Search Documents

By P. Strand

Talk Outline ? Location and Regional Geology ? Two Unique Kimberlite Sources ? Mineral Chemistry ? Petrography, Age Dates ? Geophysics ? Exploration and Challenges ? Dyke versus Pipe dispersions ? Geophysics ? Prospecting ? Diamond Results ? Summary & Conclusions

May 1, 2008

By B. Oraee

Tunnels as any other structures are affected by different loads and stresses. Generally, the loads on tunnels consist of both static and dynamic loads. These loads must both be considered in the tunnel design process. In this paper, the stability state of Jiroft water-transform tunnel is evaluated. Firstly, the in-situ stresses and then using Kirsch?s equations the induced stresses due to static loads in walls and crown of tunnel are calculated. Consequently, the strain caused by probable earthquake without considering the interaction between the concrete lining of tunnel and rock mass using seismic analysis is calculated based on free-field deformation. When the strain is determined, the simplified method of closed-form solution, Wang?s equations and Penzien?s equations are used to estimate the applied forces on the tunnel due to earthquake such as axial force and bending moment on a tunnel section taking into account the interaction of the tunnel concrete lining and rock mass. Results of this study show that the loads applied to the tunnel as a result of earthquake waves can be affect the stability of underground structures, especially long structures such as tunnels.

Jan 1, 2011

By Jim Ploger, Peter W. Johnson

Bus drivers represent a large segment of the US transportation industry and research has shown an association between exposure to Whole Body Vibration (WBV) and the high rates of low back disorders. Impulsive WBV exposures have been recognized as a risk factor for low back injury and new guidelines exist for their measurement and assessment (ISO 2631, Part 5). Methods to accurately and better characterize the impulsiveness of WBV along with the temporal patterns of the exposures are needed. The development of a hardware and software system to measure continuous TWA and raw, impulsive WBV exposures and the design of a subsequent study are presented. Methods Using two Larson Davis HVM 100 as accelerometer amplifiers, small external batteries, and a Pocket-PC (PDA) with 1 Gb of compact flash memory, we can collect up to 16 channels of data for a full day 600 Hz. Tri-axial WBV exposures will be measured and characterized at the frame of the bus and at the driver/seat interface (seatpad accelerometer). Using a repeated measures design, 20 bus drivers will drive on selected routes which include both city streets and highways, and within and between subject components of variability and exposure determinants related to the bus, bus seat, the bus driver, and the route will be identified. Global Positioning System (GPS) data will also be collected and integrated with the WBV exposure data to facilitate the identification of the location, velocity and type of road associated with high average TWA and impulsive WBV exposures. This system may be used to develop administrative (alter speed and/or route of bus, systematically vary type of routes) and/or engineering controls (identify and trigger the need for street repair) to reduce high WBV exposures. Results Our portable Pocket-PC based data acquisition system is up and running and we can collect seven channels of WBV data (seat pan tri-axial accelerometer, bus frame tri-axial accelerometer and GPS data) continuously for a full shift. The software analysis of the data is complex but nearing completion. We have incorporated the vibration dose calculations from ISO 5321, Part 5 and have obtained a Matlab-based routine to appropriately weight the continuous signals. Discussion In summary, the measurement of WBV is complex but new technologies open avenues of collecting and assessing WBV exposures that were previously not possible. The standardization of impulsive WBV exposure assessment methods is needed to further the discipline and better enable comparisons across studies.

