Search Documents

By Llewellyn A. Rubin

ROUTINES AND SUBROUTINES A- 1 Wait Loop (Wait) A- 2 Receiver Processing (RCVP) A- 3 Control Panel Sequence (CPNL) A-4 Interrupt Routine (INTRP) A- 5 Math Processing Routine (PROC) A-6 Input Constants for Math Routine (CONI) A-7 Angle Conversion Routines (LVERT) A- 8 Display Routine (DSPY) A- 9 Message Print Auxillary Routine (MESSO) A-10 Auxillary Subroutines (AFUTC and AGETC)

Jan 1, 1973

By J. D. Appleton, J. Ridgway, K. B. Greally

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The results suggest that meaningful geochemical maps can be produced from very low-density surveys, and that existing data sets could perhaps be incorporated into such a map series with the use of a system such as Uniras software. There are still many problems to be resolved, however, including the compatibility of data derived from different analytical methods, and the precise methods to be employed will necessarily require international agreement. Sampling densities should be chosen on the basis of the scale of the geochemical and geological features to be distinguished and will vary from region to region. Reanalysis of selected samples from archives to increase the range of elements determined or to unify analytical methods is only likely to be effective if the original survey was at quite a low density

Jul 1, 1991

By G. K. Rogers

The portal, which is the near-horizontal, surface point of entry to an underground excavation, can often be an exceedingly difficult area in terms of ground control. Surface and subsurface failures at portals, as discerned during a study involving over 300 case histories, are unfortunately, common. To aid in the engineering evaluation of portals, the Geomechanics Classification System was appended with discontinuity orientation assessment values and support/excavation guidelines. Also, a design model utilizing RMR predicted rock loads in conjunction with half-dome theory is proposed for the most common type of portal failure. Other pertinent comments and recommendations relating to portal stability are included.

Jan 1, 1989

By Gregorio Llanos Villarreal

Dado que la expansión progresiva de la mina Calera exige una productividad de material detrítico, se ha optado por una alternativa de voladuras a gran escala que controle el desmonte proveniente de los desarrollos de la mina. En esta perspectiva, el presente estudio refiere las experiencias de voladura adquiridas en la mina Calera, a partir de la aplicación de "voladuras de coyote" a gran escala. La eficiencia de sus resultados redujo la utilización de los equipos pesados en la cantera de relleno, así como los costos de los conceptos.

Apr 1, 1991

By Solomons S. S, Tillmann V. H

The progress of longhole open stoping (LHOS) at Zinc Corporation Limited and New Broken Hill Consolidated Limited (ZC/NBIIC) is described together with the design of a novel sloped wall longhole stoping method which should allow the complete extraction of the orebody without the formation of pillars and with minimal dilution of the ore with sand fill.

Jan 1, 1981

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

1. Paper1?Identification and enumeration of asbestos fibers in the mining environment: mission and modification to the federal asbestos standard Arthur M. Langer Asbestos-related disease is increased with cumulative exposure (the concentration of asbestos in the air and duration of exposure). The maximum duration is assumed to be a working lifetime so federal agencies control cumulative exposure by limiting the airborne concentration of asbestos fibers equal to or greater than 5 lm in length. Air samples are collected in the environment of interest by entraining the airborne particulates including fibers on membrane filters and then counting the number of fibers using phase-contrast light microscopy. In addition to length, the fibers must have a length to width ratio of at least 3 to 1. This ratio is also referred to as the aspect ratio. Some counting strategies placed an upper limit on the fiber width restricting the counting to respirable fibers. Airborne asbestos is controlled by monitoring a sub-population of the airborne asbestos. No asbestos fibers shorter than 5 lm or fibers of any length having widths less than the resolution of the light optical method are counted. In the non-occupational environment, the Environmental Protection Agency requires the use of analytical transmission electron microscopy and fibers and counting fibers with lengths of 0.5 lm or greater and aspect ratios of 5 to 1 or greater are counted. The permissible exposure limit for asbestos has been reduced by more than 120-fold since 1969, when the standard was 12 fiber/ml and the current monitoring methodology was developed. The manufacturing and mining worksites are regulated by two different federal agencies and the asbestos exposure limit was higher in the mining environment until recently (Mine Safety and Health Administration 30 CFR Part 56, 57, and 7, Federal Registry, February 29, 2008). Currently the permissible exposure limit (PEL) is the same in both types of workplace and it is 0.1 fibers per milliliter (fiber/ml) over an 8-h shift as a time-weighted average (TWA). A milliliter (ml) is equivalent to a cubic centimeter (cc) and sometimes this standard is reported as 0.1 f/cc. As the phase-contrast methodology was used to monitor lower exposures and environments, other fibrous mineral particulates were incorrectly characterized as asbestos. These occurred in talc deposits and taconite ores from the Eastern Mesabi Range.

