribución de gas seco, a partir de la conexión con pozos productores, las plantas de compresión-absorción, equipo de compresores y el equipo de enfriamiento general.

Jul 20, 1955

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of Commerce, as of January 1, 1929 there were 413 completed refineries in the United States, with a total daily crude-oil capacity of 3,509,540 barrels. In addition, 14 refineries, with a potential capacity of 99,000 barrels, were being constructed. Of the completed refineries, 341, with a capacity of 3,325,890 barrels, or 95 per cent of the total capacity, were in operation; and 72, with a capacity of 183,650 barrels, or 5 per cent of the total, were shut down. The improved condition of the refining industry in 1928 was indicated in several ways; namely, in an increase in the total capacity of the completed plants, in the opening up of a few plants which were shut down during 1927, in a decrease in the number of plants dismantled, and in an increase in the number of plants under construction. The majority of the refiners have followed a steady expansion program commensurate in most cases with the increase in demand for petroleum products. Obsolete equipment has been dismantled and modern equipment has been installed, with the net result that the total capacity of the completed refineries in the United States has shown a steady increase since January 1, 1918, the date of the first Bureau of Mines survey. Between January 1, 1928, and January 1, 1929, the number of completed plants fell from 423 to 413, but their total capacity increase 259,160 barrels, or 8 per cent. This compares with an increase in runs to stills of domestic and foreign crude petroleum of 10 per cent, and of domestic crude alone of 7 per cent.

Jan 1, 1929

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

The uptake of zinc, lead, and copper by the flora of the Tui Base Mine area near Te Aroha is described.Vegetation and soil samples were taken from two traverses across the Raukaka Lode. Results. after statistical analysis, indicated that Beilschmiedia tawa was a suitable species for biogeochemical prospecting for lead and that SchefJlera digitata was satisfactory for zinc.The tawa showed a negative anomaly for lead over the vein itself but not over the adjacent dispersion halo. It was concluded that lead concentrations greater than 230 p.p.m. in the wood ash of the tawa and zinc concentrationsgreater than 540 p.p.m. in the leaf ash of S. digitata denoted threshold values for anomalous mineralization in the soil beneath. Although both species contained copper, neither indicated a soil anomaly for this element.

Jan 1, 1969

By Willy Contreras, Omar Barrios, Ned Vásquez

Entre los diferentes tipos de riesgos asociados con la minería subterránea, uno de los más críticos son las vibraciones generadas por efecto de las voladuras. En este contexto, las vibraciones por voladura son un riesgo inherentemente ligado con los eventos sísmicos. Por tal motivo, es de suma importancia realizar un estricto control de vibraciones para minimizar el daño al macizo rocoso que a su vez nos permitirá: reducir la sobreexcavación, optimizar los recursos para el sostenimiento de labores, mitigar los riesgos subsecuentes por subsidencia o estallido de rocas y sobre todo la continuidad de la operación minera cuando está cerca a comunidades sensibles a su área de influencia.

Sep 29, 2023

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989

By Tcharllis João da Cunha Demartini

A produção de uma rocha artificial a partir da aglutinação de resíduos finos de mármore dolomítico pela resina epóxi pode ser uma alternativa viável do ponto de vista técnico, econômico e ecológico. O resíduo utilizado é proveniente do desdobramento de mármore dolomítico em teares de lâminas diamantadas e geralmente é descartado. Esta nova aplicação agrega valor ao resíduo, diminuindo o impacto ambiental gerado. O objetivo deste trabalho foi avaliar as propriedades físicas e mecânicas do mármore artificial produzido pela metodologia de vibro compressão à vácuo. Para isso, foram confeccionadas placas rochosas, em equipamento apropriado, com 85% em peso de partículas de resíduo e 15 % de sistema epoxídico DGEBA/TEPAc. As placas foram produzidas com uma pressão de compactação de 0,5 MPa, à temperatura de 90 °C por um período de 20 minutos. Posteriormente, as placas foram caracterizadas pelos ensaios de densidade, absorção de água, porosidade, resistência à flexão, resistência à compressão e microscopia eletrônica de varredura. Obteve-se um mármore artificial produzido pela técnica de vibro compressão a vácuo com absorção de água inferior a 0,06%, uma resistência à flexão de 33,93MPa e uma compressão uniaxial de 96,49MPa, confirmando uma boa adesão entre as partículas de resíduo e a resina epóxi.

Oct 30, 2017

By Vander de Angeli

Em 2014 houve necessidade de substituição precoce de Caixas de refrigeração no Alto Forno devido a vazamentos provocados por defeitos de fundição ocasionando perda de produção. Após análise das falhas no componente, a oficina de fundição da ArcelorMittal Tubarão na busca contínua pela excelência na qualidade de seus produtos, propôs o desenvolvimento de um novo projeto de fundição visando atingimento de nível radiográfico = 3 nas caixas de refrigeração conforme critério de aceitação estabelecido na Norma ASTM E272. Para atingir o objetivo proposto foram inseridos no novo projeto itens para melhorar o processo de alimentação e solidificação do metal. Como resultado o novo projeto apresentou melhora significativa na qualidade do componente do sistema de insuflação de ar do Alto Forno atingindo níveis radiográficos que atendam as exigências da Norma.

Aug 16, 2017

By Natália Cristina Candian Lobato

A indústria siderúrgica gera cerca de 600 quilogramas de resíduos por tonelada de aço bruto produzido. Estes resíduos, conforme estabelecido pela legislação ambiental vigente, devem ter uma destinação final adequada de forma a não acarretar poluição do meio ambiente. Além disso, a preocupação com a sustentabilidade e a escassez de recursos minerais não renováveis tem feito com que as usinas siderúrgicas invistam cada vez mais no desenvolvimento de meios de produção mais econômicos e menos poluidores e na busca de métodos adequados para a reciclagem ou a reutilização dos resíduos gerados, de forma a minimizar a quantidade de resíduos estocados ou destinados a aterros industriais. Neste contexto, destaca-se a escória e a lama de aciaria LD. Assim, este trabalho, avalia as possíveis tecnologias aplicáveis ao gerenciamento ambiental destes resíduos, apontando as tendências e as alternativas tecnológicas para seus tratamentos, de modo a contribuir para o aumento da sustentabilidade deste setor industrial.

Jul 30, 2018

By Jos. R. Guiteras

This paper is one of a series published by the Bureau of Mines on mining and milling methods and costs. It describes operations in the Alma district of Colorado in September 1937, supplemented by some additional data collected in July 1938. ACKNOWLEDGMENTS The author wishes to express his appreciation of the friendly cooperation extended him by the mine operators in the district. The greater part of the information was obtained from mine and mill superintendents to whom individual acknowledgment is made in the text.

Jan 1, 1940