Search Documents

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By Brian Garrod

Increasing use of pressurized-face tunnel boring machines in North America has produced a similar increase in the application of precast concrete tunnel linings. Where a pressurized TBM is needed, immediate ground support and ground water pressure resistance is also required. A segmental lining installed within the TBM tail shield provides the only available means of providing such a sealed lining. This paper addresses new developments in North America in lining applications and design. For the purposes of this paper, a precast concrete tunnel lining is defined as a tunnel lining constructed using precast concrete segments that are assembled into a lining ring. The lining rings are connected adjacent to each other to form a tunnel lining. Each segment has a sealing gasket around it so that when the lining is completed, it provides a fully waterproof lining system. The ring is erected within the tail shield of the TBM and the annular gap around the ring is filled with grout as the machine moves forward. The ring is not expanded and normally provides the finished lining of the tunnel with no requirement for a second pass lining. The TBM has a series of hydraulic rams that push on the leading edge of the segmental lining to provide the sole system of forward propulsion for the machine. The rings are tapered, being longer on one side than the other. This allows the rings to be installed either on a curve or in a straight line depending on the rotational position of the rings.

Jan 1, 2008

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Higgins RJ

Environmental investigations have been undertaken by Ok Tedi Mining Limited (OTML) since 1981 when the Ok Tedi Environmental Study was commenced. Environmental monit- oring and management programmes were implemented in 1983. The programmes included water quality monitoring, river flow and sediment monitoring, surveillance of aquatic biological communities and a health and nutrition survey of the local people. These original programmes have continued, and additional programmes of work have been developed and revised to reflect changing operations and the need to focus investigations on specific areas and issues of concern. In April 1990, following the establishment by the Government of Papua New Guinea (PNG) of environmental management criteria for the Fly River system, compliance monitoring programs were introduced. Details of the compliance and additional monitoring programmes undertaken by OTML throughout the Ok Tedi and Fly catchments, including programmes of investigation in the Fly River estuary, Gulf of Papua and Torres Strait, are presented.

Jan 1, 1991

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By Eric Konigsmann

"The Pogo project is located on the Goodpaster River, 38 miles north of Delta Junction in east central Alaska. Sumitomo Metal Mining and Teck Corporation are planning to develop a 2,500 ton per day underground mine and mill at Pogo. A preliminary resource of 5.5 million ounces of gold has been identified in two flat lying lenses. An underground adit has been developed to facilitate underground drilling of the deposit and to provide samples for bench and pilot scale metallurgical testwork.Flowsheet development included the evaluation of several processing options. The final flowsheet selected includes SAGhall mill grinding, gravity concentration with intensive cyanidation and direct electrowinning, sulfide flotation with ultrafine regrinding, and cyanide leaching and CIP gold recovery from the flotation concentrates. Flotation tailings will be filtered for placement in a dry stack storage facility or disposed of as paste backfill underground. All of the CIP tailings will be disposed of underground as paste backfill. A pilot plant was carried out to evaluate the proposed flowsheet described above and to confirm the gravity recovery predictions.Great care was taken in the development of the flowsheet and site layout concepts to mitigate the environmental impact of the proposed operation. An overview of the site water management concepts is presented and the impact of water issues on the process flowsheet is discussed."

Jan 1, 2002

The Mineral Density Separator (MDS) was developed by Mintek to predict mineral separation in a plant, evaluate efficiencies and develop scale-up parameters. This study investigated the influence of particle size on the results of the MDS, the misplacement of material in the MDS and the possibility of replacing heavy liquid float and sink analyses of coal with MDS analyses. Six tests were done with coal of different size ranges. Each MDS layer was subjected to a float-sink analysis whereafter each float fraction was screened to determine the particle size distribution. The results indicated that MDS results represent float-sink analyses when compared to an ash curve. There is some misplacement in the different MDS layers, but this does not seem to influence the results negatively. Keywords Mineral density separator, sink-float analyses, heavy liquid analyses, washability curve

Jan 1, 2006

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By D. Schreuder

Conditions in the South African market relating to atmospheric emission control has changed dramatically over the last 10 years. Companies have become more responsible, environmentally aware, and have to comply to more stringent environmental limits set by legislation. This paper describes briefly the current best available atmospheric pollution abatement technologies relating to particulates, acid gases, NOx, acid mists, aerosols, mercury, dioxins and furans. Mention is also made as to the best practices for product work-up and waste product disposal.

Jan 1, 2006

By Martin J. Pedley

The use of soil nailing has grown steadily in the UK over the last 15 years and it has recently become more popular in the Republic of Ireland. This paper presents three soil nailing temporary works case histories where the technique has been used to support steep excavations in difficult ground conditions. It demonstrates the effectiveness of soil nailing when applied in appropriate conditions. Details of design methods and construction techniques are described and those aspects of soil nailing that will benefit from further study and development are identified.

