Search Documents

By Eun Duck Park

The gold catalyst supported on iron oxide was prepared from gold dissolved in aqua regia by a deposition-precipitation method and applied to CO oxidation in the absence and presence of hydrogen. Some characterization methods such as X-ray diffraction (XRD), nitrogen adsorption, transmission electron microscopy (TEM), temperature programmed reduction (TPR), temperature programmed oxidation (TPO), and the pulsed CO chemisorption with temperature programmed desorption (TPD) were conducted to explain different catalytic activities of Au/Fe2O3 catalyst pretreated at different conditions. The particle size of gold was about 10 nm for Au/Fe2O3 calcined in air at 373 and 573 K. For complete CO oxidation, the decreasing CO conversion with a reaction time was observed at low temperatures but its initial catalytic activity can be restored by a heat treatment at high temperatures. This catalyst was quite active for the selective CO oxidation in the presence of hydrogen especially at low temperatures. In the presence of hydrogen, the deactivation was significantly diminished.

Jan 1, 2006

By Lawrence W. Sott

This Bureau of Mines report presents several factors that currently enter into the design, manufacture, and testing of windows and lenses used in explosion-proof enclosures. Emphasis is also given to the sealing concepts for lenses. Criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure, rather than upon the minimum material properties of its constituents. Procedures for surface preparation of adherends are also discussed.

Jan 1, 1982

By Edwin Itzig-Heine, Daniel Traylor, Bernard Tarralle, Michael McKenna

This paper discusses the challenges associated with the design and construction of a dual-cell, “figure eight” shaped shaft in saturated, soft ground for the Northeast Interceptor Sewer project in Los Angeles. The shaft will be excavated to a depth of41 m and used to launch two EPB TBMs. The specifications required concrete diaphragm walls, embedded below the shaft invert, and a grout curtain beneath the wall. To control water pressure and basal stability without a grout curtain, wall panels were embedded deeper than required into a stiff, cohesive deposit. Details of wall panel excavation using a Hydrofraise are presented.

Jan 1, 2003

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

By Thomas E. Garnar

Zirconium and hafnium are the twin elements of the periodic table because they are always found together. They resemble each other so closely that hafnium was not discovered until 135 years after the discovery of zirconium. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and von Hevesy detected it using X-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO,) and less commonly as baddeleyite (ZrO,). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. During World War I, it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s, when Zircon Rutile, Ltd., began mining at Byron Bay on the east coast of Australia, that zircon was first used as foundry sand. Later in the 1940s, NL Industries and Humphreys Gold Corp. began production of zircon sands from fossil beaches in northeast Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties and as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by the Republic of South Africa and the United States. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, the former USSR, China, Thailand, and Brazil. The location of world zircon mines, baddeleyite mines, and undeveloped zircon ores are shown in [Fig. 1]. World production of zirconium mineral concentrates is shown in [Table 1].

Jan 1, 1994

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By H. O. Harju

Inco acquired majority interest in the nickel laterite concessions in eastern Guatemala in 1960 and, through its subsidiary Exmibal, extensively explored the deposits until 1965 to define the site for project development on the north shore of Lake Izabal. This paper outlines the exploration methods used to evaluate the Guatemalan laterite deposits.

Jan 1, 1979

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian' and others' to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,' then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß' phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß' and [-phases. The phase diagram in the ASM handbook'" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß', the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

INTRODUCTION IT is 10. years this summer since the first of the contributions which it has been my privilege to make to the working tools of the hydrometallurgist was set at work, but a full description of what has come to be known as "Dorr Machinery" has never been published in the Transactions of the Institute, and it has been suggested to me that an account of the same would prove of interest to members, although most of those engaged in cyaniding and concentration are probably familiar with it. The account which I shall give of the development of the machines must be recognized as being written from the viewpoint mainly of my own local experience and not from that of one who was familiar with the general metallurgical practice throughout the world. Most advances in any art are conceived before the time is ripe for their development and any .invention which comes into general use will usually be found to have been tried out in a crude way and abandoned more than once. If the early experimenter went as far as the Patent Office, his work may serve no other purpose than to prevent the issuance of the broadest patent to those who later may develop a commercial process. The cyanide process in the United States early in 1904 was mainly confined to the leaching of dry crushed ores, both coarse and fine, and sand treatment of tailings from concentration and amalgamation. In the Black' hills some plants were crushing in cyanide solution, leaching sands and handling the slime by the well-known decantation process. Filter pressing, in use for some years in Australia,had been tried in several places in this country and the Moors process had been abandoned at Mercur after' a short run, but was doing good work at the mill of Lindbergh, Dorr & Wilson, at Terry, and being installed at Bodie and the Liberty Bell. A general feeling, however, still existed that, slimes were to be avoided when possible, on account of the losses in treatment and the difficulty of making a good leaching product when they were present in large amounts, especially when the crushing was done in cyanide solution.

