Search Documents

By S. E. Khalafalla

In support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has investigated a novel hydrometallurgical system with sulfur dioxide. Differential leaching with dissolved SO2 of manganese, nickel, and cobalt from their hydrous oxides was found to be very rapid and efficient--almost instantaneous and quantitative. In this method a given weight of mixed oxides previously ground to minus 200-mesh is slurried with a leach solution containing a specified quantity of dissolved SO2 for 10 minutes at room temperature and ambient pressure. An empirical leaching parameter, R, is defined as the ratio of the number of SO2 moles in the leaching solution to the weight of the metal oxide charge. Plots of the variation of metal extraction with the ratio R generate a series of sigmoidal-shaped curves, each of which is characteristic of a specific metal extraction. A threshold value of R is required to initiate the leaching of a given metal from the mixed oxides. Once this threshold is reached, the metal recovery can increase to more than 95 pct in very short times. For increasing values of R, the extractability of various metals by SO2 follows the order: Mn > Ni > Co >> Fe, Al, Cu. Differences in the threshold R values permit a variety of metal separations to be made simply by adjusting the quantity of SO2 in the contacting solution. Success in this leaching system depends upon comminuting the sea nodules to less than 0.149 mm (100-mesh). Above this critical size, leaching is slowed due to the inaccessibility of inner particle reacting groups to the SO2 leaching agent. This results in nonselective extraction and less extraction of preferred metal values. At or below 0.149 mm, leaching by SO, is possible with all its attributes of selectivity, sensitivity, and rapidity. Leaching with HC1 solutions of the same pH level as dissolved SO2 yielded mixed, slow, and incomplete metal extractions. This observation rules out any interpretation based on hydrogen ion as the leaching agent. The leaching curves resemble the complexometric titration curves of heavy metals with specific coordination species.

Jan 1, 1981

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013

By R. G. Knickerbocker, T. E. Evans, J. L. Morning, D. R. Torgeson, F. W. Wessel

"INTRODUCTION Pilot-plant studies on processes for converting low-grade domestic manganese ore to high-grade oxide or sulfide products by pyrometailurgical process was initiated at the Boulder City, Nev., Experiment Station in 1942. These investigations were given impetus by the possibility of a national shortage of ferro-grade manganese oxide for war needs.The manganese ore employed-in most of the pilot-plant smelting tests was from the manganosiderite-nodule deposits at Chamberlain, S. Dak. This deposit although low-grade, is extensive and represents, the largest reserve of manganese in continental United States. 6/ The Bureau of Mines has recently developed a Carryall mining-conical rolls treatment method that shows promise of making possible economic removal and subsequent beneficiation of the nodule-bearing shales. 7/ Smelting tests were made also on Artillery Peak, Ariz., mill concentrates in the productions of unrefined manganese matte for the steel The pilot-plant smelting program was based upon the fundamental fact that manganese, like copper, will sulfidize and become miscible with FeS. The matte this formed represents the initial smelting step in the pyrometallurgical treatment of the beneficiated ore. The concentrated nodules containing about. 18 percent manganese were smelted with varying amounts of pyrites and appropriate fluxes to produce Mns-FeS mattes containing 16 to 50 percent manganese. When the manganese and iron was completely sulfidized, the mattes contained 16 to 23 percent manganese. Reducing the pyrite resulted, of course, in the selective sulfidization of manganese and the production of a matte containing a correspondingly higher ratio of MnS to FeS. Complete sulfidization smelting produced slags of lower manganese content and hence resulted in higher manganese recoveries in the matte."

Sep 1, 1946

By Wade Edward Speer

The Hiddenite District of Alexander County, NC has produced some of the world?s finest large emeralds since the first one was discovered 134 years ago. In fact, North America?s largest emeralds come from the district, making this one of the continent?s most unique gem deposits. In addition to emeralds, the Hiddenite District is also famous as the discovery site for the rare spodumene mineral hiddenite, first identified in 1881. Nowhere else in the world do these two minerals naturally occur together. The emeralds are a unique color variety of beryl (Al2Be3Si6O18) with trace amounts of Cr+3 and V+3 substituting for Al+3. The hiddenite (LiAlSi2O6) crystals also exhibit emerald green color due to traces of chromium. Consisting of three large deposits and numerous prospects, the district encompasses an area of 10 km2 (4 sq miles) centered on the small town of Hiddenite. Operations at the Adams, Ellis and North American Emerald Mines properties have been productive at irregular intervals since the 1880s. Currently, only the North American Emerald Mines property is being mined on a regular basis. Recent activity there has exposed a 3-hm2 (7.4-acre) pit with depths of 25 m (82 ft) that provides the best exposures of unweathered bedrock seen in the district in more than 120 years. Although no official records exist, public and private data indicate that the production of the entire Hiddenite District from 1880 to 2007 is about 70,000 carats of emerald and 20,000 carats of hiddenite. The bulk of the emeralds came from the North American Emerald Mine property (NAEM, formerly known as the Rist Mine) where sustained mining replaced the previous sporadic prospecting in 2000.

