Search Documents

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002

In both exploration and mining, the laboratory is often seen as a cost rather than a profit centre. The aim in most mining companies is to increase profits by reducing costs, so the budget for the laboratory is under constant pressure.There is another option; to see the laboratory as the brain of the operation. By lifting the status of the laboratory and treating it as a profit centre, mine costs may be reduced in other ways, e.g. reduction in milling costs. This change of status will require investing more capital in better equipment, more training for employees and more employees to carry out project research.There are many examples of major costs being incurred because of inadequate laboratory work. Conversely, by spending more money on laboratories and their activities, overall costs can be reduced or profits enhanced.

Jan 1, 2002

By K Dudley, D Readett

The design of entrainment control processes in copper SX plants has been studied by use of models based on achievable plant performance. A number of alternatives have been assessed for their suitability in minimising the transfer of deleterious species from PLS into the electrolyte. The position of the wash (scrub) stage in the circuit, either before or after the loaded organic tank, has been the subject of considerable debate. The modelling shows that at ænormalÆ entrainment levels, the performance of the circuits are very similar. However at high entrainment levels the selection of the wash after the loaded organic storage has significantly lower transfer of contaminants. When considering the inclusion of a loaded organic coalescer the results of the modelling again show that the best circuit has the loaded organic storage/coalescer before the wash stage. The overall control of EW contaminants includes both a wash stage and an EW bleed flow. The total water use for these two flows is shown to go through an absolute minimum. The minimum flow rate is not greatly dependant on the total entrainment from the SX settlers. This can be a useful operating strategy if the quantity of high quality water for make up is limited by the capacity of the water treatment plant (eg RO). However the minimum cost option is to maximise the flow of water to the wash stage and minimise the EW bleed stream. The main driver for this is the cost of the cobalt sulphate contained in the electrolyte. Some results from the latest circuit modifications at the Nifty and Girilambone Copper Projects are presented to confirm the benefits of using both coalescing systems and a wash stage. The EW bleed has been reduced to a level that is less than the loss internally in the SX stage to stage entrainment. There has been an occasional need to add chloride to the EW to maintain sufficient concentration to act as a growth modifier.

Jan 1, 2002

By V. A. L. Breguncci, A. H. Martins, C. P. Ribeiro Jr.

This work presents experimental results for the recovery of gold present in alkaline cyanide solutions by using the electroelution technique of strong-base anionic polymeric resins IRA 402-CL from Rhom and Haas-Brazil Ltd. loaded with gold. This technique of electroelution of anionic polymeric resins is based on the removal of metal ions adsorbed to the resin, resulting from a potential difference applied between the cathode and anode in an electrolytic cell. The electrolytic cell was composed of an aqueous solution with suitable chemical characteristics and an anionic polymeric resin bed loaded with gold. The resin used in the experiments was loaded using synthetic alkaline gold cyanide solution with 1.0 g/L of gold. The variables studied were electroelution time, cathode current density, distance between cathode and anode and the electrolyte chemical composition. Statistical methods made it possible to establish the optimum conditions that would achieve satisfactory gold recoveries by the electroelution technique. The statistically predicted response for the resin loaded with gold by percolation was 16.5% gold recovery, 2.0 A/m2 cathode current density, 20-mm distance between electrodes and 6.0 hrs electroelution time. For the centrifuging system, the statistically predicted response was 7.41% gold recovery under the following conditions: 0.25 A/m2 cathode current density, 1-mm distance between electrodes, 3.5 hrs electroelution time and 10.9% NaOH in the electrolyte chemical composition.

