Search Documents

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

When the 2008 Olympic Games begin in Beijing, China is September it will not only mark the end of the journey for the Olympic torch and the thou-sands of participating athletes, but the games will also mark the culmination of a massive amount of construction in the city. On display for the world to see will be 31 new and refurbished venues including the 91,000-seat National Stadium called the ?Bird?s Nest? and the aquatics center, called the Water Cube. What will not be featured as prominently on the television cameras broadcasting the games around the world will be the network of tunnels built beneath the city. But that infrastructure of rail lines will be of critical importance to the games. While preparing to host the world, China added a subway tunnel that will include four stops in the Olympic Park. The 4.4-km (2.7-mile) subway line that runs through the complex of stadiums, gymnasiums and parks began trial operations in June. Prior to the opening of that line, Beijing's No. 5 subway line, which runs through the heart of the city from north to south, opened in October. That 27.6-km (17-mile) line took nearly five years to build and includes 23

Jan 1, 2008

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

Validation and Simulation of Optimised Compressive Crushing Ores and aggregates are used in countless applications all around in the society. The frequent and escalating usage of these natural resources requires efforts aimed at not only making do with what is available, but also undertaking actions to improve the production yield and the processes involved. This strive to improve the performance and efficiency of existing crushers and crushing processes has brought about research concerning optimisation of crushing plants as well as theoretical optimisation of crushing. Previous work shows that different applications and different materials require different compressive crushing in order to accomplish a theoretically optimal size distribution. These optimisation results, obtained by genetic evolutionary algorithms and evaluated with so called fitness functions, convey the theoretically optimal number of compressions and their corresponding compression ratios. Presented in this paper are thus some laboratory crushing tests, which are conducted in order to validate a set of previously optimised crushing sequences. More specifically, interparticle crushing sequences are carried out in a Piston-die testing equipment, where samples are sieved between each compression. The subsequent analysis of these results shows good correlation with model predictions, which combined with a comparative study between presented optimisation results and measured data from a real crusher indicate a significant potential for improvement. However, before redesigning crushers according to what is theoretically optimal, the resulting impact as well as the effects on the outcome of a crushing plant must be examined. Crushing plant simulations using the software PlantDesigner« are consequently performed. Models of existing crushers are altered, resulting in changed particle size distributions from some of the crushers in a crushing plant. Thence, it is concluded that significant gains can be made in terms of capacity, process yield and energy consumption.

Sep 13, 2010

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D. Malovichko

Seismic events and pillar failures observed in two platinum mines in the Rustenburg area, South Africa, were investigated. We studied the sources of approximately 300 largest seismic events recorded in 2009. Moment tensors of these events were estimated from amplitudes and polarities of P- and S-waves. The inverted mechanisms contain isotropic implosive components in many instances. Analyses of uncertainty of the moment tensor solutions confirmed the significance of the implosive component in general. Several documented cases of pillar failure were considered in detail. For each of these a seismic moment tensor was calculated from an elastic stress model assuming an instant removal of a failed pillar. The geometries and magnitudes of the theoretical seismic moment tensors are in agreement with the observed (i.e. inverted from seismic data). The results indicate that either pillar failure or fracturing in the proximity of the reef (within a fraction of the dominant wavelength of seismic waves) are responsible for a significant portion of the large events recorded in these mines.

Jan 1, 2012

By Serge Ouellet

Identification and quantification of cementitious phases in cemented paste backfill (CPB) is difficult due to the fineness of tailings and the low binder content used in the mixture. Techniques such as X-ray diffraction and thermogravimetry were ineffective (mainly due to tailing mineral interference) to identify and quantify hydration products in most works reported in the literature. On the other hand, scanning electron microscopy (SEM) was used in many cases but mainly for qualitative purposes. This paper presents the development of a new approach based on a computer program (SEM-XMAP) that combines X-ray dot mapping images acquired by SEM and generates a coloured image representing the mineralogy and the microstructure of a given CPB specimen. The technique is applied to one CPB sample mixed with blast furnace slag (BFS) and acidic sulphated mixing water sampled in a mine dewatering system. The technique allowed identifying calcic matrix, unhydrated and partially hydrated BFS particles, and sulphated phases.

May 1, 2007

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb-Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb-Zn ore was traced to apH effect. In the pH range, 9.5 to 11.0 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH)2 is suggested, the Fe- + ions being derived from superficial oxidation of pyrite in the ore. IntroductionGalena and sphalerite commonly occur together. A typical procedure, using xanthate collectors, is to float the galena first, at pH - 8, followed by flotation of sphalerite after activation with copper (II) sulphate at pH - 10 (to depress pyrite).Flotation tests following this procedure in an undergraduate laboratory course with a Pb-Zn ore from Polaris failed to achieve consistent selective flotation of galena. Occasionally a considerable amount of sphalerite, even though unactivated with CUSO4, floated. This was traced to accidentally high pH. A systematic study was carried out which revealed that sphalerite floated readily in the pH range 9.5 to 11.0 without activation by CuSO4 This paper describes the results of the study and discusses a possible mechanism of this flotation of sphalerite."

