Search Documents

By K. Rajani Kanth

Environmental problem is the major concern for any industry and there is a great need to that along green lines. Sangam Dairy being one of the most famous and wide spread Dairies in India, produces wide spectrum of milk products. The BOD levels of effluent water of this industry with MIF treatment were found to be around 100 ppm. Lot of research has been expended in the past to bring down the BOD levels to bare minimum. The main objective of the present study is to minimize the BOD level to the required level stipulated by environmental standards by employing various seeding materials. For this purpose microbes like Bacillus Subtiles, Pseudomonas, Aspergillas, Staphylococcus, and Pencilium have been employed and BOD levels were analyzed. Various Reagents, solutions with different dilution levels have been successfully prepared. Initial and final Dissolved Oxygen levels were determined before and after incubation. From the DO data, BOD was evaluated for all samples and comparison analysis of various seeding material was carried to suggest the efficient seeding material for the ETP plant. In the process, solutions of different dilutions have been prepared using difficult reagents. These samples are treated with above mentioned microbes and BOD levels are estimated. It has been observed that staphylococcus and Pseudomonas proved to be the best seeding materials. When there microbes have employed BOD levels fall to less than 10 and 20 ppm respectively

Jan 1, 2006

By V. Tsukerman, Ivanovam L.

"The potential of hydrocarbon resources in the Arctic oil and gas provinces is enormous. Oil, gas and condensate constitute the basis of mineral resource base of the shelf zone of the Russian Arctic; summary volume of hydrocarbons exceeds 100 billion tons of conventional fuel. Only in the Shtockman gas condensate field in the Barents Sea explored balance reserves equal to 3.2 trillion m3 of gas. It is necessary to establish a special regime of nature management in the Arctic. Environmentally oriented economic activities should be more actively stimulated. The Energy Strategy plans that starting from 2010 in the Barents and Pechora Seas up to 10 million tons of oil and 50 billion m3 of gas will be extracted, reaching the level of 30 million tons of oil and 130 billion m3 of gas in 2020. This task cannot be solved without intensification of geological exploration on the continental shelf. IntroductionThe elaborated strategy of mining enterprises should correspond to the modern paradigm of mining industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the Arctic zone of Russia which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents"

Jan 1, 2008

By Mingzhou Li, Lin Wu, Changren Tong, Fengli Yang, Shaohua Yang

"According to characteristics of Tm, Yb and Lu enriched oxides composition and problems in its traditional extraction separation process, the computer simulation of a optimized fuzzy extraction separation process, in which three products with high purity(>99.99%) could be obtained at same time, was carried out. Distributing Curves of every element in both organic and aqueous phases were worked out. Distribution rules of rare earth elements in every stage of the optimized extraction process were studied. The computation results of economical and technical index showed the consumption of the acid and base chemical reagents in the optimized process would be saved more than 30%.IntroductionFor the solvent extraction separation process of rare earths, countercurrent extraction process was widespread in the industrial practice. Normally, rare earth ions were extracted by the saponificated extractant and transferred into the organic phase, where the acidic extractant was saponificated by the base firstly. Then, the loaded rare earth ions were stripped from the organic phase into the aqueous phase by the acid. Therefore, the acid and the base were the main consumptions in the process, and the equilibrium acid of the stripped rare earth solution was one of the main pollution resources. Meanwhile, for the heavy rare earths, such as Tm, Yb and Lu, stripping was more difficult, and the equilibrium acidity of the stripped rare earth solution was higher, so the acid consumption increased greatly."