Jan 1, 2002

It is recognised by the current JORC (1999) code that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological continuity and grade continuity. No prescribed criteria and rules will work for all situations or even between different ore types within the same deposit. Also these criteria and rules are sometimes applied without a clear understanding of their appropriateness, accuracy or correct implementation. For these reasons case studies are useful to evaluate and compare criteria commonly used to assist in resource classification. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody are used as the basis of a case study for the above-mentioned purposes. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce a random sample grid, a semi-random sample grid and a regular sample grid. Using nearest neighbour, inverse distance squared, ordinary kriging and sequential gaussian simulation, block iron grades are estimated using these three blasthole data subsets as inputs. This provides four groups of estimates with the ordinary kriging estimate based on the complete blasthole dataset being considered to represent the true estimate of iron grades. Also generated during this process are estimates of the error for each block. These error estimates range from the simple, such as drill spacing, through to more advanced methodologies such as kriging efficiency and simulation. These estimates of grade and grade estimation error are then compared to the true estimate using graphs and statistics. In order of increasing accuracy the block grade estimation and simulation methods were nearest neighbour, inverse distance weighting, ordinary kriging and finally conditional simulation. The simulation in some instances doubled the accuracy of individual block grade estimates when compared to nearest neighbour and inverse distance weighting estimates. It was found that many methodologies for estimating the error of individual blocks performed equally well with only methods such as average drill hole spacing and classification by search ellipse pass number performing poorly. An approach on how to convert the abovementioned error estimates of individual blocks into a meaningful JORC classification is also discussed. Although advanced non-linear resource estimates are applicable, most iron ore mines are still using relatively straightforward methods. The use of blasthole data and some simple linear interpolation methods and simple linear based error estimates makes this study repeatable for most iron ore sites and their resource geologists. This style of investigation is recommended as a useful approach for the Competent Person to apply to their deposit and thus better select, implement and understand the criteria used for resource classification and provide more consistency and confidence in the resource classification process.

Jan 1, 2002

By Alfred Osborne

Progressive cavity type pumps are widely used by commercial explosive manufacturers for pumping water gel, emulsion and emulsion / ANFO blend explosives. Tests by explosives companies and investigations into incidents have shown that this type of pump can develop dangerously high temperatures when operated deadheaded or dry. [i.e. with no flow of product through the pump.] In some tests and incidents, explosion or detonation of the explosive (or residual explosive) in the pump has resulted.

Jan 1, 2002

The discovery of magmatic nickel sulfide mineralisation within the Musgrave Block of Central Australia, in a region which has received virtually no exploration since the early 1970s, promoted a pegging rush throughout the region and provided a significant boost to the investor interest in resources sector companies. The discovery proved a significant success for the application of generic models for major magmatic nickel-copper sulfide deposits. The entry of junior explorers to the region is the principal mechanism by which the region will be explored, although significant social and physical challenges will impact on the ability of explorers to maintain investor confidence in the region.

Jan 1, 2002

New South Wales mining legislation reinforces a systematic approach to safety management. It is now a requirement of all mines in the coal, metalliferous and quarrying sectors in NSW to prepare a Mine Safety Management Plan. The paper briefly outlines work currently being undertaken by the Safety Operations Branch of the NSW Department of Mineral Resources (DMR). The DMR is working proactively with NSW mines in the preparation and implementation of effective Mine Safety Management Plans. There is a growing realisation that a systematic approach to safety management, underpinned by the process of hazard identification, has real potential to improve safety in the workplace. The paper briefly describes the framework used in a current æmines education programÆ and its æduty of careÆ foundation. Particular attention is paid to the role of mining operators in the implementation of Mine Safety Management Plans and their expected behaviour in demonstrating compliance. One challenge is convincing some mining operators that they must adopt new ways of working. Safety Operations officers are often reminded of the need to translate Mine Safety Management Plans into practical safety systems during audits and inspections of mines and through investigations into accidents and incidents. To have a real effect on the mineÆs safety performance, using these systems must be a normal way of going about a dayÆs work for all persons who work at the mine: not a safety manual collecting dust on the mine managerÆs bookshelf. Mine Safety Management Plans are important to mining operators. Not only will positive involvement in the development and use of safety systems ensure they meet their obligations under mining legislation, but it will also help prevent themselves or their workmates being injured or killed.

Jan 1, 2002

By I. Meliadis

This study presents the methodology and proposals for the restoration of an abandoned quarry in the Greek island of Milos. The local data (soil, vegetation etc.) of the island were collected, analysed and compiled into thematic maps using Geographical Information Systems. The restoration plan was based on the G.I.S. database and suggested the revegetation of the disturbed lands with herbaceous (grasses and legumes) or woody (shrubs and trees) plants. Plants should be indigenous or from other areas with the same vegetation type. Herbaceous plants establish and grow easily protecting the soil from surface erosion. The revegetation success depends on the seed quality, planting season and methods as well as local environmental conditions. Our proposals aim to restore the abandoned quarry with methods that follow the natural succession of vegetation, have minimal environmental impact, low cost and the expected result will be similar to the surrounding undisturbed land.

