Search Documents

By José Vidalón

Las aguas del río Santa son aprovechadas para la generación de la electricidad de la Central hidroeléctrica de Cañon del Pato, así como la irrigación de tierras agrícolas. Sin embargo, durante una evaluación ambiental territorial de su cuenca, se encontró algunas fuentes de contaminación por minas inactivas, depósitos de relaves y botaderos de desmonte abandonados. En ese sentido, el presente texto refiere el programa de impacto ambiental aplicado en la cuenca por el Ministerio de Energía y Minas. De acuerdo a este monitoreo, se concluyó que pese al desemboque de otros efluentes contaminantes, la calidad del agua cumple con las clases de la ley general de las aguas y puesto que tiene una capacidad de neutralización de las sustancias ácidas. Asimismo, en los puntos de las cuencas aguas abajo de operaciones minero metalúrgicas que utilizan cianuro, el contenido del reactivo es menor al establecido por ley y es apto para consumo doméstico y riegos agrícolas.

Sep 13, 2001

By D. Lunt

Telfer bulk concentrates typically contain 8% chalcopyrite, 8% chalcocite, 45% pyrite and 80-120 g/t gold. Although very high copper and gold recoveries can be obtained by subjecting the concentrate to a "conventional" high temperature pressure oxidation step followed by copper recovery by solvent extraction and electrowinning, and cyanidation of the leach residue for gold recovery, the cost of lime required for neutralisation and power for oxygen generation was such that the process was uneconomic in terms of operating costs. The challenge therefore was to develop an alternative flowsheet that maximised copper and gold recovery in which the reagent costs were commercially attractive. An additional objective was to reduce the capital cost so that the overall NPV and IRR values would enhance the economic viability of the total project. Following a series of batch and locked cycle testwork programs, supported by Metsim modelling, it was established that the same high levels of overall copper and gold recoveries can be obtained by use of a novel two-stage split leaching circuit in which the chalcocite component is leached in a low temperature (90-110°C) circuit with the chalcopyrite component treated in a high temperature (220-250°C) circuit. This split circuit has a number of advantages, including minimising the required capacity of the high temperature autoclave, as well as reducing the overall lime consumption and simplifying the total process water balance. The paper outlines the basis for the development of the flowsheet and discusses the integration of the leaching stages into the overall circuit.

Jan 1, 2004

By Pedro Jorge Walburga Keglevich de Buzin

O cloro no processo de aciaria elétrica tem sua principal fonte nas contaminações de origem orgânica existentes nas matérias-primas usualmente empregadas, principalmente na sucata. Apesar dos atuais níveis de cloro não perturbarem a fabricação do aço nas mini-mills, a presença deste elemento e dos compostos por ele gerados tem influência deletéria nos aspectos laborais, ambientais, de manutenção das instalações e na reciclagem das poeiras de aciaria. Neste trabalho, com base na integração de dados da literatura, da indústria e de propriedades físicas, químicas e termodinâmicas das substâncias envolvidas é feita uma avaliação qualitativa da passagem do cloro na aciaria elétrica e sua distribuição nas diversas correntes de massa de saída do processo. Foi concluído que a maior parte do cloro que entra no FEA deixa o sistema concentrando-se nas emissões do processo, principalmente nas poeiras de aciaria, sob a forma de cloretos alcalinos.

Oct 30, 2017

By Amélia de Santana Cartaxo

Nos dias atuais, a concorrência comercial estimulada pelas grandes empresas multinacionais tem direcionado o rumo das pesquisas cientificas para o aperfeiçoamento ou busca de materiais que ofereçam atrativas propriedades físicas ou químicas. O objetivo desse trabalho é analisar a influência dos métodos de síntese nas características estruturais do pó de titanato de bismuto. Foram sintetizadas amostras de titanato de bismuto pelos métodos Pechini e reação de combustão. As amostras sintetizadas foram submetidas as análises de difração de raios x, microscopia eletrônica de varredura, área superficial pelo método BET, tamanho de partícula por espalhamento dinâmico de luz, análise térmica pelas técnicas TGA, DTA e DSC. Todos os pós estudados apresentaram morfologia semelhante. As perdas de massas ocorreram em maior escala para as amostras produzidas pelo método de reação de combustão. A fase de titanato de bismuto formou-se em ambos os métodos, entretanto a fase teórica (estequiometria 1:1:3) desejada não foi formada.

