Search Documents

By Kenji Monden

"In order to obtain basic data for the development of highly thermally conductive composite materials, the thermal conductivity of a resin composite material with an Aluminum Nitride filler was assessed. Several different measurement techniques such as the xenon flash and the temperature wave thermometric analysis method were employed to gather data on these composites. An excellent match between theoretical and experimental data was achieved by employing a predictive expression that takes into account the effect of percolation on thermal conductivity.IntroductionA thermal solution composite is made by incorporating dense inorganic fillers with high thermal conductivity into a resin. Because the composite materials have high thermal conductivities, they have been used in electrical products that generate excessive thermal energy during operation, such as inverters, amplifiers and motor drivers. They function as electrically insulating and thermally conducting parts of the electric modules. As the uses of thermal solutions are expanded, composites of higher thermal conductivities will be required. The aim of this work was to investigate, evaluate, and try to predict the influence of key parameters on thermal conductivity and diffusivity. This was achieved by analyzing the effect of both volume fraction and shape of Aluminum Nitride ceramic fillers and measuring the thermal conductivity. In addition, the influence of percolation on thermal conductivity is considered. The thermal conductivity of the composites is discussed by employing a predictive equation using literature data of thermal conductivities for both the filler and resin. As well as thermal conductivity measurements the effect of volume fraction of the filler was also explored.ExperimentalSpecimen PreparationThe composite samples were prepared from silicone resin and Aluminum Nitride (AlN) fillers. The AlN fillers with an average particle size of 20 µm are shown in Figure 1. The mean diameters of the AlN particles used are given in Table I. For comparison the AlN fillers with an average particle size of 5 µm are shown in Figure 2. A planetary centrifugal mixer was used for simultaneously dispersing the components uniformly and de-aerating the mixture. After mixing, these materials were placed in a silicone rubber case and cured at 150 °C for 1 hour."

Jan 1, 2013

By G Hope, C Young, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing as it is refractory, increasing cyanide and oxygen consumption, and enviromnentally hazardous. Selective leaching and treatment of the arsenic would prove advantageous to conventional gold leaching methods. The reactivity of enargite samples from Montana, US and Quiruvilca, Peru were studied under alkaline conditions, pH range of 8-13, using a cyclic voltammetry corrosion cell setup. Raman spectra of the surface were taken during and after cycling to compare surface species against theoretical predominance diagrams. Under slightly oxidizing conditions, covellite (CuS) peaks were found on the surface in a short matter of time, above - 200m V vs SHE for pH 9-13, suggesting arsenic leaching, but for longer conditioning times, elemental sulfur peaks were also found, which created a passivating surface layer. By operating above pH 12, under reducing conditions, ~-500mV vs SHE, arsenic can be leached as a thioarsenate (AsS4-xOx3-), without sulfur formation.IntroductionEnviromnental limitations on pyrometallurgical processing of arsenic has pushed the desire to process enargite-, Cu3AsS4, bearing concentrates towards a hydrometallurgical solution. Attempts to process can be broken down into two categories - the co-dissolution of arsenic and copper under acidic conditions or the selective leaching of arsenic under basic conditions. The selective leaching of arsenic would preferably leave behind a chalcocite, Cu2S, or covellite, CuS, phase that would be more amenable to conventional processing methods of the copper and gold industries. These methods employ bi- or poly-sulfides to leach arsenic as Assl· [1-4], hypochlorite leaching [5-7], ammoniacal leaching [8] or fine grinding to mechanically activate the enargite surface and increase normally slow reaction kinetics[9]. This study looked into the surface formations of an enargite electrode under alkaline conditions, in a pH range from 8-13, as it cycled from -1000 mV to 1000 mV vs SHE. The understanding of the formations and under what conditions they form will be helpful in further development of any of the aforementioned processes."

