Search Documents

By C. L. Brown

"INTRODUCTION The heavy loss of life from mine fires in some coal mines recently has focused attention on the importance of maintaining reliable communication systems between the active working sections of mines and the surface. A study of conditions following disasters in mines indicates that in several instances lives could have been saved if telephone communication had been available. Communication systems were not installed in some of these mines where disasters occurred, and in other mines they were installed in such a manner as to be rendered useless following a mine explosion or fire. Lives have been lost because of the inability of the rescue crews or persons di-recting the rescue to communicate with trapped men. Cases are known where many lives might have been saved had it been possible to give instructions for escaping or for location of barricades.More than 500 major disasters in which 5 or more lives have been lost have occurred in mines in the United States. The total number of lives lost in these disasters has exceeded 13,000. Some of the victims died instantly; but for many it was hours and in some instances days before death occurred. Evidence found in recovery operations following some of the disasters indi¬cates that many died needlessly because of the lack of suitable means of communication between the underground working areas and the surface.A localized gas and dust explosion in a coal mine in 1930 resulted in the death of 82 men; 2 were killed outright by the force of the explosion, 6 by a combination of burns and afterdamp, and 74 by afterdamp. About 140 men escaped or were rescued following the explosion, Of these, 119 escaped with little or no assistance, 2 were rescued promptly following the explosion, and 19 were rescued from behind a barricade. Seven bodies were re-covered from behind an ineffective barricade in another place; subsequent investigation proved that these men might have been guided to a safe location had an effective communication system been available."

Oct 1, 1946

Three complete connector assemblies and ten separate contacts were submitted to a series of tests to establish the connector permissibility and compliance with the Bureau of Mines' research Contract H 0110423. Test Procedure TPC-0100 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the low voltage, medium voltage and high voltage A.C. connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1972

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite with length-to-diameter (L/D) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite) were tested to failure in axial compression to determine to what extent an increase in end constraint increased compressive strength. Adjustable steel rings, mechanically tightened about the ends of test specimens to create a radial prestress of 3,000 or 5,000 psi prior to the application of axial load, increased end constraint more than was possible in previous tests using solid steel rings. (Solid rings, epoxy-bonded to the ends of dogbone specimens, increased compressive strength compared with that of straight specimens without ring constraint.) During the loading cycle, additional end constraint was produced by lateral expansion of the specimens against the rings. The effect of the end constraint was to increase the compressive strength 55 to 58 percent for the shorter pillars of dogbone shape compared with the compressive strength of straight pillars with the same L/D ratios without ring constraint. Most pillars with L/D ratios of less than 2 were made stronger by end constraint. Pillars with an L/D ratio of 3 did not benefit significantly from end constraint. When the results from compression testing of straight specimens of rock in the laboratory are used to design mine pillars in situ, the pillars will be larger than necessary if the horizontal compressive stress is several thousand pounds per square inch greater than that resulting from the weight of the overlying rock alone. The L/D ratio can be increased by a factor of 1.76 for ratios in the range 0.25 to 3 and still provide the same compressive strength. The safety factor applied with straight specimen test results should also be acceptable for use with constrained pillar test results.

Jan 1, 1969

By A. S. Macfarlane

Mineral resource management (MRM) practice has developed in South Africa over the course of the last ten years, with the purpose of integrating previously isolated technical functions into a value chain aligned, process organization, responsible for mine planning and optimization. The implementation of MRM within various companies has met with varying degrees of success, often resulting in incremental improvements in the planning process and, conversely, often becoming the scapegoat for poor delivery on plans and projects. The reason for this has been, amongst others, a lack of a suitable metric to define the success rate of MRM in the business at hand, in terms of its contribution to the bottom line. This paper is the result of extensive research by the author into this subject, which has resulted in the conclusion that economic value added is an appropriate measure that will lead to real optimization and value creation in mining companies, if applied within a new, holistic model

