Search Documents

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By J. E. Conley

[Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft-paper industry, especially in Lie South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far re¬moved from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4?10H20), which must be dried or dehydrated in order to most consumer requirements. The waters of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery or production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.]

Jan 1, 1936

By Hebert Arias, Christian Mendoza, Mervin Tapia

El Complejo Pasco —ubicado en la Cordillera Oriental de los Andes de la sierra central del Perú, en el distrito de San Francisco de Asís, provincia y departamento de Pasco— está constituido por las unidades subterráneas de Atacocha y Porvenir, la operación a tajo abierto Glory Hole y tres proyectos brownfield ubicados en la periferia de la concesión. Tanto Atacocha como Porvenir son depósitos tipo skarn, con mineralización distal de Zn y Pb(+/-Au) y proximal de Zn+/-Cu, asociados a cuerpos hipoabisales de composición cuarzoandesítica y andesítica. Estudios y exploraciones recientes muestran otros tipos de sistemas mineralizados, como brechas tectónicas con reactivación hidrotermal tardía, un sistema epitermal de sulfuración intermedia en vetas, cuerpos irregulares, entre otros, y un sistema tipo pórfido. La Falla Milpo-Atacocha, de rumbo N-S, juega un rol importante, ya que los intrusivos (Stock Milpo y Santa Bárbara) que generan la mineralización del tipo skarn están controlados por esta falla. Existe otro tipo de mineralización, asociado al sistema NW-SE (Falla 13): un sistema epitermal de sulfuración intermedia. Este trabajo pretende mostrar los últimos avances en las interpretaciones metalogenéticas, producto de un intenso programa de exploración (aproximadamente 80,000 m. DDH / 2018) y de un programa de recategorización de recursos (a través de 60,000 m. DDH), que permitirá hacer posible una operación sostenible de 12 años.

May 22, 2019

The Broken Hill orebody ,occurs in the Willyama Complex, a block of Precambrian rocks which have been strongly folded and metamorphosed at moderate to high grade. Although -the origin of the silver-lead-zinc mineralization remains obscure, recent investigations have substantiated the view that the orebody has undergone concomitant high grade metamorphism with the enclosing wallrocks. The mesoscopic structures produced by this metamorphism are described, and the possible processes Telating to their formation are disoussed.In the high grade ore, metamorphic structures which can be recognized are foliation and lineation, wallrock fragments, layering, flow folds, ore breccias, and sulphide bearing veins. These structures can be related to processes involving plastic flow and fluid phase transport of the mineral assemblage. 'In areas of low grade mineralization adjacent to high grade ore, the structures more closely resemble those produced in -the wallrocks-foliatlon, lineation, layering, folds, and sulphide injections. Within areas of high grade ore, lenses and pods of manganese silicates Probably represent original inhomogeneities in the ore, i.e., portions of manganese-rich and sulphide deficient rock which have been metamorphosed to manganese silicates.From the structures displayed, a sequence of events has been established for the plastic flow of ore during deformation.

Jan 1, 1975

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By F. N. Kissell, C. M. McCulloch, Maurice Deul, J. R. Levine

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas content of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and desorbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By M Bannear, C Stanton