Jan 1, 2008

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

This report is in partial fulfillment of Contract S0241051 awarded to COMINEC on June 27, 1974. 'Me purpose of the work under this contract is to develop a conceptual design for an automated longwall mining system. The conceptual design will serve as the basis for future design and development of an automated longwall mining system capable of sustained production in excess of 2,500 tons per shift with reduced manpower which will ultimately be demonstrated in an area where conventional longwall mining has been successful. 1.2 DEFINITION OF THE PROBLEM 1.2.1 Why An Automated System The most obvious benefit of automation and remote control in a longwall mining system is the reduction of accidents consequent upon a reduced working force in the hazardous face areas. However, another important aspect of the problem is the skilled labor shortage which is being compounded by the need for vastly increased coal production. The United States coal mining industry had a working force of almost 600,000 miners in 1928 but was able to muster only 145,000 miners in 1970. The miners required to staff the additional working sections and the new mines necessary to meet our energy needs are simply not available. Only automation and remote control will permit a reduced work force with increased production by keeping the face equipment operating continuously.

Jan 1, 1975

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

Hatches Creek has been inactive since 1961, but with better metal prices, interest in the field is reviving.The mixed gravity concentrates which were unsalable in 1951 have been experimentally separated into salable wolfram, scheelite, and bismuth-gold concentrates, and a flow sheet incorporating magneticseparation and flotation has been developed.

Jan 1, 1965

FOR rapidly marking in geological and topographical features on parish plans, the author has used the Veeder cyclometer with very satisfactory results. A simple Veeder cyclometer, usually retailed at cycle depots at 4s., is fixed to the axle of the front wheel of an ordinary bicycle. The cyclometer is desigued to read in miles and tenths of miles, which are recorded through gearing actuated by a striker on a spoke of the bicycle wheel engaging one of the vanes of the cyclometer once every revolution.By using 80 strikers the reading would be in chains and tenths of chains; therefore the use of 8 strikers gives the reading in chains, utilizing all the figures. The cyclometer is designed to be placed on the right-hand side of the bicycle, and takes up a minimum of space, being only about the size of the top joint of the thumb. With some makes of cycles there is insufficient clearance, so the cyclometer must then be placed on the left side, and the 8 strikers made to engage the top vanes, as shown in the sketch (Fig. 1).Very accurate readings can be obtained by this instrument. The author has found by numerous tests that the maximum error...

Jan 1, 1916

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1990. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1991

By Aquiles Vivar

Ante los problemas de sismicidad inducidos por el sistema de minado en la Compañía minera Milpo, se planteó una solución a través del sistema de monitoreo sísmico único, donde se da una distribución espacial de 20 censores entre uniaxiales y triaxiales distribuidos en 3 niveles de producción en el área de influencia de las actuales operaciones para así ubicar, cualificar y cuantificar el fenómeno a efectos de realizar los análisis interpretativos del caso. En ese sentido, el presente texto describe el sistema de monitoreo, cuyo software sísmico está diseñado para determinar nuevas estructuras formadas a partir de los eventos sísmicos pre existentes reactivadas por la sismicidad inducida, así como el desarrollo de planos de isocontornos que permiten la diferenciación entre zonas de altos y bajos esfuerzos.

Sep 9, 2007

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

"The Code was developed in 2004 through the Collaboration Agreement between Institution of Mining Engineers of Chile (IIMCh) and the Ministry of Mining (Chile) in Dec 2002. It is an amalgamation of current practices with respect to standards and procedures for exploration prospects, mineral resources, and reserves for the purpose of public reporting. Certification is required to prepare and issue information on mineral assets according to the guidelines that regulate the technical, economic, and environmental aspects that satisfy the conditions set by the Chilean capital and financial markets.The Mineral Resources Committee of the Instititution of Mining Engineers of Chile (IIMCh) is pleased to introduce theCode for the Certification of Exploration Prospects, Mineral Resources and Reserves which is the result of a Collaboration Agreement between the IIMCh and the Ministry of Mining established in December, 2002.This code synthetizes the present practice of the mining industry in regard to standards and procedures applied to exploration prospects, mineral resources, and reserves with the purpose of reporting publicly on financial instruments based on these mine assets in the capital markets. These standards follow general criteria already adopted and applied by capital markets in those countries characterized by a very dynamic and well developed mining sector such as Australia, Canada, Southafrica, United Kingdom, and others. The work done by the Mineral Resources Committee of the IIMCh has had the recognition of the Combined Reserves International Reporting Standards Committee (CRIRSCO) that leads the establishement of an international code in these matters. CRIRISCO is an entity formed by representatives of the countries previously mentioned, a representative of the Society of Mining Engineers of the UStates and a representative of the IIMCh. The Institution thanks the Ministry of Mining, the representatives of these Ministry in the Mineral Resources Committee, and specially the Minister of Mining, Sr. Alfonso Dulanto Rencoret due to the genuine support given to the IIMCh in the preparation of this Code.The Institution also thanks the Superintendencia de Valores y Seguros (SVS) because of the help given continuously to the Committee as well as by the interchange of opinions and suggestions received during the preparation of this document."

