Search Documents

By G. A. Brady

Laboratory tests were conducted to determine the technical feasibility of separating anthracite particles from a water-anthracite slurry by atomizing the water and removing the resulting mist in an air current. Products containing 21 percent or less moisture were obtained from slurries made with minus 60-mesh anthracite. Typical recoveries ranged between 67 and 79 percent of the feed when the slurries were atomized in air currents with velocities below 70 ft/min.

Jan 1, 1967

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By J. M. Dahl, L. H. Van Vlack

STAFF: Editor, Gerhard Derge Associate Editor, Paul G. Shewman Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Post-President; Harold B. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. B. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of monuscripts is under the supervision of the following Publications Committees: Extractive Metollurgy Division: R. E. Grace, Chairman; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Healy, T. A. Henrie, R. D. Holli-day, C. E. O'Neill, C. S. Sami s, A. W. Schlech-ten, and Charles Shull . Iron and Steel Division: R. D. Pehlke, Chairman; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Tuckdogon, L. H.Von Vlack, and J. M. Uys. Institute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Chairman; M. R. Achter, G. F. Bolling, J. O. Brittain, G. P. Conard, II, L. A. Girifolco. G. T. Hahn, J.P. Hirth, L. Himmel, G. T. Horne, George Krauss, C. F. Leitton, Jr., J. D. Livingston, R. D. Monning, H. M. Otte, S. V. Radcliffe, R. E. Reed-Hill, H. C. Rogers, O. Sherby, M. T. Simnod, G. R. Speich, E. A. Steigerwold, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Walton, H. W. Weart, W. W. Webb, and D. WiIsdorf. Published monthly by the American lnstitute of Mining, Metollurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York, N. Y. 10017. Telephone PLAZA 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1965 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustrial Arts Index, and Chemical Abstracts . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 233, Number 1.

Jan 1, 1965

By Marvin L. Whisman

Several parameters controlling the reproducibility of tritium determina¬tion in organic compounds by liquid scintillation counting were evaluated by the Federal Bureau of Mines. These included optimum volume of scintillator solution for maximum counting efficiency, reproducibility of counting a sealed commercial standard and comparison with duplicate counts on laboratory-prepared samples. The error introduced by using microliter pipets, optical differences in counting vials, reproducibility of counting organic samples where quenching is a factor, reproducibility of counting laboratory-prepared samples with an added internal standard, optimum ratio of internal standard activity to sample activity, effect of sample volume upon counting efficiency, count rate at which coincidence losses become apparent, and reproducibility of organic compound radioassay by the standard addition technique are outlined. From the evaluation of these parameters, a technique that can be applied routinely to organic compounds containing tritium has been established, and details are included in this report.

Jan 1, 1961

By Wightman D, Hoyle M. W H, Peters W. S

The Radio Hill nickel-copper deposit is located 30 km south of Karratha. It is a new discovery in an area where similar mineralization had been previously discovered at Mt. Scholl and Ruth Well. Radio Hill is the first massive Ni-Cu sulphide deposit of economic significance to have been located in the Western Pilbara.Preliminary studies indicate that the sulphide mineralization occurs within gabbros, pyroxenites and peridotites of a basic igneous cumulate layered sequence. Primary sulphides have been subsequently remobilized and concentrated as stringer and massive mineralization. This is tentatively attributed to the intrusion of a further gabbroic body.The deposit appears to be of the gabbroic association type with a Ni:Cu ratio varying from 1:4 in the outer parts of the mineralized envelope to 1:0.9 towards the central zones. In drill core observations, chalcopyrite surrounding pyrrhotite was noted in many instances. Drilling has so far delineated a body developed over a strike length of 600 m and a horizontal width of up to 25 m. The mineralization plunges 20° to the southwest with a southerly dip varying from 75° in the west to about 20° - 30° in the east.The deposit is a leaf-shaped ore zone, plunging southwest from a vertical depth of 17 m in the north to 300 m in the south. The massive sulphides occur as lensoid masses within this zone. A geological resource of up to 2.5 million tonnes at 1.5 per cent Ni and l.4 per cent Cu is indicated.The predominant sulphides are pyrrhotite, chalcopyrite and pentlandite, with significant cobalt, platinum group metals and gold. Tellurides of Pd, Bi and Pb were detected by scanning electron microprobe within the pyrrhotite and other trace metals include Zn and native tin. Massive magnetite is sometimes associated with the massive pyrrhotite intersections.A test on one composite massive sulphide sample showed that pyrrhotite is present mainly as the non-magnetic hexagonal variety and only 10 per cent is present as magnetic monoclinic pyrrhotite.The deposit has no surface expression and its identification was based mainly Oil drilling targets generated by geophysical methods. No secondary minerals have been observed in association with the primary sulphides, even though the deposit is only 17 m below surface in the northern part.