Since 2008, Arrium has been developing and commissioning a new low-grade hematite ore benefication plant (or OBP) at its Iron Baron mine site.The Iron Baron mine, which was closed in the 1990s, could not consistently yield the high-grade hematite required for pelletising. However, in todayÆs market, the 12 Mt of waste dumps represent a significant low-grade hematite resource, ideal for benefication.Initially, an internal scoping study and several sampling campaigns were conducted to determine the ability to upgrade the available low-grade dump material to a product suitable for export. Test work was conducted at Mineral Technologies (formerly CPG), and included high intensity magnetic separation, spiralling and jigging. Due to promising results from a wet processing circuit, Arrium engaged Mineral Technologies to design a flow sheet that could provide 1 Mt/a of a mixture of high-grade lump (-32 + 8 mm) and fines (-8 mm) products for export.With construction of the plant completed in late January 2012, Arrium, in conjunction with Mineral Technologies, began two commissioning phases. Each phase ended with a toll gate to prove the plantÆs capacity to reach rate and desired grade. After an initial period of running on water, feed solids were introduced to the plant and troubleshooting of bottlenecks began. The first toll gate, whereby the plant was required to run for 24 hours at an average feed rate of 200 t/h (80 per cent of design rate), was completed on the 1 March 2012. Further troubleshooting and resolving of issues allowed the plant to steadily increase feedrate while maintaining good availability and grade. The second toll gate required the plant to run for 72 hours at an average feed rate of 200 t/h while meeting grade, yield and water consumption targets. Sampling campaigns were conducted during this period to track the performance of key equipment. Completion of the test, and full handover of the plant to Arrium, was completed on the 21 April 2012.Although the formal commissioning phases had been completed, ongoing optimisation of the OBP continued, ensuring that all major equipment was working to produce the optimum yield and grade. Sampling campaigns were conducted on the jigs and spirals, with results and correlations used for operations documentation.Overall, with successful completion of the final acceptance tests, the commissioning of the Iron Baron OBP has been established as a major success achieving all production and quality targets as per the original design intent.This paper will focus on the successful commissioning and ramp-up performance of the plant however reference will also be made to the key development stages involved with the development of the project.CITATION:Stanton, C and Bannear, M, 2013. ArriumÆs Iron Baron hematite beneficiation plant - a success from start to finish, in Proceedings Iron Ore 2013 , pp 547-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Julver Álvarez

El presente trabajo describe el comportamiento estructural y mineralización del estaño-cobre en la mina San Rafael, Puno. En este sentido, las pizarras de la formación Sandia del Ordovisco Superior, por metamorfismo de contacto con el intrusivo, han sido transformadas a hornfels, que junto a las cuarcitas se presentan algunas veces como una cubierta superficial sobre el intrusivo. Asimismo, los intrusivos y las pizarras son favorables para la mineralización de estaño, aunque los cuerpos del mineral son más definidos y persistentes en el intrusivo.

Sep 13, 2001

By Fogarty J. G H

Ausmelt Technology has a unique capability of removing the impurities, phosphorus and sulphur, from the feed materials to the process. Sulphur is removed to the gas phase almost completely because of the interactions of ore and coal in the reaction region at the top surface of the slag bath. Phosphorus is removed to the slag phase, with both basic and higher, controlled iron oxide levels in slag being achieved in the process. The significance of these features of the process relate to the production of pig iron with very low levels of these impurities for the further processing to steel, and to the treatment of high phosphorus and high sulphur raw materials. The marketability of pig iron and the raw materials are discussed in relation to this feature of Auslron.

Jan 1, 1999

By J. A. Holmes, EDWARD C. FRANKLIN, RALPH A. GOULD

The commission may be permitted to express its earnest hope that the litigation which comes to an end with the findings and recom- mendations herein set forth will be considered by both parties to the action as definitely and equitably decided. The commission trusts that its work will show the value of the commission form of settlement and that its work will serve as a prece- dent to be followed in disputes relative to technical subjects. If the work of the commission is productive of a tendency on the part of technical litigants to avoid the use of the courts for the settlement of disputes it will not have been done in vain. Such tendency will surely grow and ultimately such differences will be arbitrated by technically trained men without recourse to the courts of law. Appended to the report of the findings of the commission are to be found the detailed reports covering the several lines of inquiry and investigation carried on by the commission and upon which its findings are based, and also a detailed statement of the fiscal affairs of the commission. A word of explanation is necessary in regard to the fiscal statement. While each party to the litigation has agreed to bear one-half of the expense of the investigations of the commission, it will be noted that the Selby Smelting & Lead Co. is credited with $21,000, while Solano County is credited with but $6,000. In order that the investigations of the commission might go forward without interruption the Selby Smelting & Lead Co. has generously supplied funds at the times they were needed. This assistance has been