Jan 1, 2012

By Jr. Brown, A. Calderara, A. L. Antozzi

"The result of extensive research into fundamental mixed metal oxide catalyst morphology has produced a next generation all titanium Dimensionally Stable Anode (DSA ®). This new DSA ® anode, patent pending, is tailored for electrowinning of non-ferrous metals (copper, nickel, cobalt, zinc) by means of this new coating technology.These DSA ® anodes are characterized by a hanger bar with vertical distributor bars, having primary titanium mesh attached by weldments. The active mesh is provided with noble-metal electrocatalytic coatings, consisting of iridium and/or ruthenium oxides, obtained by thermal decomposition of precursor solutions applied to the titanium substrates. The catalytic activity of state-of-the-art DSA ® anodes is increased by controlling the crystallite size of the noble-metals without decreasing the decomposition temperature. It is known that below a certain value (typically 400°C) the stability of these oxides, and associated lifetime, is seriously compromised. A highly active DSA ® anode, consisting of a quasi-amorphous phase, is obtained at high temperature (above 450°C), therefore not compromising lifetime performance. Through optimization of these design parameters, the manufacture of these novel anodes was identified.DSA ® anode performance advantages include: lead-free ' green' all titanium anodes, true leadfree cathode quality, energy savings of 0.3 to 0.55 V can be realized depending on the EW application when compared to industry standard lead-alloy anodes, eliminate need for cobalt sulphate addition required for lead anodes, sustainability designed into long-life recoatable anode structures, increase plant cathode output through increased current density operations, improve plant on-stream production, no sludge generated or removed, and improve current distribution producing smooth high efficiency cathode.Introduction of ProductThere are many factors to consider when engineering a high performance DSA ® electrowinning anode. Half of the anode's performance is derived from the physical attributes of the electrocatalyst and methods employed when applying this catalyst to the titanium anode structure. The other half of the performance benefits relate to the proper structural design of the anode. In this paper, we will highlight the anode development program in which De Nora has invested to provide the Electrowinning marketplace with a high performance anode product."

Jan 1, 2012

By Erich Hovestädt, Hans-Jürgen Odenthal, Christian Wuppermann, Herbert Pfeifer, Antje Rückert

"During the argon oxygen decarburization (AOD) process high-chromium steel melts are decarburized by oxygen and inert gas injection through sidewall nozzles and a top-lance. Due to the large amount of the injected processing gas, low frequency oscillations of the vessel can be observed. It is suspected that these oscillations can influence the converter's structure. The exchange of forces between fluid and the surrounding vessel is the focus of this study. An oscillation model was developed and tested, one objective being to limit the computational effort which is necessary for fully coupled and time resolved CFD and FEM simulations. Experimental results obtained from water-model studies as well as from on-sight measurements are available and were used in order to validate the numerical results. The authors' intention is a contribution towards a more in depth understanding of the factors influencing vessel vibration during the AOD process.IntroductionDuring the last four decades the AOD process has been established as a reliable and efficient refining process in stainless steel making. The injection of process gases (O2, N2, Ar) through sidewall nozzles shows advantages in mixing effectiveness compared to other injection geometries e.g. bottom blowing [1]. Stainless steel grades contain usually more than 10% chromium. With decreasing carbon content during the decarburization periods the tendency of chromium oxidation increases according to the varying chemical equilibrium which depends on the partial pressure of carbon-monoxide (CO) in the gas phase. That's why oxygen is gradually replaced by inert gases, usually argon or nitrogen, in order to lower the CO partial pressure and thus to minimize chromium oxidation. Despite the high injection velocity of approximately Ma = 1, the kinetic energy of the gas jets is consumed within a short distance from the nozzle exits due to the large density ratio between gas and melt of approximately 1:8000. With increasing distance to the nozzle exit, the initial horizontal velocity of the gas jet decreases and due to buoyancy force motion of the detached bubbles turns into a vertical direction. Subsequently a gas plume develops with its typical conical shape described by various authors [1-4]. Due to the drag force between gas bubbles and melt also the liquid phase is forced into a vertical motion. Near the free surface and the wall regions the melt flow is deflected in different directions. Subsequently, the typical flow pattern in the AOD vessel arises, as sketched in Figure 1 and described in literature [5-9]."

