Search Documents

By A. Yehia, M. I. Al-Wakeel

Flotation behavior, of magnesite and dolomite pure minerals was studied separately. Rice bran oil (a source of fatty acid ) was used as a collector for both minerals . The aim of this study is to find a separating zone in the flotation of these pure minerals to be used in the separation of their mixture. Factors affecting the flotation process, such as pH and collector, were studied. It was found that magnesite can be separated, from its mixture with dolomite, in the pH range of 5-7. At this pH range flotation recovery of dolomite reaches~98% where magnesite reaches ~20% only. Besides, the effect of collector concentration on the flotation shows that the separation of magnesite from dolomite is feasible at a collector concentration of 3x10-4 M. At such concentration, dolomite recovery reaches ~98%, where magnesite reaches 25%. The differences in the flotation behavior of dolomite and magnesite were investigated by studying the adsorption isotherms of rice bran oil on magnesite and dolomite surfaces. The adsorption study indicates that while there is an excessive adsorption on dolomite surface, the adsorption density on magnesite was restricted to be lower than monolayer capacity. The adsorption behavior of dolomite and magnesite was discussed in the light of their solubility and crystal structure. It was found that due to the higher solubility of dolomite than magnesite, Ca2+ and Mg2+ ions are available and more reactive on dolomite surface increasing collector adsorption. In addition, it was indicated that dolomite mineral has a crystal lattice structure more compatible to the geometry of the fatty acid carboxylic group than magnesite. However, the adsorption of collector on dolomite surface is more compact and more regular than on magnesite surface.

Jan 1, 2000

By K. F. Bailey

Naturally occurring asbestos in aggregate and other mineral deposits, and the release of asbestos fibers into the ambient environment, is a public health concern. Determining the presence of asbestos in an ore body also presents a considerable sampling and analytical challenge. Improper and inaccurate identification of asbestos can result in unwarranted public and worker panic leading to significant costs to mine operators both in terms of dollars and company image. Some companies have been forced out of business simply because they had the non-asbestiform, prismatic variety of one of the six asbestos minerals. In the late 70’s, asbestos was found as a contaminate in a trap rock quarry in Rockville, Maryland. This discovery led to a massive overreaction by federal, state and local governments. In 1986, the Occupational Safety and Health Administration (OSHA) promulgated a final rule that regulated the common non-asbestiform mineral habits of actinolite, tremolite, and anthophyllite as if they were asbestos. The rule was reversed after a six-year struggle. Recently, the Libby, Montana, W. R. Grace vermiculite - asbestos, as well as the California chrysotile in serpentinite, and the New Jersey Southdown quarry – asbestos events have rekindled the entire issue of naturally occurring asbestos. It is time to get this concern addressed with sound science so that real asbestos is properly identified and controlled.

Jan 1, 2002

By T. G. Joseph, K. Barron

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an “apparent friction” concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of triaxial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock. This strain-softening relationship is then applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post-failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

Jan 1, 2003

Attempts to rationalise the geological environment of nickel sulphide deposits associated with Archaean ultrabasic rocks has produced much speculation as to the origin of the sulphides and the relative importance of geochemical, mineralogical, textural and structural characteristics of the host rocks. From an economic viewpoint the object of such work is to establish geological criteria which can be used as an exploration guide. Exploration procedure for nickel sulphide mineralisation of the 'Kambalda type' (Hudson, 1972), which occurs at or near the basal contact of Archaean ultramafic flow units and lenses consisted of geological mapping, surface prospecting with soil sampling and rock geochemistry.