Jan 6, 2006

By Alice Turcot

Knowledge of risks from exposure to hand-arm vibrations is usually presented by clinicians and researchers from a medical and engineering point of view. There is a strong need to develop innovative health promotion programs for exposed workers. Risk perceptions by vibration exposed workers and HAVS (hand-arm vibration syndrome) affected workers are less well known. In 1983, Brubaker demonstrated that 75% of studied fellers thought that whitening of the fingers was part of the job and/or an unrelated nuisance, while only 25% believed it was a disease. 1Grounds also showed that even though there were a very high number of forestry workers with white fingers, none considered quitting because of their condition. 2 It seems that many workers hesitate to declare the illness or believe they are less affected than they really are, perhaps from fear of losing their jobs and livelihood. 3 Risk awareness, on the part of exposed workers and their employers, as well as knowledge and acceptance of available preventive solutions are necessary steps before installing adequate preventive measures, whether organizational, behavioral or environmental. Workers need to understand fully the hazards and risks in order to be able to make informed decisions under uncertain conditions.4 Prerequisites include the following: workers knowledge about the risk, their attitude towards it, which in turn, can be influenced by values, needs and interests. Also, knowledge and attitudes towards safety behaviour, organizational or environmental barriers must be taken into account. Our research focuses on these key elements, which help bridge the gap between health promotion research and practice. Methods A descriptive exploratory study is in progress with workers exposed to hand-arm vibrations. It uses qualitative methods that include focus group discussions with workers exposed to hand-arm vibrations, as well as individual interviews with other key informants (employers, health care professionals). An open-ended questionnaire was developed to collect qualitative data on perceived risks and solutions to prevent or reduce HAVS. Based on an integrated theoretical framework related to known determinants of behavior change, the analysis will focus on the following5: 1) knowledge of health effects, safety, well-being and/or quality of life 2) related beliefs about individual susceptibility and severity of consequences 3) attitude and values related to hand-arm vibration exposure 4) knowledge and attitudes towards exposure reduction, as well as perceptions of barriers and facilitating factors for these measures, in the workplace environment or otherwise.

Jan 6, 2006

By C. Vanvoren

"Since 1975, the Aluminium Pechiney Research Centre at Saint-Jean-de-Maurienne (LRF) has been concentrating its efforts on designing, testing and perfecting the Aluminium Pechiney point-fed prebaked reduction cell.In 1979, the AP18 cell (180 kA) was industrially launched with the construction and start-up of the F line in Saint-Jean. The following generation, the AP30 (300 kA), with prototypes started in 1981, was launched in 1986 on the Saint-Jean G line. Along with cell design, efficient process control systems were developed to pilot alumina feeding and bath composition. Together, these pots are currently producing 4.6 Mt of aluminum, i.e., 18% of the world’s overall yearly production.In 1989, the research centre faced a new challenge: to push the limits for the size of a reduction cell to further improve the profitability of Greenfield projects. This new generation development was also the opportunity for a significant redesign of the Aluminium Pechiney electrolysis information system.With a track record of ten years of semiindustrial operation with three prototypes, the AP50 technology is now ready for industrial implementation and enables a significant breakthrough to be made in terms of return on investment of a Greenfield smelter."

Jan 1, 2002

Large mining operations need equipment that consistently performs as expected. The most effective way of ensuring this is to have a defined life cycle with an optimised maintenance strategy. The determination of this life cycle is an economic decision, influenced by the construction and utilisation of the equipment. An effective life cycle costing (LCC) tool must be able to process the many variable factors involved.Many factors influence the costs that are associated with a machine over its life. The most variable of these are the costs of maintaining the equipment. Maintenance costs are dependant not only on the utilisation of the machine, but also on the strategy that has been developed to support the machine through its life. A combination of supplier support, component changes, regular servicing and unscheduled maintenance needs to be modelled, based on a variety of drivers. Traditionally spreadsheets have been used to model these factors, but the increasing complexity of the situation can make spreadsheets unwieldy and difficult to manage. A database solution that breaks each activity into its constituent components, links them to an associated mine plan driver and then aggregates the result is the ideal tool to provide a time based cost profile. The evaluation of a number of scenarios, representing different maintenance strategies/life cycles can be rapidly undertaken. Auditability through inbuilt tools is required to provide easy tracing of data. Use of the host company's account structure allows for reporting against the standard chart of accounts.

