Search Documents

By Charles B. Kenahan

Vanadium is subject to only light corrosion in phosphoric acid at temperatures up to 60° C. and has a moderate corrosion rate in this acid at 100° C. It is relatively corrosion resistant in sulfuric and hydrochloric acids up to 60° C, but corrodes rapidly at 100° C. It corrodes rapidly in dilute nitric acid at 35° C. Vanadium is almost inert in 10-percent solutions of formic, acetic, lactic, tartaric, and citric acids; in 9-percent oxalic acid it corrodes slowly up to 60° C. and rapidly at 100° C. Vanadium is resistant to corrosion in substitute ocean water, tapwater, and in 3-percent sodium chloride and 10-percent sodium hydroxide solutions. It is readily attacked, however, by 20-percent ferric chloride, 20-percent cupric chloride and 5-percent mercuric chloride solutions. Vanadium is protected by contact with magnesium, aluminum, and steel SAE 4130 in substitute ocean water, by magnesium and aluminum in 3-percent sodium chloride solution, and by magnesium in tapwater. Vanadium protects copper in substitute ocean water. When vanadium and stainless steel are coupled in sulfuric acid solutions, both metals are usually unaffected by contact, whereas the corrosion rate of titanium in sulfuric acid is greatly reduced by contact with vanadium.

Jan 1, 1962

By James F. O'Neill

Brown iron ore deposits in Quitman County , Ga . , were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia , Department of Commerce , and the University of Alabama . Ninety- one holes were drilled , having an aggregate footage of 2,188 feet ; seventy- one holes penetrated 248 feet of iron mineralization . Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden . The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese . Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current log washer practice , with the use of a 1 /8 - inch screen , and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese . The weight recovery obtained was 14.7 percent . Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade . The average weight recovery was increased to 18 percent with a 10 - mesh screen and 22.8 percent with a 20 - mesh screen . Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200- mesh screen . Clay was prominent in micron - size slimes . Silica was deleterious in the minus 20 - mesh size .

Jan 1, 1965

By Djalma Souza, Jean Igor Margem, Sergio N. Monteiro, Frederico M. Margem

Synthetic fibers have been used for many years to attend the demands required by the technologica lfields. However, the use of them has been questioned due to the impact on the environment. In this way, the natural fibers have received extensive attention, in particular hybrid fabrics of natural fibers to reinforce environmentally friendly polymer matrix composites. Thus, the present work has the objective of evaluating and comparing the mechanical properties of composites formed by hybrid fabric with 70% Malva—30% Jute in epoxy polymer matrix. The tests carried out are the Charpy and Izod Impact Tests, with specimens of 10, 20 and 30% in volume of hybrid fabric environmentally friendly into polymer matrix composites at room temperature. The 30% samples had the best results, functioning as an efficient reinforcement.

Mar 1, 2018

By Phillip A. Armstrong, Charles A. Lewinsohn, John H. Gordon

"This paper describes the opportunity offered by employing systems based on mixed conductive ceramics, in particular, ceramics conductive to oxygen ions and electrons, in reducing CO2 emissions from metallurgical production. Membranes based on these mixed conducting properties enable commercial viability of several attractive metallurgical processes. One of these processes utilizes modular, ceramic-membrane structures for the generation of pure oxygen, in tonnage quantity. The membrane-based systems offer significant capital savings and operating efficiencies in various metallurgical processes. The current status of this technology is summarized below.IntroductionCryogenic oxygen supply technology is currently the state-of-the-art for applications that require large quantities of oxygen (hundreds to thousands of tons per day). Cryogenic technology, however, requires substantial energy inputs and, hence, adds significant costs and emissions to processes. Furthermore, cryogenic oxygen supply technology is mature and there is relatively little potential for substantial capital cost reduction or efficiency improvement in coming decades. Non-cryogenic technologies offer a means to reduce the environmental footprint and cost of the oxygen supply facility in various applications.Ion Transport membranesCommercially available non-cryogenic air separation technologies, such as adsorption-based and polymeric membrane-based methods, do not afford the economies of scale that the cryogenic distillation enjoys. Therefore, industrial gas industry researchers began searching for alternatives to the relatively inactive and unselective polymeric membrane materials available. In the late 1980’s, Air Products began developing a new class of highly selective membrane materials with exceptionally high activity for oxygen transport. The materials constitute a class of oxide ceramics, and conduct both oxygen (as oxygen ions) and electrons in the same membrane, separating oxygen from air electrochemically. Numerous detailed process economics studies have shown that, based on these ion-transport membranes (ITM’s), the cost of oxygen can be reduced by approximately one-third relative to that obtained from state-of-the-art cryogenic oxygen supply technology, through a combination of capital cost savings and efficiency improvements. [1,2,3]"

Jan 1, 2008

By Arthur E. Morris

Fifty years ago when Professor Yazawa began his career, the field of process simulation and modeling was in its infancy. Since then, tremendous progress has been made in our ability to model metal production flowsheets from mine to refined metal. This progress has come about by parallel developments in basic understanding of process chemistry and in computational techniques, This paper will review the progress made in process understanding and modeling in lead, zinc, and copper metallurgy from its inception to the present, and the role of Professor Yazawa's work in furthering this progress. Specific examples will be given for the sintering of lead concentrates, slag fuming, zinc concentrate roasting, flash smelting of copper, and pyro-extraction of zinc. Factors limiting further progress will be described.

