Search Documents

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

Copper ores are widespread through the Lachlan Geosyncline in New South Wales, but the size of the orebodies is generally small. The largest deposits occur in the Cobar district where an iron-rich copper ore type has been developed in Silurian sediments. Similar de- . posits to the south in the Nymagee-Mt. Hope-Melrose districts are related to quartz feldspar porphyries of probable Upper Silurian age. Deposits to the east in the Tottenham-Girilambone districts are less complex mineralogically and are possibly related to an ultra-basic source.Copper mineralization in the Highlands further to the east is often developed in Ordovician andesite or MiddleUpper Silurian acid volcanic sequences. The deposits in andesite contain considerably less galena than those in the acid extrusives; a small proportion of the mineralization in the latter has texture, mineralogy, and geologic setting analogous to the Captain's Flat copper-Iead-zinc deposit, for which both syngenetic and epigenetic origins have been proposed. Very little copper mineralization occurs within granitic material, even though rocks of this type ranging from Silurian to Carboniferous in age crop out through much of the geosyncline, and the extent of the metal contribution from plutons to the deposits in volcanics is open to question. Numerous deposits are known in the contact zone around Mid-Devonian and Mid-Carboniferous granites, however, and the formation of these orebodies has undoubtedly been influenced by plutonic activity. Small occurrences of copper with associated minor nickel sulphides are developed in a narrow serpentinite belt of possible Lower-Middle Devonian age in the southern section of the Highlands.

Jan 1, 1970

By Brown A

An experimental evaluation of a selective agglomeration process in which an agglomerated coal rich phase was produced as a result of mixing light oil to various raw coal slurries is described. The beneficiation achieved by this method is compared to that obtained bv conventional froth flotation. The results suggest' that oil agglomeration is a more selective process than froth flotation and is less sensitive to variations in feed pulp density. Selective agglomeration has the additional advantage of producing a low moisture content product. The effect of replacing flotation filter cake with an equivalent amount of selectively agglomerated product in coke-making was studied with the aid of a pilot-scale coke oven. The results suggest that the principal effect of such a measure is to increase the bulk density of the charge.

Jan 1, 1977

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

Jan 1, 1963

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By David Miller, James Santoro

Blasting is often required in urbanized areas to allow for economical execution of construction, demolition, and mining. Several examples of operations that require blasting in built up areas include: rock blasting for foundation and utility excavations; surface and underground mining for mineral extraction; and explosives demolition. Although explosives demolition is an engineering discipline, not at all like rock blasting, it still uses explosives for the felling of structures that have outlived their usefulness. Through the use of modem technology and implementation of extra safety precautions, explosives are used safely in congested areas to make the performance of critical work economical and feasible. This paper discusses several precautions required when undertaking various types of rock blasting and explosives demolition in congested areas. It also presents the adverse effects that must be considered when blasting in congested areas. The effects identified include flyrock, vibration and airblast, fumes, and non-elastic (permanent) ground deformations/overbreak. Measures for mitigating and controlling these adverse effects to provide on-site and public safety are presented.

Jan 1, 2000

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

Jan 1, 2002

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

By John F. Beesley

INTRODUCTION This paper discusses the design of the subsurface nuclear waste repository at Yucca Mountain, Nevada; and possible concepts for construction of the subsurface facility. Subsurface construction at Yucca Mountain is planned to last for 20 or more years, and may be accomplished using tunnel boring machines (TBM), drill and blast methods, raise bore machines, and roadheaders. The design of the subsurface facility includes approximately 107 km (66 miles) of tunnels and drifts. The vast majority of the repository will be excavated with TBMs. Design and construction concepts for the subsurface repository discussed in this paper are based on the License Application that was submitted to the U.S. Nuclear Regulatory Commission (NRC) by the U.S. Department of Energy (DOE) on June 3, 2008. The License Application was subsequently docketed by the NRC in September 2008. When a Construction Authorization is received from the NRC, notices to proceed with subsurface construction at Yucca Mountain will be issued by DOE. The Yucca Mountain site is located in the Mojave Desert approximately 150 km (90 miles) northwest of Las Vegas, Nevada. The site is on federal land in southern Nevada and is shown in Figure 1. Yucca Mountain is a ridge of volcanic rocks com-posed primarily of solidified volcanic ash. Previous underground construction work at Yucca Mountain included excavation of two tunnels using two different TBMs. The first tunnel, the Exploratory Studies Facility (ESF), is a 7.62 m (25 ft) diameter tunnel that is 7,877 m (25,843 ft) long and was described by Morris and Hansmire at the Rapid Excavation and Tunneling Conference (RETC) in 1995. The second tunnel, known as the Enhanced Characterization of the Repository Block (ECRB), was a TBM drive of 5.0 m (16 ft, 5 in.) in diameter and 2,681 m (8,796 ft) long. The second tunnel was excavated in 1998 and was described by Fulcher, Eastlund and Copeland at RETC 1999 and is named the East?West Cross Drift in that paper. (These previously excavated tunnels are shown in Figure 2.) In the volcanic rock formation where the vast majority of the planned repository will be con-structed, previous tunneling conditions were generally very good.

