Search Documents

By Cathy Aimone-Martin, Robert Brentar, Brent Meins, James Lauer

Vibration measurements of multi-story structures in an urban environment began 3 years ago in New York City during close-in blasting to adopt correct measurement procedures and recommend revised ground vibration limits that best characterize cracking potential in mid- to high-rise structures. Two broad categories of structures included non-engineered 4- to 6-story multi-family unreinforced brick masonry buildings, built from the late 1800s to around 1930, and post-WWII, high-rise structures of reinforced concrete and steel rising 12 to 40 stories. In-ground vibration limits similar to those recommended by the U.S. Bureau of Mines safe criteria, developed for 1- and 2-story residential structures, are imposed by the New York City Fire Code. However, these limits are often lowered by project engineers or New York Department of Buildings when blasting is planned near buildings designated Landmark or historic and classified as fragile or vibration-sensitive. Seismograph measurements to determine compliance with in-ground velocity limits currently employ geophones mounted to basement walls and on concrete slabs overlying rock. These measurements cannot be correlated with upper structure cracking potential and are often exceeded, resulting in excessive and costly downtime to allow post-blast damage investigations.

Jan 1, 2014

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By Carl D. Ealy

Work is being done to web enable the FHWA Deep foundation Load Test Database. Originally designed to function in the client server environment via modem, access to the database both for data maintenance and user queries has been upgraded to take advantage of the Internet and current and future information technology innovations. The DFLTD will be part of an Automated Geotechnical Information and Design Aid System, the object of which is to assist those involved with managing and maintaining our nation's highway infrastructure. The system will also meet the needs of university and other research institutions for a statistically meaningful source of high quality data for the development and verification of improved analysis methods, in-situ testing methods, etc.

Jan 1, 2002

By N. Shariatmadari

Two dry docks are currently under construction on the northern banks of the Persian Gulf by Iran Shipyard and Offshore Industries Co. (ISOICO). The construction of these dry docks forms a huge civil offshore project. The foundation system include more than 6500 large diameter (40-48 inch) spiral pipe piles with embedded depth varying from 18 to 25 meters. Extensive geotechnical subsurface investigations were carried out in the project site in order to provide enough information and proper perspective on the underlying soil layers. The results of geotechnical investigation indicated that a 20 m thick dense silty sand layer exist which can be considered as the main bearing stratum. Due to short clear distance between the piles (less than 3 m) refusal occurred for some piles, accordingly led to actual length less than their design length. To verify and in-situ evaluation of piles capacity, static and dynamic full scale loading tests programme were performed. The data from 40 static compression and tension and also 50 dynamic tests with PDA were interpreted and analyzed by current approaches and CAPWAP software. The results of analysis demonstrated that the safety factor of bearing capacity of piles must be increased to reach a safety factor of about 1.8. To achieve this purpose the interaction of combined piled-raft system has been realized.

Jan 1, 2007

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950’s and 60’s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining methods during and after this period led to that pneumatic devices being unable to treat run-of mine coals with the desired efficiency. Since the 1960’s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. This is the last operating dry coal dressing plant existing in Europe. The actual technical standard of dry coal dressing has been analysed during test-work and sampling in this plant (Saar Region in Germany). The process and the advantages and disadvantages are presented. The plants problems are low efficiency in the fine fraction –6 mm and the coarse fraction +30 mm and a low overall throughput as well as the lack of an automatic process control system. The separation results in the medium size fractions between +6 and -30 mm are excellent"

Jan 1, 2003

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By T. C. M. Pillay, John Chipman

The Si-0 equilibrium in liquid iron was investigated in some detail by Gokcen and Chipman1 who reported equilibrium constants of the following reactions: In each case the thermodynamic equilibrium constant K was obtained by extrapolating K' to infinite dilution. Their results on reaction [I] were consistent with those of earlier observers, and there seems to be little doubt as to the approximate validity of the equilibrium product determined. On the other hand, the results on reactions [2] and [3] indicated unusual curvilinear relationships between the activity coefficients of silicon and of oxygen and the silicon concentration. Since a linear relation is observed in all other similar instances, it was concluded that some source of error had affected the gas-metal equilibrium relationships. Recently the authors undertook a restudy of these equilibria with the view especially to establishing the equilibrium constant of reaction [2]. Their experiments, however, were discontinued before a tbroughly satisfactory answer had been obtained and consequently have remained unpublished until the present time. Quite recently Matoba, Gunji, and Kuwana2 published the results of a very thorough study of these equilibria. It is the purpose of the present note to Compare these three sets of experimental data, a comparison which leads to Confirmation of the results of Matoba and coworkers. The experimental arrangements described by Dutilloy and Chipman were employed. A controlled mixture of Hz, H,0, and argon was led into the induction furnace over the surface of the Fe-Si melt contained in a silica crucible. On account of the slow approach to equilibrium, runs were continued for at least 8 hr and, in some cases, as much as 12 hr. Samples were taken by means of silica tubes at the start and during the final 4-hr period of each run. Out of twelve runs only seven appeared to have approached equilibrium with sufficient certainty to be reported here. The results of these experiments, all at 1600°c, are shown by the triangles in Fig. 1. Equilibrium was approached from both oxidizing and reducing conditions and the direction of approach is indicated by the shape of the triangle. Attempts to extend the study to higher silicon concentrations were unsuccessful on account of the transfer of silica from the metal bath to the upper portions of the crucible by means of a silicon-monoxide mechanism. Matoba, Gunji, and Kuwana used similar methods and approached equilibrium from both sides. Their results at three temperatures are shown by the solid lines of Fig. 1. A line corresponding to 1600 deg is interpolated from their equations and is shown by the dotted line. The results of Gokcen and Chipman at 1600 deg in the range 0.02 to 2.0 pct Si are also shown. At concentrations up to about 0.6 pct Si, these investigators approached equilibrium from both directions, and their results in this range appear to be trustworthy. Above 1 pct Si, however, all of their experiments involved oxidation only, as shown by a decrease in the silicon content of the bath. It now seems certain that they failed to reach equilibrium at these higher silicon concentrations and that the curvilinear relation shown by their results is incorrect. It is evident that their results in the lower silicon range are in good agreement with those of Matoba and coworkers. In fact, a straight line drawn through their results would parallel the dotted line and would differ from it by only 0.05 in log K. The new data also lie close to that line. It may thus be concluded that the three sets of data are in good agreement and that the equations proposed by Matoba and coworkers for reaction [2] are satisfactory . They take the limiting value of log K', at 0 pct Si as log K ,. The slope of each line gives the value

