Search Documents

By Xin Li, Zurui Hu, Fuming Zhang

High blast temperature is one of the important technical characteristics of modern blast furnace (BF), which is also an important technical approach for the green development of ironmaking. Increase blast temperature can improve and promote the BF operation smooth and stable, reduce coke rate, fuel consumption and CO2 emission. Top combustion hot blast stove technology has been applied in Shougang Jingtang’s 5500 m3 BF for 8 years. Under the condition of burning single BF gas, high efficiency energy conversion and over 1250 °C high blast temperature have achieved. The combustion and heat transformation process were researched by numerical simulation technology to optimize the structure design. The high efficiency annular ceramic burner and checker brick were developed and applied, the flue gas waste heat was recovered and reused to preheat the combustion air and gas. Prominent achievement of high blast temperature under the condition single BF gas burning has been realized.

Mar 1, 2018

By A. Schönecker, P. Y. Pichon, B. Kraaijveld, Y. Meteleva-Fischer

"Ribbon-growth-on-substrate is a casting method, which offers a possibility to control heat flow, nucleation and subsequent crystal growth at the liquid-substrate interface. This technology allows for low-cost and high throughput shaping of silicon sheets with controlled crystal grain size and orientation for use in solar cells. In this work, sheets of silicon- metal silicide composite materials were produced and their microstructure was studied. It was shown that depending on the relevant phase diagram and casting conditions, a micro/nano-sized eutectic structure of the casted sheet can be formed. Such composite materials possess properties promising for various applications in energy generation, storage and conservation. The advantages, potential and challenges of the ribbon-growth-on-substrate technique for production of composite sheet materials as well as novel areas of application for such materials are discussed.IntroductionThe Ribbon Growth on Substrates (RGS) process is well known in the solar industry as a process to produce multicrystalline silicon wafers. An industrial size pilot production line for continuous casting of silicon wafer was developed by RGS Development B.V. in the Netherlands (Figure 1). A comprehensive review of this technology and properties of the produced silicon wafers were reported by Schönecker et al [1]. The principle of the RGS process is explained in Figure 2. The relatively cold substrate extracts the crystallization heat from the liquid silicon in the casting frame. This results in the growth of a silicon ribbon (Vc) in contact with the substrate. When the substrate (Vp) is transported from the casting zone into the cooling section, the crystal growth stops, the wafer can be removed and the substrate can be re-used. Last few years large work was done on the industrialization and market development of RGS wafers for the solar industry. Part of this work was discussed by Schönecker et al [2]. Although there is still a good perspective on the middle and long term solar market for the RGS wafers, the current market situation was found to be unfavorable for new entrants."

Jan 1, 2014

By Pengfu Tan

A thermo-chemical model of the copper P-S converter and a viscosity model for the converter slag have been developed to predict the behavior of magnetite in the converter slag, amounts of slag and matte, compositions of slag and matte, volume of the bath, bath temperature, slag blow endpoint determination, SEMTECH OPC signals, and the viscosity of converter slags. The predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by the industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on Fe3O4 content in converter slag, slag viscosity, liquidus temperature of converter slag and skimming operation has been modeled and discussed as well. Some applications of the industrial operations have been presented.

Jan 1, 2009

By Yijun Cao, Shengpeng Su, Guihong Han, Xiangyu Song, Yanfang Huang

Binder is indispensable in the production of iron ore pellets and the quality of pellets seems to be related to the interactions between binders and iron minerals. Humic acid is proved a suitable binder for iron ore pelletizing. In this paper, the interactions between humic acid and iron minerals were investigated by adsorption experiments and molecular dynamic simulations. Adsorption experi- mentalresultsshowthattheadsorptionofhumicacidonhematiteiseasierthanthat on magnetite, and the maximum adsorption capacities of humic acid on hematite and magnetite reach 17.1, 7.39 mg/g, respectively. The results of adsorption iso- therms indicate that the Langmuir model provides the best correlation of the experimental data, while the thermodynamics results demonstrate that the adsorp- tion process is a spontaneous exothermic process. Molecular dynamic simulations reveal that the interaction between hematite and humic acid is stronger than that between humic acid and magnetite. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients', lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By Jilai Xue, Jun Zhu, Yongqiang Liu