Jan 1, 1987

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson, Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001,000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,411,000 tons under less than 60 feet of cover.

Jan 1, 1966

Map

Jan 1, 1941

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

By J. Gholamnejad

The aim of short-term production scheduling is to decide which blocks of ore and waste to mine in which time period (shift, days, weeks or months) so that several operational and geometrical constraints can be satisfied simultaneously. Since 1960s several mathematical programming approaches were developed for solving production scheduling problems that are based on a combination of various operational research approaches such as linear programming (LP), integer programming (IP), dynamic programming (DP), etc. A number of models have been developed in the past three decades but some models have limited application especially to geometrical mining constraints. One of the geometrical constraints is block accessibility. All blocks must be accessible to mining equipments on the same bench. In this paper a binary integer programming model is developed in order to incorporate block accessibility constraints in an efficient manner. This mathematical model insures that each block has been open and can be loaded and transported easily by shovels and trucks.

Jan 1, 2008

By Hisashi Takahasi, Hironobu Yamazaki

INTRODUCTION The slurry shield method was developed in Japan in 1963 and its experimental tunnelling work was performed in 1965. Although the history of this method is short compared with the conventional shield method in Japan, many companies such as Tekken Construction, Okumura Gumi, Nishimatsu Kensetsu, etc. are engaged at present in developing their own unique system of the slurry shield method. The ground of Japan is generally pervaded with ground water and a large number of districts are covered with soft ground, which is composed of fine sand, silt and clay, etc. Therefore, the conventional shield method has always used compressed air with various kinds of auxiliary methods. However, with this method there have been experienced numerous troubles such as ground settlements, lowering of ground water, oxygen shortage within the tunnel, and so forth. The slurry shield method has been developed with the above background. In recent years remarkable progress has been made from the engineering viewpoint in applying this method to driving various kinds of tunnels such as road tunnels, subways, water supply and sewer tunnels, and other tunnels. Apart from Japan, the slurry shield process using bentonite is carried out in England and Germany. OUTLINE OF SLURRY SHIELD METHOD (1) System of Slurry Shield Method Since the conventional shield method drives tunnels using com-

Jan 1, 1976

By D Kepert, M Absalom, N Nitschke, C Fowers

The discovery of the Nyidinghu Iron Ore Deposit totalling 2.46 Bt of resource continues FortescueÆs highly successful exploration record of discovering multi-billion tonne deposits under cover with little to no surface expression. Since inception in 2003 Fortescue have discovered and delineated the Christmas Creek and Cloudbreak deposits in the Chichester Range totalling 3.38 Bt and 3.25 Bt in the Solomon region. Together with other deposits Fortescues resource portfolio now approximates 10 Bt of hematite - goethite mineralisation.The Nyidinghu deposit is situated on the southern margin of the Fortescue Valley, 35 km south of FortescueÆs Cloudbreak mining operations on the north margin of the valley. Nyidinghu comprises approximately 70 per cent BID martite - goethite mineralisation hosted by the Brockman Iron Formation and 30 per cent CID beneath alluvial outwash of the Weeli Wolli Creek in to the Fortescue Valley. Minor DID mineralisation occurs at the deposit margins.BID mineralisation is strongly controlled by the pre-existing NE/SW trending Weeli Wolli Fault system and bounded to the north by the Poonda Fault. Both fault systems are interpreted to have had a long and complex history commencing pre Ophthalmian Orogeny (ca 2.2 Ga) and remaining intermittently active through the Proterozoic.CID at Nyidinghu is the downstream continuation of the combined Weeli Wolli/Marillana CID palaeochannel system being mined by Rio Tinto and BHP Billiton at Yandicoogina and Yandi, respectively.Exploration commenced in August 2010 with the inaugural resource announcement of 1 Bt being made just six months later. To date over 1700 RC and 85 diamond core holes have been drilled forming the basis for the resource of 2.46 Bt and ongoing feasibility studies. Current exploration activities continue to delineate new mineralisation at Nyidinghu with an ultimate target tonnage of 3 Bt.CITATION:Fowers, C, Kepert, D, Absalom, M and Nitschke, N, 2013. Discovery, geology and structural setting of the Nyidinghu iron ore deposit, Hamersley Province, Western Australia, in Proceedings Iron Ore 2013 , pp 81-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013