Jan 1, 1962

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009

By Steve Kral

The mining industry in northern Ontario is known mostly for its huge nickel deposits. Inco’s and Falconbridge’s nickel mines in the Sudbury Basin are the best known. And with nickel prices being what they are, interest in the region continues. And how. Inco and Falconbridge want to merge. Teck Cominco wants Inco, but without Falconbridge. Xstrata made a hostile bid for Falconbridge, which Falconbridge rejected. And, in June, Phelps Dodge trumped them all when it made an approximately US$40-billion friendly offer for Inco and Falconbridge in a two-part deal.

Jan 1, 2006

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

By Tom Treleaven, Andrew Williams

Several contracts were let in Greenwich, Connecticut, for the installation of a sanitary sewer. The majority of the excavation was in rock and involved numerous challenges due to the following conditions:

Jan 1, 2003

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006

By Youzhen Zhang

The drilling boom is the key component of a roof bolter, and it has significant impact on the performance, safety, and reliability of the overall working device. In this paper, the experimental modal parameters of a drilling boom at low frequencies are identified with the Laplace wavelet correlation filtering method. Based on the obtained experimental parameters, a finite element model of the drilling boom is revised using an optimization algorithm to improve its accuracy. The dynamics of the drilling boom are analyzed through its modal and harmonic response. As a result, an improvement for the drilling boom is proposed to fix the weak links and enhance the dynamic performance.

Jan 1, 2012

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By M. J. Lukhele

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree A number of high wall mining methods were developed over the years to mine coal reserves exposed on the high walls created during surface mining. The auger mining system was initially developed in the early 1940s in the United States of America. High wall mining is a method of recovering coal from seam exposed either by mechanical excavation methods or natural erosions. This is usually associated with strip-mining (opencast) where the stripping ratio is high and uneconomical to mine using the opencast mining method. This paper discusses the surface auger mining as deployed at Rietspruit Mine Services Proprietary Limited.

Jan 1, 2002

Thank you for this opportunity to address your conference on 'The role of coal in the New Zealand energy market'. New Zealand's energy market has, in common with much of New Zealand, undergone major change following the market reforms of the Labour Government. As far as the energy sector is concerned this change has been for the better, as it has created for the first time in a very long time a 'true economic market' for energy in New Zealand. This is in marked contrast to the previous regime where: ò Electricity was state operated, subsidised and cross subsidised. ò Oil was imported and subject to a raft of taxes and duties. ò Coal produced by state mines was priced by cabinet committee, based on other energy prices rather than on the costs of production and delivery of the energy product. Today, with the establishment of the SOE's we have a market of competitive supply, where the customer has the choice of energy with prices based on the true costs of production and delivery. This can only be good for the customer as the cost is now based on the real costs of production, not on political whim. So where does coal fit in this brave new world of free market energy supplies? Well, opportunity, they say, knocks but once.

Jan 1, 1990

By Masanobu Masukawa, Toshio Shiota

The shaft-type ferromanganese smelting furnace (SF) at Mizushima Ferroalloy Co., Ltd. has been in operation since startup in 1985 and is continuing to perform smoothly. Production has been increased from the original design capacity of 270t/d to 350t/d by various operational improvements. As a productivity index of the shaft-type furnace, production of 350t/d is equivalent to productivity of 0.9t/m3/d (daily production/cubic capacity of furnace). Recently, various operational improvements were implemented to achieve productivity of 1.0t/m3/d or higher, including oxygen enrichment operation, increased tapping frequency, maintenance of the throat profile, and operation with small lump coke. The target productivity of 1.0 t/m3/d was achieved in January 2005. This report describes the improvements introduced as part of this high productivity technology.

Jan 1, 2007

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005