Jan 1, 2002

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002

By Karl Jr. Zipf

The famous Homestake gold mine in Lead, SD. closed recently alter 125 years of operation. However, the mine may receive a new lease on life as a National Underground Science Laboratory (NUSL) supported by the National Science Foundation (NSF) and dedicated to high-energy physics experiments involving neutrinos. These experiments require the construction of many large underground chambers tells of meters wide at depths of over 21 18 m. Construction of such large openings at such extreme depths has few precedents m civil-engineering-type construction. The Spokane Research Laboratory has a long history of ground control research at the Homestake Mine and has supported NSF and the physics community in their efforts to develop a NUSL at I Homestake or other suitable location. This paper will summarize underground science and describe proposed underground science laboratories ill the United States, in particular tile proposed NUSL at Homestake. Next, the paper describes an empirical design approach using the Q system of rock mass classification for these large Openings. .M initial site investigation that produced three good case histories is described. The actual support system used at the three sites agrees well with support recommendations from current support design charts, giving credibility to estimates of the classification parameters and Q. Feasibility of, and support requirements for, 25-, 50-, and 100-m spans arc estimated in the anticipated rock mass. This analysis indicates that 25- and 50-m spans are probably feasible, but a stable 100-nn span may be unachievable. The empirical predictions are then compared to detailed numerical analyses. The paper concludes with preliminary support recommendations and necessary site investigations needed to make a proposed NUSL a successful reality. These studies have been important input to NSF for their decisions on the technical feasibility of developing the proposed NUSL. If NUSL is developed, it could enable scientific experiments in areas beyond high-energy physics. 'the laboratory could also enable research in rock mechanics. ground water hydrology. mining engineering, nine safety and health, and ground control.

Jan 1, 2002

By J M. Galvin, B J. McKinnon

Lightning Ridge, Australia, is the largest opal producing area in the world. Most opal is mined from shallow underground mines by individuals or small partnerships with the industry having been protected from large-scale development to date. The safety performance of opal mining has lagged both general mining industry standards and community expectations. The application of geotechnical analysis to the opal fields has the potential to considerably reduce injuries and fatalities. With consideration of the local culture, preliminary geotechnical analysis has been applied to some current methods of work utilised at Lightning Ridge. Practical solutions have been advocated and are presented in this paper. Improvements to safety generated by these practical solutions indicate that further geotechnical research at Lightning Ridge is warranted and would be beneficial.

Jan 1, 2002

By C R. Sundberg

Despite nearly a half-century of continuous production, the low-grade iron ore (taconite) deposits of North America remain economically competitive sources of raw materials for the domestic steel industry. The continued viability of these mature integrated mining-concentrationagglomeration complexes requires highly efficient utilisation of assets, especially the mineral resource. At Cleveland-CliffsÆ five North American managed operations, enhanced ore characterisation techniques are playing a critical role in their continued success. Due to the low-grade nature and complex mineralogical composition of these deposits, ore characterisation cannot solely rely on assay grades. Historically, taconite ore characterisation has augmented assay grades with bench-scale concentration tests to quantify recoverable mineral. The economic necessity for improvements in mill efficiencies and final product quality has mandated significantly greater knowledge of ore-related impacts. Cliffs Technology Center has met this challenge by developing a variety of novel iron ore characterisation techniques. The applications developed include both in situ and laboratory procedures, plus unconventional data integration methods uniquely suited for these deposits. This paper details the evolution of these novel ore characterisation techniques and their application to each phase of the operation: mining-concentrating-and pelletising. The improved ore characterisation techniques have contributed to successes at individual Cleveland-Cliffs managed operations including mineral recoveries exceeding 95 per cent and productivity increases exceeding ten per cent while consistently achieving customer product quality objectives.