Jan 1, 2012

By M. Radwan

This research reports on the synthesis of advanced silicon-based structural ceramics from mixtures composed of natural sand (Sinai white sand), reclaimed silicon and graphite by the nitriding combustion synthesis method. With pulverized sand (? 40 m), we found that the nitriding combustion can be realized at self-sustaining mode in the SiO2?Si?C system under 3 MPa nitrogen pressure. Depending on the composition of the starting mixtures, single-phase silicon oxynitride (Si2N2O) powder as well as new Si3N4?Si2N2O and Si2N2O?SiC composite powders with controllable chemical compositions were successfully developed. The measured thermograms of various combusted mixtures and the thermodynamic characteristics of possible exothermic reactions in this system were discussed to explain the nitriding combustion behaviour and mechanism. Near-full dense Si2N2O were fabricated from synthesized Si2N2O powder with 5 wt % oxide additive by the spark plasma sintering (SPS) method at 1600 °C. The dense Si2N2O samples had good mechanical properties (18.7 GPa Vickers hardness, 3.3 MPa m1/2 fracture toughness and 363 MPa strength) and excellent chemical and oxidation resistance. The synthesized composite powders were also densified to high densities (> 90 % of theoretical values) by SPS technique. The results obtained in this study can be seen as a new route to prepare important silicon-based structural ceramic powders with various compositions/properties from cheap starting materials which makes them potential for wide range of applications.

Jan 1, 2006

By Jimsher N. Aneli

There are many experimental works on the investigation of temperature effect on the conductivity of polymers filled by carbon materials. However frequently the establishment of current nature in the polymer heterogeneous systems becomes difficult. This fact is explained by complexity of calculation of different physical or chemical phenomena passing in materials at variation of the temperature. Among these phenomena it must be noted some morphological changes in the structure of polymers. These changes reflex on the structure of conductive system of composites. So, it has been shown, that the character of temperature dependence of thermal noises level and conductivity of some polymers filled by carbon black essentially depend on some relaxation transition in the polymeric matrix. In this paper the effect of difference transitions in polymer matrix of filled by carbon black some polymers and rubbers have been investigated in a wide temperature range. The importance of such investigation is due to possibility of application of resistive temperature sensors based on conductive polymeric composites (CPC) to measuring technology. The experiments have been carried out in the cavity with regulation of temperature in the range 110-650K. The resistance of samples was measured by four electrodes method. The samples were obtained by hot pressing of dry mixture of powdered components at chosen temperatures, pressures and cooling time in the case of plastics and by peroxide vulcanization of the elastomers in the case of the rubbers. The samples were produced on the basis of the following thermoplastics: low density polyethylene, polytetrafluoroethylene, polycarbonate and polydimethylmethylvinilsiloxane.

Jan 1, 2006

By Zheng Wei, Jian Cheni, Zhenliang Weng, Wei Liang, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"By testing the dielectric constant and the dielectric loss factor of concentrated Dahongshan, mill scale, anthracite and light-burned dolomite in different frequency and temperature, and by studying the temperature-rising characteristics of the materials in the microwave field of 2.45GHz in frequency, the research in the paper shows that to reach at 1250°C under the same condition -2KW the microwave power and 30g the mass --the time concentrated Dahongshan takes is 330s, whereas the millscale is 855s and the anthracite is 820s. About the last one, the higher the temperature is, the stronger the absorptivity is. After the temperature has rose to 400°C, the anthracite's absorptivity increases dramatically. The result of the research would serve as the foundation of the further study on making direct reduced iron by microwave heating.1. IntroductionUnder the microwave fields, materials' dissipation of dielectric bodies would generate thermal effect. Therefore, the dielectric constant and the dielectric loss factor are closely related to materials' ability of absorbing microwave energy-the larger the dielectric constant and the dielectric loss factor are, the stronger the material's ability of absorbing microwave energy is, and the better the thermal effect would be[1-2]. In order to research how to make reduced iron from iron ore fines by microwave heating deeply and systematically, the test of raw materials' dielectric constants and dielectric loss factors are of the essence. What's more, because a mineral' conductivity is influenced by its components and crystal structure[3], it is necessary to study different materials' different temperature-rising characteristics; hence such studies would provide theoretical foundation of further research."