Oct 30, 2017

By Francisco Belmino Romero, Walney Silva Araújo, Vitória Lima de Souza, Edilberto Rocha Silveira, Adriana de Oliveira Sousa Leite

O uso de inibidores verdes na corrosão do aço carbono SAE J403 1020 configura-se como uma alternativa econômica e ambientalmente acessível, pois, em relação aos inibidores comerciais geralmente utilizados, são de fácil obtenção, já que são adquiridos a partir de vegetais, portanto, não oferecem risco ao meio ambiente. Assim, o presente trabalho tem como objetivo avaliar o uso das folhas de aroeira como inibidor de corrosão para o aço carbono SAE J403 1020, o qual é bastante utilizado na indústria e possui baixa resistência à corrosão. A escolha da aroeira se deu devido ao fato de a planta ter origem no Brasil e abundância no Nordeste do País, principalmente no Ceará. Para análise, foram utilizados como meio corrosivo: H2SO4 0,1 M, NaCl 3,5% e NaCl (ph = 4,0); as concentrações do inibidor foram: 50, 200, 500 e 1000 ppm. Em relação aos ensaios eletroquímicos, utilizou-se: Potencial de Circuito Aberto (OCP), Espectroscopia de Impedância Eletroquímica (EIE) e Curvas de Polarização Linear (CP). Dessa forma, por meio da análise das técnicas mencionadas, conseguiu-se obter o comportamento do inibidor em relação ao material e ao meio, bem como avaliar qual o melhor meio para a utilização da aroeira como inibidor verde de corrosão.

Mar 1, 2019

By Verônica Scarpini Candido

Este estudo tem por objetivo caracterizar o pó de balão proveniente de uma siderúrgica do estado do Pará visando a sua incorporação em argilas para produção de blocos. O resíduo passou pela etapa de beneficiamento e, depois, foi realizada a difração de raios-X (DRX) e fluorescência de raios-X (FRX). Além disso, realizou-se também a análise morfológica por microscopia eletrônica de varredura (MEV). Os resultados mostraram que hematita, magnetita, goethita são as fases predominantes. A análise química por FRX mostrou que o resíduo apresenta baixos teores de sílica (SiO2) e alumina (Al2O3) associados a elevados teores de óxido de ferro III (Fe2O3). Dessa forma, a caracterização do pó de balão mostrou que esse resíduo apresenta-se como um potencial constituinte mássico cerâmico e que os elevados teores de óxido ferro podem contribuir para melhorar a cor dos produtos finais.

Oct 30, 2017

By Alejandro Trujillo Cabanillas

El presente texto señala las características del yacimiento geológico Cerro Lindo determinándolo como parte del tipo sulfuros masivos volcanogénicos (VMS) y propone un modelo genético de su formación genética. El yacimiento minero Cerro Lindo se ubica en Ica, Perú y es depósito de sulfuros masivos volcanogénicos donde dichos sulfuros bandeados de baritina y Zn se depositaron por precipitación de los fluidos hidrotermales calientes en contacto con el agua de mar. A medida que la temperatura ascendía en las celdas hidrotermales, se desarrollan los sulfuros piritosos con los fluídos cupríferos, de forma que las fallas sin volcánicas sirvieron para que la ocurrencia de bajos estructurales donde se desarrollaron cuerpos de gran potencia, determinen los altos estructurales que preservaron sulfuros masivos de alta ley de zinc.