Jan 1, 1987

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.' The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By Milton H. Fies

Although pig iron from iron ore and red cedar charcoal preceded the mining of coal by many years, for tradition says that Alabama iron was used to shoe the horses of Andrew Jackson's soldiers, coal was not produced until 1830. In that year, coal was mined in Tuscaloosa County, in the vicinity of what is now the University of Alabama, and shipped on flat boats (obviously during the wet season, for there were many shoals) down the Warrior River to Mobile. About that time, the first railroad, the Decatur & Tecumseh, was being constructed in northern Alabama to overcome the obstructions to freight traffic caused by the now well-known Muscle Shoals in the Tennessee River. This railroad was patterned after a railroad at Mauch Chunk, Pa., which was used for hauling anthracite from the Panther Creek valley. The Alabama railroad, which required about four years to complete, was 46 miles long and was used solely for the transportation of cotton. Although it was a failure, it demonstrated the practicability of the undertaking, and the succeeding railroads, which were begun in 1834, 1848, 1852, and 1853, added immeasurably to the development of the coal resources of the state. Between the years 1830 and 1860, practically all the coal mined in the state was dug from the outcrop near the river or from the river beds, and shipped by boat to Mobile. Transporting coal down the Warrior River was an undertaking of great risk, required much skill, and frequently had heavy losses. It is recorded that this coal was sold to the gas company in Mobile in 1844; it was most likely mined from the Black Creek Seam. In 1914, on the completion of Lock 17, the Warrior River became a navigable stream from 9 miles above Cordova, Ala., to Mobile and offers a great opportunity for the future development of the coal resources of the state. Coke for foundry use was first made in Alabama in 1855. It was 21 years later, however, in 1876, that pig iron was made from Alabama ore with Alabama coal.

Jan 1, 1925

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

By R. Tervo, G. Ellie

"Automated information systems are being developed very rapidly in Europe. In France, Belgium and West Germany, more than 70% of the coal production is controlled by these installations. Information on both product ion and the mine environment is produced. For example, at one mine in France the system records the operating times of the compressors and of the refrigeration pumps, counts the number of coal cars passing the unloading point, and controls the principal conveyors and the loading /unloading of the storage bins. In addition, the ventilation air velocity, the methane content and the carbon monoxide content in the return air entry are recorded; an alarm is triggered and the current to the conveyors cut when the gas content exceeds a critical level. The recorded information is used at four levels: (1) for immediate action, (2) for daily reports, (3) for monthly reports and (4) for long-term studies. For example, when any conveyor is stopped for more than 10 minutes, the system controller immediately telephones to learn of the reason. At the end of a shift, the load factor of the conveyors is computed; then monthly an analysis of the causes of low load factors is made. The presentation describes in detail the system that has been installed in more than 20 mines in France."

Jan 1, 1973

By Robert P. Stevens

It is important for a refractory supplier to make systematic petro-graphic examinations of products which have been in service in the furnaces and kilns of customers. The petrographic examination of refractory service samples involves the microscopic study of polished and/or thin sections, supplemented by electron probe microanalysis, as well as the bulk chemical and XRD analysis of zones in the samples. The evolution of the A. P. Green Refractories Company petrographic laboratory is described, and the application of petrographic methods is illustrated in the examination of service refractories from a Portland cement rotary kiln and an AOD stainless steel vessel. The objectives of such studies are to assist the customer in the solution of his refractory problems, and to accumulate data which are of use in the design of improved refractory products.

Jan 1, 1981

[ ] DISCUSSION F A LORIA*-The method of testing gun steel for resistance to surface cracking described in this paper was restricted to the examination of small, rod-shaped specimens The writer would like to point out the importance of other factors in producing defects in forged and bored gun tubes which would not be apparent in this investigation because of the nature of )he test Actual section size would accentuate the possibility of internal wall (bore) defects arising from unequal expansion between the internal and external wall surfaces on firing, resulting in internal tearing Checks and tears on the inside walls arise from internal tensions and nonuniformity on cooling, but the internal tearing can be reduced by using alloys of low expansion and of good thermal conductivity so as to reduce the difference between the outer and inner wall surfaces Also, the possibility of the location of inclusion segregates within a machined gun tube becomes more likely than in a small test specimen The effect of these nonmetallics on gun life and performance is evident when one realizes that the inclusions are soft yet brittle They reduce the amount of plastic deformation which can take place before cohesive failure occurs Once localized fracture has occurred at the position of a chain of these inclusions, a sharp notch (crack) is formed which produces stress conditions more favorable to cohesive failure than to plastic deformation These cracks aid erosion by providing channelways for the explosive gases, eventually leading to the tearing out or spalling of blocks of metal Oxidation of the surface may be partly responsible for the change in the surface of gun steel during firing observed by the author The appearance of burn on the surface is an indication that high temperatures were reached on firing, resulting in a slight oxidation of the surface Since the color of the oxidized film depends on both temperature and time, a higher temperature is required for a given color to form when it is caused by explosive heat, which acts for only an extremely short time at a given spot, than when it is caused by ordinary tempering The cross section of the gun steel specimen, Fig 16, illustrates that the repeated firing temperatures were high enough to cause