Jan 1, 2012

By Majid Sarkari, Hossein Atashi, Farhad Fazlollahi

"The aim of this research work was to prepare the efficient catalyst to purify pollutant output gases such as SO2 , NO2 and CO. This catalyst, lanthanum cobaltat (LaCo03) was prepared by the proper method in the analysis laboratory of Tabriz Oil .The first materials were chosen through calcination operation and temperatures of operation related to the Tamman temperature, therefore the basis for the first material of catalyst was nitrate and aqueous and since we had no availability to lanthanum nitrate, lanthanum oxide was used to prepare the nitrate one. Before all else, the first materials of catalyst were mixed together with the equal mole proportions and then, at the lower and upper temperatures of Tanunan temperature, calcination operation was carried out. To determine the molecular structure, the XRD analysis was utilized and specified that prepared lanthanum cobaltat was sixth aqueous and had the crystal structure type Triclinic.IntroductionLaCo03 has presented a vast interest because of its special electrical, magnetic and catalytic properties [1-4]. The catalyst LaCo03 can be prepared by means of several methods such as spray drying, freeze drying and also co-precipitation [5-12]. Some methods including hydrothermal, sol gel and citrate [13] This material usually has been synthesized by ceramic method and certainly the high temperature for the calcination operation. [14]. Lanthanum catalysts have been researched because of having such an active state [15]. One of the unique properties of this catalyst is the simultaneous conversion of pollutant elements. Nowadays CO oxidation has important applications in environment protection, such as indoor air cleaning and automotive exhaust treatment. LaCoO3 is one of the most important catalysts for CO oxidation."

Jan 1, 2013

By Donghai Li, Cheng Pan, Xuyang Liu, Xuewei Lv, Chenguang Bai

"Fine chromite ore is the common raw material to produce ferrochrome alloy through the submerged electric furnace process. The electric resistivity of fine chromite ore plays an important role in the operation efficiency because it determines the current distribution. The effect of particle size and the contact area of the particles on electric resistivity for several of chromite were investigated at room temperature, and the relationship between the electric resistivity of mixed particles and the volume fraction of lump ore to fine ore was also studied. The results shown that the electric resistivity increases with the increase of particle size, and the electric resistivity of mixture decreases with the increase of volume ratio of fine ore.IntroductionChromium is one of the most important alloying elements in manufacturing of stainless steel that used at high temperature and corrosive environment applications [I, 2]. As the raw materials to be charged into the steel, ferrochromium alloys and charge chromium are produced directly by smelting of chromite ore with the reducing agent in submerged electric arc furnace (SAF). During the process, the oxides of chromium and iron were reduced by carbon and meanwhile the electrical energy were consumed [3,4]. The ideal industrial process is to achieve high recovery level of Cr and Fe with minimal power consumption. In SAF process, the electric resistivity of charge stock has significant effect on the current distribution, which determines the heat distribution, molten bath structure and chemical reactions in the furnace. High resistance of the charge is desired to reduce the current distribution through the charge stock, thus the electrodes may insert into the charge stock with proper depth to form a high temperature arc heat source, and proper smelting can be realized[5]."

Jan 1, 2012

By Ruth Marlene Campomanes Santana, Michel Tieccher, Marcondes Mafacioli Pacheco, Juliano Urach

"IntroductionThe gaseous emissions of fuel burning by mobile sources are responsible for incidence and increase of many lung and cardiovascular diseases (Braga et al., 2007). These implications can watch in morbity as much as mortality, even when the levels of pollution are considerate restrained or lower. (Leite et al., 2002).Sample of mobile sources exhausts contain not only particles directly shaped by burning, but also secondary particles that results of reaction between other compounds (Burtscher, 2004).One of the principal pollutants produced by combustion process with major toxicity and raiser of adverse effects to health is the particulate material. In its constitution there are fine and ultrafine particles that can to extend deep portion of breath system, break epithelial barrier and reach the interstitial of lungs and then, to unleash inflammatory process (Arbex, 2004).The Particulate Material is employed to define a mixture of solid particles and liquid drops suspense in atmosphere. Queiroz et al. (2007) declare that this material can be divided in two types separated by size interval that together, represent the major class of disperse particles: the fine particles type of 2,5 µm de (breath particulate) and the type of earthliness particles, major than 2,5 µm to 10 µm (inhale particle). The difference of size between the particles influences on the physics and chemistry properties. They affirm that exist correlation between size of particle and heavy metals; how many lower was the dimension of particulate materials, major is the concentration of heavy metals.The inhale particulate (MP10) that is object of present study can exhibit in your composition sulfates, nitrates, amoniacal, marine salt (NaCl), soil elements (Al, Ca, Fe, Si, Ti), metals (Cd, Cr, Cu, Ni, Pb, V, Zn) and water (Queiroz et al., 2007).Recent studies have exhibit strong relation between daily levels of particulate material inhale (MP10) with diameter until 10 µm and others pollutants and one infinity of effects to health that go since total mortality of population, sicken for specific causes until congenital bad formation or even difficult win weight by the fern during gestation (Gouveia et al., 2006)."

