Search Documents

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

This paper reviews rehabilitation, closure, and post-closure management of the Tui, Golden Cross, and Martha Mines, all of which are located in the Waikato Region of New Zealand. There was no requirement for rehabilitation of the Tui mine, which was abandoned in 1973. There was a requirement to rehabilitate the Golden Cross mine. Mining at that site ceased in 1997, and rehabilitation is now well advanced. When first approved, there were some requirements for rehabilitation of the Martha Mine, but when reconsented in 1998, those were extended, and in addition a requirement for post-closure management was included. As a result, a Trust, funded by the mining company, has been established to take long-term responsibility for the site following completion of closure. The different rehabilitation/closure requirements at each of these sites illustrates that we have learnt something from the experiences of the past.

Jan 1, 2003

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

By L.L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By L. L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By R Hoskings

Conceptual studies of the run of mine stockpiling and reclaiming requirements commenced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and compared with the alternatives. Foundations were designed to minimise cleanup effort and to ensure stability of equipment under design wind loading without storm bays. Programmable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

By Christophe Bragard

The Los Angeles Metro Eastside Extension light rail project included a 1.5 mile underground segment, which consisted of twin 18'?10" ID tunnels, bored with two EPB-TBMs. One of the major project challenges after the completion of the bored tunnels was the excavation of six cross passages within alluvial geology below the water table and with low ground cover. Sequential excavation methods were employed and this paper details the design, ground treatment, support measures, and construction methods used to mine these cross passages beneath the congested urban streets of the City of Los Angeles.

Jan 1, 2008

By S. Ndlovu

To investigate the influence of orientation of crystal lattice on the bacterial leaching of pyrite crystals, single crystals of 100, 111 and110 plane orientations were used for the study. Experiments were carried out in the presence of a Thiobacillus ferrooxidans culture. The different corrosion patterns observed on the surfaces of the bioleached samples suggests a variation in cell-surface interaction from one crystal plane to the other. The surface corrosion patterns generally reflected the influence of the symmetrical arrangement of the atomic planes in the lattice on which they formed. The results indicate that the surface properties of mineral sulphides may control the evolution of corrosion patterns and consequently the initial oxidation process in acid bacterial leaching.

Jan 1, 2004

By D. Wolfe, K. Reid, T. Nunn

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. In order to minimize front-end rejects, and to allow for high throughput, the ore top size at Aurora has been set at a nominal 125 mm. These relatively large lumps have a significant effect on both pump performance and pipeline pressure gradient. Current design methods underestimate the solids de-rating effect of lumpy slurries in pumps, and do not accurately describe the distribution or magnitude of the lump effect on pipeline pressure gradient. Data from the Aurora hydrotransport systems has been compiled, to quantify the effect of lumps on the pump head ratio and pipeline pressure gradient, and how this effect changes as lump ablation occurs along the length of the pipeline. A model has been built, using a logarithmic curve, which predicts the effect of 125 mm lumps on pipeline pressure gradient as a function of velocity and the distance from the start of a hydrotransport pipeline. This model is applicable only to Aurora hydrotransport operation, but similar models could be developed for other operations using the same methods. Using accurate pipeline pressure gradients and pump head ratios when designing future hydrotransport pipeline systems will help improve their reliability and operability."

Jan 1, 2014

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By K Palmer

Alluvial platinum was recovered during gold mining operations in Maud Creek, a tributary of the Howard River. Average electron probe analyses give Pt 88.75, Fe 5.27, Ir 0.70, Os 1.06, Pd 0.34, Ru 0.14, Rh 1.29, Cu 1.06. Rare grains of a Pt-Fe-Cu alloy are also present and an unusual feature of all grains is the relatively high rhodium content which finds expression in segregations of rhodium arsenide, cherepanovite. Platinum is found in the Orepuki area of Southland, where it is probably partly derived from the mafic rocks of the Longwood Complex. Rocks of the Rotoroa Complex, similar to those of the Longwood Complex, form bedrock in Maud Creek and are possibly the source of the Howard platinum. Alternatively, it might be derived by glacial transport from the Matakitaki ultramafic block 30 km to the southwest. Origin from the Rotoroa rocks is preferred as, if the Matakitaki rocks are part of the Dun Mountain Ophiolites, they might be expected to contain osmiridium rather than platinum. The ratio Pt:Ir-Os has been widely used to distinguish low Pt:Ir-Os ophiolitic from high Pt:Ir-Os gabbroic assemblages. Mafic complexes such as Longwoods, Darran, Rotoroa, and Riwaka might be expected to show similar high Pt:Ir-Os ratios and be targets for platinum exploration. Detrital platinum examined from the Parapara area, Golden Bay is mainly osmiridium, with rare grains of rutheniridosmine, very similar in composition to that found in concentrates from the Kaniere dredge, West Coast.