Jan 1, 2002

Fluid inclusions and sulfur isotopic compositions were studied in a possible extension of the Toyoha polymetallic vein deposit. The objective of this work was to gain a better understanding of the ore depositional conditions, sources of ore constituents, and distribution of mineralizing fluid in the region. Fluid inclusions in sphalerite and quartz show that most homogenization temperatures range between 190¦ and 290¦C. Most salinities range from 0.0 to 3.4 wt per cent NaCl equiv. Sulfur isotopic compositions of ore minerals (pyrite, sphalerite and galena), determined by a conventional technique, range between 1.3 and 7.7 per mil. The mineralizing fluids were characterized by relatively low and various temperatures and low to moderate salinities compared to those at the southeast region of the main ore bodies (Izumo and Shinano veins) where rare elements such as tin, tungsten and indium occurred. Obtained temperatures and salinities were attributed to the mixing of hydrothermal fluids with groundwater. Sulfur isotopic data suggest sulfide sulfur was of magmatic origin. Isotopic temperatures, estimated from the isotopic fractionation factor between sphalerite and coexisting galena, are between 195¦ and 322¦C. The temperatures are only consistent with fluid inclusion homogenization temperatures in sphalerite or coexisting quartz when sphalerite was a honey-yellow coarse crystal lacking conspicuous colored growth bands. This suggests the detailed classification of mineral pairs growth textures will be necessary for precise in situ measurements to obtain reasonable eothermometric results.

Jan 1, 2002

By G Swayn, J Harpley

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluoride along with traces of cyanide. The disposal of SPL has been primarily in landfill because of difficulties in the development of a successful techno-economic SPL treatment process. Increasing concern about SPL landfilling practices is resulting in regulations in some countries to ban this form of disposal. As a consequence stock piling of SPL is occurring in an increasing number of countries pending the development of a successful treatment process. In 1992 Portland Aluminium investigated a SPL treatment process based on pyrometallurgical technology and approached a company called Ausmelt in Dandenong, Victoria, Australia, to ascertain if their submerged lance technology furnace process would be suitable to treat SPL. This approach resulted in Portland Aluminium, Alcoa and Ausmelt personnel working together on trials during 1992 - 1994 in Ausmelt's demonstration furnace to produce a slag and off gases containing hydrogen and sodium fluoride. The trials also evaluated the effect of oxygen enrichment to increase the concentration of hydrogen fluoride and the ability to recycle sodium fluoride particulate produced as the furnace off gases cooled. Other separate developmental work by Portland Aluminium, using CSIRO, resulted in the production of aluminium fluoride from the offgases from the pyrometallurgical process. The results of these projects influenced Portland Aluminium and Alcoa to authorise up to $A26 400 000 in December 1995 to construct a Research and Development processing facility to treat SPL at Portland. The Portland Aluminium unique gas treatment process converts hydrogen fluoride in the furnace offgases to aluminium fluoride in a multistage fluidised bed reactor, designed by Portland Aluminium. The aluminium fluoride produced in the reactor has been trialed successfully in Alcoa's aluminium smelting process as a replacement for imported aluminium fluoride. The installation in mid-2001 of a slag granulation system has enabled the production of a granulated vitreous slag having leachability qualities that conform to Victorian EPA criteria for the unrestricted use of the granulated vitreous slag from 'The Alcoa Portland SPL Process'. The unrestricted use of the granulated slag successfully completes 'The Alcoa Portland SPL Process' which treats the hazardous waste material SPL and converts it into non hazardous useful products.

Jan 1, 2002

By David Cole, Paul Cooper, Dale Preece, Jerome Stofleth

The Explosive Destruction System (EDS) has been designed at Sandia National Laboratories for the disposal of chemical munitions (phosgene, mustard gas, sarin etc.), many dating back to World War I. EDS is a portable system that is trailer mounted and consists of a vessel into which a chemical munition can be loaded and opened for neutralization with linear and conical shaped charges. Gases are contained within the sealed chamber. The linear shaped charges split the munition in two and the conical shaped charge (CSC) is aimed at the explosive burster, in each munition, which is detonated by the resulting shaped charge jet, Toxic chemicals remaining in the vessel following detonation are neutralized and disposed of. This paper documents the development of a new CSC needed to reliably detonate explosive bursters in an expanding array of chemical munitions that are beyond what the EDS device was originally designed to eutralize. Design of this new CSC was controlled by the need to deliver energy above the detonation threshold into the explosive after penetrating the outer steel casing, fluid, the burster casing and finally the explosive. Design considerations were driven by jet conditions at the steel/explosive interface inside the burster. Parameters to consider in CSC design include: 1) diameter, 2) liner thickness, 3) liner position in body, 4) explosive weight, and 5) liner shape or interior (apex) angle. The effects of these parameters on final CSC performance are examined in detail. CSC’s that meet the design specifications have been manufactured and tested. The performance of these charges are compared with the original design requirements.