Sep 9, 2007

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By W. H. Stahl

The continuous vacuum filtration is the solid-liquid separation process that is nowadays most frequently used in the beneficiation industry all over the world. After a development time of several decades, the various filter types such as drum filter, disk filter, plate filter and belt filter can be consideres as a sound functional design ensuring a trouble-free operation. Nevertheless, the vacuum filtration does no longer meet the present and future technological requirements. The moisture content of filter cakes is too high. Their thermal secondary drying is too expensive (coal, ores) and may bring about undesirable material changes and the filter cake conditioning with water-binding substances for dumping purposes is too costly.

Jan 1, 1983

By NEWTON C. MARSHALL

AS every school boy knows, the Andes mountain range forms the backbone of South America, extending the full length of the continent along its western edge and fairly close to the Pacific coast. But in Colombia these mountains are divided into three distinct ranges known as the Western, Central and Eastern ranges of the Andes. United at the southern end, they spread out like three fingers in a northerly direction across the Republic of Colombia. These great natural barriers have only in recent years been tarried by railroads or wagon roads, and they have had their effect upon the history of the country, both political and ethnological. Each of the three ranges dies out and dwindles away before reaching the boundary of Colombia on the Caribbean Sea. When I studied my geography as a youngster 1 used to think that the

Jan 1, 1935

By Yongsheng Song, Yong Chen, Wenjuan Li

"Detailed characterization and improved recovery of a micro-fine, low-grade refractory gold ore from a beneficiation plant in Yunnan Province, China, was investigated. Different analytical techniques, such as videlicet size analysis, scanning electron microscopy, and mineral analysis by a Mineral Liberation Analyser, were used for mineralogical characterization of the ore. This paper describes an experimental study on the effect of the grinding fineness and the use of various flotation reagent regimes involving collectors, depressors, and activators on the flotation behaviour of micro-fine auriferous pyrite. Two-stage flotation resulted in high gold grade (32.71 g/t) and gold recovery (80.02%) of the bulk gold concentrate. This process opens the possibilities of maximizing Au recoveries in a micro-fine low-grade refractory gold ore where low recoveries are common.INTRODUCTIONWith the rapid development of the gold industry, refractory gold ores are becoming increasingly important resources for gold production (O’Connor & Dunne, 1994; Agorhom, Skinner, & Zanin, 2012). Among these refractory gold ores, sulfur and micro-grained native gold ores represent a significant challenge, since they are not amenable to gold recovery by direct cyanidation. The gold contained in this type of ore is very finely disseminated and encapsulated in sulfides, which makes it inaccessible to the cyanide solution during direct cyanidation (Bulatovic, 1997; Allan & Woodcock, 2001). Autoclave pressure oxidation (AC POX) of the sulfide ore and subsequent cyanidation is a common technology used to recover the gold in such types of ore. Flotation is often used as a pre-treatment method to refractory gold ore (Monte Lins, & Oliveira, 1997).As the gold-carrier minerals are usually finely disseminated (sometimes under 10 µm) and intimately associated with gangue minerals, a fine grind is necessary to get a high degree of liberation. At the same time, the fine grind usually causes the production of significant quantities of slimes, which comprise easy-to-float gangue minerals such as mica, dolomite, and calcite. These mineral phases are naturally hydrophobic and float readily, competing with the value minerals in the froth phase and resulting in lower concentrate grades."

Jan 1, 2016

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By Kenneth S. Ritchie

THE discovery well of the world's -deepest oil producing structure, University 1-B of Group No. One Oil Corporation, in the Big Lake oil field, Reagan County, Texas, has had a remarkable record. The well is outstanding for the following reasons: (1) It is the world's pioneer well to produce. oil in commercial quantities from a structure 8500 ft. below the earth's . surface; (2) this well was the only. producer from the 8500-ft. pay for a period of 17 months and 24 days; (3) the flow of the discovery well has been free from-the customary changes at the casinghead, with the exception of putting on a back-pressure of 185 lb.; and, (4) the well's daily production of oil and gas increased rather steadily for 17 months and 18 days from an initial of 40 bbl. per day to a maximum of 2926 bbl. per day, and then six months later, after a period of decline and self-readjustment to subsurface changes caused by six more deep producers, the well set its real record for one day's production of oil at 2950 bbl