Jan 1, 2009

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

By David A. Monaghan

On January 14, 1974 a fire occurred in the 3 East mains of the Joanne Mine of Eastern Associated Coal Corp. in Rachel, West Virginia. The mine was evacuated without injury and sealed completely at the surface within 24 hours. It was decided by the coal company along with the U, S, Bureau of Mines, the West Virginia Bureau of Mints and MESA that remote sealing of the fire zone would be attempted. This report summarizes the remote sealing effort and those activities directly related to the remote sealing effort. This chapter provides a brief history of previous remote sealing attempts, a description of the recently developed remote sealing system and a description of the Joanne Mine operation as it related to and affected the remote sealing effort.

Jan 1, 1975

By Sam Kangwa, Thomson Sinkala

In the mining industry, drilling accuracy has a significant effect on the economy of operations. In this paper, results from the Nkana Division of the former Zambia Consolidated Copper Mines are presented. For the stope investigated, it was found that the extra operational costs alone were 462% of the planned costs! Clearly, there is more than good reason to pay attention to drilling of good quality holes.

Jan 1, 2004

By Christian Flores

El proceso que se enfrentó en Tambomayo tuvo su principal complejidad en llevar un proyecto en etapa de exploración hacia la construcción de una a unidad productiva la cual permita obtener resultados económicos y trabajar con altos estándares operacionales en el que prime la seguridad y un buen clima laboral, acompañado al hecho de que la empresa cuenta con una cultura operativa tradicional, lo que género que las principales dificultades para la toma de decisiones es que se tengan que ir derrumbando paradigmas operacionales y de esta manera ser un agente de cambio para el logro de los objetivos.

Sep 1, 2017

By Herrmann Flor

In steelmaking process, where up to 70% of variable cost of finished product is already incurred, energy and refractory costs account for 45-50% of the cost of production of crude steel and contribute significantly to the carbon footprint of the end product. Any attempt to control and reduce these costs will automatically lead to more competiveness and reduced carbon emissions. Leading the technology for ECOPLANT (characterized by the fact that the economic and ecological benefits are integral part of our products), SMS has developed innovative solutions which can be applied to both new and existing plants alike. This paper reviews one of the electrical and automation concepts. Tackling the secondary gas cleaning system and hence being applicable to almost all steel plants, the X-Pact® Gas Cleaning Assistant optimizes the control of individual dampers based on modelling of fluid resistances of ductwork in gas cleaning system. It guarantees the best dust removal from work place at minimum energy consumption.

Oct 30, 2017

By Clarke DS

The igneous intrusions in SE Papua New Guinea are part of a sub-volcanic to plutonic, high-K calc-alkaline to shoshonitic suite. High-K andesitic to dacitic intrusives on Misima and Woodlark Islands, and shoshonitic intrusives in Milne Bay and the eastern Owen Stanley Ranges are related to late Cenozoic andesitic volcanism. Both suites are associated with epithermal Au-Ag deposits and weak porphyry Cu-Au mineralisation. All significant alluvial and lode gold occurrences in the region are spatially related to intrusions. Intrusions in the D'Entrecasteaux Islands and near Mt Suckling are core plutons related to basement doming, and appear to have no association with either volcanism or hydrothermal mineralisation. The core plutons are not petrochemi:ally distinct from the volcano-re:-ed Intrusions.

Jan 1, 1991

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

A short account is given of the theory and practice of determining the true U3O8 content of ore samples by the determination of the beta and gamma activities separately, using the method of Eichholz and his associates.It is shown that, despite the variation of sample activity without change in U3O8 content, the true U3O8 value can still be found.Thorium can be determined simultaneously if this element is also present.

Jan 1, 1957

By Philip Dubbeling

Conventional dynamic sheetpiling techniques are ill-suited to urban development because of the emission of excessive noise and ground vibrations. Drilled shafts and slurry walls alleviate some of these environmental concerns but add additional problems due to large bulky machines, reliance on dusty concrete plants and urban trucking grief. To solve these problems, pre-fabricated sheetpiles are hydraulically jacked-in by reaction principle using a compact and lightweight press-in machine, a so called the "Silent Piler". Through scientific analysis, definition and systemization of press-in machines and methods, new construction concepts such as the one-step approach, implant structures, functional design and life cycle design have been developed to comply with new basic construction principles.

Jan 1, 2006

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the three-dimensional surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. In this paper, the authors discuss the signal processing techniques used to study these relationships, as well as the related implications for mining.

Jan 1, 2008

By K D. Wilkes

The WEMCO Heavy Media Drum Separator was first introduced by WEMCO in California in the 1940`s, initially from their base in San Francisco and later when the company moved to Sacramento. The WEMCO Company became a part of EIMCO Process Equipment in 1985, and in 2002 EIMCO became a part of the GL&V Group when Dorr-Oliver EIMCO was created. Throughout this period of time the WEMCO Drum has been installed on a variety of different applications and is now operating at the heart of many of the world?s largest Minerals and Coal Processing Plants, as well as being used by many smaller producers and metal re-cycling operations. This paper looks at the practical aspects of using WEMCO Drums in a representative range of processing applications.

Jan 1, 2006

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996