Search Documents

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Leandro Brunholi Ramos

Foi estudado o efeito da temperatura no comportamento à corrosão sob tensão do aço inoxidável dúplex AISI 318 em solução contendo 115.000 ppm de cloreto, pH4 a temperatura ambiente e a 70°C. Ensaios de tração com baixa de taxa de deformação foram realizados. Foi avaliada a susceptibilidade do aço inoxidável dúplex AISI 318 à corrosão sob tensão no potencial de circuito aberto e em vários potenciais anódicos e catódicos. Os resultados mostraram que a redução do alongamento variou com o potencial aplicado. Os resultados experimentais mostraram que o aço AISI 318 ficou imune à corrosão sob tensão em potencial entre -750 mVECS e 1.000 mVECS na temperatura ambiente e entre -650 e -100mVECS para a temperatura de 70°C. Em potenciais maiores que o potencial de pite observou-se uma redução drástica no alongamento em ambas as temperaturas. No entanto, quando os potenciais aplicados foram abaixo de -650 mVECS para a temperatura de 70°C e -750mVECS para a temperatura ambiente, houve uma redução no alongamento final até a ruptura, provavelmente através do processo de fragilização por hidrogênio.

Aug 8, 2018

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

La voladura es la herramienta económica más efectiva para fragmentar y mover rocas. Sin embargo, no puede ser empleado cuando un patron de voladura mal diseñado, ya que se genera un descontrol sobre la energía liberada. En este sentido, el presente texto describe el empleo de la prospección fotogramétrica estéreo y los sistemas de prospección de pozos en una operación de voladura en la cantera brasileña Incopel.

Apr 1, 2013

By B. F. Giyani, A. Salama

Tanzania is a country with a variety of mineral deposits, including metallic minerals, gemstones, mineral fuels, industrial minerals, and critical minerals. This study provides an overview of mining legal framework, mineral occurrence and production, challenges in the mining sector, and government initiatives. The aim is to demonstrate the development of the mining sector in Tanzania and explore the potential for further mining investment in the country. The mineral production data showed generally increasing trends over the years, for example, gold production increased from 42 tonnes in 2018/2019 to around 50 tonnes in 2023/2024. Despite the growth, the mining sector encounters several challenges, including a lack of detailed geological information on mineral deposits, inadequate infrastructures in some remote mining sites, the existence of informal artisanal miners, and mineral smuggling. The Tanzanian government has introduced several initiatives to address these challenges, including carrying out the highresolution airborne geophysical survey to increase geological information in some areas, the formalisation of artisanal and small-scale mining, establishing mineral markets to combat mineral smuggling, and encouraging mineral value addition within the country.

Oct 24, 2025

By Patrícia de Fátima Rodrigues

Neste trabalho, a técnica de ensaios de torção a quente foi utilizada na simulação física do processo de laminação a quente do produto fio-máquina. Foram realizados ensaios em dois tipos de aços, a saber, um aço baixo carbono (BC) e outro aço ultrabaixo carbono (UBC). A realização dos ensaios de torção a quente, sob condições próximas ao processamento industrial, ou seja, utilizando parâmetros de processo como taxa de deformação, temperatura e tempo entre passes, fornecidos pelo fabricante do laminador, possibilitou evidenciar os mecanismos de amaciamento destes aços. Foram obtidas as curvas de escoamento para as condições propostas e realizadas análises metalográficas para avaliar as microestruturas resultantes. A partir dos resultados obtidos pode-se concluir que ambos os aços apresentaram bom desempenho na laminação do fio-máquina. Em particular, o aço ultrabaixo carbono mostrou-se capaz de suportar as condições de processamento impostas nas simulações, o que torna viável sua possível aplicação no mercado de produtos de aços longos.

Aug 16, 2017

By Sandra Villacorta

"El presente trabajo describe los aspectos geoambientales de la cuenca del río Huaura, ubicada al norte de la región de Lima con el fin de establecer una línea de base geoambiental. Dicha cuenca destaca por la actividad agroindustrial, la minería representada por minas como Raura y Ucchucchaucua, la presencia de áreas geoturísticas como los baños termo-medicinales de Churín y los centros poblados como Huacho, Huaura y Oyón. La caracterización geodinámica y el análisis de susceptibilidad a movimientos en masa e inundaciones, han permitido establecer que las zonas más susceptibles a estos procesos se encuentran en los distritos de: Sayán, Naván, Andajes, Pachangara, Oyón, Maray, Santa Leonor, Caujul, Huaura, Huacho, Leoncio Prado e Ihuarí. En este sentido, el estudio geambiental señala que la zona más impactada está ubicada en Caujul (alrededores de la mina abandonada Santa Rita) y que se debe monitorear los siguientes sectores: Uchucchacua, Churín e Iscaycruz en Oyón; y Vilcahuara, Sayán, Huamboy Grande, Chiuchín y Huacho, en Huaura; donde en algunos casos se ha superado los límites permisibles para aguas y sedimentos de normativas internacionales, e igualmente se ha registrado disposición de residuos sólidos a la intemperie, salitrización de los suelos por uso de insecticidas en actividades agrícolas, vertimiento de gases tóxicos de las actividades agroindustriales y disposición inadecuado de desmontes de construcción o de mina."