Dec 6, 2010

By M. G. Wimberger

The Merensky Reef zone, as developed on Impala Platinum?s Rustenburg Operations, displays a gradational mineralized zone, with grades decreasing from the Merensky Pegmatoid Unit into the footwall and hanging wall. A system of identifying a manageable method of defining the mining cut is introduced, termed the grade profile attenuation cut-off grade. Although horizontal grade selectivity is not applied in the mining of the Merensky Reef zone, low extraction of the orebody, due to manageable and non-manageable factors, can contribute to a reduction in revenue, even losses, due to fixed cost contributions in the mining and beneficiation of the ore. A model is proposed that integrates all variables affecting the revenue of the mining operation, including the grade profile attenuation cut-off grade, the extraction factors, commodity prices and exchange rates, utilizing numerical simulation techniques in a PC-based environment. A breakeven extraction factor for a specific cut-off grade is delivered for a range of market conditions. The breakeven extraction factor is a useful guide when designing mining layouts in structurally complex and low metal content areas. Incorporating distribution functions for individual commodity prices and exchange rates into the model provides mineral resource managers with a risk profile for individual mining areas. Shaft areas have varying grade profiles and each area should have individual models run, to prevent generalizations being made about acceptable risk levels on mining areas.

Jan 1, 2004

By B. W. Roberts, V. A. Phillips

A copper alloy containing- 25.5 at, pct Zn and 19.0 at. pct Ni, which was previously found to show an anoma1old.s hardening effect on quenching- from 600 "C and aging- at 400oc, has now been examined by neutron diffraction. No evidence of long-range order was found. The aged sample showed diffuse scattering- consistent with clustering. The anomalous hardening effect is now attributed to lattice strains caused by clustering rather than (long-range) order hardening. SOLID-solution Cu-Ni-Zn alloys (the commercial 'nickel silvers") have been reported to show anomalies in: change of resistivity on cold working,1-6 temperature coefficient of resistance,2-12 resistivity at low temperatures,13,14 parameter (vs temperature),2"4 calorimetric data,2,4 specific heat,15,16 dilation,2-4 and elastic modulus.17 The structure responsible for the anomalies is produced by annealing typically near 400°C and is rather loosely referred to as the ('K-Zustands" (K state), a term coined by Thomas1' who apparently meant simply that the arrangement of atoms on the sites deviated from that expected statistically. Thomas proposed that the K state occurred in a variety of (solid-solution) alloys such as Cu-Ni-Zn, Ni-Cr, Ni-A1, Ni-Cu, Fe-A1, and Fe-Si and is recognized because its formation is strongly temperature-dependent and results in an increase in electrical resistance which can then be decreased by cold working. Later workers on ('nickel silver" have interpreted the K state variously as short-range order, long-range order. or a combination. The present work was prompted by the discovery by Phillips and Jones19 of a substantial hardening effect when an 18 pct "nickel silver" alloy which is fairly close to the Cu2NiZn composition, was reheated in the range 150" to 450 C after previously quenching from 600°C or, alternatively. was slow-cooled from 600°C or above. The phenomenon was attributed to (long-range) order hardening. Due to the similarity in the atomic scattering factors of copper. nickel, and zinc atoms, the ''nickel silvers" are unfavorable for X-ray diffraction studies aimed at detecting ordering. Nevertheless Bialas et a1.,20 using a powder sample containing 47.96 wt pct Cu, 24.03 wt pct Ni, and 27.98 wt pct Zn, slow-cooled from 400" to 200°C taking 500 hr, observed weak super lattice lines. Further unpublished work" using an anomalous dispersion X-ray technique indicates that zinc atoms are regularly ordered at the corner points of the lattice cell, while the nickel and copper atoms are statistically distributed on the remaining sites. Köster 17 also observed X-ray superlattice lines, for example, in an alloy containing 43.5 wt pct Cu, 28.6 wt pct Ni, and 27.9 wt pct Zn superimposed on the basic fcc cell with a = 3.62 kX. He proposed a Cu3Au-type superlattice with the Ll2 structure in which the A sites were statistically occupied by copper and nickel atoms and the B sites by zinc. He adds that substitution must be possible so that zinc atoms partly occupy A sites. Below about 35 pct Cu, Koster had some evidence for a CuAu-type superlattice with the Llo tetragonal fcc structure with a = 3.82 kX, c/a = 0.88 which could be preserved by quenching. This is suggested17722 to correspond to CuNiZn. While the present work was in progress Hirabaya-shi et a1.23 made an independent comprehensive neutron-diffraction study of a single crystal containing 50.05 at. pct Cu, 26.57 at. pct Ni, 0.25 at. pct Mn, 0.13 at. pct Fe, balance zinc. The presence of manganese and iron is surprising since the crystal was supposedly grown from high-purity metals. The homogenized crystal showed evidence of long-range ordering after an anneal of 5 months at about 300°C. Three possible crystal models were proposed. A curious feature of their results23 is that they could not find any neutron-diffraction evidence of ordering in a powdered polycrystalline near-stoichiometric Cu2NiZn alloy. There appears to be some essential difference between a near-stoichiometric Cu2NiZn alloy and one somewhat further off stoichiometry as used by the present authors. Thus Sato14 was able to reproduce the low-temperature resistivity anomaly reported by one of the authors13 on the present alloy if he used a similar composition, but found the normal behavior of the residual resistivity in a near-stoichiometric alloy. satol2 found that the resistivity of a cold-drawn slightly off-stoichiometric alloy increased to a maximum on isothermally annealing at 300°C and then decreased ("over-aged"). Since he could not explain this on the basis of ordering phenomenon, he proposed that zinc atoms were segregating to stacking faults (Suzuki effect) and found etching bands on the surface by replication which were attributed to the widening of faults. Sato suggested14 that the hardening effect observed by Phillips and Jones19 is partly due to the Suzuki effect. EXPERIMENTAL The starting material was 1/4-in.-diam hard-drawn rod of a commercial 18 pct "nickel silver" alloy identical with that used in a previous study by Phillips