Jan 1, 2012

By Jeffrey Shepherd, Scott R. Smith, Eduard Guerra

"Electrochemical and spectroscopic evidence for the dissolution of a Au electrode by meso-2,3- dimercaptosuccinic acid (DMSA) from an acidic LiCl04 electrolyte is presented. Near the potential of zero charge, DMSA was determined to form a stable layer on the metal surface but at more anodic polarizations, DMSA was displaced from the metal through an oxidative process. The anodic displacement of the layer from the electrode resulted in a small amount of Au that was detected in the electrolyte using atomic absorption analysis. The extent of Au dissolution, was monitored while holding the potential of the electrode for 24 hours at the thermodynamic Eo/H,O in LiCl04 electrolytes containing 10 mM DMSA. This routine resulted in detectable quantities of a soluble Au-DMSA complex in the electrolyte and the greatest leaching was observed at a pH = 2.0. At room temperature, the leaching rate was stable at 10.9 µg cm·2 hr·' however, upon increasing the temperature to 50.0°C, the rate of Au dissolution increased yielding an average rate of extraction of 40.1 µg cm·2 hr- 1. Interestingly, after the first 12 hours of leaching at 50.0°C, the leaching current decreased dramatically suggesting surface passivation which prevented further Au extraction. The implications of this process in the industrial leaching of Au will be discussed.IntroductionThe use of cyanide in the industrial process of leaching Au from ores has raised concerns regarding both operational safety and environmental issues surrounding the disposal of spent leaching eftluents in tailings ponds. Depending on the chemical nature of the processed ore, the spent solutions that are released into the tailings ponds can contain toxic cyanide, either dissolved or complexed with different metals and may pose serious risk to wildlife as well as freshwater contamination to nearby water systems. Because of these issues, some recent studies have focused on the exploration of more environmentally-friendly molecules to selectively leach Au with appropriate kinetics. However, to effectively leach Au into an aqueous solution, a suitable ligand that reacts to form a stable chemical bond with Au is needed to form soluble Au complexes that can be later recovered [I]. Recently several sulfur bearing alternatives have been shown to leach significant quantities of Au in aqueous solutions. These include thiourea [2], thiocyanate [3], and thiosulphate [4]. However, alkylthiols are also known to quickly form a stable covalent Au-S bond [5], but have been relatively understudied in term of their ability to leach Au in solution, even though some short chain thiols are water soluble and relatively nontoxic."

Jan 1, 2012

By P. Mercille, M. F. Nasmyth, J. G. Cooper

The turn of the century sees considerable activity in the zinc industry for the replacement or expansion of existing cellhouses, and the building of new cellhouses as part of new zinc projects. Aside from the cellhouse technology itself, numerous engineering and construction issues play a major role in the success of a project for replacing or building new cellhouses. The purpose of this paper is to bring to light and to address the engineering and construction factors which go beyond the selection of a cellhouse technology and which remain of key importance in implementing such projects. In addition, some implications of these factors for project costs will be illustrated.

Jan 1, 2000

By Neil E. Izatt

The use of Molecular Recognition Technology (MRT), a selective separations technology using specifically designed ligands, has been established as an effective process for removal of metal ions found in many hydrometallurgical, chemical, and wastewater streams. The MRT process has been proven to be highly efficient and effective for indium extraction and recovery from zinc acid leach, electrolyte, chemical process and waste streams. A high percentage of the indium is recovered in a solid product format. MRT has also proven effective for germanium extraction and recovery from similar feed streams. This paper provides the indium and germanium metal recovery flow sheets and analytical results of the metal load and recovery steps.

