Search Documents

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By Kennedy G. L

Experience is reporled in the operation of the pilot Lurgi carbonization plant at Morwell, afler it had been reconstructed to obtain better control of the heating of the briquettes in order to produce a strong char suitable for use as a metallurgical fuel. The theoretical Ideal Heating Cycle, which had been designed from earlier laboratory research, was closely approached in the carbonizer, and up to 97 per cent of the whole dried briquettes entering the carbonizer were recovered unbroken in the char.The strength of the char produced in the pilot plant was limited by the performance of the drier where the cracking and breakage of the briquettes was more severe. Theoretical studies have indicated that this limitation could be removed by using a hot briquette feed to the pilot plant. Experience indicates that with a hot briquette feed to the drier and with ideal heating in the carbonizer, hard char could be produced from Yallourn briquettes in continuous operation.The project has been terminated for economic reasons...

Jan 1, 1966

The following list contains the names of members whose death notices have been printed in MINING AND METALLURGY from March 15, 1947 through March 15, 1948 Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns Year of Election - Name - Date of Death - Issue Containing Biography - Page 1938 ABERNATHY, G E , (M) Feb 6, 1948 April 1948 266 1935 ARCHER, M T, (M) Oct 26, 1947 Dec 1947 633 1947 ATIKINSON, JAMES E, (S) Feb 6, 1948 June 1947 309 1940 AYRES, VINCENT L, (M) Oct 14, 1947 Jan 1948 59 1915 BABCOCK, JAMES E , (M) April 1, 1947 June 1947 309 1942 BAGGALEY, WILLIAM BLAIR, (A) Aug 28, 1947 Jan 1948 59 1897 BUIN, II POSTER, (M) Mar 9, 1948 April 1948 219 1945 BAMPFIELD, A E (M) Unknown Mar 1948 215

Jan 1, 1952

By J. G. Pippenger

The mining industry has been Australia?s major economic driver over the past decade, contributing 8% to Australia?s Gross Domestic Product and 26% of Australian Stock Exchange Market capitalisation. Australia is the world's leading exporter in coal, iron ore, alumina, lead and zinc; and second largest in gold and uranium. While driving the economy, this resource boom has also created a demand for professional and operating talent that has far outstripped the capacity of Australia?s 21 million residents. I moved to Australia some 10 years ago and have not looked back. This unique island continent with its mix of Indigenous and diverse immigrants ? many still proud of their convict ancestry ? has offered life long memories both professionally and personally.

Jan 1, 2011

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By D Caley

During the response to the Moura No 4 disaster, use was made of the New South Wales Mines Rescue Service’s ‘Mineshield’ inertisation equipment. The equipment had to be transported from Newcastle, approximately 1400 kms, and the liquid nitrogen a similar distance. The time taken, and therefore availability of the liquid nitrogen, became a significant problem. Operational issues were also experienced during use. Typically the liquid nitrogen is converted to a gas (vaporised) before being injected into the mine. However, as the propane gas tanker used for the vapourising unit was delayed, an attempt was made to inject the liquid nitrogen directly down uncased boreholes. This proved unsuccessful.Following the Moura No 4 disaster and the Moura No 2 disaster, recommendations were made relating to having inertisation capacity for the Queensland coal mining industry. Today the Queensland industry has multiple options available for inertisation, including the high-volume GAG and smaller volume units such as boilers and membrane separation units. Although it ultimately aided re-entry into Moura No 4, most likely due to the issues associated with supply to Central Queensland, liquid nitrogen has not found favour within the Queensland industry as an inertisation tool.Coregas has commissioned an air separation plant in Mackay, improving the availability of liquid nitrogen to Central Queensland. Based on the availability of this nitrogen, recent sealing operations at Kestrel have trialled using liquid nitrogen and associated vapourising units. This paper details the practical application and findings of using liquid nitrogen during routine longwall panel sealing.CITATION:Caley, D, 2017. Using liquid nitrogen for the inertisation of goafs, in Proceedings Australian Mine Vent Conference 2017, pp 35–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Richard A. Grieve

A 63.5 metric tons per hour (70 TPH) demonstration coal preparation plant was constructed on the Iowa State University campus, Ames, Iowa, as a part of the Iowa Coal Project funded by the state of Iowa and administered through the Energy and Minerals Resources Re-search Institute. Processing equipment in the plant circuit includes a heavy media separator, concentration tables, separating and dewatering screens, and conveying equipment. Coal samples of size 907 metric tons (1000 tons) with sulfur contents ranging from 2.5 to 8.75% sulfur from seven mines in the state of Iowa have been pro-cessed in the plant. Sulfur reductions have averaged 35%. With ash reduction averaging 45%. Equipment for advanced fine coal beneficiation research is currently being installed in the plant to include a slurry pretreatment circuit, froth flotation, oil agglomeration, pelletization, hydrocyclones, advanced design thickener and disc filtration.

Jan 1, 1978

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

Sluice box operating practices in Papua New Guinea (PNG), and published work on sluice boxes are briefly reviewed. Some recent work on sediment entrainment mechanisms occurring in sluice boxes have also been described. In the light of this information, some drawbacks in the commonly adopted sluice box operating practices in PNG, and ways of overcoming them, are also highlighted.

Jan 1, 1991

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By Jacob Chacko

The Izmit Bay bridge, a 3-km-long suspension bridge crossing of Izmit Bay, Turkey is planned to be constructed in one of the most seismically active places in the world. The site, which has the potential to experience significant earthquakes associated with the relative motion accommodated on the North Anatolian Fault, is underlain by deep deposits of soft soils, and areas of unstable and liquefiable soils. Characterizing the seismotectonic setting, foundation soil conditions, potential fault locations, as well as other geohazards was a critical component for the project concessionaire to finance the project and obtain meaningful bids for bridge design and construction. Given the Build Operate Transfer (BOT) funding mechanism, executing this work in the least possible time was critical to the concessionaire?s financing scheme. Fugro was retained to provide geotechnical, geological, and seismological evaluations for the project region, and to generate data for contractors to develop reliable designs and bids. The uncertainties in these data made it difficult for the BOT concessionaire to finance the project and tender Bridge design and construction. The investment in an early and comprehensive site characterization program to evaluate and quantify those uncertainties allowed the concessionaire to save schedule, provide a robust bid basis to bridge contractors, and persuade banks to finance what was perceived to be a relatively high risk project.

Jan 1, 2011

By Mao Bai

In predicting the integrity of under-mined structures, surface horizontal displacements and curvatures are frequently of greater importance than the more homogeneous vertical displacements. Accurate evaluation of mining induced subsidence and horizontal displacement further requires that the predictive model adequately represents the subsurface geology, mining geometry and extraction sequencing. The following documents an extension of the Subsidence Prediction and System Identification method (SPASID) to the evaluation of horizontal strains. Comparisons are made between predictions from SPASID and two other empirical methods against measured data from a case study. The system identification method is illustrated to predict horizontal displacements and strains most consistently with the in situ data.

Jan 1, 1989

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012