Search Documents

By G. L. Humphrey

Although thermodynamic data for ferrous oxide are among the most important in extractive metallurgy, adequate values have not been available until quite recently. The older data suffered not only from the usual experimental difficulties but especially from lack of the knowledge that ferrous oxide of stoichiometrical composition does not exist as a single, thermodynamically stable crystalline phase under any circumstances. This paper reports new experimental data on the heat of formation of ferrous oxide by two methods (combustion calorimetry and solution calorimetry), employing material of unequivocal composition. The results are compared with values obtained from data for the hydrogen reduction, carbon monoxide reduction, and disproportionation reactions of ferrous oxide, and a best value is selected. A table of heat and free energy of formation values of ferrous oxide to 2,000°K is given. These values are combined with available data for water, carbon monoxide, and carbon dioxide to obtain theoretical heats and free energies of reduction corresponding to the selected heat of formation. Hydrogen and carbon monoxide reduction equilibria are compared, and the differences in trend with temperature and the percentage utilization of the reductants are considered.

Jan 1, 1952

By Frank K. McIntosh

Bauxite was first discovered in Tennessee, at Chattanooga, in 1906, during the construction of' the McCallie Street tunnel through Missionary Ridge. Several years later, bauxite was found in sinking a well on the Perry or Isabella Stewart property. These and other deposits furnished a substantial tonnage for the abrasive and chemical industries during the years 1906 to, 1920. The search for domestic sources of war material prompted by World War II brought the Tennessee bauxite deposits to the attention of the Bureau of Mines. During the summer of 1942, James S. Cullison and E. Godwin, geologists of the United states Geological Survey, made a survey of the bauxite deposits of the area. In August 1942, Harold B. Ewoldt, a Bureau of Mines engineer, accompanied by the Geological Survey party visited the area and a drilling program was prepared. Drilling was started in November 1942 and continued until March 1943. A total of 2,519.5 feet in 38 holes was drilled on three properties.

Jan 1, 1949

By Lowell Stroud

Ten natural gases containing from 0.023 to 8.4 percent helium were investigated. In seven high-helium samples, the isotopic abundance of Ne21 was greater than in the atmosphere, being supplemented by 33 to 85 percent of "excess" or "radiogenic" Ne21. The ratio of He4/Ne21(rad) in these gases was evaluated and found to vary between 2.9 x 107 and 5.9 x 107 , a factor of approximately 2. Argon concentrations were determined by the isotope dilution method. The isotopic ratios of Ar40/Ar36 in the high-helium gases were from 5 to 75 times the atmospheric value, with the Ar40 being about 80 to 99 percent radiogenic in nature. The ratios of He4/Ar40(rad) in all 10 gases were evaluated and found to range from 4 to 18. The isotopic ratio of N14/N15 in four of the high-helium gases was essentially the same as in the atmosphere; in three cases it was approximately 5 percent higher than the atmospheric value of 272.0. The genesis of nitrogen and the relationship of nitrogen to helium in natural gases were reviewed and are discussed in terms of a theory for the concurrent generation of nitrogen, helium, radiogenic neon 21, and petroleum (hydrocarbon gases and liquids).

Jan 1, 1967

By E Beltran, S Ngunz, F Orrante, F van Zyl, M Westcott

"The primary control objective of the project is to achieve milling optimisation by ensuring that the energy available for rock breakage is used as efficiently as possible. This is achieved by increasing the level of mill filing until a process constraint is reached. Stable operation against this limiting constraint is then maintained to ensure long-term optimised operation.Semi-autogenous grinding (SAG) mill control optimisation presents a number of challenges. SAG mills have multiple inputs that are used to control multiple outputs (MIMO process). Secondly, the SAG mill loading process is a ‘high inertia’ process that can be approximated as an integrating process. This means that it is open-loop unstable. The hybrid control strategy presented implements an advanced ‘load stabiliser’, which transforms this integrator process into a more manageable first order process, which can be steered stably against the constraints. This SGS hybrid Expert control strategy implemented on both SAG mills at the Porgera concentrator therefore consists of two integrated parts responsible for:stabilising the mill load to a targetdriving the mill load target to the maximum determined by the process constraints (eg maximum power draw) to maximise efficiency and throughput. A comparative study is done between the operation of the plant for a period of a month before and a month after the implementation of this strategy. The results indicated a significant improvement in the SAG mills’ stability and operation as well as a reduction of overload situations leading to a loss of throughput.Citation:Ngunz, S, van Zyl, F, Orrante, F, Beltran, E, Westcott, M and Wilson, S, 2016. Simplified Hybrid Semi-autogenous Grinding Mill Control - Explanation and Practical Results at the Porgera Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Kenneth N. Han

