Search Documents

By Mostafa Benzaazoua, Bruno Bussière, Philippe Poirier, Denis Bois

"Environmental desulphurisation is an attractive alternative for the management of acid generating tailings. Non selective froth flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works (McLaughlin and Stuparyk, 1994; Bussière et al., 1995; 1998; Benzaazoua et al., 2000a,b; 2002). This process can reduce the volume of problematic tailings to manage, by making a sulphide fraction concentrate. The desulphurized tailings can then be used as a moisture retention layer in a cover with capillary barrier effects to prevent acid mine drainage.In this paper, the authors present the results from different laboratory and pilot scale flotation tests which confirm that low sulphide, non-acid generating tailings can be produced by froth flotation. It is also demonstrated that the sulphide concentrates obtained from desulphurisation, when mixed with binders gave good long term results in terms of mechanical behaviour, thus demonstrating that the sulphide fraction can be used for paste backfill material. From previous work (Bussière et al. 1998, 1999) on the evaluation of the operating and capital costs of the desulphurisation process for different ore types, the use of desulphurized tailings to create a dry cover was then studied for several scenarios. The desulphurisation process was compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation and the advantages and disadvantages of desulphurisation are presented as well as the costs of this method of AD prevention.INTRODUCTIONThe principal environmental problem of the mining industry today is the generation of acidic drainage (AD) resulting from the natural oxidation of the sulphides in mine tailings. This phenomenon involves the generation of acidity which increase the amounts of toxic metals in the waste water released into the environment by a mine. The environmental impact of the AD has been described in detail in previous work (e.g. Down et Stocks, 1977; Ritcey, 1989; Gray, 1997; Ripley et al., 1996; Aubertin et al., 2002)."

Jan 1, 2004

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003

By James A. Brown, Marius Botha, Christopher A. Fleming

"The technical and economic feasibility or re-processing hundreds of millions of tons of tailings in a number of historic gold tailings dams in the Witwatersrand area of South Africa is being investigated. The objective is to recover uranium and residual gold from the tailings, as well as to oxidize the sulphides to eliminate long term environmental liabilities associated with acid mine drainage. The tailings from the re-processing plant will be re-deposited in a new area far from urbanization, allowing for the rehabilitation of the real estate currently occupied by these historic tailings.The first step in the process involves a mild-regrind and mild acid leach of the tailings (pH 2.5 to 3.0) to dissolve up to 40% of the uranium. This uranium is recovered directly from the pulp by resin in pulp (RIP) with a strong base resin. The RIP tails are then treated by flotation to recover a rougher pyrite concentrate, and flotation tailings that are discarded. The rougher concentrate is cleaned to produce a final pyrite concentrate and cleaner scavenger tailings, and the pyrite concentrate is oxidized in an autoclave to leach uranium and generate acid. The autoclave discharge is combined with the cleaner scavenger tails, and the acid and ferric ions generated in the autoclave are used to leach more uranium and oxidize more sulphide in the cleaner tails. The product from the concentrate leach circuit is processed by resin in pulp for uranium recovery, followed by neutralization, cyanidation and carbon in pulp for gold recovery.The rougher float tails may be further treated to recover gold that was not recovered in flotation, but which had been liberated from the old dumps by natural oxidation of some of the pyrite over many decades. The float tails would be neutralized and treated by cyanidation and CIL to recover this liberated gold.All parts of the flowsheet have been extensively tested in the laboratory, and the critical elements of flotation, pressure oxidation and resin in pulp have been demonstrated in pilot plants. The results of the hydrometallurgical investigations are presented here."

Jan 1, 2010

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

Though many mining and mineral processing companies have embraced the principles of sustainable development (SD), there is still a significant challenge of applying these in a practical sense, either in plant design or as part of day-to-day operations. The high-level nature of sustainability concepts often do not translate easily into workable activities or business case evaluations. This makes it difficult for engineers and company decision makers to understand whether their actions are making a contribution to sustainable development and a long-term business case. While several organisations have their own SD tools that can, to a degree, help identify these opportunities, they are largely ad-hoc and lack the necessary thoroughness to defensibly value these opportunities. Recognising these serious shortcomings, the Cooperative Research Centre for Sustainable Resource Processing (CSRP) has undertaken the development and trial applications of SUSOP« (SUStainable OPerations), a new concept that is somewhat analogous to HAZOP and the wider risk and safety frameworks used in projects today. The key goal of the SUSOP« research project is to produce a holistic, systematic and rigorous framework for project development, capturing, recording and evaluating SD opportunities and constraints against a chosen sustainability structure (eg Five Capitals). SUSOP« is being developed through an iterative process with input from research institutions and engineering companies. This integrated approach ensures that SUSOP«, in its final form, will have the academic rigour and industry realism required to assist the resource sector contribute to societal sustainability by embedding the concepts and processes into the design and operation of their assets in a meaningful and practical manner. SUSOP« has created much traction with both engineering companies and mining and minerals operators. This conference paper presents an overview of the SUSOP« framework and its current suite of processes as well as highlighting, through practical case studies, its capability to incorporate SD considerations at different phases of an engineering project's development.