Jan 1, 2006

By L. T. Stanley

A method is described whereby the behavior of the front is approximated when gas is injected into a thick reservoir having reasonably homogeneous properties. The method is applied to the Abqaiq field of Saudi Arabia. The producing member is the Arab-D, a high-permeability calcarenite which has no continuous betlding planes. Field performance indicates the injected gas to be partially miscible with the reservoir oil because gas volume factors experienced are lower than those predicted by the gas law. Eqlrilibril~m calculations confirnz ihis and also show that the volume factor may vary appreciably, depending on the relative quantities of oil and gas in contact in the reservoir; consequently, volutnetric balances are made for the purpose of determining the behavior of the gas volume factor during injection history. The effect of gravity segregation on position and shape of the gas front is approximated by dividing the producing section into three zones vertically and tracing the movement of the average interface in each zone, with counterflow of oil and gas taking place betweell zones behind the front. This results in a gas front that advances more rapidly along the top of [he formation than along the base, producing an "umbrella" effect in cross section that becomes more pronounced as the front progresses. The calculations cover the gas-injection period of Abqaiq field history through 1958, and the position of the gas front is plotted at one-year intervals. Finally, some comparisotls between the calcrlated fronial position and the gas-oil contact as Measured by neutron logs are made. INTRODUCTION Fig. 1 is a structure contour map of the Abqaiq field. For analytical purpcses, the field has been divided into two areas designated A and B, as shown on the map. Gas injection into Area A was begun in early 1954 into two wells located near the crest of the structure on the north-south axis of the anticline. During the period covered by this paper, the average injection rate has been 122 MMscf/D with a maximum sustained rate of 160 MMscf/D. The reservoir pressure has been maintained at 2,450 psig since start of gas injection. The reservoir originally was undersaturated but, prior to pressure maintenance, the pressure was drawn below the bubble point in most of the Area A section, creating an in-place free-gas saturation of 8 per cent at the crest of the structure. The average critical gas saturation is 13 per cent established by laboratcry core tests. That the entire reservoir remained below critical gas saturation prior to gas injection is borne out by the fact that none of the crestal wells have exhibited high gas-oil ratios during production history. The Area A reservoir is a carbonate section about 200-ft thick having average porosity and permeability of the order of 22 per cent and 500 md, respectively. The productive horizon is the Arab-D member of Jurassic age and is encountered at an average depth of

By Jeremy P. Doolan, Leigh B. Neindorf, Geoff W. Capes

The development and use of rock mass classification tools have been a key component for improving stope design over the past 4 years at the Xstrata Zinc George Fisher Mine in northern Queensland, Australia. In 2003, stope extraction data from 3 years of open-stope mining provided an excellent situation to review the assumptions in the feasibility study. Extracted stope profile information, drillhole geotechnical data, underground observations, and oral and written communication were used to develop a thorough stope reconciliation performance database. With-out collecting the back analysis data and presenting the data in a usable format, engineers are left to debate opinion instead of engineered judgment. This can lead to biased and uninformed design parameter choices with the potential to repeat poor design. This paper demonstrates some effective, practical examples of empirical data collection where rock mass classifications tools were developed and used to create improved confidence in predicting stope stability and failure profiles. The work contributed to design changes that resulted in a reduction in stope hangingwall dilution and an increase in head grade while continuing to ramp up production from 2003–2005.

Jan 5, 2007

By R. J. Gunderman

A conventional trailing cable connection box on a continuous mining machine was modified by the addition of two innovative devices. These are a pressure vent to preclude buildup of high pressure due to an explosion in-side the enclosure, and a grommet-type cable entry to simplify and speedup cable entering procedures. The innovative devices were evaluated for eight and one-half months in a working section of an underground coal mine. Laboratory tests before and after the in-mine exposure show no measurable change in the devices. Following the favorable in-mine evaluation, technical performance criteria were defined to serve as the basis of approval for the use of the innovative devices. Additional tests to measure comparable gripping of the cable by asbestos rope, substitution rope materials and by the urethane grommet-type entry were included in this effort. Also, literature for the last 80 years was searched. Comments are provided as to how the innovative devices comply with 30 CFR Part 18.

Jan 1, 1982

By John M. Popovich

Disposing of coal mine waste at the surface has been and continues to be a problem which has yet to be resolved within the coal mining industry. A possible solution to this problem is to return the refuse back into the operating underground mine generating the waste material. It is believed that the approach described will provide an inexpensive and pratical solution to the problem. The designed system is installed and operable at the Millers Cove Energy Company, Inc. property in Lee County, Virginia. This system limits surfact facilities to a minimum size. It incorporates state-of-the-art hydraulic transport and backfilling technology and equipment to systematically backfill areas within the active mine. It maximized the benefits of reducing treatment of coal wasts while it minimizes environmental impacts on groundwater. The system approaches the problem in a manner to maximize benefits and minimize risks. The cost of returning coal waste back underground at the Millers Cove site is estimated at $0.67 per ton of marketable coal (1982 dollars), which is slightly higher than their surface disposal cost of $0.61 per ton of marketable mat (1982 dollars). The underground disposal costs do not include cost savings that should be realized within the preparation plant and treatment facilities at the surface. Preliminary tests of the system were conducted at the surface; funding restrictions prevented an in-mine trial. Efforts should continue to demonstrate the feasibility of solving the problem of refuse disposal. The installed system and plant at Millers Cove should provide the opportunity to test an underground disposal operation. This report contains guidelines to pursue this opportunity.