Thermodynamic and kinetic aspects of nickel and cobalt leaching from metals. minerals and ores in various media have been reviewed and discussed in this paper. A kinetic model developed to delineate the leaching mechanisms for these metals has been discussed in view of experimental observations. The current review also includes the dissolution behavior of nickel and cobalt from various minerals such as oxides, sulrides. ocean floor manganese nodules, and laterites. A particular emphasis has been extended to similarities and differences of the dissolution behavior of these two metals in various media. The leaching of nickel as well as cobalt metal in acidic solutions and arnmoniacal solutions exhibits in most part mass transfer controlling. although at some pH's, chemical controlling or mixed controlling mechanisms seem to prevail. The leaching of nickel and cobalt from oxides in acids and ammoniacal solutions. on the other hand, can be described best by chemical controlling mechanisms.

Jan 1, 1993

By W. A. Calhoun

This investigation of low-grade bauxites as potential sources of aluminum by caustic desilication and alumina extraction was undertaken by the Bureau of Mines to develop extractive methods for winning alumina from domestic deposits of low-grade bauxites. This report is the second of a series covering the work by the Bureau of Mines' Rolla, Mo., and Bauxite, Ark., laboratories. The first report published in the Journal of Metals, December 1951,3/ and dealt with kaolin and halloysite. The present investigation is concerned with low-grade bauxites only. The purpose of these investigations is to increase the domestic supply of aluminum ores. With eventual depletion of high-grade deposits, aluminous materials, such as low-grade bauxite, clays, shales, and high-iron laterites, will become our principal domestic sources of aluminum. The development of extractive processes for winning alumina from these low-grade materials is one of the many national security measures undertaken by the Bureau of Mines. A method has-been developed in the laboratory for successfully treating high-silica bauxites from domestic deposits. In this process the bauxite was calcined at 980° C. to form amorphous silica and alumina. The calcine was then leached by percolation with 15-percent sodium hydroxide solution at 940 to 96° C., removing 67 to 77 percent of the silica with a loss of 4.1 to 5.0 percent of the alumina. The sodium hydroxide in the spent liquor used in desilication was 95 percent recoverable, and comparable desilication results were obtained with 100-percent reclaimed liquor, The indicated cost of reagents, for sodium hydroxide and lime used in the desilication and regenera¬tion of spent liquor, was about $4.00 per ton of calcine treated.

Jan 1, 1954

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By H. V. Kinsey

"IntroductionTITANIUM is probably the most widely publicized metal today. Much has been written, both in the lay press and the technical press, about its properties and potentialities. In view of the fact that Canada possesses large quantities of titanium-bearing ore, and could conceivably become a major producer of metallic titanium, it was felt that a paper dealing mainly with the physical metallurgy of titanium would be of interest to this Institute. This paper is concerned chiefly with the useful properties of titanium and its alloys and the fundamentals governing the modification of its properties by alloying.Physical Properties of TitaniumTitanium belongs to a family of metals that have been termed 'gas sensitive' (I), because their mechanical properties are altered by certain gases which they readily absorb and retain. Other metals of this group are zirconium, hafnium, vanadium, columbium, tantalum, and chromium. Titanium has a strong affinity for oxygen and nitrogen and once it has absorbed these gases they cannot be removed either by melting in vacuum or by any degassing agent. These gases, when present in excess of about half a per cent oxygen plus nitrogen, render the metal brittle and useless as a structural material.Some of the typical physical properties of titanium are listed in Table I along with those of common structural metals for comparison."

Jan 1, 1953

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By A Rantala, C Cruickshank, I Muzinda, O Haavisto, J Timperi

The production at First Quantum Minerals’ (FQM) Kevitsa Mine, located in northern Finland, commenced during the second quarter of 2012. Presently, the mine processes approximately five and half million tonnes of ore annually, producing nickel, copper and platinum group metal (PGM) concentrates. In order to support fast production ramp-up and optimise the performance of flotation thereafter, an extensive advanced flotation control solution was implemented by Outotec in collaboration with FQM Kevitsa.In addition to basic process instrumentation and process control, each of the 14 Outotec 300 m3 and another 26 cells, ranging from 20–160 m3, have been equipped with state-of-the-art systems providing froth image analysis and automatic froth speed control. Also, the flotation cell levels are stabilised with advanced feed-forward level control.The online analyser provides key feedback information of the process performance for the advanced process control (APC) system. Based on this information, APC system defines grades and recoveries according to rules defined by Kevitsa process metallurgists. This system executes the control strategies for optimising the production of concentrates.Throughout the implementation and support phases, specific and intensive attention was paid to ensure plant personnel gained full understanding of interacting with the system and how to incorporate their process experience and skills to optimise the APC strategy. This level of expertise is also a valuable asset in understanding the APC system’s contribution to the overall performance of the plant as well as providing the ability and confidence to define key performance indicators used for continuous assessment. The experiences and results from site achieved so far are discussed in this paper.CITATION:Rantala, A, Muzinda, I, Timperi, J, Cruickshank, C and Haavisto, O, 2014. Implementation of advanced flotation control at First Quantum Minerals’ Kevitsa mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By Jr. Frost