Jan 1, 1967

By L. Munsamy, B. J. Madden

OpenRisk, an open cast risk rating system, takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and operational parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all the strip mines would use an identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. This system has been made practical and easy to use. Therefore, this tool can be used by personnel from other disciplines not directly related to rock engineering. OpenRisk system has been in operation at nine Anglo Coal and other open cast mines. It adequately detects areas of high risk and generates adequate remedial solutions to reduce the risks. Awareness of the personnel has been higher at the sites that use OpenRisk. The proactive approach of OpenRisk ensures that all personnel are aware of risks in the pits and how to deal with potential risky areas.

Jan 1, 2006

By T. G. Joseph, G. W. Hansen

"This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sands material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 sq. yd. Consequences are manifested in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability.The objective of these considerations, as part of the Oil sands-Equipment Interaction Program (OsEIP), currently a joint venture between Syncrude Canada Ltd., James Progithin International (JPi) Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta, is to identify and provide feedback to the manufacturer and end user of adverse shovel-ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance."

Jan 1, 2002

By D. C. Hogeman

Growing Greener is the single largest investment of state funds in Pennsylvania’s history, allocated to address the Commonwealth’s critical environmental concerns. Signed into law by Governor Tom Ridge on December 15, 1999, Growing Greener will enable the Department of Environmental Protection (DEP) to appropriate nearly $240 million over five years, to watershed restoration and protection, abandoned mine reclamation, and oil and gas well plugging projects. DEP has utilized these allocations in some remarkably innovative ways, as it: involves the cooperation of several state agencies, local governments, and grassroots organizations to address environmental concerns of the Commonwealth, provides funds directly to watershed groups based on locally determined decisions for local watersheds and offers a user friendly process. In three years, over $130 million in watershed restoration and improvement projects have been initiated.

