Search Documents

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

The Manto Verde mine is found in the coastal ranges of the Atacama desert, 1000 km north of Santiago, Chile . The deposit is a fault-breccia specularite-oxide copper mineralisation hosted by the Jurassic andesites of La Negra Formation. It is located in a tensional fault that joins twoparallel arms of the Atacama Fault. The mine is in feasibility study: reserves are of the order of 60 Mt at 0.9 wt per cent soluble copper; mining will be undertaken at a rate of 11 000 tpd utilising an open pit and the ore will be heap-leached with acidified sea water, with copper recovery and by SX/EW.

Jan 1, 1992

By E. F. Schnitzer, D. R. Haight, G. T. Krogman

The 1997 New Year’s Day Rogue River flood near Medford, Oregon, USA, entered historic channels, eroded a 150-foot-wide buffer, and captured an inactive gravel pond located within the channel migration zone. Channel redirection caused by pit captures threatened adjacent inactive gravel ponds. In response to this capture, a stakeholders group of concerned individuals and organizations was formed. This group ultimately developed a rehabilitation plan, which conformed to the Rogue River’s geomorphic trends. A two-dimensional model, FLO-2D, was used to evaluate channel splits, flood storage, backwater, and future conditions. Modeling results coupled with trend analysis were used to create a stable design where stream barbs, gravel redistribution, a channel outfall spillway, bendway weirs, bank reshaping, and revegetation were integrated into a single plan for a three-mile reach. The quick action by the stakeholders group averted further damage to the Rogue River system and surrounding environment. The project has preserved three miles of mainstem habitat, one mile of side channel habitat, and protected ten gravel ponds from pit capture.

Jan 1, 2006

By Renan de Matos Silva

Em função da necessidade constante da redução de custos e aumento da vida útil de equipamentos do setor industrial (como siderurgia, Mineração, entre outros), Aumenta-se a procura por soluções técnicas para tais necessidades. Uma excelente alternativa é fornecer aos equipamentos proteções superficiais que garantem resistência aos mecanismos de desgastes. As perdas econômicas geradas por desgastes prematuros são críticas e generalizados. Estes custos não são somente correlacionados a reposição de novas peças, mas também, paradas de máquinas, perdas de produção, de competitividade e de oportunidade de negócios. Visando melhor atender às necessidades dos clientes e potencializar a performance dos equipamentos, a SMS Group vem desenvolvendo e empregando novas tecnologias de revestimentos por aspersão térmica, com estudos criteriosos apresentando soluções práticas e viáveis.

Oct 30, 2017

By Patterson J. H

An infra-red absorption study has been made of crocidolite, country rock. and associated host rocks from Wittenoom Gorge. The spectrum of the country rock is appreciably different from those of crocidolite and the magnetite-rich host rocks which are closely similar. A process to separate crocidolite-bearing ore from country rock based on infra-red emission is therefore possible in theory.

Jan 1, 1966

By [D. N. ] Naresh

During different activities pile installation like pile boring, concreting etc., it is likely that various problems, depending up on site condition may be encountered. There are possibilities that some of the activities if not correctly followed may affect the pile capacity. This paper describes few problems encountered during pile execution at different sites and presents the remedial measures undertaken to overcome them.

Jan 1, 1996

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By Lewis PJ, Halfpenny R, Craighead GA

Exploration drilling by Joint Venture partners CRA Exploration Pty Ltd and Elders Mining PNG Pty Ltd has discovered a signif- icant copper and gold deposit at the Wafi River prospect, 60km WSW of Lae in Papua New Guinea. An indicated resource of 18Mt at 2.5g/t Au using a lg/t cutoff has been delineated in Zone A. No estimate has been determined for the separate copper occurr- ence at Rafferty's Zone but the copper will be significant to the project. Metallurgical studies on the gold indicate that the primary ore is refractory to direct cyanidation giving a highly variable and inadequate response. All conventional refractory ore oxidation techniques perform well on both ore and pyrite concentrate and oxidation occurs rapidly. No metallurgical studies on the copper mineralisation have been undertaken. Hypogene covellite and chalcocite copper mineralisation is associated with an intensely quartz-stockworked, and quartz and alunite-altered intrusive. Economically significant gold mineralisation occurs in distal subhorizontal lenses, within a sedimentary host, that plunge toward the intrusive. These lenses are sandwiched between overlying quartz and alunite-altered zones and underlying quartz and smectite zones in a mixed zone of quartz, dickite, kaolinite and illite alteration. The alteration and mineralisation is classified as a high sulphidation, epithermal style resulting from the influx of hot, acid magmatic fluids. Preliminary land ownership, road access, power supply and mine infrastructure studies are in progress. The project is currently at an advanced exploration stage.

Jan 1, 1991

By R. Chryst, R. Kus

In the Integrated IT Systems proposed by Przedsie? biorstwo Robót Geologiczno-Wiertniczych—Geological and Drilling Company (PRGW) a network connects a database with all of the departments of a mining division. A key element thereof is the common graphics environment—Micro Station supplied by the firm, Bentley. PRGW’s SoftMine software and GMSI’s CadsMine that are used to design and schedule mining operate in this environment. The digital form of the design project facilitates the verification of information and the integration of technical solutions with SAP R/3 type financial—accounting systems. The system has been successfully implemented in the Brown Coal Mine in Poland.