Jan 1, 2006

By Andreas Stieben, Pierre Lutomski, Wolfgang Bleck, Martin Fischer

"For steel investigation and development, exact knowledge about the microstructural state is required. The information gained from 2D images often can't properly reflect the real 3D microstructural properties. In order to gain reliable information for meaningful models, simulations and correlations, it is necessary to accompany standard metallography with 3D information, which, unfortunately, is very difficult to access. This article presents a procedure for serial sectioning in combination with light optical microscopy. Only standard metallographic tools are employed in combination with image manipulation freeware. 3D microstructural data were extracted from three multiphase steel grades and in two cases virtual 3D-models of microstructural phases were generated.Three Dimensions Of MicrostructuresSince the invention of steel, craftsmen, inventers and engineers tried to improve its properties and tailor them to the requirements of new developments. For systematic development and enhancement of steels, the capability to investigate its inner structure is highly important, because it represents the linchpin between material production and properties. By having an in-depth understanding how production conditions form the microstructure and also how the microstructural state determines the material properties, steel design can be drastically improved. With this knowledge, microstructures can be designed to provide target material properties and process conditions can be identified that form these structures. Due to the key role of microstructure, the capability to gain accurate information about it is indispensable. It is the task of metallography to access and extract descriptive quantitative microstructural data like fractions, sizes, shapes and distributions of the different constituents. The most commonly used investigation tool in metallography is the light optical microscope (LOM). Besides this tool, additional high resolution techniques like Scanning Electron Microscopy (SEM) or Transmission Electron Microscopy (TEM) have become increasingly important. With these and other available methods, extensive information on the microstructural state of a material can be gained. Unfortunately, most metallographic methods have a major loss of information systematically built in. Analyses of microstructures are usually performed on surfaces, i.e. on 2D areas that emerge by cutting through the 3D material structure. This means, a complete dimension of information is not taken into account. How serious this reduction of information is and how it can affect interpretation of structures is exemplarily demonstrated in figure 1, which displays the planar structure emerging from a random cut through a simple 3D structure. It is very difficult to deduce or even imagine the original spatial structure from which this projection emerged and it is impossible to reconstruct it with absolute certainty without further information. The image has emerged from a random cut through a 3D structure of stacked cubes that is displayed in figure 2. The area shown in figure I is outlined. Although artificially constructed, this example demonstrates how distorted and misleading the view on structures can become by ignoring a spatial dimension."

Jan 1, 2012

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997

By Scott Shuey

The processing of post-consumer materials is an area being addressed by many industries and multiple engineering disciplines. While metal scrap and high-value uniform waste streams tend to find their way back to their respective parent processes, the more complex and low-cost ubiquitous materials, such as Polyvinalchloride (PVC) and Polytetrafluorethane (PTFE), tend to show up in many processing streams. From a metallurgical perspective, pyrometallurgical processing of a mixed metal/organic/oxide waste material allows for the recovery of thermal energy in conjunction with the recovery of metal values. The evolution of halogenic acids during elevated temperature processing can create complications with both the materials of construction of the processing equipment as well as gas stream processing. The need for dust collection coupled with a high acid content, necessitation high-volume scrubbing, increases the costs associated with gas handling. Control of the halides through entrapment as a solid in-situ during processing would simplify downstream processing. Alkali-halide complexes are being evaluated by researchers at CSM for mixed metal/polymer waste material treatment, recovering halogens as salt complexes.

Jan 1, 2006

By Robert T. Oxnard

"EXECUTIVE SUMMARYThe history of Refractory Recycling indicates there was little recycling until the 1950s. Energy incentives were the primary reason for the beginnings of a recycling effort by the refractory brick manufacturers. Quality benefits quickly became evident and fewer rejects were the result. Today, economic factors including higher valued raw materials and increased competition are the driving forces of refractory recycling.There are some success stories in refractory recycling but we have a long way to go. Few incentives, quality concerns, relatively cheap energy, comparatively lax government regulations, inexpensive landfills and inexpensive substitutes make recycling a difficult choice for many companies. Marketing advantages such as ISO 14000, eliminating multiple audits and reduced liability exposure can tip the scales toward recycling viability. Increasingly, the ideological philosophy of a company, a desire to minimize environmental impact and develop favorable public and other interested party perceptions can drive recycling and waste minimization efforts.Recycled materials can be more trouble ""up front"" and harder to ""manage"" due to their suspect quality. However, due to their nearly inexhaustible supply and the fact that once developed, they constantly contribute to the bottom line, they are certain to be the materials of the future. Waste refractory materials will likely see the same bright future as the steel scrap yards and slag piles of yesterday. In hindsight, we will realize that now was the perfect time to prepare and plan for the bright future of refractory recycling."