Jan 1, 2008

By Hai-Xing Fang, Chao Liu, Tao Zhang, Bing Xie, Hong-Yi Li, Cui Li

"Hongge Ore, a kind of vanadium-titanium magnetite ore containing high content of chromium, is valuable resource for extracting Fe, V and Cr in China. During present processing of the ore, vanadium and chromium were both concentrated in slag, leading to higher content of chromium in the vanadium slag than that of common one in Pan-Steel. Mineral phases and characteristics of spine! crystals, which influenced greatly subsequent roasting process, in the vanadium slag under different cooling conditions were investigated by using XRD and SEM/EDS. Results showed that vanadium slags containing various contents of chromium were composed of spine!, in which V and Cr were both concentrated, olivine and pyroxene. Growth rate of spine ls decreased sharply below 1350°C. The non-isothermal crystallization process could be described by modified Avrami equation and Ozawa equation. Avrami exponent and Ozawa index were calculated and growth mechanism of spine! crystals was discussed.IntroductionVanadium (V) as well as chromium (Cr) is important non-ferrous metal widely used in materials and chemical industries [1, 2]. Especially, both of them are important alloying elements for the production of high alloyed steels to achieve desired physical-chemical and mechanical properties. Vanadium-titanium magnetite ore in Panzhihua-Xichang area (China) is an important raw material for extracting vanadium. During the extracting process, vanadium is firstly reduced into hot metal and then concentrated in slag phase by blowing oxygen into the hot metal in converter [3]. This kind of slag containing 5~20 wt% V20 3 are usually roasted with sodium or calcium salts and then leached to obtain vanadium containing solution and final products. Current vanadium slag obtained from normal vanadium-titanium magnetite ore contains low content of Cr20 3 and chromium extraction is thus ignored. However, chromium content in the vanadium slag would be increased intensively when the Hongge Ore used, which is also important vanadium titanium magnetite in Panzhihua-Xichang area containing 0.2~0.8 wt% Cr203. Therefore, this kind of vanadium slag with high content of chromium would also be important sources for vanadium and chromium extraction. According to previous work [4], both vanadium and chromium could be extracted from vanadium slag with high content of chromium by salt roasting and leaching, which is illustrated in Fig.1."

Jan 1, 2013

By Min Zhu, Yu Ji, An-chao Ren

"After being welded in the weld plant, the 100-meter heavy rails with the specification of 60kg/m are found broken during the straightening process in four planes. Failure analysis is made using the optical microscope and SEM with the result showing that the broken rail contains the imperfection of protrusion which exists at the edge of rail foot, about 1 00mm away from the rail end. When the protrusion is peeled off by deseamer from rail surface, cold scratch is generated which causes the rail to be broken during the subsequent straightening process. By adjusting the roll diameter differences between top and bottom roll of universal finishing mill and the height of pass line, it is possible to maintain the rails flat when leaving the mill. This prevents the upsweep and downsweep phenomena and, thus, the imperfection of protrusion can be eliminated. IntroductionThe development of rail transit worldwide has entered into a new era since the 1960s. The hi-tech rail transit system has gradually gained recognition over the world. In particular, the emergence of new-type passenger trains represented by TGV of France, ICE of Germany and Shinkansen of Japan and heavy haul trains as well, has revealed the charming way and more prosperous future of the modern and hi-tech rail transit system to the people all over the world. It should be pointed out that rail transit system is still the most effective solution to traffic jams among urban cities and in the central cities during the 21 '1 century, especially high-speed railway and subway which take overwhelming advantages over air transport, marine transport and road transport in terms of high speed, high efficiency, safety, comfort, environment protection and high flow. With the trend of increasing speed and heavier load of trains, higher product quality of rails is demanded. The rails for passenger dedicated lines require high cleanness, high accuracy in size, high flatness, high surface quality and large size (100-meter fixed length). The rail quality has direct influence on the operating performance of rail and railway traffic safety. The 100-meter heavy rails with the specification of 60kg/m are broken subject to the straightening process in four planes after being welded in the weld plant. This paper analyzes the reason for rails being broken and provides the theoretical proof for determining the rolling process."