Jan 1, 2003

The structure of the Bulli coal seam at Appin Colliery was detailed by the seismic reflection method. This unusual application of the seismic method was possible because there is a reflector near the seam as was revealed during exploration for petroleum in an area north-west of Appin. The reflector, which was at a depth of 1,500 ft, was shallow by normal reflection survey standards. Measurement of the seismic velocity at two ventilation shafts showed that the reflector was probably the Bulli coal seam. Accurate depth control was established from previous drilling results.INTRODUCTIONAppin Colliery, situated on the Southern Coalfield of N.S.W. (Fig. 1), is being developed to supply coking coal to the Port Kembla steelworks of Australian Iron and Steel Pty. Ltd. The colliery is mechanized and a detailed knowledge of structure, particularly faulting, is important in planning the workings.The Bulli seam, which is approximately 9 ft thick, and between 1,500 ft and 1,800 ft below the surface, is worked in the colliery. It is the uppermost member of the Permian Coal Measures and is overlain by Triassic rocks, which consist of thick sandstone beds containing beds of coloured shales, and which are subdivided into the Narrabeen Group, the Hawkesbury Sandstone, and the Wianamatta Group.In the early stages of development of the colliery, surface geological mapping and diamond drilling provided information on structure. Generalized results of the mapping are shown on Fig. 2. Drilling indicated that the physical and chemical properties of the Bulli seam are relatively constant, and that the seam is nearly horizontal, the average dipbeing about 1 in 25 to the west.

Jan 1, 1965

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006

Situated in the Greymouth Coalfield, the Mt Davy Block contains a significant resource of high quality bituminous coal suitable for use in metallurgical coking coal blends. The coal, which is all low sulphur, is seen as a complementary deposit to export coking coal at Stockton Mine.   Previous drilling by State Coal Mines (1948 - 1953) and Japanese interests (1970's) have been supplemented by Coal New Zealand drilling (1992 - 1993) and surface mapping. A mining feasibility study was completed in late 1993 and approval gained for the driveage of an exploratory tunnel to the target seam.   Following construction of surface facilities, tunnel driveage on a 1:5 decline commenced from Rewanui in May 1995 and to date about half the required length has been driven. When the seam is intersected a comprehensive geotechnical testing programme will be undertaken to assess the in-situ mining conditions. It is expected that the results will confirm the assumptions made in the feasibility study.   The Mt Davy Mine, at depths of 500 - 700 metres, will be the deepest underground coal mine ever inNew Zealand and in-situ stresses (orientation and magnitude) will be important considerations for mining engineering. The coal has a high gas content and suitable techniques for gas control and prevention/mitigation of coal outbursts will be necessary.   Mine development is scheduled to commence in mid 1998 and an annual production level of 500 000 tonnes is forecast. The coal seams will be developed by continuous miner and coal extraction will be by hydraulic monitor. Coal will be pumped to the surface and from Rewanui transported five kilometres to Dunollie either by truck or slurry pipeline. At Dunollie a coal dewatering plant, coal stockpile and rail loadout will be constructed.

Jan 1, 1996

By W. V. Mutler

Present day capital costs are analysed for a 2 000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

U.S. Gold Commission Established. - The President, with the authorization of Congress, has named a gold commission made up of 17 individuals, most of them Government officials, to study U.S. policies related to the role of gold in domestic and international monetary systems and report its findings and recommendations to Congress. U.S. Lead Exposure Ruling. - On June 29, the Supreme Court upheld the Government's right to set lead exposure levels for employees at the workplace. The Court ruled in favor of the Occupational Safety and Health Administration (OSHA) in a challenge by a group that alleged that OSHA had failed to conduct a cost-benefit analysis prior to issuance of the lead standards. It was the Court's contention that Congress did not require such an analysis when it empowered OSHA to establish workplace standards. The petition to the Court was made by the Lead Industries Association Inc., Battery Council International Inc" American Iron and Steel Institute, St. Joe Minerals Corp., and other lead mining and consuming firms.

Jan 1, 1981

By Lawrence S. Darken

STAFF: Editor, Gerhord Derge Cornegie Institute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: J. S. Smart, Jr., President; C. C. Long, Past-President; K. L. Fetters, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: C. L. McCabe, Chairman; H. L. Bishop, K. L. Fetters, J. J. Harwood, W. A. Krivsky, F. C. Longenberg, R. E. Lund, W. 0. Philbrook, L. L. Seigle, R. L. Smith, and F. L. Vogal. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: C. L. McCabe, Chairman; R. E. Lund, Vice-chairman; D. H. Baker, Jr., W. A. Krivsky, R. A. Lewis, Paul Qusneau, A. S. Russell, R, E. Shinkoskey, W. W. Stephens, and M. E. Wadsworth. Institute of Metals Division: L. L.Seigle, Chair-man, P. A. Back, J. J. Backer, l.l. Bessen, J. 0. Betterton, Jr., J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, R. B. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurland, E. L. Harmon, J. J. Hager, A. A. Hendrickson, M. Harmon, J. N. Hobstatter, H. H. Johnson, Jr., H. 5. Kolish, R. R. Nash, T. N. Rhodin, R. H. Richman, W. Rostokar, P. G. Shawmon, C. W. Spencer, L. Slifkin, J. K. Stanley, C. D. Starr, R. Steinitz, and H. C. Stumpf. Iron and Steel Division: H. L. Bishop, Chairman; 2. E. Boni, F. C. Langenberg, J. B. Wagstaff, and T. V. Wainwright. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription PetroleumEngineers,$30 per year for non-AIME members in United States and North, South, and Central America; 332, foreign; $5 for AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1%1 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address; AIME New York ..Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts.. .Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 221, Number 4.

Jan 1, 1962