Search Documents

By F. H. Gilpin

SINCE Noah pitched his ark within and without with pitch, the use of asphalt in human endeavor has been increasing-for Noah's pitch was asphalt. Asphalt is a bituminous material found in nature, either pure or admixed with smaller or greater quanti-ties of mineral and non-mineral materials, or obtained by the refining of crude asphaltic-base petroleum under proper methods of control. Native or "natural" asphalts are scattered through-out the world, though the commercial value of the various deposits varies greatly, depending upon both their accessibility and magnitude and the quality of the material found. It is an acknowledged fact that such asphalts have been produced through natural causes by practically the same application of tempera-ture and pressure as are used in the modern refining of crude asphaltic-base petroleum. The best known of all the native asphalt deposits are those of Trinidad Lake in the Island of Trinidad, British West Indies, and of Bermudez Lake in Vene-zuela. Asphalt from Trinidad Lake, after refining to remove organic and some inorganic diluents, contains approximately 35 per cent, of inorganic residue, and the asphalt thus produced must be fluxed with lighter asphaltic or semi-asphaltic base oil to make it com-mercially utilizable. The refined asphalt obtained from the Bermudez Lake deposit contains from 4 to 6 per cent. of inorganic material which cannot be removed. This asphalt, also, must be fluxed to produce com-mercial products. Small quantities of similar materials are available in other locations. The best pure native asphalt' is known as. gilsonite and is mined in com-mercial quantities in the State of Utah. In numerous places in the United States, particularly Oklahoma and Kentucky, there are deposits of sand¬stone and limestone impregnated with bitumen, which are known as rock asphalts. These rock asphalts may be used, particularly in the paving industry, either as found or by slight fluxing; from some deposits the asphalt is extracted and marketed commercially.

Jan 2, 1923

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as derived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems.

Jan 1, 1974

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By Renfeng Song, Shaoyan Wang, Zhiqiang Zhang, Ke Guo

Leaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Jun 16, 2021

By Altair Lúcio de Souza

Foi implantado um software, PCT (Production Control Tool), de integração e coordenação do fluxo de dados entre os seguintes níveis de automação: nível 3, onde se encontram os dados de especificação do produto e sequenciamento de produção, e nível 2, onde se encontram os modelos matemáticos, resultados do processo, interface com medidores e rastreamento da produção. No processo de construção do PCT viu-se um grande potencial de desenvolver outras funcionalidades, devido enorme flexibilidade dessa ferramenta, como gerenciamento da produção, auxílio na inspeção de qualidade e controle estatístico do processo. Isto levou a criação de um sistema amigável de fácil utilização, utilizado tanto pelos operadores da Linha e inspetores de qualidade como também pelos analistas do processo, auxiliando na otimização da Linha de Tiras a Quente da Gerdau.

Aug 17, 2017

By Dewa Putu Agus Sudarmaja, Widi Astuti, Januarti Jaya Eka Putri, Yayat Iman Supriyatna, Himawan Tri Bayu Murti Petrus, I Wayan Warmada, Siti Nurul Aisyiyah Jenie, Ferian Anggara, Anisa Maulidia, Vincent Sutresno Hadi Sujoto, Sutijan

With the rapid development of renewable energy technology, such as electricity reserves, to store energy for electric or electric vehicles, environmentally friendly energy sources are expected to continue to be fulfilled according to mobility and stationary energy needs. Lithium is the most attractive candidate for energy storage development. The presence of lithium in Indonesia in the Sidoarjo mud content is interesting to be used as an alternative source of raw materials. During the research, sulfuric acid acted as a solvent, and hydrogen peroxide acted as an oxidation agent. Lithium recovery will be studied using a leaching process at various temperatures (30, 45, and 60 °C) and sulfuric acid concentrations (0.5, 1, 2, 3, 4, and 6 mol/L). The increasing temperature, sulfuric acid concentration, and hydrogen peroxide concentration will directly affect the lithium recovery. An increase in sulfuric acid concentration will be directly proportional to the recovery of lithium in the solution. Optimum conditions were obtained at varying 6 mol/L sulfuric acid concentrations and 60 °C temperature variations. The shrinking core model (SCM) studied leaching kinetics, and ash layer diffusion acted as a rate-controlling process. The activation energy of the leaching process was obtained at 38.90 kJ/mol.