Sep 14, 2009

By T. B. Nolan, R. N. Hunt

In terms of present metal prices, analysis of extant records of the Eureka district indicate past production of the magnitude of $200,000,000 in recovered silver, lead, and gold. Production to date has been thoroughly oxidized ore from massive replacements, fissures, manta, and pipe-like bodies-in large part from the massive Eldorado (middle Cambrian) and Hamburg (middle to late Cambrian) dolomite horizons. In the productive area of about 6 square miles carbonate rocks comprise 80 per cent of the section, which includes early Cambrian to late Ordovician horizons. Four-fifths or more of the district's production came from a block of Eldorado dolomite in Ruby Hill that was moved in over younger horizons on strands of a regional thrust fault. The lower 500 to 600 feet of the block was much fractured and brecciated and became host to the ores. The Ruby Hill fault, a late normal fault, limits the Ruby Hill block of dolomite on the north for its entire length of nearly a mile and terminates the downward extent and exploitation of its ores. It introduced an hiatus of some 40 years in the district's development. Drilling of the past 20-odd years, followed by underground work, has now exposed the down-faulted extension of the Ruby Hill block of Eldorado dolomite and its contained ores, dropped 1800 feet in a dip shift to depths beneath the surface of 2000 to 3000 feet. The ores at depth are the sulfide counterpart of those mined in early years on the footwall side of the fault. The ores of the district may be attributed to the same source as the intrusive quartz diorite outcropping in a limited way south of Ruby Hill but found at depth elsewhere in drill holes. The long north-south axis of the district, its anticlinal structure, its major faults, and the distribution of the intrusives and, in their relation to the surface, the ores themselves, all suggest that erosion has not cut deep enough to expose the extent of intrusives and the ores consequent upon them.

Jan 1, 1968

By Joseph Mcavoy

El presente artículo señala a la excavadora terrestre más grande del mundo, como el tributo tecnológico de maquinaria moderna, el cual fue. construida por la empresa Bucyrus-Erie para la compañía Ohio Power, que forma parte del American Electric Power System, y costó 24 millones de dólares. La 4250-W, apodada "~ran Muskie", por la mina Muskingum en que trabaja, entró en servicio el año 1969, en las aderas de Cumberland, cerca de Zanesville, Ohio.

Jan 1, 1971

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By J .. Vargas Fernández

El presente trabajo señala la importancia del hombre en la productividad minera a través del desarrollo del plan de minería, el cual comprende los proyectos de inversión de los sectores públicos y privados, la explotación de las minas no trabajadas, el uso eficiente del capital proveniente de recursos propios y la competencia mundial. Así también se describe el conocimiento del potencial minero, productividad minera (reservas, rendimiento), niveles de formación, productividad de los dirigentes mineros y las acciones para el incremento de dicha productividad.

Nov 20, 1972

Anaconda Aluminum Co. began production from a new 60,000-ton-per-year potline at Sebree, KY, which brings the total capacity of the plant to 180,000 tons per year. A strike by workers at Alcan Aluminium Corp. primary aluminum smelters at Arvida, Que., Isle Maligne, Que., and Beauharnois, Que. shut down the plants and the company announced force majeure on part of its ingot supply commitments. Kaiser Aluminum and Chemical Corp. announced plans to increase its price for primary aluminum from 60.0 cents per pound to 63.0 cents per pound effective July 1.

Jan 1, 1979

By Eduardo Gimenes Jabes, Thiago Pires Nagasima, João Ricardo Filipini da Silveira, João Batista Ferreira Neto, Marcelo de Aquino Martorano

Foi implementado um modelo matemático para simular a solidificação de ligas do sistema Nd-Fe-B no processo de lingotamento de tiras. O modelo foi baseado na aplicação da equação de condução de calor unidimensional através da espessura da tira e da parede do rolo refrigerado da máquina de lingotamento. A resolução numérica dessas equações permitiu o cálculo do perfil de fração de sólido através da espessura da tira e dos perfis de temperatura através da tira e da parede do rolo. A temperatura de um ponto da superfície do rolo oscila em ciclos formados pelo contato com o metal líquido (vazamento) e pelo destacamento de um pedaço da tira. A temperatura média do rolo aumenta continuamente, diminuindo a taxa de resfriamento nas tiras. Mesmo no início do processo, os pedaços de tiras que se destacam ainda não estão completamente sólidos.