Jan 1, 2002

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

By Susumu Tsubota

Three types of reference gold catalysts, i.e., 3wt%Au/TiO2 (Au-Ti: Type A), and 0.3wt%Au/Fe2O3 on alumina beads (AUS: Type B), and 5wt%Au/Fe2O3 (Au-Fe: Type C), were produced in a test plant scale by Sud-Chemie Catalysts Japan, INC. under the licensing of AIST. To evaluate the validity of the preparation methods and conditions used for the reference samples, elemental analyses by ICP, particle size measurements by TEM, and catalytic activity measurements for the oxidation of CO and H2 over these catalysts were made. Gold catalysts can be prepared in a large scale of ca 400g for the Au-Ti and Au-Fe catalysts, 5 kg for the AUS catalyst with good reproducibility. It was confirmed that they were available for useful as the reference gold catalysts of World Gold Council.

Oct 1, 2003

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

By Jack Wasserman, Don Wasserman, Logan Mullinix, Shekhar Khanal, Kelly Neal

This paper presents current finding on truck driver average exposure to acceleration for several different manufacturer’s cab-over trucks on a variety of roads in different countries. The predominant time, for this aspect of the study has been spent in the area around London, England and Warsaw, Poland. The ECE directive 2002/44/EC has provided specific guidelines for vehicle operators 8 hour average acceleration exposure. The primary considerations have been on truck design including the air-ride driver’s seat. The truck manufacturers have produced truck cabs that have some separate suspension from the truck frame. The truck seat manufacturers have been producing air-ride suspension seats for the cab. Both of these designs have had the objective of meeting the ECE directive and providing the vehicle drivers with some degrees of comfort. This paper will provide some information on the ability of the vehicles to operate on a variety of roads and meet the objectives. Method The primary method for evaluation of the driver’s exposure has been the use of a seat pad attached to the driver’s seat. Although this sensor system provides the critical information for the driver, an understanding of the reasons for the values requires additional measurements. The initial study in England used both driver and passenger seat pads, as shown in Figure 1, as well as triaxial accelerometers mounted on the base of the seat. The latest studies used significantly more transducers to better understand the relative rotations and translations on the truck frame, the cab, and the driver. [ ]

Jan 6, 2006

Jan 1, 1967

By J. L. Goen

The Saint Joseph Hospital of Bellingham is located on a site underlain by glacial outwash. The construction of a five-story tower addition above an existing two-story wing was supported by five large trusses that impose a 1600 kips (7117 kN) column load on five pile caps in the courtyard of the hospital and on the new pile caps inside the existing MRI laboratory. The exterior columns of the trusses and the new parking garage addition were supported on conventional auger cast piles installed with conventional equipment. Helical Pulldown® micropiles were selected for use in the courtyard and the MRI laboratory because lightweight installation equipment (maximum unit weight of 7.5 kips (33.3 kN)) had to be used and it was required that no spoils be produced. The installation equipment was lifted into the courtyard by the jobsite crane. Sixty Helical Pulldown micropiles were installed for the pile caps in the courtyard. The pile caps inside the hospital were supported on 240 Helical Pulldown micropiles. Initial compression test indicated an allowable load for the micropiles to be 55 kips (244 kN). However, retest at a later date resulted in an increased allowed design load to be 85 kips (378kN) reducing the number of micropiles required by more than fifteen percent.