By N. Z. Fotoyi

Keywords: MgO-MgR2O3 refractory, SO2-containing gases, chemical attack The reaction mechanisms occurring when MgO-MgR2O3 refractories are exposed to SO2-containing gas atmospheres were examined. The study examined the characteristic structures of magnesite-chrome, chrome-magnesite and magnesite refractories exposed to SO2-O2 gas mixture at temperatures of 700°C to 1350°C. The phase characterization was conducted with scanning electron microscopy (SEM) and powder X-ray diffractometry (XRD). The results show that the physical characteristics of the refractory matrix along the grain boundaries are important refractory features during chemical attack from SO2-containing gas. Upon heating in SO2-containing gas, the changes in phase-chemical compositions and accompanying grain growth causes loosening of the structure and the pore volume promotes gas diffusion. The chemical reactions that occur form stable sulfate compounds identified as MgSO4, CaSO4 and CaMg3(SO4)4, and lead to disintegration of various phase structures and consequently erosion of the refractory. In conclusion, the reaction mechanisms in MgO-MgR2O3 refractories exposed to SO2-containing gases progress through a combination of structural disintegration and chemical attack.

Jan 1, 2011

By Eugene Frey

"INTRODUCTION The Iron Mountain deposits were examined in the summer of 1943 by engineers of the Bureau of Lanes, and a diamond-drilling project was set up under the Strategic Minerals Program. Actual drilling operations, under the supervision of a Bureau engineer, commenced November 9, 1943, and were completed on November 1, 1944. When the Bureau began detailed exploration of the Iron Mountain deposits, the Federal Geological Survey participated. Dr. I. W. Newhouse, of the Survey, and Dr. A. F. Hagner, of the Wyoming Geological Survey, were assigned to the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, acknowledgment is made to S. R. Zirrmerley and F. T. Allsman, Bureau of Mines, Salt Lake City, Utah, who supervised the work of this project."

Nov 1, 1946

By P. A. Cox

The purpose of the initial research performed under this contract was to determine the margins of safety in explosion-proof (XP) enclosures, which were designed and certified according to the current schedule (Schedule 2G). Results from this work provide baseline data on the current schedule, from which a new schedule can be formulated to give equal or greater levels of safety. Results and discoveries in the initial work led to an expansion of the contract to cover, additionally, weld quality in enclosure fabrication, reliability of enclosures with windows and lenses, and performance tests for enclosure qualification. Finite element calculations and hydrostatic tests revealed wide variations in the margins of safety in the enclosures studied; however, only one enclosure had a safety factor which was less than one. Results from a weld quality survey led to the recommendation of AWS Welding Standard D14.4 for the fabrication of XP enclosures. Based on other work, accelerated aging tests were recommended for qualifying plastics and adhesives that are used in some enclosures, and a Structural Performance Test was developed to test enclosure strength for a minimum static pressure of 150 psig.

Jan 1, 1982

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

The observation of lower-than-predicted Fe/Cu ratios in the cementation of copper on iron in tests at elevated temperatures indicated that some other reaction was contributing to the reduction of cupric sulphate in addition to the reduction by elemental iron. Experiments showed that the copper sponge, which initially formed on the iron, subsequently reduced the cupric sulphate giving the products cuprous oxide and sulphuric acid.Tests were undertaken to determine the rate and equilibrium conditions of the reduction reaction with variations in the types of the reducing agent and solution parameters. The reaction first became apparent at temperatures above 50°C and as it ceased at pH 1·8 it was possible to induce further reaction by alkali addition.

Jan 1, 1974

By Zwaan J, Kepa J

Ok Tedi mine has become one of the major copper producers in the world. In the process of becoming of age, it overcame the challenges of operating in a locality which is young in geological terms, experiences very high rainfall and has a topography which gives rise to frequent landslides. This paper discusses some of the geological, mine and geotechnical engin- eering aspects of the Mt Fubilan ore deposit.

Jan 1, 1991

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009