Oct 1, 2019

By Murray Udy

La Corporación Venezolana de Guayana ( CVG) decidió renovar su noveno horno eléctrico de reducción a través de un nuevo proceso para la fabricación del fierro Strategic-Ud. En este sentido, el presente artículo señala la la instalación de este nuevo proceso de producción de hierro en la planta siderúrgica del Orinoco. La implantación del Strategic-Udy se inició en 1963 y es una combinación de operaciones unitarias conocidas con una técnica operativa mejorada, a fin de ofrecer mejor control sobre los procesos químicos e incrementar la eficiencia de la técnica antigua. Asimismo este nuevo proceso, elimina las limitaciones de tamaño y calidad del material impuestas en los procesos existentes para la fabricación del fierro.

Jan 1, 1964

By Kenneth Wardell

Those flat lying, bedded or replacement, non-fossil fuel deposits which exist within the U.S.A., and which are amenable to longwall mining, are identified by reference to three principal factors associated with their physical/geological environments. These are their depth, extent and structural continuity. Technical feasibility is assessed in relation to the likely cutting speeds which can be achieved in the identified minerals with existing longwall shearer machines. Economic comparisons are made between traditional mining operations in those deposits for which technical feasibility is demonstrable. Continents are made concerning those technical deficiencies which appear to preclude the application of existing longwall equipment to the identified deposits and suggestions are made regarding the lines of research aimed at improving longwall technology.

Jan 1, 1978

By Robert B. Hoekzema

This Bureau of Mines report describes the history, characteristics, distribution, and mineral development potential of 21 lode gold deposits in or near the Chugach National Forest (CNF), AK. It includes findings from a 4-yr (1979 to 1982) mineral evaluation of the CNF conducted by the Bureau and the U.S. Geological Survey (USGS). This evaluation, undertaken to provide the U.S. Forest Service with mineral resource data for use in making decisions on land use, included site-specific mapping and sampling of more than 200-lode gold deposits. The data presented here were compiled from the findings of this 4-yr evaluation and from existing literature. Fourteen of the 21 lode gold deposits described in this report contain a combined identified resource of 117,750 short tons (st) averaging 0.55 oz/st Au and 0.2 oz/st Ag. Two mineralized felsic dikes in the Summit Lake-Palmer Creek area contain a combined identified resource of 18 million st grading 0.02 oz/st Au and 0.16 oz/st Ag. Identified resources were not determined for the remaining five deposits because of a lack of information.

Jan 1, 1987

By Bill Mariucci, Gary Almeraris

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2009

By Rafael Oliveira Sena

A SMS Siemag tem oferecido ao mercado brasileiro novas tecnologias para Lingotamento Contínuo de Placas com objetivo de aumento de desempenho dos equipamentos. A SMS Siemag tem desenvolvido e otimizado o processo de revestimento de placas de cobre do molde que utiliza em conjunto com o processo de eletrodeposição a tecnologia thermal spray que proporciona um produto com alta propriedade de resistência ao desgaste. O revestimento cerâmico, mais conhecido como UniGuardTM, tem obtido resultados excelentes no mercado da América do Norte atingindo valores superiores a 300.000 toneladas. A utilização do revestimento UniGuardTM proporciona um aumento de produtividade e redução dos custos de manutenção do molde bem como redução de aquisição de novas placas de cobre.

Jul 29, 2018

By Mario Samamé Boggio

El presente texto señala las energías convencionales y no convencionales en Latinoamérica. La utilización de la energía nuclear se plantea técnicamente en función de la fisión nuclear y de la fusión nuclear. La fisión nuclear consiste en la reacción por la cual los núcleos de un átomo pesado se escinden en dos aproximadamente iguales, produciendo isótopos de los elementos más ligeros acompañados por la emisión de neutrones. La fusión nuclear es en esencia lo opuesto a la fisión o escisión: se combina o "sueldan" dos núcleos ligeros formando un núcleo más pesado; el nuevo núcleo no pesa igual que los dos núcleos juntos. La fusión libera enormes cantidades de energía a elevadas temperaturas.

Jul 1, 1978