Jan 1, 2004

By M. Hermanus

1. INTRODUCTION It gives me great pleasure to extend my warmest greetings to everyone attending the 30th International Conference of Safety in Mines Research Institutes. I would also like to bid a special welcome to all of the international delegates who have travelled to Johannesburg to take part in what surely be a most rewarding session of deliberations. As you come together over next four days, you will have a wonderful opportunity to exchange ideas and information on strategies and practices for the implementation of sustainable patterns of development. The objectives of this meeting are both timely and far-reaching, as countries around the globe work towards the sustainable use of the world resources. Each of you brings a high level of expertise to these deliberations. I know that you will make the most of this opportunity to address the challenges and opportunities to highlight the most innovative and technologically efficient methods of social protection in order to ensure an increase in the quality of life, health, safety and living environment for the peoples of the Africa. Our country, although endowed with an immense and diverse array of mineral deposits, is perhaps best known in the mining industry for the fact that it is the world’s biggest producer of gold. Although South African gold production has declined over the past years and the industry faces serious problems, it is a myth that the South African industry is moribund. There is a new energy coursing through the South African producers which will ensure their powerful presence for many years to come, based not only on their domestic production but also and probably increasingly on their external operations. Africa features prominently in the latter category.

Jan 1, 2003

By Ligon Johnson

ONLY the acute phase of the smelter fume problem is new. The problem itself is older than the Christian era. While both lead and copper were mined and crudely smelted ; on: 3,000 years ago, it was not until the Roman occupation of the Iberian Peninsula and the British Isles, which occurred but shortly before the beginning of the Christian era, that there was any evidence of smelting operations on a scale sufficiently large to permit a fume problem. Around Huelva, Spain, are found more than 30 million tons of slag from lead smelting conducted there by the Romans. Pliny tells us that more than 20,000 slaves were employed in the Iberian mines. Extensive mining and smelting by the Romans in England and Wales were coincident with the Iberian proceedings. These metallurgical operations were upon a sufficiently large scale to produce marked results both upon the surrounding country and the smelter workers, but, as they were those of a conqueror upon conquered soil, conducted by slaves, imperial Rome failed to recognize that such a thing as a smoke problem did or could arise, and whatever fume question there may have been at that .time remained a question only to those who had no chance to answer any phase of it. The smelting operations of the Romans extended over about 400 years, and little is "recorded of lead and copper smelting from that time until the 16th century. From the revival beginning at this period up to the present century, the growth of smelting has been comparatively gradual. In Great Britain, smelting was conducted almost wholly in localities where metallurgical operations were of paramount importance, and the communities that grew up in smelter localities were due to and dependent upon the mines and smelters. This fact had much to do with the comparative freedom of British smelting from burdensome fume litigation and legislation. To a lesser degree these conditions applied to the German operations which, when coupled with the further fact that most of the early German operations were to a greater or less degree fiscal workings of Prussia, Saxony and Brunswick-Hanover; accounts for

Jan 5, 1917

As a minerals company, obtaining the appropriate consents under the Resource Management Act 1991 and getting permits granted for exploring, prospecting and mining under the Crown Minerals Act 1991, is necessary for actively exploring and mining in New Zealand. But the essential mix of ingredients for a viable and healthy Industry go way beyond this.   In the short term, an individual company seeking to operate on or within the Crown minerals estate of New Zealand must chart a course through the requirements raised by new cornerstone legislation, the Resource Management Act, the Crown Minerals Act and, the Conservation Act 1978 (where the minerals sought coincide with this estate).   However, this paper suggests that in the longer term for individual operators within the Industry and for the Industry at large to remain viable and sustainable and for New Zealanders to continue to enjoy its benefits, much more is required. Not least of which is a better balancing of competing uses and attitudes, which will require an opening of minds, a change in mindset, topped off with those two most essential of ingredients advocacy and leadership.   New Zealand has undergone massive restructuring in the last 15 years. Is it complete? Have each of its fronts evolved to the end point which was envisaged by the designers of the regime? What are the advantages? What is left to be done? What are the impediments from an incomplete transition which are left to either dog the Industry or remain as a challenge to be removed to ensure the Industry's smooth sailing into a prosperous and environmentally clean and friendly future? A future wherein an educated and understanding public welcome and are proud of the Minerals Industry to whom they owe the standard of living which they enjoy.   This presentation will examine the role of the New Zealand Minerals Industry Association (NZMIA) in paving the way for an optimum operating environment in which to couch a healthy industry into the future.

Jan 1, 1997