Jan 1, 2000

By D. M. Wagner, G. Biggs, M. Osmundson, C. J. Twaroski

Potential air emission impacts to federal Class I areas from distant sources are receiving increasing scrutiny by federal land managers (FLMs). This paper provides summary results of the impact analyses conducted for FLMs and PSD permitting of a proposed expansion for a taconite processing facility. Results from air quality increment, acid deposition, mercury deposition, and visibility analyses for Class I areas located 50 to 162 km from the facility showed the project would meet the respective regulatory and guideline values for the specific analyses. During the course of the air quality analyses, potential new requirements from the FLMs’ Air Quality Related Values Workgroup (FLAG) efforts and USEPA’s Regional Haze Program were brought into the PSD discussions. The implications for these future guidelines and regulations as they may affect future expansions at other mineral processing facilities are also discussed.

Jan 1, 2001

By Manuel Caro

El presente trabajo describe el proceso de mantenimiento del equipo de aire denominado Optiair. Este filtro al tener una mayor capacidad de retención de polvo, permite que el equipo pueda trabajar por periodos más largos sin tener que detenerse para realizar el cambio de filtros, lo cual incrementa el factor de disponibilidad del equipo. Entre los beneficios principales tenemos: el incremento de salida de aire, menor restricción del flujo, menor caída de presión y una mayor cantidad de contaminante capturado.

Aug 25, 2002

By Wilton Pacheco de Araújo

A siderurgia gera grandes volumes de escória de aciaria como coproduto e precisa incrementar o aproveitamento desse material em novos processos para evitar a disposição em aterros, aumentando a competitividade do setor. Este estudo tem como objetivo caracterizar a escória de aciaria LD da Usiminas em Ipatinga-MG, buscando avaliar o seu potencial para uso como corretivo agrícola e fonte de nutrientes para agricultura. Foram utilizadas técnicas analíticas tradicionais e microscopia para determinar suas principais características. Os resultados mostraram que uma etapa a mais de separação por peneira (2 mm) no processo rotineiro de remoção de metálicos é possível produzir um produto com características químicas e granulométricas estáveis para se constituir um corretivo agrícola comercial. O material apresenta características superiores aos corretivos tradicionais, pois além de corrigir o pH, fornece nutrientes importantes para a agricultura. O processo mais lento de hidratação dos silicatos e de liberação dos nutrientes pode ser interessante para o fornecimento progressivo desses compostos dando longevidade ao corretivo, reduzindo potencialmente o custo de aplicação.

Aug 16, 2017

By G. Papachristodoulou, O. Trass

"Performance data for both wet and dry grinding of materials have been obtained in this novel, planetary ring-roller mill over wide ranges or operating conditions. The Szego mill consists of a stationary cylindrical shell inside which grooved, radially mobile rollers rotate, driven by a central shaft. The mill has several internal design variables such as number, diameter and length of rollers as well as size, shape and pitch oi helical grooves. It is compact, has a high specific capacity, modest power consumption, and can grind many materials down to ultrafine powders. Illustrative data on product fineness and mill power consumption are given along with results from studies on grinding kinetics.INTRODUCTIONThe extensive use and importance of grinding as a unit operation, coupled with the rather low energy efficiency of conventional equipment provide a challenging incentive to investigate novel methods of comminution. Yet, most current development work is taking place in mill performance modelling and optimization, or with various detailed improvements rather than in the field of new equipment development.This paper is a report on the development of a ring-roller mill invented by the late L.L. Szego which embodies several novel concepts. The mill has a broad range of applications, may be operated wet or dry, and can grind materials down to ultrafine sizes with modest energy consumption. It has been developed by General Comminution Inc. in close cooperation with the University of Toronto."

Jan 1, 1986

By John P. Davis

The use of conventional, circulatory air rotary and fluid rotary, cased and uncased drilling methods in the vicinity of sensitive infrastructure can have deleterious effects on the ground conditions surrounding and supporting structures and the structure itself. Furthermore, the use of these conventional methods offers the engineer or contractor little information about the condition of the subsurface during geotechnical applications. Conversely, sonic drilling measurements and samples can be used to evaluate actual conditions during the progress of exploration and construction across a given site. This paper will discuss the history and properties of sonic drilling and explore case histories of geotechnical applications for the advancement of boreholes within vulnerable structures and on sensitive sites for several recent infrastructure projects ? a tunnel and railroad project, a dam grout curtain project, a bridge micropile exploration project and a tunnel instrumentation project. Project summaries will discuss the advantages realized when the application of sonic drilling techniques demonstrated superior accuracy, quality control, efficiency, productivity, penetrability, waste minimization and adaptability when drilling adjacent to or within existing infrastructure. Finally, the discussion will address the current testing and application of sonic drilling to the installation of micropiles, earth retention anchors, grout injection and instrumentation installation where the quality control benefits provided by the inherent soil cores, measurement while drilling systems, accuracy and non-destructive production drilling features will be advantageous.

Jan 1, 2006

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.' This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By Oliver Finn

Gold dredging has made such rapid strides of late and there is such a widespread interest in this branch of mining that I venture to contribute a detailed account of the way in which a Keystone driller was used by me in California to loosen, by blasting, a very tight gravel deposit, preparatory to dredging. There is a great difference between “cemented gravel” and “tight gravel.” A truly cemented gravel is not a dredging proposition, while the tightest possible gravel, where there is no cement, can be made easy working by the following method of blasting:

Jan 1, 2008