Jan 1, 1948

By Nancy Redhead

El buen funcionamiento de los equipos de una fábrica depende de la energía eléctrica. Si ocurriesen problemas con esta, se resuelven con tecnologías convencionales como la utilización de bancos de condensadores, filtros activos, UPS, estabilizadores de tensión y protectores de sobretensiones. Sin embargo, el riesgo de utilizarlas es que algunas veces son incompletas o no son compatibles. En ese sentido, el presente texto plantea una nueva tecnología utilizada en otros países que corrige los problemas eléctricos de forma completa y segura. Este un sistema automático completo de ahorro de energía y de la calidad de la onda eléctrica que está dotado de un microprocesador y analiza el voltaje, corriente, factor de potencia y armónicos. Asímismo, permite recuperar la energía perdida para luego filtrarla y devolverla a la red -al tiempo que se agrega una carga adicional sin necesidad de incrementar el tamaño de los transformadores o conductores.

Apr 1, 2013

By Homer E. Harris

As a result of the enactment of the Federal. Coal Mine Health and Safety Act of 1969 1, the Department of Health, Education, and Welfare (HEW) has been carrying out research in the "field of coal mine health". The National Institute (formerly Bureau) for Occupational Safety and Health (NIOSH) was designated the agency within HEW to be responsible for such research activities. One of the early programs sponsored by NIOSH was undertaken by Eastern Associated Coal Corp., with the Harvard University School of Public Health participating as a subcontractor to Eastern. This program on Coal Mine Respiratory Protective Devices, which started on June 30, 1970, had five major objectives as follows: a. to determine current status of respirator usage with respect to duration and frequency, types. and maintenance b. to determine acceptability ( and reasons therefor) of currently used units c. to determine protection factors provided by respirators worn by working miners d. to make recommendations on ways to improve existing units, or on research needed to develop new types of respiratory protective devices for coal miners e. to provide recommendations to mine management on more effective use of respiratory protective devices

Jan 1, 1973

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By Robert A. Wilson

Los primeros pasos básicos para determinar los valores reales y los minerales concernientes, que son la base para las pruebas metalúrgicas, son presentados en este capítulo. A continuatión, eligiendo el proceso o los procesos indicados para el tratamiento de un mineral, son expuestos los temas. Todo esto es seguido por los procedimientos utilizados, el resultado de los cuales indicará la viabilidad para el tratamiento. Estas pruebas de procedimiento han sido desarrolladas, utilizadas y de probada efectividad en laboratorio con evaluaciones relativas al procesamiento de la planta. Los procedimientos especiales y poco comunes se encuentran fuera de la finalidad de este capítulo. La evaluatión de los resultados de las pruebas y su incorporatión dentro del flujograma preliminar y final para el diseno de la planta son temas igualmente expuestos. El valor de un flujograma, con balances de material y agua para el diseño de la planta, es asimismo mostrado.

Jan 1, 1982

By George M. Fowler

THE Tri-State district, as outlined in this paper, refers to the entire mineralized area in southwestern Missouri, southeastern Kansas and northeastern Oklahoma (Fig. 1). The part of the district in Missouri and near Galena, Kans., is still sometimes referred to as the Joplin district (Fig. 2). The Picher-Miami area is that part of the Tri-State district located contiguously in Kansas and Oklahoma in the vicinity of Baxter Springs, Picher and Miami. This paper is confined almost wholly to the ore deposits of the Tri-State district and particularly to the Picher-Miami area. Our study of the ore deposits of this district dates from late in 1925 (by Fowler) and early in 1927 (by Lyden) to the present. Our work has been confined almost entirely to the search for ore for numerous companies and individuals. It was not possible for us to undertake numerous highly interesting investigations which presented themselves but which would not immediately help in finding ore. We particularly refer to the general structural geology of the Ozark uplift, the genesis of the ore, and other problems of a similar nature. The local and general structural problems of the district are being solved gradually as the work progresses. The factors that control the loci of the several orebodies are evident. This paper is based almost exclusively upon our own observations. Most of the important mines in the Picher-Miami area were studied in detail. A map (Fig. 5) is included which shows this area and the properties we have examined to date. When it was convenient we visited, studied and compared structural relations in numerous mines in states outside the district. Some of these observations are noted in this paper.