Jan 1, 1986

By G. R. Smith

Critical and strategic metals are often present in small quantities in low-grade domestic ores. When these ores are leached, the resulting solution usually contains the metals in very dilute quantities. Selective electrowinning from dilute electrolytes was investigated by the Bureau of Mines. A metal deposit containing 84 pct nickel was electrowon from the leach solution of a complex domestic ore bulk flotation concentrate originally containing approximately 2 wt-pct nickel. Key to achieving accelerated deposition rates, in the case of dilute solutions, is the rapid movement of the electrolyte through the electrowinning cell. Pure, synthetic nickel electrolytes were used to establish deposition parameters, and to optimize electrolyte velocity or mass transfer rates. Hydrodynamic and electrodeposition parameters for both the synthetic and leach electrolytes are presented and the experimental research described. Selective electrowinning appears to offer a viable alternative to physical separation methods to obtain separate metal "concentrates" from low-grade ores.

Jan 1, 1983

By R. Blickensderfer

Maintaining an adequate supply of minerals and metals to meet national economic and strategic needs is the overall goal of the Bureau of Mines, U.S. Department of the Interior. One method of achieving this goal is to conserve scarce metals by cladding a plentiful base metal, such as iron, with a scarcer metal. To investigate cladding, a vacuum-rolling mill capable of rolling bimetal specimens at temperatures to 1,300° C in a residual gas pressure of 2 x 10-5 torr was established. Metals that were successfully bonded to iron included stainless steels, chromium, nickel, nickel alloys, copper, and several refractory metals including molybdenum and titanium. The effects of the rolling temperature, reduction in thickness, rolling speed, and residual air pressure on bonding strength and bend ductility of the bimetals were determined. Optimum rolling conditions produced bimetals with bond shear strength essentially equal to that of the iron base metal.

Jan 1, 1980

Workers in underground stone mines have a high fatality rate caused by falls of ground from the mine roof or rib. NIOSH recommendations to reduce ground fall injuries and deaths address baskets, mechanical scalers, mechanical bolters, drill steel changing, personal protective equipment, and training. Description of Exposure An informal National Institute for Occupational Safety and Health (NIOSH) review in 1998 identified approximately 17 new underground limestone operations in vari¬ous stages of planning; as many as 35 new underground stone mines are expected by 2005. Many of these new underground stone mines will employ new or inexperienced workers with minimal knowledge of the hazardous conditions that exist underground. Workers in underground stone mines have a fatality rate nearly 20 times that of workers in the manufacturing sector. Three quarters of the fatalities in underground stone mines are caused by falls of ground from the mine roof or rib (Figure 1) [Statistical Abstract of the United States 1985-1999; MSHA 1983-1999]. During 1983-1999, nonfatal ground falls resulted in 140 injuries, or 15% of all underground, lost time stone mine injuries. These nonfatal ground fall injuries resulted in more than 13,800 lost workdays (one third of all lost workdays). Ground falls generate more disabling injuries and time away from work than any other type of incident. [ ]

Jan 11, 2003

Alluvial gold grades are typically highly erratic. It is very often difficult to establish with confidence the in situ grades of reserve blocks due to the small number of pit or drill hole samples available, and their erratic values. Trends in grade are often obscure. Geostatical methods are inappropriate due to the extreme nugget effect found in alluvial gold field data. Classical statistics appear more suited to such data but require assumptions to be made regarding the nature of the population sampled. Recent developments in computer intensive non-parametric statistical methods provide a new approach to dealing with some of the above problems. These methods avoid making assumptions about the type of population distribution, usually through some kind of re-sampling scheme. The bootstrap procedure involves taking the estimate of interest and synthesising its population of by re-sampling the original data a large number of times (1000+), at random and with replacement. The synthetic population is then used to draw conclusions about the likely behaviour of the true population.

Jan 1, 1985

By Steven Gillgrass

Gerdau Monroe has installed and commissioned the Tallman Supersonic Carbon Injection system (TSCi™) for use in their 135-ton Electric Arc Furnace (EAF) located in Monroe, MI. TSCi™ is an innovative injection system with the primary aim of improving injection carbon delivery to the steel bath by increasing efficiency. It is proven technology with installations at numerous steelmaking facilities all over the world. Results from installation and commissioning of TSCi™ at Gerdau Monroe will be reported as well as on-going trials and optimization efforts. Standard injection systems deliver carbonaceous material from a vessel to the EAF using air where it is injected through a lance pipe or oxy-fuel burner. Using this method, material delivery to the EAF is limited by the pressure and velocity of the transport air. Loss of efficiency can be observed by looking at the quality of the injection carbon stream during operation or by measuring loss on ignition of EAF slag or off-gas system dust. TSCi™ uses a patented design and proprietary technology to improve delivery of carbonaceous material to the EAF. Using this method, savings at Gerdau Monroe were realized by reducing the amount of carbon used in each heat while maintaining or improving upon existing foamy slag practice. As well, significant savings were achieved as a result of reduced FeO content in the slag and improved recovery of iron. Additional savings can be realized by using a smaller mesh material to take advantage of lower material cost and higher injected surface area. Other inherent benefits to improved injection carbon include lower energy and electrode consumption, reduced refractory wear and reduced maintenance cost.