Jul 25, 2023

By Anja Pfennig, Axel Kranzmann, Phillip Zastrow

"Properties of pipe steels for CCS technology require resistance against the geothermal corrosive environment (heat, pressure, salinity of the aquifer, CO2-partial pressure). To predict the reliability of two different injection pipe steels with 13% chromium and 0.46% carbon (1.4034, X46Cr13) as well as 0.20% carbon (1.4021, X20Cr13) steel coupons were heat treated by comparable routines prior to long term corrosion experiment (60°C, 100 bar, artificial brine close to a CCS-site in the Northern German Basin, Germany). In general higher carbon content exhibits better corrosion resistance with respect to corrosion rate, amount of pits and maximum intrusion depth in the case of local corrosion. At 100 bar hardened steels with martensitic microstructure have the lowest corrosion rates with an average of 0.003 mm/a after 2000 h exposure time. At ambient pressure normalized steels show the lowest corrosion rates, indicating that the corrosion is driven by grain boundaries.IntroductionEngineering a geological on-shore saline aquifer CCS-site (CCS Carbon Capture and Storage [1-3]) corrosion of injection pipe steels may become an issue when emission gasses, e.g. from combustion processes of power plants, are compressed into deep geological layers [4-8]. Typically 42CrMo4 (1.7225, AISI 4140) is used for casing, and for injection pipe the steel X46Cr13 (1.4034, AISI 420 C) or X20Cr13 (1.4021, AISI 420 J) is used. Saline formations are the most favorable storage sites in Germany [9], because of their large potential storage volume and their common occurrence. Leakage of CO2 back into the atmosphere may be a problem in saline aquifer storage, especially around the water level within the borehole. Carbon dioxide corrosion may cause failure of pipelines and wells as known from the oil and gas industry [4,6,10,11, 12].From thermal energy production it is known, that the CO2-corrosion is sensitively dependent on alloy composition, contamination of alloy and media, environmental conditions like temperature, CO2 partial pressure, flow conditions and protective corrosion scales [6-8,13- 20]. Considering different environments, aquifer waters and pressures, the analyzed temperature regime between 40 °C to 60 °C is a critical temperature region well known for corrosion processes as shown by Pfennig et al. [21-23] and various other authors [10,24-28] (figure 1). Here a maximum around 4.7 mm/year was found for the pit intrusion depth of 13% Cr steel X46Cr13. Still this may be predicted by the rather conservative Norsok-Model used in the oil and gas industry to calculate surface corrosion rates of carbon steels [29]."

Jan 1, 2014

By Andrew Allan

[The Thompson Creek Coal and Coke Corporation, a. mall company engaged in producing coal in the Rocky Mountains of Colorado, is currently engaged in a struggle of destiny to increase their production from inclined seam operation to compete with highly mechanized horizontal bed mines. This paper introduces some of the problems encountered it pitch seam mining as they apply to the convention, room and pillar system employed at the present time. Further described is the test work now being conducted to overcome these obstacles with an. attendant increase in productivity. Included in this test work is a mining machine designed especially for pitching seams, an automated longwall, and hydraulic mining of the latter compared with those of conventional work presently employed.]

Jan 1, 1965

By Felipe Fardin Grillo

The aim of this work was to study the use of slags to desulfurization of cast iron. It was proposed to use alumina instead fluorspar. In addition, marble waste was used instead lime. Simulations applying Thermo-Calc software were performed in order to obtain the theoretical phases thermodynamic data. Then, a comparison between theoretical data and experimental tests were performed. The cast iron was melting in induction furnace at 1550°C. Slags composed mainly for CaO and Al2O3 were used to cast iron desulphurization. It was observed that increasing liquid phase, the desulphurization reaction was favored. Besides, it was found that cast iron desulfurization occurs by top slag mechanism.