Jan 1, 1987

By Andy Alder

The aim of this paper is to provide an overview and details of good practice, from a United Kingdom perspective, in the development and implementation of major tunnel and underground infrastructure projects. In doing so, it draws on a broad base of project management theory. A central theme is that successful project delivery is dependent on detailed planning of the complete project delivery process, forming an effective team that works well together and the proper management of risk. The role of partnering in forming a strong project coalition is described. Particular emphasis is given to the integration of design and construction, and the role of the designer throughout the construction phase. The implementation of risk management in the design and construction of tunnel works is discussed, and recommendations are made on how risk, value and constructability can be integrated in project delivery. Recent practice in project procurement, particularly in the use of innovative collaborative forms of contract are described, and details of particular provisions for joint management of risk and problem resolution are provided. Finally, the relevance of the ITIG Code of Practice for Risk Management of Tunnel Works to good practice in project delivery is highlighted throughout the paper.

By Jens Classen, Martino Gatti

"GENERAL PROJECT DATAThe Sparvo Tunnel is part of the “Variante di Valico” project, a new 65km (40mi) highway link between Bologna and Florence, designed to renew the existing A1 route which connects Bologna and Florence. It is composed of 2 x 2,5km (1,55mi) twin tunnels excavated inside a complex geological context, characterized by the presence of a series of surface landslides and methane gas.The inclination is 2,6 % and the minimum radius is 1.400m (4.600ft). The two tunnel tubes were excavated by a 15,6m (51ft) diameter EPB-TBM from summer 2011 to summer 2013. The internal diameter of the concrete lining is 13,6m (44,5ft), made up of precast concrete segments 2m (6,5ft) long and 70cm (28”) thick, being the largest and heaviest segments ever produced. Excavation went smooth apart from initial problems concerning clogging problems and a main bearing damage of the TBM, which are discussed in a further paper during the congress. No structural damage was observed until the end of the TBM drives.SITE OBSERVATIONS DURING THE POST-EXCAVATION PHASEThe first evidence of the stress state of the segmental lining appeared on November 20, 2013 inside the northern tube (1st drive). Ring No. 884 showed obvious signs of overstress, resulting in spalling and crushing of the concrete, and the subsequent bending of the reinforcement, as visible in figure 1.At this time the tunnel invert was already partially backfilled, and construction traffic was running through the tunnel. First safety measures included closing of the tunnel, and initial measurements of the displacements."

Jan 1, 2016

By C. Navalkar

Systematic drilling & blasting techniques are currently being viewed in the mining & construction industry as a correct 8z scientific approach for optimization process in rock excavation, as drill & blast costs usually represent major share in total cost of production and also the environmental impacts plays an important role in designing of the operations. Designing a blast is a complex planning task, which for optimization, includes deciding the bench geometry with respect to the rock properties & geology of the area, capacity of the excavators, choice of explosives & detonation method, tiring sequence, etc. Optimization of blast design needs a detailed comprehensive study of all the above intersecting elements. Preblast & Post blast surveys are required for further improvements in blast designs. However, the choice of blast design depends upon the the requisite blasting results opted for and the cost you are ready to pay for the same. The blasting operation, in general, also involves numerous side effects namely, ground vibrations, fly rocks, dust, noise & gas pollution, air blast effect etc. Again these effects can be made tolerable up to a certain extent depending upon the limitations of the environmental obligations as may be specified by the concerned authorities.