Jan 1, 1915

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

Six simulations by the Mpnte Carlo method employing both classical and geostatistical techniques are presented for the determination of the probability distribution of the in situ value of a coal seam. To avoid the problem of qualitative estimation of parameter variability in the calculation of an arbitrary seam value, only data values from borehole information were used to quantify the variation in four coai seam parameters.The method which is suggested as being the most appropriate is a particular geostatistical approach that employs the best linear unbiased estimate and the error of estimation for a number of two dimensional blocks. The results indicate that the variance of the coal seam unit value may be much higher than that indicated by the classical approach because of the spatial variability that is properly incorporated in the geostatistical approach.The model used in the Monte Carlo simulation to determine the economic value of a coal seam can be extended to incorporate all those parameters which are necessary for a true estimation of the probability distribution of the coal seam value. A time value concept for discounting can also be incorporated to optimize the economic return of a coal mining project.

Jan 1, 1983

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By A. Koski

A pond rehabilitation and environmental education project were proposed by Cleveland-Cliffs Michigan Operations (CCMO) and approved by the Michigan Department of Environmental Quality (MDEQ) and the United States Environmental Protection Agency (USEPA) as partial fulfillment of conditions for a stream mitigation permit. The goals of the project were the rehabilitation of a pond on a tributary of a local trout stream, enhancement of public access and appreciation, and the initiation of a site-based environmental educational curriculum. Cleveland-Cliffs undertook a suite of actions to rehabilitate a pond created by a previous mining operation in 1912 and make accessible to local schools the aquatic and riparian ecosystems. Cleveland-Cliffs partnered with the local governmental unit and two local school districts. The rehabilitated pond and riparian zone provide an accessible natural area that local residents can use for such activities as hiking, biking, walking, fishing and nature study. Vegetative enhancement includes the planting of native shrubs, wildflowers and showy herbaceous plants in the pond, on the riparian fringe and the surrounding area. An interpretive trail was developed around the pond with signs created by a local master watercolor artist. Local schools built and installed picnic tables, benches and a kiosk. Cleveland-Cliffs created pond lesson plans tied to the Michigan Curriculum Framework, developed inexpensive teaching kits and hosted a workshop for teachers from nine local schools. Classes regularly utilize the pond during the school year conducting environmental studies. Nesting boxes, wildflower gardens, bat houses, frog deformity surveys and water quality studies are a few of the activities that classes have conducted at the pond.

Jan 1, 2007

By L. B. Slichter

Prospecting is certainly the world's biggest and best gambling business. It is a game where the chips cost many thousands and where many millions, even billions, can be won. An attractive feature of this gamble is the fact that the players are free to rig the odds as favorably as possible. Only the limited bounty of nature, the restrictions of the laws of the land, the competition from other players, the limited sagacity of the player himself— only these, and other factors, restrict the possibilities for large winnings. Today probably about half the land surface of the earth remains to be searched for signs of ore visible at the surface. It is fortunate that so much land still remains for exploration by relatively economical methods. Looking to the future, it is a good guess that the costs of finding ore will increase in response to increasing technical difficulties. To continue to achieve profits from prospecting, it will become necessary to analyze the business more skillfully, in a more and more sophisticated manner. Whenever feasible, qualitative concepts must be replaced by their quantitative equivalents, improvements, and extensions. THE GAMBLE The fact that prospecting is a gambling business reminds us at once of the elementary rule known as the law of gambler's ruin. I hesitate to mention so simple a rule in this company of experts. This rule expresses the rather serious chance of going broke when the odds for success are small, merely by a normal run of bad luck regardless of the long-run expectations of gain. The only sure way of avoiding this special risk of gambler's ruin is to have enough capital, and the will, to continue the play many times and thus ride out the inevitable runs of bad luck. For example, if the probability of success is one in ten for each venture, there is a 35 pct chance that ten successive ventures will fail in a row. But if one has the capital to continue the play through a run of 100 failures, then the chance of gambler's ruin is only 5 in 100,000. Almost any management, I suppose, would be under terrific pressure to cease the play during a long run of bad luck. To continue to prospect under such circumstances requires great confidence in the premises, and a firm conviction in the long-term expectation of profit. There is evidence which I shall mention that in the future even the strongest companies may not have the necessary capital to prospect on the ideal scale. Joint ventures will be very desirable as a means for extending the available venture