Jan 8, 1914

By John T. Dieckmann

This report documents the work performed and the results obtained in a 2-year development of a Mobile Inert Gas Generator for use in the Bureau of Mines Remote Sealing System for fighting underground coal mine fires. The performance requirements of an inert gas generating system for the Remote Sealing System were clearly established. A thorough review of seven possible system designs meeting these requirements was conducted. An air cooled, distillate oil fired combustion type inert gas generator was selected for further detailed design, hardware fabrication, and performance testing. The Inert Gas Generator constructed under this program has been thoroughly performance tested and has been operated in the field for approximately 200 hours. The system has met or exceeded all important performance requirements. The system was used in the fire fighting efforts at the Bethlehem Mines Corporation Cambria Division Mine 33 fire and contributed to the successful containment of the fire. The system was also employed in the demonstration of entire Remote Mine Sealing System at the Jenney Mine in the fall of 1978. The system is currently avail-able for fighting any future underground coal mine fires.

Jan 1, 1979

By J. D. Dixon

The Bureau of Mines investigated the principles of support-rock interaction, based on structural matrix methods which permit mathematical formulation of the problem and computer solution. The principles are given under two main sections: the first discusses the idealization of the tunnel support structural system for matrix analysis; the latter discusses the analysis procedures necessary for carrying out the solution. A general frame matrix computer program and a medium-size computer should be sufficient for carrying out the procedures involved. The example problem consists of a circular tunnel support which is subjected to a uniformly distributed vertical load, Three wall thickness-radius ratios are studied in combination with four support-rock modulus ratios. This problem illustrates the main procedures of the support-rock interaction analysis involved, and examination of the results reveals the influence of the relative rigidities of the support and the rock.

Jan 1, 1971

By D. Fodor

In Romania, there are significant lignite and brown coal reserves hosted by different regions of the country. The most important lignite bearing zone of the country situated in the North ? West part of Oltenia region and which covers a surface area of 2,500 km2 and host a total reserve of 3.0 billion tons of lignite, of which more than 95% can be exploited by open cast method. The paper deals with the existing geological and mining conditions of the zone , the distribution by mining basins and exploitation perimeters, the open cast working technologies and the economic outcomes obtained throughout the time. Years ago, for the improvement of the economic situation as a whole and in each unit, a large production reorganization, technology update and modernization process was started up. There are described the rehabilitation measures of the technological lines and modernization of the equipments of the production flow-sheet, measures developed at present, too and which will still continue in future. There are mentioned the equipments considered, the components under modernization and the economic outcomes obtained so far. At the end of the paper there are presented the future actions for the equipment modernization and perspectives of the lignite deposit exploitation to meet the national economy requirements of solid fuels.

Aug 1, 2013

By A. S. Dawson

Introduction The purpose of this paper is to discuss, in a general way, the application of geological principles in the exploration for, and development of, deposits of industrial minerals. Mention of geological factors pertaining co specific minerals will be by way of illustration only. Since many prospectors are little acquainted with the geological setting and mode of occurrence of deposits of these minerals, some prospecting possibilities in the field will be pointed out. Geology is a tried and proven tool in the search for and exploitation of metalliferous deposits and of oil and gas fields, but, so far at least as Canada is concerned, only very rarely has a directed, intensive search been made for deposits of industrial minerals. Examples might be cited, however, where, in other countries, such investigations have yielded rich rewards. Thus, development of the vitally important potash deposits of New Mexico was the result of a deliberately planned programme of geological investigation, first by United States Government agencies, and later by private interests. War or the threat of war, or peace-time industrial expansion, can render concentrated exploration for specific minerals desirable or even essential. Such exploration is, primarily, a geological problem. Admittedly, there is in general less scope for the application of geology in the search for, and development of, deposits of industrial minerals than of metalliferous minerals, oil, etc. Where the latter are concerned; the objective of exploration is to find a material that is valuable, within broad limits, no matter where it is located or how it occurs. The unit value of the material is limited only by the amount of the valuable constituent in the formation- its possible upper limit is tremendously high. On the other hand, many industrial minerals constitute in themselves 90 per cent or more of the formation- their amount cannot increase and their unit value is commonly low. Moreover, for commercial exploitation, the deposit must, in general, be reasonably close to markets or to plant or other facilities for processing the raw material, since, owing to its low value, this cannot be transported any great distance. As a consequence, intensive geological search for and investigation of such deposits has been restricted to industrialized areas. Obviously, however, it is good insurance for any operator to understand the geological background of his deposit, particularly in the case of new developments.

Jan 1, 1949

By Gregory L. M, Phillips G. N

Although it has long been recognised that there is a diversity of minerals associated with Victorian gold deposits, the degree to which this mineralogy is systematic or haphazard has remained uncertain. Recent work by the authors and students under their supervision permits a sharp delineation of the boundaries between different mineralogical domains, and these are interpreted in terms of recent rapid advances in Victorian tectonics, and the regional framework of Victorian gold geology described in Phillips and Hughes (1996).