Aug 17, 2017

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By R. W. Boyle

"EDITOR'S NOTEPart 1 of this paper, published in the August issue, covered lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos.Part 2, which follows, continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, and geothermometric, geobarometric, thermoluminiscent, pedochemical, hydro-chemical, atmochemical and biogeochemical methods. It concludes with a selected bibliography.Surveys Utilizing Leakage HalosLeakage halos can be used as scalar or vector quantities in thesearch for deeply buried blind mineral deposits. In the first case, the occurrence of a leakage halo (e.g. a small pitchblende seam) may simply indicate the possible presence of pitchblende mineralization or orebodies; in the second case, the areal or three-dimensional distribution of leakage halos may, by their increasing frequency and I or increasing metallic or gangue element content, provide a means of vectoring in on loci of mineralization and orebodies. Examples of both cases are given in the following text.Leakage halos are of many types, as shown in Figure 2 (Part 1), and are best discussed with respect to their associated mineral deposits. Furthermore, it should be noted that leakage halos are frequently offshoots or extensions of enveloping halos. Where this occurs, careful tracing of the leakage halo(s) downward or upward respectively will often lead to the apex or nadir (bottom) of the enveloping halo(s) and ultimately to mineralization or ore."

Jan 1, 1982

In order to assist in the building up of the industries and commerce of France, by cooperating with the Congres General du Genie Civil, the four Founder Societies have appointed the following committee: E. G. Spilsbury and Arthur S. Dwight representing the American In-stitute of Mining and. Metallurgical Engineers; George F. Swain and Nelson P. Lewis to represent the American Society of Civil Engineers; Charles T. Main and George W. Fuller to represent the American Society of Mechanical Engineers; Lewis B. Stillwell and Andrew M. Hunt to represent the American. Institute of Electrical Engineers.

Jan 12, 1919

By O. E. Kiessling

THE present system of competitive exploitation of oil pools results in losses, both of petroleum and of profits. Under a competitive system the owner produces or withholds his product according to the price, which reflects the demand, but in the pe-troleum industry the producer does not have complete control over the expansion and contraction of his out-put. Under a series of court decisions, reviewed in detail in the paper, petroleum is not covered by- the general theory of English common law that the owner of land owns everything from the center of the earth to the sky within the areal limits of his property, but is considered to be his only when he has reduced it. to possession, which he can only do by taking it out of the ground. If A can obtain possession of the petro-leum which is beneath the property of B without tres-passing on B's property he commits no legal wrong and B has no defense except to get it into his (surface) possession before A takes it. No one would expect an. owner under such a system to forego the possibility of securing some oil from his property in order to in-crease the ultimate production of the pool. The pe-troleum industry. should offer a constructive program, that will eliminate losses and protect the interests of individuals as far as possible. If improved methods of oil recovery can be applied the quantity of petroleum recovered might be double or even treble the amount recovered by ordinary procedure. But increased recovery is not the only benefit from pool development. In brief, the following advantages can be claimed for unit operation: 1. Saving in development and operating costs. 2. Less danger of damage to the fields by defective wells. 3. Development is better gaged to fit market demand and to effect the most efficient recovery of oil. 4. More oil, gas, and gasoline can be marketed. 5. By regulating pressures, recovery .of oil and gas will be greater and the wells will flow longer. Reagan County (Big Lake), Rainbow Bend and Cabin Creek are examples of longer life of pools thus obtained.

Jan 11, 1927

By Bertrand L. Johnson

Before 1914 , Chile , because of her extensive resources of natural nitrates , practically monopolized the world markets for one of the leading fertilizer materials . Since nitrogen also is an important war material , constituting in fact the principal ingredient in many high-powered explosives , the World War and the widespread insistence upon national self- sufficiency for war materials brought about the development of nitrogen fixation plants in all of the larger countries . The production of by- product ammonia from gas and coke plants was likewise stimulated . As a result , Chile , even after the ocean lanes were reopened , was forced to fight for her lost markets . Since the world capacity to produce is still far in excess of annual consumption , the competition between natural and synthetic supplies has been keen and prices have fallen below pre-war levels . Chile has recently succeeded in unifying her industry , utilizing the most efficient process now in operation, and the Government is a partner in the new company that will take over all of the present producing companies . These developments place Chilean nitrate of soda , in a much more favorable position among the markets of the world . More intense competition will undoubtedly follow and , in order that those interested may become familiar with the fields upon which the nitrogen conflicts of the near future may be waged , the following general summary of the nitrogen industry has been prepared .