Jan 1, 2013

By A. V. Tarasov

In order to improve technical, economic and environmental performance of hydrometallurgical processing of intermediate products containing copper and nickel, the Gintsvetmet Institute and the IMET Institute of the Russian Academy of Sciences have conducted studies into the efficiency of the use of alternating current of industrial frequency on processes applied for hydrochemical leaching of various copper- and nickel-containing materials. It has been found that: 1.Imposition of alternating current over the process of leaching of softly reduced nickel oxide with recycled copper sulfate solutions resulted in an increase by 20 to 30% of the rate of the copper cementation process and reduced by 20% its activation energy. At the same time, the recoveries of nickel, cobalt and iron to the leach solution increased up to 82.2%, 78.5% and 57.1%, respectively, and that of copper to the cement precipitate up to 74%. Optimal process conditions have been identified with respect to the current density, electrode material, copper concentration in solutions and the process temperature. 2.In the process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides, the grain size, the phase form of sulfides, the solution composition (H2SO4, Cl?, Cu2+, Fe3+)and the current amperage had an effect on the nickel recovery to the solution, which reached 90%, while the degree of copper transfer to solution did not exceed 20%. The process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides with an addition of Cl? made it possible to selectively recover nickel into the leach solution along with concentrating copper in the leach residue. 3.When subjecting samples of commercial-grade magnetic fractions of converter matte to sulfuric acid leaching, the imposition of electric current, the concentrations of sulfuric acid and chloride ion in the solution and the duration of the reaction process had an effect on the process. The nickel recovery was 85% and that of cobalt and iron was 95% and the recoveries reached 97.5%, 98.3% and 99.8% as a result of repeated treatment of the primary residue under similar process conditions. Up to 75% of copper, 75% of sulfur and 99.0-99.5% of palladium was concentrated in the solid reach residues. The experimental data obtained indicates that the use of AC for hydroelectrochemical sulfuric acid leaching for separation of copper- and nickel-containing intermediate products has favorable prospects.

Jan 1, 2003

By Ryokichi Shimpo, Akio Fuwa

"The process-measurements of copper smelters in Japan were investigated for the summary of the latest technique and for the fundamental study of process control. The smelters investigated are those employing flash smelting furnace and P.S. converter, one reverberatory furnace and P.S. converter, and one continuous smelting converting furnace (M.I. process). Respective process is then considered, consisted of several reactors of different functions. The measurement methods were summarized in each reactor, including the measurement points. The methods of chemical analyses of the samples in each reactor were also investigated.IntroductionAn investigation on the process measurements, chemical analyses, and system control in copper smelters in Japan were carried out for understanding and summarizing the technique of the pyrometallurgical copper smelting operations. The typical seven processes in six copper smelters were investigated in the period from 1985 to 1987. The smelters investigated were Touyo Smelter of Sumitomo Metal Mining Co., Ltd., Kosaka Smelter of Dowa Mining Co., Ltd., Saganoseki Smelter of Nippon Mining Co., Ltd., Tamano Smelter of Hibi Kyodo Smelting Co., Ltd., Ashio Smelter of Furukawa Co., Ltd. and Naoshima Smelter of Mitsubishi Metal Co., Ltd. They include five flash smelting furnace and P.S. converter systems, one Mitsubishi continuous smelting and converting process (M.I. process), and one reverberatory furnace and P.S. converter system.The investigation was performed by making inquiries about the measurements, chemical analyses, system control, and their future prospects to the engineers in each smelter and by summarizing up in each item. The system control and future prospects were summarized in another paper titled ""Process Control Scheme of Copper Smelting Processes in Japan and Future View."