Jan 1, 1931

By Marcus Francisco Gonçalves Mesquita

As mudanças no plano estratégico de uma organização reverberam por todos os seus setores, gerando demandas de alinhamento estratégico. Entre estes setores estão os de planejamento e programação da manutenção. O presente estudo de caso descreve uma iniciativa de alinhamento estratégico realizada pela equipe de planejamento de manutenção da unidade Ubu da Samarco Mineração S/A, uma empresa de mineração e pelotização de minério de ferro, localizada no estado do Espírito Santo. A partir de uma revisão na estratégia corporativa foram derivados a missão, visão e valores da equipe. Esses por sua vez, serviram de base para uma revisão dos processos de trabalho e para a definição de ações de melhoria. Por fim foram estabelecidos indicadores para mensurar a realização da visão. Os resultados apresentados por esses indicadores comprovam que as equipes de planejamento podem obter e demonstrar resultados significativos através de técnicas elementares de planejamento estratégico.

Aug 7, 2018

By Luana De Lucca de Costa

O forjamento a quente em matriz aberta é, atualmente, o processo mais utilizado para a fabricação de peças de grande porte. Neste estudo, a simulação numérica foi utilizada, através do método de elementos finitos, para análise do processo de forjamento em matriz aberta de um eixo vazado e escalonado aplicável em aerogeradores. A partir de um billet cilíndrico vazado de aço AISI 4140, pesando 1 kg, é simulado o processo de forjamento objetivando a obtenção de geometria final apresentada. Utiliza-se matrizes superior e inferior em formato côncavo, e um mandril de manipulação com inclinação de 1,15°. A cinemática da simulação numérica, que inclui 4 passes com um número total de 30 cursos, é avaliada. Ao comparar a geometria apresentada com a obtida observa-se que o alongamento longitudinal da forma final é obtido. A partir da análise da temperatura, pode-se concluir que o reaquecimento deve ser realizado após cerca de 45 s, no final de cada série de 5 cursos.

Aug 8, 2018

By Zhucheng Huang, Zhikai Liang, Lingyun Yi, Tao Jiang

"In this study, reduction of iron ore pellets was carried out at 800-950°C by simulating the atmosphere of typical coal gasification gas. The effects of temperature, gas composition and reduction degree on swelling were investigated respectively. Reduction degree was obtained according to the weight loss records. And volume changes of pellets during reduction were evaluated by infrared photography. Results showed that the pellet swelling increased with temperature and decreased slightly with hydrogen content in the reducing gas. The swelling peaked when reduction degree reached about 40% and then decreased to be stable finally. The microstructures of pellets during reduction were examined by reflected light microscope and relatively rational explanations were proposed for their swelling behaviors.PrefaceDirect reduction iron is an important and indispensable raw material for high-purified and high-quality steel in the electric furnace smelting. Gas-based shaft furnace direct reduction process has very strong competitative ability; however, this technique requires natural gas as reducing agent, so its development has been restricted by gas source and area. Compared with gas-based reduction method, coal based reduction method has the disadvantages of higher production cost and lower productivity. In China, coal resources are abundant and coal gasification technology is mature, and the development of coal gasification shaft furnace direct reduction process is promising. [1] The gasification methods of fixed bed method (Lurgi method), fluidized bed method (Undok method), airflow bed method (Texaco coal water slurry method and Shell dry powder coal method) have been put into use successfully. These syngas generated by different methods can meet the actual production requirement of shaft furnace. However, the compositions of the effective reduction gas in the syngas are quite different. The ratios of hydrogen and carbon monoxide (H2/CO) of Undok or Shell coal gas, Texaco coal gas and Lurgi coal gas are 0.4, 0.6~ 1.0 and 1.6~2.3, respectively. [2] In the coal gas direct reduction process, the swelling behavior of iron ore pellets is various due to the differences of the gas composition, reduction temperature and reduction degree, and it seriously affects the normal operation ofDRI production. [3-9] Therefore, the research on the swelling behavior and its mechanism of iron ore pellets in direct reduction were carried out in this paper."