Jan 1, 2002

The overwhelming weight of scientific opinion indicates that human activity is having a discernible and negative influence on the earthÆs climate system. The Australian Government, together with about 100 other nations, has accepted the findings of the Intergovernmental Panel on Climate Change third assessment report, released in 2001. This report was prepared by several hundred eminent scientists from all over the world, from various scientific disciplines and with differing opinions on global warming. The IPCC third assessment report contains a series of relevant, significant conclusions; for example, it finds that there is an increasing body of observations that gives a collective picture of a warming world and other changes in the climate system. Global average surface temperature increased over the past 100 years by about 0.6¦C. This may not seem much, but in the 900 years beforehand, the EarthÆs temperature remained relatively stable. The 20th century was the warmest of the past 1000 years in the northern hemisphere (there is much better information available from the northern hemisphere than the southern hemisphere). The 1990s were the warmest decade of the millennium in the northern hemisphere and 1998 was the warmest year. Although many factors influenced the EarthÆs climate, scientists are confident that greenhouse gas increases were the main factor contributing to global warming in the last 50 years of the 20th century. Increases in carbon dioxide, methane, troposhperic (lower atmosphere) ozone, halocarbons and nitrous oxide have all contributed to global warming. Combating climate change cannot be done without the cooperation of industry and the community at large. It is important that Government and industry work together to achieve greenhouse gas abatement while ensuring continued economic growth. The cause of the problem û the generation of greenhouse gas emissions û lies at the heart of the structure and size of modern economic activity. Greenhouse gas emissions are embedded in our way of life from our energy consumption patterns to the basic production of food. Moreover, the costs of the impacts of climate change to the earth will be potentially revolutionary, not merely evolutionary. It is in this light, acknowledging both the seriousness and nature of the problem before us that I want to reflect on the key drivers in the international climate change negotiations. A consideration of the past, present and future from what I see as the mid-way point in the process. In 1997, Parties agreed to adopt the Kyoto Protocol, which sets out mandatory targets for greenhouse gas emissions for developed countries.

Jan 1, 2002

Thank you for the opportunity to speak at this important conference attended by aspiring mining professionals, some of whom will become the leaders of the mineral resources industry that forms the solid foundation of AustraliaÆs past and that will fuel the exciting growth of AustraliaÆs future.I want to briefly touch on the history of our business, then look at the opportunities that exist in the contract mining industry and finally comment on what the educators need to consider in their curriculum to meet the needs of our business. Byrnecut started out as an idea in early-1987 developed by a group of four mining people. At the time the industry was on the high end of a mining boom, the era of the Bonds, Connels, Skases and so on. Riding on this wave of euphoria we borrowed $600 000 from the National Australia Bank and, without having enough knowledge to lose sleep over the potential risks, started business in mid-1987. The euphoria quickly evaporated with the 1987 October stock market crash. The bank pulled our overdraft, equipment finance rates increased to over 20 per cent per annum and my house was mortgagedseveral times over. The business learning curve was extreme for a young mining engineer who had developed his trade in the relatively sheltered environment of a large public mining house, namely WMC. We were somewhat bitter that the banks had done a runner. We were a private company, backing the business with personal assets with our shoulders to the wheel, whilst the Bonds of the world had theirnoses in the trough ripping off mum and dad shareholders. All of this had a sobering effect, namely keep your feet on the ground, stick to the knitting, work hard and worship cash flow. Since that stressful but adrenaline pumping beginning the company now employs over 600 people and is now working for major mining houses at over a dozen locations in Australia, east Africa and WesternEurope and the National bank is again our banker. On this basis I consider myself qualified for the subject of this speech.

Jan 1, 2002