Jan 1, 1931

By John L. Bolles

The Phelps Dodge Corporation's Morenci Concentrator includes facilities for coarse crushing, fine crushing, grinding, flotation, tailing, disposal, concentrate filtering, and drying. The Morenci Concentrator daily throughput is in excess of 60, 000 tons. The ore milled is mainly a medium-hard monzonite porphyry in which the principal sulfide minerals are chalcocite and pyrite. The ore is transported by rail from the Open Pit Mine to the primary crushing plant located at the concentrator site. Ore is side-dumped from 80¬ton railroad cars into a sixty-inch gyratory crusher. The ore is then conveyed to a. 12, 000 ton coarse ore storage bin. Fine crushing is accomplished by four parallel lines of conventionally stacked crushers in open circuit. Each unit consists of one seven-foot standard cone followed by two seven-foot shortheads. Ti% product of the fine crushing plant is distributed by two tripper cars across a fine ore storage bin. The crushed ore is then fed by variable speed belt feeders into thirty parallel, single stage, closed circuit grinding units. Each of the 30 grinding units consists of one 6' x 23' conditioning drum, one 10' x 10' ha l mill and two 54" duplex spiral classifiers as principal equipment. The dry ore is fed into the conditioning drum with water to dilute the ore to a slurry of approximately 78% solids by weight. An aqueous solution of ammonium sulfide is also added to the conditioning drum. The ammonium sulfide primarily acts as a sulfidizing agent. The ore slurry containing the naturally occurring sulfide copper minerals and the sulfidized copper minerals discharges into the feed scoop box of the ball mill, where milk of lime, collector and-.dilution water are added. The ball mill product slurry is gravity fed: to the classifier pool where water is added to obtain the desired classifier overflow product

Jan 1, 1977

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By Joël Kapusta

La pyrométallurgie du cuivre est essentiellement une chaîne de trois étapes successives d’oxydation préférentielle du fer et du soufre et des impuretés moins nobles que le cuivre qui sont contenues dans le concentré de cuivre issu de l’usine de concentration du minerai, aussi appelée concentrateur. La Figure 1 illustre la chaîne complète d’élaboration du cuivre depuis la mine jusqu’au cuivre pur. La voie hydrométallurgique traite le concentré par lixiviation, c.à.d. par dissolution en phase aqueuse à température typiquement inférieure à 100 ou 150⁰C, alors que la voie pyrométallurgique traite le concentré par fusion à température de l’ordre de 1200 à 1300⁰C.

May 2, 2024

By H-S Yang, H Park, S-J Kim, Y-H Ko, H-S Kim, S-H Cho, J-K Kim

An investigation was undertaken to devise a new method for reducing dust spread during blasting demolition utilising water tube and detonating cord. Modelling of smooth particle hydrodynamics (SPH) with AUTODYN software was initially completed to determine the expected diffusing behaviour of the water tube. The actual behaviour was then captured with high speed videos during each experiment, and each result analysed in detail. Water mist diffusion was generated and analysed by changing three key variables. In sequence, these included changing the location of detonating cord in the tube, the charge quantity and the tube diameter.As a result of experiments and simulation, optimum design for ideal diffusion behaviour was suggested and each behaviour of water mist was classified by diffusing shape of water tube as the design criteria.CITATION:Ko, Y-H, Kim, J-K, Kim, S-J, Park, H, Kim, H-S, Cho, S-H and Yang, H-S, 2015. Mist diffusion experiment and evaluation of water tube for blasting demolition dust control, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 809–814 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By K. KAKLIS, O. SAUBI, Z. Agioutantis, R. JAMISOLA

Three-point bending (TPB) tests were conducted on prismatic Nestos marble (Greece) specimens. The specimens were instrumented with piezoelectric sensors, and comprehensive recordings of acoustic emission (AE) signals were obtained. Machine learning in the form of artificial neural networks (ANNs) was then applied in an effort to investigate whether specimen load evolution can be predicted as a function of AE signals. A number of ANN models were developed, and the optimum model was selected based on the highest coefficient of determination (CoD) value as well as the lowest root mean square error (RMSE) value that was calculated for each model. The best performing ANN model exhibits accuracy above 99% with an RMSE value below 4%. It can be concluded that ANNs can potentially be applied to predict rock behavior under load especially when such loads lead to failure.

Sep 7, 2022