Jan 1, 2013

By G. Kleyn

"Sub-standard practices and their adverse impact on safety performance remain a challenge in the South African gold mining industry. The purpose of this study was to investigate the root causes of sub-standard practices and the effect on safety performance in South African gold mines. The focus of the study was on the underground production operations at a gold mine in the Free State. The study consisted of three parts: a personal investigation into the causes of sub-standard practices at the mine, a comparison with the results of a cultural study performed at the West Wits mines, and a behavioural survey.The studies described in this article yielded similar results in terms of the key drivers behind sub-standard practices. It was found that substandard practices had a number of causes, and the origin lies within the habits, attitude, and behaviour of employees. Current methods of addressing sub-standard practices and improving safety performance were found to discourage employees from performing work safely and according to procedure. It was concluded that the lack of critical behavioural habits for the given work environment and job title could possibly be the primary reason for the occurrence of sub-standard practices. IntroductionSince the implementation of the Mine Health and Safety Act, 1996 (Act 29 of 1996) and the Mine Health and Safety Regulations, the South African mining industry has been striving to improve health and safety performance and has placed great emphasis on adherence to mine standards.The Act requires employers in the mining industry to report accidents, incidents, and dangerous situations to the Regional Principal Inspector of Mines in their area. The data provided by employers is captured and analysed by the South African Mines Reportable Accident Statistical System (SAMRASS) and made available for public viewing (Department of Mineral Resources, 2011).A review of the national mine-related accident statistics shows clearly that the South African gold mining industry has improved its safety performance markedly over the past decade, but is still facing major challenges (Figure 1). These include meeting the Mine Health and Safety Milestones (Department of Mineral Resources, 2011)."

Jan 1, 2016

By Lívia Silvestre Andrade

Uma das rotas mais importantes de produção do Fe-Nb para aplicações siderúrgicas é a aluminotermia. Para que o processo seja eficiente, é necessário projetar adequadamente a escória, para garantir a mínima retenção de metal na escória e reduzir as perdas, assim como determinar a carga da aluminotermia considerando os balanços de massa e de energia. Neste trabalho, os efeitos das adições de CaO e CaF2 sobre as características das escórias do processo são determinados através da termodinâmica computacional. Um balanço de massa e um balanço de entalpia são formulados, de modo a verificar se as quantidades dos diversos materiais adicionados são adequadas e se as temperaturas de fim de processo são razoáveis. Verifica-se que, a partir de uma carga hipotética formulada, há espaço para melhorias importantes balanceando-se corretamente as adições de CaO e CaF2. Além disto, verifica-se a influência do teor de Mg contido como impureza no Al empregado como redutor, observando-se que seu efeito é bem menos significativo do que inicialmente esperado por diversos operadores.

Oct 30, 2017

This paper describes the results of a laboratory study on the upgrading of Algoma siderite by the amine flotation of silica and silicate gangue. The experiments indicate that a virtually complete removal of silica is possible in a rougher flotation con-ducted in tap water at natural pH, without prior desliming of the ore. Grinding considerably finer than the apparent liberation size is essential for maximum silica rejection. A cationic collector, Aeromine 3037, gave best results when used in combination with a modifier. Of the several modifiers tested, a Dutch potato dextrin, Dextrin 4356, was found to be the most effective. Both iron recovery and the grade of the final iron product are enhanced by floating the pyrite contained in the ore prior to the amine flotation of the silica, and by scalping the magnetics from the silica concentrate. F OR over twenty years, the Algoma Ore Properties Division of The Algoma Steel

Jan 1, 1963

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018