Jan 1, 1961

By CIMVAL

This Code for the Valuation of Mineral Properties (the “CIMVAL Code”) is the result of a review more than a decade after the release in 2003 of the “Standards and Guidelines for Valuation of Mineral Properties” (the "2003 Standards"). The purpose of the review is to update the 2003 Standards to reflect domestic valuation, international valuation, and regulatory developments. The CIMVAL Code was adopted by the Canadian Institute of Mining, Metallurgy & Petroleum (the "CIM") Council on November 29, 2019. The CIMVAL Code supersedes the 2003 Standards. The 2003 Standards were dated February 2003 and were adopted by the CIM Council on March 9, 2003 as the first comprehensive set of standards for Valuation of Mineral Properties in the Canadian mining industry. The 2003 Standards followed recommendations of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission, where in its Final Report (January 1999), the CIM was specifically asked to form a committee of valuation practitioners to review and advise on standards for the Valuation of Mineral Properties. The Special Committee on Valuation of Mineral Properties ("CIMVAL") was created on May 5, 1999 with the mandate to recommend standards and guidelines for Valuation of Mineral Properties to be used by the mining industry in general. The CIMVAL Code is limited to the Valuation of Mineral Properties (including any interests therein) and does not cover valuation of corporations or other entities that hold Mineral Properties as assets. The CIMVAL Code does not cover petroleum and related assets. CIMVAL recommends that the CIMVAL Code be followed for all Valuations of Mineral Properties, including those required by securities administrators and stock exchanges. However, when a Valuation is required under the applicable rules of securities administrators or stock exchanges, such rules prevail to the extent of any inconsistency.

Nov 29, 2019

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970

Vale Inco?s Coleman Mine 153 Orebody is a narrow vein deposit with a dip that varies from 30 to 70 degrees. It has a strike length of 1200-feet and the current mining extends from the 4250 level to 5100 level. The primary mining method is mechanized cut-and-fill although drift-and-fill is also used in wider sections of the ore zone. The ore body is divided into six main mining horizons with an average of three mining blocks on each cut. There are some interesting rock mechanics challenges related to mining upward from the 4550 level and these challenges are increasing as the mining front progresses toward the 4400 level. The mining of the 4550 block is currently at cut 13 whereby the crown pillar thickness is approximately 60-feet. Significant factors including increased stress levels in the crown pillar, the change in the orebody dip at this level and a recently indentified geological structure in the footwall, have all combined to introduce seismic activity in the footwall of 4550 level. Closer studies revealed a consistent trend of seismicity that was further examined with core logging and Acoustic TeleViewer technology. The data from these assessment tools disclosed a geological structure that is influencing the mining environment. This paper reviews the seismic analysis for the 4550 level mining zone and the subsequent procedures used to locate the new geological structure. The paper also discusses the key mining practices used to successfully mine cut 13 of 4550 level and briefly reviews the studies that are underway to up-date the mine design for continued extraction of high-grade ore in a safe and productive manner.

May 1, 2009

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By Horacio Reeves

Las maquinarias son elementos importantes en el proceso de minería de tajo abierto -en tanto optimizan el rendimiento del trabajo y de los operarios. Sin embargo, su contínuo uso conlleva riesgos ocupacionales en el trabajador como la exposición a vibraciones de cuerpo entero en el caso de equipos pesados. En ese sentido, el presente texto compara los niveles de vibración en los equipos pesados que operan en Antamina con el estándar europeo: Directiva 2002/44/CE, así como los efectos de este en los operarios.

Sep 12, 2005