Jan 1, 1987

By H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in southern Perú and the northern Chile coastal IOCG belt have emerged as two of the major exploration targets in the Central Andes in the last two decades. These Mesozoic Andean IOCG deposits formed in two mineralisation epochs, the Middle-Late Jurassic (170–150 Ma) and Early Cretaceous (130–110 Ma), with the major Cu-rich IOCG deposits located in the Early Cretaceous mineralisation belt. The early studies in some IOCG centres support a magmtic-hydrothermal model for both Cu-rich IOCG deposits and broadly contemporaneous Cu-poor ‘Kiruna-type’ magnetite deposits. However, recent evidence from field, geochronology, fluid inclusions and stable isotopes show that in the major Central Andean deposits (eg Raúl-Condestable, Mina Justa in southern Perú, La Candelaria-Punta del Cobre and Mantoverde in northern Chile), the incursion of evaporite-sourced basinal brines or sea water may be a prerequisite for economic Cu mineralisation. Moreover, the Cu-poor massive magnetite deposits could be interpreted as a product from iron oxide melt, with minimal intervention by non-magmatic fluids. Therefore, they could represent two contrasted deposit types and contain little genetic relationships. The different roles of magmatism during the Mesozoic are responsible for the variable mineralisation in the Central Andes, including IOCG, magnetite and ‘manto-type’ deposits. The ore modelling for both the Middle-Late Jurassic and Early Cretaceous metallogenic epochs in the Central Andes are reconstructed.CITATION:Chen, H, 2015. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in the Central Andes – a refined IOCG ore-forming model in the Palaeozoic Continental Margin, in Proceedings PACRIM 2015 Congress, pp 251–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K. Hopperstead

Ventilation planning in trackless metal mining is often taken for granted. This paper highlights the trials of planning and executing the ventilation design for Bog Zone at the Lisheen Mine. Ventilation planning for Bog Zone started at the feasibility study stage in 2003; subsequent design changes continued until 2006. In August 2006, the development of the Bog Zone ore body was accelerated through the use of contractors; in addition, the Lisheen equipment fleet was revised based on a larger load and haul fleet. As a result, the circuit was reviewed in terms of changes in design conditions and best practices. This review resulted in a 40% increase of total airflow required to mine Bog Zone. Resources utilized to design the circuit include: external review, computer modeling, and in-house Lisheen planning and operational staff review. The final ventilation design configuration was adopted in 2007, after modeling and evaluating 30 different scenarios, resulting in a better distribution of airflow, optimized secondary escape way, reduced contaminants, and a total power reduction. The value of investment in computer modeling of primary ventilation circuit and planning for staged implementation should never be underestimated.

Jan 1, 2009

By Calvin Konya, Anthony Konya

State and Federal construction specifications require the Blasting Contractor to prepare a Master Blasting Plan which is reviewed by the Owner’s Representative. The Master Blasting Plan requires the Contractor to submit the design of a typical blast. Most blasting specifications also require the Blasting Contractor to submit Daily Blasting Plans. The Master Blasting Plan and the Daily Blasting Plan require that the Blasting Contractor also submit the types and quantities of explosives and initiators used. The specifications also request that the Blasting Contractor submit the pounds of explosive used per delay for both production and presplit blasts. The Blasting Contractor may also be required to predict the anticipated ground vibration and air overpressure levels for the proposed blasts. There are equations that can be used to predict the ground vibration. There are also equations that can be used to predict the air overpressure levels. The data for these equations were primarily derived from quarry and surface coal mine and some construction blasts. Data from major construction projects were analyzed in this study to determine new air overpressure propagation equations for construction blasting. These new prediction equations compare calculated results analyzed from field data with other existing air overpressure prediction equations. Production blasting air overpressure values are also compared to air overpressure from presplitting

Jan 1, 2015

By Xiaoning Yang, C David Pearson, Brian W. Stump

An experimental study of ground motion from explosions designed to remove overburden in an open pit coal mine is reported. The purpose of this study is a characterization of these ground motions in the distance range of several tens of meters to several kilometers. The investigation has focused upon both single cylindrical sources with different explosive configurations as well as arrays of charges in the production mode. Critical to this study of source configuration and coupling is experimental control of the individual explosions, the timing of the explosions and the geological properties. The height of the explosive charges, their depth and charge distribution were monitored in the field. High speed photography as well as velocity of detonation measurements were made on the multiple explosion source so that detonation of individual charges could be documented.

Jan 1, 1994

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By L Torckler, R L. Brathwaite

At Neavesville gold-silver (electrum) mineralisation occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydrothermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz-adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy and sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt per cent NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei and Broadlands. The age of the rhyolitic pyroclastics and related alteration and mineralisation is probably Pliocene and Neavesville therefore represents a fossil geothermal system. The intensely fractured zones containing the gold-silver mineralisation were probably produced by hydraulic fracturing generated by accumulation under pressure of hydrothermal fluid in blind fault zones. Study of fluid inclusions indicates that hydrothermal quartz associated with electrum was deposited under boiling conditions. High grade electrum mineralisation at Graces workings appears to be localised by reaction of hydrothermal fluid with sedimentary marcasite in black shale.

Jan 1, 1980