Jan 1, 2003

By Kota Nakashima

Residues from titanium smelting tend to contain scandium. The scandiumis discarded because no suitable process exists for its recovery from the residue. Valuable-metal recovery from discharged residue is critical for environmental conservation and to achieve a sustainable society. Since 2015, JXNippon Mining&Metals has been developing a process for scandium recovery from the residue of a titaniumsmelting process. The process consists of the following steps: scandium concentrating by classification or neutralization, selective scandium leaching, impurity removal by neutralization, solvent extraction of scandium by using D2EHPA, purification, and roasting. We optimized the above steps to achieve an effective process to obtain scandium oxide (Sc2O3). In this paper, we introduce results from the bench-scale test of the scandium recovery flowsheet developed by JX Nippon Mining & Metals.

For the year ending February, 1920 PRESIDENT HORACE V. WINCHELL MINNEAPOLIS, MINN. PAST PRESIDENTS PHILIP N. MOORE ST. Louis,. Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX NEW YORK, N. Y. TREASURER GEORGE D. BARRON NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 9, 1919

By Arthur E. Morris

Fifty years ago when Professor Yazawa began his career, the field of process simulation and modeling was in its infancy. Since then, tremendous progress has been made in our ability to model metal production flowsheets from mine to refined metal. This progress has come about by parallel developments in basic understanding of process chemistry and in computational techniques. This paper will review the progress made in process understanding and modeling in lead, zinc, and copper metallurgy from its inception to the present, and the role of Professor Yazawa's work in furthering this progress. Specific examples wi1\ be given for the sintering of lead concentrates, slag fuming, zinc concentrate roasting, flash smelting of copper, and pyro-extraction of zinc. Factors limiting further progress will be described.

Jan 1, 2003

By Edward Cogan

Equilibrium phase diagram studies of zirconium- rare earth metal alloys by the Bureau of Mines at its Albany Metallurgy Research Center prompted the development of a rapid gravimetric method for determining rare earths in zirconium in which the rare earths are absorbed from sulfuric acid solution of the alloy on a cation exchange resin . The sample in 10 percent H2SO4 is introduced into the column , the zirconium is eluted with 10 percent H2SO4 , and the rare earths are eluted with (NH4 )2SO4 solution and precipitated with NH4OH . A tracer technique was employed to determine the efficiency of the procedure . Y203 and europium 154 - 152 (Oak Ridge ) were added to 10 g of zirconium and taken through the entire procedure . Recovery averaged 97.6 percent on 0.002 μg europium in the rare earth fraction . Rare earths were determined in the range 0.10 to 90 percent .

Jan 1, 1964

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By Carlos R. Scherpenisse

La voladura es una de las operaciones unitarias en la extracción del mineral, donde se busca un adecuado grado de fragmentación de la roca y se reduzca el costo combinado de las operaciones de perforación, voladura, transporte y chancado primario roca, produciendo a la vez el menor daño posible en las cercanías de ésta. En este sentido, el empleo adecuado del Monitoreo de Vibraciones producto de voladuras, es una técnica que provee múltiples ventajas en términos de examinar en detalle el proceso de la voladura y conocer su eficiencia relativa, su interacción con las cargas adyacentes y en definitiva el rendimiento general del diseño. Por ello, el presente trabajo describe algunos casos de aplicación de la técnica de monitoreo de vibraciones -particularmente en Mina Subterránea y su importancia en el diagnóstico, control, modelamiento y optimización del proceso de la voladura. Asimismo, analiza su potencial en términos de alcanzar substantivas mejoras técnico-económicas, aumentar los rendimientos y minimizar los costos operacionales en esta etapa de la explotación minera.

May 25, 1998

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By Mirian Mamani

"En el presente trabajo se analiza ambos modelos basado en la información de geoquímica de rocas de varios tipos de yacimientos (epitermales, pórfidos, IOCG, skarn y polimetálicos) relacionados a ocurrencias de Au-Ag, Cu-Au-Mo, Fe-Cu-Au, Cu-Ag-Pb-Zn), y cuyas edades de formación varían entre 150 y 9 Ma (Jurásico Superior y Mioceno). "

May 1, 2008

By C. L. Clark

EVERY user of steel should ask himself whether or not he is taking full advantage of the discoveries of the steel metallurgists during the last few years, or is merely buying grades that looked to be the best five or ten years ago for various specific purposes and have since proved perfectly satisfactory in his plant. If he has not kept abreast of the times, then it is probable that something better has been developed, or something just as good that costs less. Though this article will have to do with steel for high-temperature applications primarily, marked advances have been made in steels for other purposes as well.

Jan 1, 1940

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. Cambrell and Haynes1 (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and Singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 45°. However, to date, no systematic attempt has been made to establish design criteria. In this paper, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1979

E P MATHEWSON, Disttrict 0 NEW YORK, N Y PAST PRESIDENTS EDWIN LUDLOW, District 0 NEW YORK, N Y ARTHUR S DWIGHT, District 0 NEW YORK, N Y FIRST VICE-PRESIDENT J V, W REYNDERS, NEW YORK, N Y TREASURER CHARLES F RAND, NEW YORK, N Y

Jan 1, 1923

By A Hamanaka

EGAT Mae Moh Lignite Mine in Thailand produces about 16 Mt of lignite annually from open-cut mining. The coal is used to generate 2400 MW of electricity. In the near future, however, the coal must be extracted from underground at 400 - 500 m deep from the surface. The problem is the thickness of the coal seams. There are two coal seams that are about 25 m thick with 20 - 25 m of interburden between them.In order to investigate thick seam mining systems and propose a new mining system in ultra-thick coal seams in Thailand, a joint research group was established by Japanese and Thai researchers and mining engineers in early 2009. This paper describes conventional underground mining systems and underground coal gasification for thick coal seams and discusses the applicable coal mining systems to this mine. Then, this paper proposes an innovative underground coal mining system for thick coal seam, ‘eco-friendly underground coal mining system which consists of the utilisation of flyash and CO2 storage’.

Nov 22, 2011