Helium used as a tracer gas in petroleum reservoirs continues to show great promise as a new tool for the oil and gas industry, according to tests conducted jointly by the Bureau of Nines and The Pure Oil Co. in-the Cabin Creek field, Boone and Kanawha Counties, W. Va. Helium, when used as a, tracer gas, is mixed with natural gas being injected into a reservoir for secondary recovery of oil, recycling, pressure-maintenance, or other purposes. Three separate experimental helium tracer-gas tests were run in the Cabin Creek, W. Va., field, wherein helium was added as a tracer to the natural gas that was being injected into the oil-bearing Berea sandstone. The results obtained in each test permitted determining the direction and rate of travel of the injected gas, calculating the volume of injected gas in the gas produced at the various wells, and determining the nature of the transition from natural gas to injected gas during a gas-injection program. Data were obtained on the effects obtained from waves of injected gab containing 1 percent and containing 5 percent helium and from a wave of essentially pure helium injected into the formation.

Jan 1, 1950

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By Serdar Aktaş, Özgün Küçükoğlu, Burcu Nilgün Çetiner, Mehmet Hakan Morcalı

This study compares the cementation performance of metallic iron, metallic aluminum, and metallic tin in terms of the reaction conditions and parameters in synthetic antimony chloride solutions. The effects on the antimony recovery (%) caused by the cementators’ types, stirring speed, reaction time, and temperatures were explored thoroughly. The cementation kinetics of antimony were also explored for each cementator. The activation energies were determined to be 10.99, 9.09, and 13.58 kJ mol– 1 for Al, Fe, and Sn, respectively. The results reveal that the reaction is diffusion controlled, and comparable results were obtained for each cementator. At 25 °C, 40 mg of iron powder was found to reduce all antimony ions (i.e., approx. 99% recovery), but even when 100 mg of Al and Sn cementators were used, the antimony recovery did not reach 100%. This result shows that iron is the best candidate to cement antimony out of the solution.

Jan 28, 2022

By B L. Sainsbury, M F. Lee, A Penney

For most practical rock engineering purposes, stress versus strength conditions around underground openings for which rock masses fail and their various modes of failure, are reasonably well-understood and predictable. Some rock masses and particular rock types fail slowly and relatively quietly. However, others can fail rapidly, violently and maybe with the ejection of significant broken rock. In some countries and in some mines, the latter style of violent fracturing and failure of the rock mass is referred to as ‘strain bursting’. It can be alarming and extremely hazardous to nearby miners and machines. For such situations, the design and installation of appropriate ground support, to provide a safe work place, can be challenging. At any particular mine site, it’s often generally understood which local rock masses (rock types) are prone to strain bursting. Competent and strong siliceous rocks and some massive sulphides are often the main offenders. While some neighbouring, equally-competent and strong rocks might also fail, they do so more quietly and without ejection. To understand this contrast, a better understanding of the fracturing process is required other than simple and standard strength versus stress considerations. Suites of standard intact rock properties from numerous Australian mines have been used to define and help understand different high-stress failure styles for component intact rock; especially those prone to violent fracturing (strain bursting). Simple considerations of micro-fracturing (defects in the intact material), plus the available energy at failure versus the energy consumed during fracturing, distinguishes between over-stressed and competent rock types that fracture violently and those that don’t. CITATION:Lee, M F, Penney, A and Sainsbury, B L, 2018. Proneness of competent over-stressed intact rock to violent fracturing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By F. Y. Kang

Graphite with layers structure is easily to form graphite intercalation compounds (GICs) by means of intercalation reactions due to the weak cohesion force among carbon layers, van der Waal?s interactions. By controlling the oxidation-intercalation, high quality exfoliated graphite with low residual sulfur content and MClx-GICs (M=Fe, Co, Ni, Cu, Zn) powder for electromagnetic wave absorbing and shielding materials have been invented. The expansion volume of expandable graphite can be larger than 160 mL/g while the residual sulfur content is less than 800 ppm. The MClx-GICs powder can shield infrared ray and laser completely up to 15 min. We have also in-vented exfoliated graphite for heavy oil adsorption and mild-expansion exfoliated graphite for anode materials in lithium ion battery by controlling the intercalation/de-intercalation. The exfoliated graphite can adsorb heavy oil up to 80 g/g, it also exhibits better performance than commercial active carbon in sewage treatment. The mild-expansion exfoliated graphite as anode material shows high capacity of 370 mAh/g and good cycle performance.

Jan 1, 2014

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone&apos;s lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China&apos;s dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963