Jan 1, 2003

By H. F. Yancey, E. Zane

"INTRODUCTION The term ""friability"" as applied to coal may be defined as the physical property of coal which expresses its tendency to become reduced in size during handling as a result of such external forces as impact and attrition. Thus friability is a quantitative concept and property, and hence can only be defined in relative terms or in terms of measurement. Methods of measurement are difficult to formulate and apply because coal is anything but homogeneous in physical structure and chemical constitution. aMoreover, friability itself is a composite property obviously dependent upon a group of other specific characteristics such as cleavage, fracture, tenacity, hardness, and elasticity, which vary from coal to coal with change in rank and even between individual coals of the same rank. These characteristics affect the friability values of different coals to varying degrees, but this fact does not impair the usefulness of and the need for friability measurements.The amount of breakage or degradation in size that a coal suffers in mining, preparation, and subsequent handling depends upon its inherent friability and the severity of the handling treatment which it receives from the time it is taken from the bed until it reaches the consumer. The value of the coal to the producer and jobber depends in large measure upon these same factors--friability and severity of treatment—because the larger sizes still command a premium in the ordinary market. Although much has been accomplished by the coal-producing industry in minimizing the breakage of coal in mining and preparation, it is apparent that additional reductions in breakage must await further improvements in design of coal-handling equipment. Such improvements will result from more intensive investigations of the extent of breakage or degradation in size occasioned by specific mining and handling operations and the development and application of standardized methods of evaluating friability.The work described in this report was undertaken to assist in the development of standard methods for evaluating the friability of coal. Specifically, the work deals with a Comparison of the various methods previously proposed for estimating the friability of coal and coal products. This same objective is now being sought at a number of other institutions, both in the United States and Canada, by a committee of the American Society for Testing Materials. It is believed that by providing additional information concerning a property of coal pertinent to its increased usefulness, the work described will supplement and increase the useful of the data which long have been, and still are being, furnished by the bureau of Mines on the composition of coals of the United States."

Jun 1, 1933

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978

Helium has probably aroused more varied scientific curiosity than any other single element. Discovered by spectroscopic examination of the sun during an eclipse in 1868, helium is now known to exist not only in the sun and other stars but on earth occluded in minerals, accumulated with natural gases in pockets in the earth's crust, and in the atmosphere surrounding the earth. Astronomers study its presence in the various stars of the universe for clues to their origin and history. Geochemists and geologists study its occurrences in rocks, minerals, and meteorites to determine the age of the earth and the manner of its formation. Pathologists study its effect on living tissues in search for the ideal combination with oxygen for artificial breathing mixtures in medicine, diving operations, and space vehicles. Chemists study its physical properties and use it to trace the sequence of events in reactions in which it does not participate. Geneticists and bacteriologists use it for special studies. Physicists study its behavior when liquefied and the behavior of materials cooled to nearly absolute zero by its use. Nuclear physicists learn more about the universe through study of the nuclear reactions that produce it. Through study of helium and greater knowledge of its origin and properties, science continues to unlock some of nature's more closely guarded secrets. Unknown on earth before 1895, and not discovered as a minor constituent of natural gas until 1905, helium with its simple atomic structure--a nucleus with two electrons orbiting in a closed shell--is a unique element. It is next to the lightest gas, only hydrogen is lighter. It occupies position number 2 in the Periodic Table of the Elements and heads the list of so-called "rare" or ?noble? gases. Most of the naturally occurring helium has an atomic mass of 4.003874 (oxygen = 16). A trace (1.7 x 10-5 mol percent) is the light isotope helium-3 whose atomic mass is 3.0169800 Unstable isotopes of mass numbers 5 and 6 have been authenticated. Isotopes of mass numbers 7 and 8 have been reported, but their existence is less well established. All the heavier isotopes are radioactive and are the product of nuclear reactions.

Jan 1, 1968