Oct 30, 2017

By P. S. Heyns, M. Heyns

A computer model has been developed of mine hoisting systems in deep South African gold mines. Particular attention was paid to the contribution of different modelling assumptions for the guides and guide-roller assemblies. Objective functions indicative of guide-roller tyre endurance, slipper-plate forces and perceived vibration levels were introduced to quantify dynamic performance. These objective functions were used to compare models. It was found that the choice of guide and guide-roller models did not influence the forces on the guide rollers significantly for typical shaft and conveyance characteristics at typical levels of viscous damping coefficients. The rigid and finite-element guide models gave the same results as those of the effective-stiffness guide model, and while the latter is suitable for simulation for design purposes, the finite-element model should be used for unusual guide geometries

Jun 19, 1905

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent t6 as high as 20.5 per cent by volume. 4 Hydrogen sulphide is probably the most toxic gas associated with natural gas,5 and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. 6 The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. 7 The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphide, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free

Jan 1, 1932

By Graham W. Marks

Recently it was shown the total energy method of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing, this work, the present report deals with analyses for beryllium, zinc, cadmium; and indium. There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved. As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is, associated with zinc and cadmium in zinc ores.

Jan 1, 1948

Significance of Ion Interactions in Flotation in Saline and Brine Solutions

Sep 13, 2010

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920' s and 1930's, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a 'collector' in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

By Adam H. Zimmerman

Introduction Noranda, like similar businesses, is suffering the pain of previously unheard of currency relationships, a cost structure built in better days, and conditions of gross oversupply possible in almost any commodity. Indeed, it does seem like the worst of all possible worlds is out there before us. To understand a Canadian natural resource company, you must know how the country is organized. So far as natural resources are concerned, Canada is not Canada. Canada is 10 provinces and each own the resources situated therein. Thus, the conditions of extraction, exploitation, and operation are all set by the province, while the conditions of trade and currency are set by the Federal government. This means that what may be the rule in Newfoundland may not be the rule in Manitoba or British Columbia. The second thing is that the Canadian currency has been a satellite of the US dollar for a long time. This means that we hold the unenviable and unjustified position of being the country with the second strongest currency in the world. What this has meant to us is what it has meant to an American operator. Since 1980, a pound of copper fetches 214% more for a Chilean than it does for us and a pound of zinc 115% more for a Belgian. From an American point of view, Canada is favored because its dollar is valued at 25% to 30% less than the U.S. However, because of industrial indiscretions in years past, Canada has a locked in labor cost disadvantage that is very hard to cope with. Canada has a unique situation with its labor unions. Many of the unions are, or have been, internationals and therefore gained undue strength in early days. Canada has a third political party of socialist persuasion. It is entirely funded by dues from laor union members. Thus, we have a politicized workforce. And finally, we have a public service that has the right to strike. This had made the public service unions by far the strongest now in Canada. What this means to the mining industry is that there is somebody out there blazing the trail. The unrelenting power of these public service unions probably creates a climate more conducive to excessive wage settlements in industry than would otherwise be the case. Study, Work, and Pray So what do we do when times get tough? In simple terms, we study a lot, we work harder, and we pray a great deal. We study a lot in terms of learning hitherto unknown strengths and weaknesses of our products, processes, and operations. We work hard in the sense that we do everything possible to improve our productivity. And we pray a lot because, so far, anything else we have done has not been enough. Some years ago, Noranda recognized that its principal base and precious metal operations were diminishing. To provide for the future, we should branch out into other resource type operations. These might be countercyclical and also perhaps a little more permanent. For this reason, Noranda entered the potash, aluminum, and forest products businesses. This, of course, was a 'brilliant' strategy that was much applauded in its early days. We built an excellent potash mine, the smallest inte-

Jan 6, 1985

By K. L. Paciorek

The aim of the present study is to determine on a gram per gram basis the toxic products of the thermal oxidative degradations of selected compositions. Four families of materials were investigated under the subject contract namely polyvinyl chloride and neoprene compositions, rigid urethane foams I and woods. Three methods were employed to conduct the thermal oxidative degradations: a sealed system (quiescent environment) I a stagnation burner arrangement (dynamic environment) I and a flow-through apparatus (dynamic I but less severe than stagnation burner conditions). The majority of tests were conducted using the first two systems; only limited experiments were carried out employing the third decomposition procedure. All decomposition was done at temperatures of 370 -4000C I the higher temperature being used in the stagnation burner. It has to be stressed that the nature of the products and the relative product concentration are temperature dependent. Thermogravimetric and differential thermal analyses were performed to supplement and extend the above delineated studies and to explore the feasibility of using these analyses as a method for material differentiation.

Jan 1, 1973