"Up-grading silicon feedstock by removing B and metal impurities can improve process efficiency and lower production cost in metallurgical processing for solar cells production. Hydrometallurgical study has been carried out in laboratory through alternative treatments of the metallurgical grade (MG) silicon (-200 mesh) by using hydrogen peroxide, hydrofluoric acid (4 mol/L) and NH4Cl-NH4 F (30:5) solution. The experiments were usually performed under mechanical agitation at 70 ? for 5 h. ICP-AES analysis showed that B content in MG silicon after the hydrometallurgical treatment has reduced by 92.4 %, and Fe, Al, and Ca contents by 98.8 %, 98.0 % and 81 %, respectively. Kinetics of these processes was also studied for better understanding of the effects of silicon powder size, acid concentration, leaching and oxidizing time on the processing chemistry.IntroductionAs one of the most clean and promising new energy, solar energy is used more and more in many countries all over the world, especially in United States, Japan and European Union. Most of industrialized states have made their national photovoltaic plans, which have stimulated further increase in use of solar energy. Photovoltaic Industry is at a high growth rate about 30 % [1-2]. For silicon solar cells to remain the mainstay for the photovoltaic industry it is necessary to develop a low-cost solar grade silicon feedstock [3]. At the same time, the availability of the currently M-G silicon from the semiconductor industries becomes limited [4]. With the advantages of low cost and low energy consumption, metallurgical routes to product solar–grade silicon get more attention [5]. These routes mainly include pickling, slagging, vacuum processing and directional solidification, etc [6]. Among them the most important processing step is the directional solidification, but it still can not satisfy the industrial demand for removing B. Removing B from Si remains as one of the most difficult and important processes in making M-G silicon [7]."

Jan 1, 2012

By M. Wallin

Millions of tons of sludge from different metallurgical processes are produced worldwide annually, and the environmental impact of landfilling these often hazardous sludges stresses the need to understand their role as valuable resources. The current work explores the potential of producing a saleable low-phosphorous ferromanganese alloy by utilizing sludge from the silicomanganese industry together with an iron source. The aim of the project is to explore the feasibility and practical challenges related to reduction and dissolution of manganese and silicon from the sludge to liquid metal and slag. Parameters such as ratio of input material as well as the effect of adding limestone and coke to the mixture were explored by thermodynamic calculations and adapted experimentally. Results show that a ferromanganese alloy, in fact, can be formed, while silicon and calcium forms a complex slag that captures a significant amount of impurities.

By Ming-Feng Ye, Jun Wang, Guang-liang Wu

In order to reduce the Al2O3 inclusions in 50Cr5MoV roller steel produced by EBT-LF-VD-VC process in a steelmaking plant, the LF refining slag was optimized and the influence of optimized slags with different w(CaO)/w(Al2O3) ratios on reducing inclusions were investigated in the laboratory. The results showed that, when w(CaO) = 50–55%, w(Al2O3) = 25–30% and w(CaO)/w(Al2O3) = 1.5–2.0, this optimized slag can not only reduce massive Al2O3 come from aluminium deoxidation, but also change the remain into plastic CaO-MgO-Al2O3 spherical compound inclusions with 1–5 lm diameter, the harm on the performance of the steel was minimized.

Mar 1, 2018

By S. N. Monteiro, N. A. Cerqueira, E. B. Zanelato, J. Alexandre, M. T. Marvila, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

Mortar is a widely used building material and has its application in buildings in extremely vulnerable environments and susceptible to degradation, such as facades. The objective of this work was to evaluate the loss of mechanical resistance to compression and flexure and the loss of mass of the mortars with effluent sludge from paper industry, when exposed to saline environments. The specimens were done with 0, 5, 10 and 15% of incorporation in lime paste and subjected to saline mist equipment that sprays salt solution in cycles simulating natural degradation conditions using literature data. It can be concluded that mortars with a15%incorporation obtained a significant loss of mass and a decrease in their mechanical resistance, which impairs their use in civil construction and influence in other properties of the material, with a level of incorporation of 10% the results within Brazilian standards.

Mar 1, 2018

By Bin Xu, Qian Li, Xiaoliang Liu, Yongbin Yang, Hongwei Li, Tao Jiang, Yan Zhang

The direct cyanide leaching rate of gold from a gold calcine was only 71.33%, due to 19.51% of gold being encapsulated in the iron oxides. To enhance the cyanide leaching of gold, the calcine was pretreated with acid or alkali washing. The mechanisms by which acid and alkali pretreatment improve gold leaching from calcine are investigated through chemical analysis, XRD, and SEM-EDS characterization.

Mar 1, 2017

By José R. Parga

In some parts of the Comarca Lagunera with population of about 2.5 million people, situated in the central part of northern México, chronic arsenic poisoning is endemic and severe adverse effects attributed to As exposure have been reported. Lifetime exposure to arsenic will develop classical symptoms of arsenic poisoning such as skin pigmentation changes, gastrointestinal disturbances and neurological changes. There are several methods available for removal of arsenic from well water in large conventional treatment plants, however a very promising electrochemical treatment technique that does not require the addition of chemicals or regeneration is Electrocoagulation (EC). The EC operating conditions are highly dependent on the chemistry of the aqueous medium, especially conductivity and pH. In this study, Powder X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Mössbauer Spectroscopy (TMS) were used to characterize the solid products formed at iron electrodes during the EC process. This study will provide an introduction to the fundamental concepts of the EC method. Finally the results of this study suggest that the presence of maghemite and magnetite particles can be used to remove arsenic (III) and arsenic (V). In the field pilot plant scale study more than 99% removal of As species from groundwater is achieved.