Jan 1, 2001

By J Addai-Mensah, W Skinner, K Quast

The efficiency of any iron ore value-adding operation is closely associated with detailed knowledge of the mineralogy, especially in the processing of lower grade and complex ores. There are a number of physico-chemical properties of iron oxide mineral phases (eg goethite, hematite and magnetite) that can be prudently exploited to enhance their processing efficiency. Recent iron ore studies on the upgrading of high-goethite iron ores have highlighted that the knowledge of the various phases of both iron oxide and gangue minerals is critical to the economic processing of these ores. Appropriate knowledge of this kind can lead to better-designed flow sheets for economically viable production of saleable products. With the increasing use of goethitic materials as blend components of iron ore concentrates for steelmaking, this review paper focuses on relevant beneficiation processes and the pivotal role of mineralogy and petrology in producing saleable iron oxide concentrates from ore blends. For goethites, mineral impurities including silica, phosphorus and alumina are very important. Physical separations, as well as those incorporating higher temperatures, have also been included in this review as potential processes to upgrade high-goethite ores.CITATION:Quast, K, Addai-Mensah, J and W, Skinner, 2017. The importance of mineralogy and petrology on the beneficiation of iron oxide ores, primarily those containing goethite, in Proceedings Iron Ore 2017, pp 233–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Discussion of the paper of Frederick Laist, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1147 to 1162. J. C. DICK, Salt Lake City, Utah :-I would like to ask Mr. Laist why a 10 per cent. salt solution was used. MR. LAIST :-The reason for using salt in the solution is to get .the sulphur. The solution of dilute sulphuric acid has no solvent action on the sulphur even after roasting, and the addition of the salt is made primarily to dissolve the sulphur chlorides. MR. DICK:-I would like to ask also if you made any experiments as to grinding fine your calcines, rather than leaving the coarse material. MR. LAIST :-We have not made any experiments along those lines except in the laboratory, but the objections which we have to grinding are that the difficulties of roasting are very much greater when roasting finely ground material than when roasting coarse material, and the difficulties of leaching are somewhat increased; the percolating system is simpler and easier to manipulate, particularly when acid solutions are used, so that we prefer from our experience not to grind. STUART CROASDALE,* Denver, Colo. (communication to -the Secretary +) :-In order to meet the conditions involved in his ore-treatment problem, Mr. Laist has developed a very interesting and apparently successful metallurgical hybrid which he calls the oxychloridizing roast. The lower floors of the MacDougall furnaces are made to accomplish what used to be done on the " cooling floor" in the old days of salt roasting and " hypo " or brine leaching of silver ores.

Jan 11, 1913

By Matheus Fortes Stiborski

Este estudo descreve a aplicação de três métodos de cálculos teóricos pelos modelos matemáticos de Tafel e Sedlaczek, Siebel e Köster, com o objetivo de calcular o alargamento na laminação a quente de barras em aço AISI 1020 em um laminador tipo duo e definir quais dos modelos de alargamento se aproxima mais dos resultados obtidos experimentalmente. Foram utilizadas amostras com dimensões iniciais de largura (bo), 37,7 mm, altura (ho), 15,7 mm, e comprimento (lo), 300,00 mm onde se ajustou a luz dos cilindros para que fossem obtidas reduções aproximadas de 15% e 20% em altura. Os resultados obtidos indicam que o modelo de Siebel apresenta melhores resultados comparado com os valores experimentais.

Aug 16, 2017

By James H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER ACT) established a Technical Study Panel (The Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the Belt Evaluation Laboratory Test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 36- to 42-in wide conveyor belt. Due to today?s coal haulage capacity, the mining industry is using 72-in and wider conveyor belts. The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2010

The extent to which man's activities are influencing the earth's climate is subject to considerable debate. Internationally however, this debate has been put aside somewhat by the Kyoto Protocol. This international agreement is the political response to the threat of Global warming, predicated on the precautionary principle.NZ is seeking to be a leader in the Kyoto Protocol. Given our unique GHG emission profile and the structure of our economy, and the major uncertainties in both the science of climate change and the Kyoto Protocol itself, this desire to lead is absolutely inappropriate in this instance. We face a different, and often more severe, set of challenges in an economy that prices C emissions than virtually all of our trading partners. Unfortunately, these differences have not been reflected in climate change policy development to date. This represents a major threat to New Zealand's economy, wealth and jobs, particularly in the sectors that have been the core drivers of our economy over the last 20 years or so - agriculture, energy, primary processing. We do not, and should not, seek to avoid the issue but we must protect our economy and move with or follow our trading partners and competitors, not lead them.