Jun 1, 2010

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2005 draws upon available information from literature, industry and U.S. Geological Survey (USGS) specialists. It provides data on exploration budgets by global region and mineral commodity and identifies significant mineral discoveries and exploration target areas. It also discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based on these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2005. They include budgetary statistics provided by Metals Economics Group (MEG) and information on regional and site-specific exploration activities in 2005 compiled by the USGS.

Jan 1, 2006

By Brandon Axelrod

This paper follows a student’s interest in explosives which began at an early age after watching a television program highlighting explosives engineering. The use of explosives in those programs led to curiosity about how one gets involved in the industry. These programs enticed the author to further investigate the explosives industry leading him to an explosives camp for high school students. After attending the camp, this passion further developed into postsecondary education.

Jan 1, 2015

By J. D. McAteer

It is widely agreed throughout the mining community that federal mine safety and health legislation administered by the Mine Safety and Health Administration (MSHA) deserves significant credit for the past quarter-century's remarkable improvements in miner safety and health. Recently, however, it has been suggested that the mining industry in the United States has now evolved to a point that current mine safety and health law may be obsolete. This proposition deserves attention. Today, I propose to give it the close logical scrutiny that is its due. I conclude that the obsolescence of current mine safety and health law is not supported by the evidence. The existing mine safety and health law continues to serve as a critically important supplement to mine operators' safety programs at a modest cost to the taxpayer. At the same time, trends in a changing industry do call for responsive adaptations in the Federal mine safety and health program. I will argue that timely and appropriate responses to changing needs can be accomplished within the framework of existing legislation, provided federal officials avail themselves of the flexibility provided by existing law.

Jan 1, 1996

By Tuncel M. Yegulalp, Anuta Belova

This paper expands on the ZECA (Zero Emission Coal Alliance) technology, which is aimed at making coal a sustainable source of clean energy in the near future. The technology proposed immediate capture of carbon dioxide and other pollutants upon generation, thus alleviating their negative effects in the Earth’s atmosphere. ZECA proposes using chemical energy of coal to produce hydrogen; the latter is then used to produce electricity via fuel cells or Hyrogen-Oxygen turbines. In this study, a chemical engineering package, AspenPlus 12.1, is used to simulate the reactor (reformer) in which hydrogen is produced from methane water and lime as part of the zero emission power plant. Thermodynamic conditions, pressure and temperature, are optimized with respect to molar hydrogen production. Under the proposed conditions, molar conversion efficiency, carbon to hydrogen, of 95% is achieved. Further studies are required to model the complete power plant and to optimize it for efficiency.

Jan 1, 2005

By Nick D. Rose

Outline ?Background ?History of inverse-velocity for failure prediction ?Methodolog ?Case Histories ?Three case examples of predicted slopefailure to actual date of occurrence ?One case example of mitigated slope failure using inverse-velocity to forecast failure time and schedule remedial measures ?Conclusions

May 1, 2006

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By O. N. Sikazwe

The Nchanga Cu-Co ore deposit of the Zambian Copperbelt, is hosted in Neoproterozoic siliciclastic-carbonate sedimentary rocks, and it consists of two orebodies: the Lower Orebody (shale) and the Upper Orebody (arkose). Refractory Cu ores present in the Upper Orebody comprise 150 Mt with average 0.87% Cu, and are characterized by inadequate recovery of copper by leaching. This materials characterization study, conducted on refractory ore samples from the Upper Orebody using optical microscopy, QEMSCAN®, and microprobe, has shown that copper occurs mainly in biotite, phlogopite, malachite, pseudomalachite and goethite. QEMSCAN® has quantified the abundance of each phase and total Cu deportment in each phase.

Jan 1, 2008

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys' a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

By A. Hiltunen, R. Hiltunen

The utilization of blast furnace and BOF slags has long traditions and well-known applications in the building and road construction industries and in soil conditioning. The starting point for product development has been the basic physico-chemical properties of slags. This development has led to the almost 100% utilization of blast furnace slags and also considerable amounts of steel slags. While new methods and applications are continuously being looked for and developed in order to recycle and utilize all types of slag, there is at the same time an increasing debate over the exact nature of the slags, whether they are products or waste material, and whether they should be considered substances or preparations. These questions have emerged as a consequence of the environmental effects of the slags and current environmental legislation. The environmental effects of slags can be seen to be both beneficial and less beneficial. There is no doubt about their benefits in the road construction industry, as they allow significant savings in terms of natural materials and in transportation. It is also a known fact that using slags as fertilizers and in the cement industry leads to reduction in CO2emissions. The less favourable effects are the possible harmful emissions into the soil and groundwater. In this paper we describe the properties of slag products and their environmental effects according to investigations carried out in Finland. Keywords: utilization, blast furnace slag, steel slag, properties, solubility, environment

Jan 1, 2004