Jan 1, 2005

By Bin Xu, Qian Li, Xishan Li, Yongbin Yang, Hongwei Li, Tao Jiang, Yan Zhang

The cyanide leaching rate of gold from a multi-refractory gold concentrate (18.05 g/t Au) containing 1.62% As, 20.76% S, 6.95% C and 1.31% Sb was only 1.33%. The enhancement of gold leaching was studied mainly by the pretreatment of oxidative roasting and alkaline sulfide washing. Results showed that after the two-stage roasting (i.e., I stage of 500 °C, 1 h and II stage of 700 °C, 2 h) most of sulfur (93.84%) and carbon (98.27%) were removed, but the gold leaching rate of calcine just reached 71.33% because the residual arsenic (0.63%) and antimony (1.15%) were still high. After alkaline sulfide (i.e., NaOH and Na2S) washing, the residual arsenic and antimony was further decreased to 0.21 and 0.65%, respectively. The gold leaching rate of the treated calcine by cyanidation could increase to 93.52% substantially. Also, the optimized particle size, NaCN concentration and leaching time were −0.045 mm over 85%, 0.1% and 36 h, respectively.

Mar 1, 2017

By J. R. Odekirk

The nature of mineral distributions and locking characteristics in mill products are important factors in understanding mill performance. Such data are obtained by microscopic point counting methods. Reduction 'of point-count data from volume to weight percentages, and reduction of data for each size fraction back to a head sample requires lengthy hand calculations. The use of computer processing for such data reduction results in obtaining information on a realistic time basis. An example of computer processed point-count data is presented.

Jan 1, 1981

By Dachun Liu, Xuepeng Li

Smelting-acid leaching process is a way to treat high-content arsenic containing copper dust. However, smelting makes a low recovery of valuable metals and acid-leaching produces large amounts of arsenic-iron slag. Arsenic sulphuration volatilization at low temperature was studied, followed by pressure leaching to selectively recover Cu, Zn, and In from copper smelting dust while minimizing arsenic contamination.

Mar 1, 2017

By Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

Due to complicated structure and composition of high-phosphorus iron ore, pure substances were used to simulate the chemical composition of high-phosphorus iron ore to study the reaction of fluorapatite at different temperatures and effect of additives. The gasification process of P during carbothermic reduction process was investigated using a quadrupole mass spectrometer gas analysis. It is found fluorapatite was reduced to phosphorus which diffused into iron and gas phase. From the gas analysis, it was observed that PO and P gas species were vaporized around 800 °C. As the reduction temperature increased, the diffusion of phosphorus into iron was enhanced. The presence of Ca(OH)2 as additives not only promoted the reduction of iron oxide, but also decreased the degree of fluorapatite reaction to inhibit P into iron.

Mar 1, 2018

By B. J. Elliot

The Outokumpu Oy flash smelting furnace was designed for a capacity of 69,5 mtph of concentrate. The history of developments on the flash furnace, from the original operating capacity of 55 mtph to a proven capacity of 115 mtph of concentrate, is summarised. The new feature of operation at BCL Limited is ?the use of screened lump coal reduction in the settler region of the furnace. This paper considers the effects of settler bath reduction on the furnace smelting capacity, the condition of the furnace ?lining and bath, and ,the slag losses generated from the flash furnace and ultimately to discard. By using the settler bath reduction technique the capacity of the furnace for smelting new concentrate has been increased by 15% and hearth accretion has been eliminated by direct reduction with coal, which has also allowed the generation of a substantial protective lining on the furnace walls and roofs. As a result of improved slag losses from lump coal charging the metal recoveries on the flash furnace have increased from 70% to 87% for nickel, 68% to 82% for copper, and 28% to 45% for cobalt.

Jan 1, 1983

By Frederick W. DeVries

The author was invited by "60 Minutes Australia" to provide on-site technical background on cyanide, mining, and the environment, in their investigation of the January 30, 2000, spill at the Aurul gold-recovery site in Baia Mare, Romania. Some remarks on the incident ?and its implications surround a showing of the fourteen-minute telecast. The thrust of the TV reporter was that aspects of the dam implied the owners' use of standards Jess than would have been met for installations in technologically more advanced locations (like Australia). As a result, the public-relations impact is one of embarrassment for the world mining industry.

Jan 1, 1998

By T. K. Mukherjee, C. K. Gupta

"The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids, plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc .. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction playa pivotal role.This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge (2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, which influences the metal recovery process significantly, has drawn a special emphasis. In the case of refractory metals, basic extractants like Alarnine 336 has been pressed into service to produce kilogramme quantities of pure salts of molybdenum and vanadium. Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using a solvent system comosed of DEHPA and TOPO."

Jan 1, 1996

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A PFS(polymeric ferric sulfate) coagulation-photocatalytic oxidation technology was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on TOC removal rate were investigated, and the results were compared with those of the common photocatalytic oxidation technology under the operating parameters of the photocatalytic oxidation defined. Single factor experimental results showed that TOC removal rate could reach 81%, when optimal operating conditions were as follows: TiO2 loading: 4.0g/L, irradiation time: 4h, initial pH is 5.1and PFS dosage:700mg/L. PFS coagulation and photocatalytic oxidation have synergistic effect, which is meaningful for highly efficient treatment of coking wastewater

Jan 1, 2015