Jan 1, 1932

By Victor Munoz, Jorge Oliva, Gonzalo Marias

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth.

Jan 1, 2019

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By Alexander Squire

One of the principal factors that have contributed to the hesitancy of design engineers to use metal-powder parts is the difficulty experienced in the determination of the mechanical properties of compacted components. Because standard test methods cannot usually be applied in the inspection of such parts, and because adequate special test methods have not been developed, it has been considered desirable to investigate the methods that are applicable. These may then be included in specifications for metal-powder materials and components in order that the design engineer may be assured that the subject parts possess the desired mechanical properties for satisfactory performance. It is known that direct relationships exist between usually nonmeasurable properties as tensile strength and elongation and shear strength and the angle through which compacts may be plastically deformed before fracturing. These correlations are valuable in the inspection of specific parts, but it is necessary to set up standards before they may be satisfactorily employed. Apart from the use of correlations, the number and character of the inspection methods that are applicable to almost all powder parts is limited to three—chemical analysis, density, and hardness. The last of these may or may not be a pertinent characteristic, since the indentation hardness of many powdeied-metal materials is so low as to have little significance. It is, however, occasionally desirable to use hardness measurements as an indication of the uniformity of the structure of pieces of a given type. Chemical analysis reveals very little about the physical properties of metal-powder compacts, since the unpressed powder is usually of a composition almost identical with that of the finished pieces. Density determinations are simple to perform and have the advantage of being nondestructive in character. If the dimensions of a machine part are known (and usually they are), the average density may be determined by weighing a given number of pieces and dividing by the calculated volume of the parts. More accurate measurements may be made by the water-displacement method. It is recognized that mechanical properties of metal-powder materials are related to their density, but usually these relations are determined for only one type of powder, processed under a given set of conditions. Comparisons of the pioperties of compacts formed from different types of powders are made on the basis of compacting pressures instead of density, and for this reason the results obtained by using powders of different types appear widely variant.

Jan 1, 1947

By M. C. Ethier, A. L. Laramie

"The Granisle and Bell Copper mines were officially put into production in 1966 and 1972, respectively. The Granisle Mine was purchased in late 1979by Noranda and the two operations were amalgamated as one division. Both mines were closed in 1982after sustaining heavy financial losses during a period of low copper prices beginning in 1981.This paper describes the resumption of operations at the Bell Mine in 1985 after its shutdown period of three years and the dramatic and sustained improvements in productivity and efficiency realized as a result of a commitment by employees and management to the application of Participative Management and Employee Involvement principles. After a general description of the effects of such a philosophy on the operation as a whole, and a comparison to the operation&apos;s last full year as a producer, it deals with the practice of this philosophy in the maintenance department at the Bell Mine and the superb results realized.IntroductionThe Bell Copper deposit was discovered in 1963 and came onstream as a 10000 ton s per day open pit mine in the fall of 1972. Identified reserves at that time were 46 million tons of ore containing 0.50% copper. The mine shared facilities of the townsite of Granisle with the nearby Zapata-Granby mine which had established the community six years earlier.Because of easy grinding ore and improvements to milling circuits, Bell&apos;s throughput rate was increased to 17 000 tons per day by the late 1970s. In the open pit, improvements resulted in mining of additional reserves with higher stripping ratios. At startup, a half ton o f waste was mined for every ton of ore processed.By the end of 1982, with 48.2 million tons already mined, the Bell Mine had identified additional mineable reserves of 39.4 million tons containing 0.52% Cu.In November 1979 the Granisle Mine was purchased from Zapata-Granby. The two mines, with a total of 700 employees, were operated under common management as the Babine Division until 1982 when low copper price s forced the closure of both for an indefinite period.The outlook for copper prices remained bleak and only 50 people were retained on the payroll to maintain the two plants, most of them working on a part-time schedule.The population of the Village of Granisle dwindled from over 1500 inhabitants to under 500, as people moved away to seek other employment.Prior to the shutdown, the Bell Mine employed 370 people and pit extraction averaged nearly 50000 tons per day of which 16000 tons was mill feed, and the remainder waste. Total cost to produce a pound of copper was C$1.36 in 1982."

Jan 1, 1990