Jan 1, 1989

By Gary A. Wickham

In the zinc industry, this past decade has seen both prosperity and depression. Significant changes have occurred throughout the world in mining, smelting, refining, and marketing. This paper will review many of the industrywide changes of recent years and the potential impact for 1990s. In addition to an historical review of supply and demand are discussion of technology considerations for zinc and zinc based products, effects of geographical shifting of markets, and projections for the 1990s.

Jan 1, 1990

By C. E. Dodson

Conventionally hydrometallurgical recovery processes from sulphide concentrates include roasting, leaching, precipitation, impurity removal and zinc electrowinning. The use of the novel (yet commercially proven in other mineral and metallurgical industries) TORBED process reactor for the flash roasting of sulphides will be proposed. The potential advantages in its application will be discussed including very fine particle processing capability, lower cost smaller roasters, waste minimization, improved leaching efficiency and overall process simplification.

Jan 1, 1999

By Richard D. Hagni

The mineralogy of dusts from the lead sinter and lead blast furnace at the Doe Run Smelter at Herculaneum, Missouri is being studied by reflected light microscopy and scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS). Oust from the sinter plant consi5ts of abundant slag and galena particles, and lesser amounts of coke, sinter, and chalcopyrite particles. In contrast, dust from the blast furnace consist of abundant coke and sinter particles, and lesser amounts of slag, galena, chalcopyrite, metallic lead and lead-copper particles. The particles in dusts from remote sampling sites !-l mile from the sinter plant and blast furnace are fine-grained and composed principally of calcium-aluminum silicates that are locally derived, but some of the larger particles consist of sinter, slag, galena, and other minerals. Additional dust samples from the plant and remote sites are currently being studied.

Jan 1, 1991

By Sung Jin Han

Magnesia-based refractory is generally used in an electric arc furnace (EAF) due to its relatively high corrosion resistance and strength at high temperatures. However, the magnesia refractory is attacked by EAF slag and thus the lining life continuously decreases. Thus, it is significant to identify the interfacial reaction between magnesia refractory and FeO-rich EAF slags. In the present study, the influence of FeO-rich slag on the corrosion behavior of MgO refractory was evaluated. The (Fe,Mg)Oss layer was observed at the slag-refractory interface and its thickness increased with increasing content of FeO in the slag. The specific reaction phenomena and formation behavior of (Fe,Mg)Oss layer were evaluated by thermochemical computing program, FactsageTM7.0.

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By W. G. Davenport

The paper "Copper Smelting to the Year 2000" was presented at the CIM Conference of Metallurgists in Sudbury, August 1979. That paper predicted, in part, that high matte grade, high oxygen smelting - particularly in flash furnaces - would dominate copper smelting until the beginning of the next millennium. The present paper re-evaluates that prediction and examines the changes that have occurred and will occur in copper extraction in the 1990's. Of particular interest is the question as to whether major competitors are on the horizon for flash smelting and Peirce-Smith converting. Recent results with direct-to-blister smelting, lance smelting and submerged-tuyere smelting are reviewed and their roles in future copper smelting are predicted. Requirements for H2SO4 plants which handle the off-gases from modern smelting/converting processes are also examined.

Jan 1, 1993

By M. G. King

In 1982, Asarco operated six smelters and refineries producing primary copper, lead, zinc, silver and gold. At that time Asarco was still reliant on its custom smelting and refining roots and mined only 25% of its smelting and refining capacity for copper and 10% of its lead smelting and refining capacity. By 1992, Asarco had been reshaped to become largely an integrated primary metal producer operating four smelters and three refineries. Zinc is no longer refined and the mining capacity has been increased to meet 100% of copper smelting and 50% of lead smelting needs. Only one custom smelter is in operation. This paper describes the metallurgical changes and challenges which have occurred in this restructuring of Asarco's operations while maintaining Asarco's position as one of the largest non-ferrous metals producers in the world.

Jan 1, 1993