Jan 1, 1997

By Frank Clemes Smith

The study of the so-called refractory gold-ores of the Potsdam sandstone, ores which are probably of wider occurrence and of much greater economic importance in the Black Hills than is generally supposed, has led the writer to formulate in the present paper some of the results obtained in the course of a special examination of these particular ores, conducted at the State School of Mines at Rapid City, So. Dak. Various circumstances have interrupted the work, and it will easily be seen that relatively little has yet been accomplished; but it is hoped that this little may be of sufficient interest to justify a later supplement. Tellurium, discovered by Muller von Reichenstein in 1781, is generally classed as a very rare metal; it is further mentioned by one of our late writers as " of comparatively little importance," and as obtained from its ores by a " complicated process.'' Concerning its rarity, we have some trustworthy evidence below. Its commercial importance, particularly in connection with electrical appliances, has been passed upon by Mr. Edison ; * and it is certain that, in some metallurgical processes for the treatment of gold- and silver-ores, it may be saved as a byproduct at a relatively reasonable expense. The importance of tellurium as a mineralizing agent is emphasized by the remarks of one of our leading metallurgists,jwho, in his own practice and by a wide series of experiments, has found its occurrence to be much more general than has been supposed. Recently the same writer has discussed the occurrence of tellurides and oxidized tellurium compounds in the gold-ores of Cripple Creek, Colo., and in those of the Black

Jan 1, 1897

By G Richmond, J R. Glen

Western Metals Mt Gordon Operation is a copper mine and processing plant situated 120 kilometres north of Mt Isa. The unique Mt Gordon copper process utilises a whole of ore acid/ferric pressure leach to produce copper cathode from the Esperanza massive sulfide copper orebody. Esperanza ore contains chalcocite, covellite and minor chalcopyrite hosted in a massive pyrite matrix. These ore stocks will be depleted in late 2003. Recently the process circuit has been upgraded to allow the treatment of lower grade Mammoth ores. These include the installation of a ball mill to complement the existing SAG mill, a single stage rougher flotation circuit and a tailings thickener. The leach bleed neutralisation plant was also upgraded at this time. Commissioning of these new circuits occurred in March 2003 and involved all the challenges of ensuring current production levels were successfully maintained while new process steps were incorporated into the whole circuit. This paper explains the background flow sheet of the patented Mt Gordon process and the reasoning behind the enhancements required for an already successful copper leaching circuit. Included are discussion of the influences of the new ores on individual process components such as comminution, leach chemistry and solid/liquid separation. Longer term ore processing options are also discussed.

Jan 1, 2003

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

In an extremely competitive mining industry, onsite experience is a big advantage. Mining education at the universities is mostly focused on theoretical studies without a possibility of practical training in mining sites. Hence, experimental mines suitable for practical education are needed to provide a platform for systematic research and education in industrial scale and for training in real mining conditions. Yet, this kind of mine sites is rare worldwide. Thus, a new educational research project, namely MINETRAIN is introduced in this paper evaluating the transition of the Pyhäsalmi mine in Central Finland from an active base metal mine to a research, educational and training underground facility. The uniqueness of MINETRAIN compared to other test mine programs is that the existing state‐of‐art infrastructure in Pyhäsalmi enables research and training facilities among all disciplines related to the overall mine value chain. Though all the above sound interesting in the context of research and education purposes, in practice Pyhäsalmi will have to become an experimental mine that can be sustainable in the future. Accordingly, a prefeasibility study is being conducted and some preliminary results are presented in this paper. INTRODUCTION Despite being a field of studies that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world; consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited to none, while the only contact that undergraduate students have with mining operations during their time of studies is usually through short-time internships or visits in the context of educational trips. Yet, real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes, and thus understand the whole picture of mining operations. Indirect practical training is also possible nowadays that technology is shifting from mechanical to digital, and the use of virtual reality -in the context of Mining 4.0- can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al, 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other and especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers. Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and know-how could be developed and/or enhanced are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.

Jan 1, 2019

By James Johnston

Synopsis.-A description of the working of the mills of this company and the metallurgical practice in vogue, by which a remarkably. complex silver ore, averaging 54 oz. of silver per ton (run-of-mine ore), is treated to give a 95.66 per cent. extraction. The main features of the, processes are: The cyanide amalgamation of the high-grade ore. The cyanide treatment of the low-grade ore, after extremely fine grinding and close classification, in a caustic soda solution. The use of a wet desulphurizing process to break up refractory silver minerals. The substitution of aluminum dust for zinc dust as a precipitant. The recovery and shipment of over 13,000,000 oz. of silver in bullion at. 997 to 999 fine since this metallurgy was inaugurated, about 2.5 years ago. On the completion and successful operation of the mill to treat their . high-grade ore,1 the Nipissing Mining Co., under the general management of R. B. Watson, started a series of investigations of the possible treatment of the low-grade ore by the cyanide process, so that they would be in a position to market only silver bullion. These tests were run in July, 1911, on a large scale, by G. H. Clevenger, on an average mixture of Nipissing ore. The results obtained by a partial amalgamation followed by cyanide treatment gave an extraction varying from 90 to 93 per cent. and were sufficiently encouraging to warrant Charles Butters, the company's Consulting Metallurgist, in recommending that the new low-grade ore mill under contemplation should be a cyanide mill, instead of a concentrator. The cost of such a mill, capable of treating 200 tons per day, to obtain a 90 per cent. extraction at a working cost of $3 per ton of ore treated, was estimated at $250,000.

Jan 1, 1914