Jan 1, 2002

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By S. Banisi, M. Poorkani, M. Farzaneh, M. Askari

"At the Sarcheshmeh copper mine 40,000 t of ore per day with an average grade of 0.9 % Cu is ground to 70% passing 75 microns. Grinding is effected in 8 parallel lines of 8 x 5 m ball mills in a closed circuit with cyclones. The make-up balls are 80-mm forged alloy steel balls and the average ball consumption is 750 gh of ore ground. In order to optimize ball size distribution inside the mill, based on the previous investigation instead of using only 80 mm make-up balls a combination of 80 and 60 mm (75% to 25% by weight) ball charge was used in one of the mills. To evaluate the performance of three ball types namely forged alloy steel balls (A), ductile cast iron (C), high chromium cast iron (D) and also a combined (80 and 60 mm) charge of forged alloy steel balls (B), four identical parallel mills were charged accordingly. These four mills were sampled during a period of six months. The amount of material finer than 75 microns of cyclone overflows was selected as a criterion for the performance evaluation. It was observed that in a mill with the combined make-up balls the amount of fine produced was 4% higher than the other mills. The consumption of ball types A, C and D were 730, 710 and 534 g/t, respectively. The results of laboratory flotation tests showed that due to an improvement in the production of fines an increase of 1.4% in the overall copper recovery is obtainable. Due to the promising results, the new make-up ball regime was implemented in all mills in the plant.INTRODUCTIONThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and has been processing 40,000 t/d of ore since 1982. The mine produces 100,000 tonnes of copper and 2,200 tonnes of molybednite concentrate per year. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailing constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83 and 87 % depending on the operating conditions and ore type."

Jan 1, 2002

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By Cláudio Orestes de Britto Filho

A exposição excessiva ao sol tem contribuído de forma significativa para o desenvolvimento de catarata, envelhecimento precoce, câncer de pele, agravamento de algumas dermatoses, dentre outras doenças, trazendo impacto negativo sobre a qualidade de vida dos indivíduos. Protetores solares, vestimentas e acessórios são frequentemente utilizados como forma de prevenção para os efeitos nocivos da radiação ultravioleta. No entanto alguns tipos de tecidos não proporcionam proteção suficiente. Novos produtos têxteis, com a incorporação de partículas de filtro solares inorgânicos, tem sido alvo de diferentes observações científicas. Esta pesquisa objetivou avaliar a eficiência de tecidos sintéticos, utilizados como filtro solar, cuja base do material é a poliamida. Os tecidos foram caracterizados pelos métodos de Microscopia Ótica- MO; Microscopia Eletrônica de Varredura –MEV; Espectroscopia por Energia Dispersiva (EDS); Difração de Raios X- DRX; Espectroscopia na Região do Infravermelho com Transformada de Fourier-FTIR e Calorimetria Exploratória Diferencial (DSC). Resultados mostram que com a incorporação da biocerâmica, mostram propriedades relevantes, contra os efeitos nocivos da radiação solar, quando comparados ao tecido sem incorporação da mesma. As roupas protetoras pode ser uma estratégia efetiva na proteção contra os danos causados pela exposição excessiva a radiação solar, durante a exposição a esse tipo de radiação.

Aug 8, 2018

By D A. Manhire, R M. Flores

The commercial develop of coalbed methane from the Powder River Basin has demonstrated that low-rank coals can be a viable source of gas. Currently over 20 000 coalbed methane wells exist in the Powder River and it is predicted that there will be 50 000 wells by 2010. What makes the Powder River Basin successful is the thickness of the coal (in excess of 30m) as well as the low ash content (

Jan 1, 2002

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process 1.2x0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm.

Jan 1, 2002

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today's apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery's capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

By Ricardo Rodrigues Grizotti

O trabalho tem por objetivo demonstrar o processo de implantação da ferramenta SAP Console (Rádio Frequência-RF) com utilização do Módulo de WM - Warehouse Management do SAP para a automatização das operações dos almoxarifados, visando agilizar com precisão o fluxo de informações, melhorando a operacionalidade do recebimento, estocagem, separação, distribuição, inventário, inspeção e preservação de materiais, promovendo a otimização dos processos e do espaço físico, pelo gerenciamento eficiente de informação e recursos, permitindo tirar o máximo proveito dessas atividades adotando diferenciais com a melhor aderência aos processos da ArcelorMittal Tubarão.

Jul 29, 2018