Jan 1, 2000

By Robert E. Brown

Magnesium recycling has been used to recover both new scrap and old scrap. It was used extensively in Germany during WWII to expand the magnesium supply. There were a large number of magnesium recyclers in the US who got their start smelting old scrap, old airplanes and old waste dumps from the WWII build up. As the world magnesium industry dwindled, only a few companies were left that did magnesium recycling as a primary business. The sand foundries tended to recycle of their production scrap in their melting furnaces. Even the original die casters tended to put scrap directly back into melting furnaces at the die casting machines. As high purity alloys were developed and the use of die castings in automotive work increased, the tendency was to let the magnesium recyclers convert the scrap back to high quality ingot. Automotive use has grown because of the low density of magnesium. This property is the one of the biggest problems to overcome in shipping scrap. Gates and runners from die casting are very irregular shapes and it is very hard to load a truck with enough material to get a low shipping cost per pound. Recent new equipment companies have developed magnesium equipment that is specifically designed to recycle, refine and cast secondary magnesium metal. These melt cells are supplied as integrated units to magnesium casting sites. The cost and effectiveness of this approach will be discussed.

Jan 1, 2000

By S. H. Amini

The effects of CaF2 and ilmenite on dissolution rate and diffusivity of CaO in calcium alumino-silicate based slag in a temperature range of 1500 ? 1600 ºC were studied by using the rotating disk/cylinder technique. The effect of rotation speed on the rate of dissolution in the base slag indicated that mass transfer in liquid slag played a significant role in controlling the dissolution. At a constant rotation speed, the effect of 5 wt% addition of fluxes tothe slag on the dissolution rate was investigated at various temperatures. While CaF2 had the highest effect, addition of ilmenite increased the rate of dissolution significantly. The diffusivity of lime in these slags was quantified using the dimensionless mass transfer correlations for rotating disk/cylinder in the melt. The diffusivity values were deduced using the data on dissolution rate and solubility of lime in the slags. The measured diffusivity in base slag at 1500 C was found to be about 1.32 10-5 cm2/s and increased to 3.07 10-5 cm2/s at 1600 °C. Addition of 5wt% CaF2 increased the diffusivity by a factor of 3 to 5, while 5wt% ilmenite increased the diffusivity by a factor of 2 to 3 in the temperature range of 1500 to 1600 ºC. The two examined fluxes reduced the activation energy of diffusion.

Jan 1, 2006

By K. Santowski, S. B. Breyner, T. Prietl

"The material properties of alumina products can be significantly improved by adding Cr203 containing raw materials. Cr203 and Alz03 form an alumina-chromia solid solution during firing, reducing the solution potential when in contact with acidic slags. During service, both a high chemical and high thermomechanical load are present for example in the tuyere zones and taphole areas of metallurgical vessels. For such applications conventional alumina-chromia products suffer from discontinuous spalling as a result of high and frequent thermal shock. Therefore, alumina-chromia materials were developed that exhibit improved thermal shock resistance, compared to the standard products, combined with sufficient corrosion resistance. Laboratory tests evaluated the physical properties of the newly developed alumina-chromia grades and a field test in a Peirce-Smith copper converter demonstrated that the material properties meet the corrosion and thermal shock resistance required for this application. IntroductionTo develop refractory products tailored to specific service conditions it is important to have a profound knowledge of the metallurgical processes and furnace conditions [l]. This enables the specific refractory consumption to be minimized and increases the overall operational efficiency. Economic considerations such as steadily increasing energy and resource costs have resulted in companies investing in recycling processes. In the base metal industry for example, recycling operations involve modifications to the smelter feed, process conditions and chemical composition of the process slags. This adversely affects the performance of standard linings and drives refractory producers to search for material innovations."

Jan 1, 2013

By Qian Fu

Although chlorine fluxing to remove magnesium has been widely practiced in the aluminum industry for many years, there appear to have been few fundamental studies of the kinetics and transport phenomena involved. The paper describes such a study in which the rates of reaction of individual argon/chlorine bubbles with aluminum/magnesium melts were measured. The detachment of bubbles from a submerged nozzle, at variable depth in the melt, was detected by a microphone and the arrival of the bubble at the top surface by conductivity probes. Analysis of exit gases and mass balances yielded the overall progress of reaction. Experimental results are interpreted in terms of heterogeneous reaction kinetics and mass transport to the bubble-melt interface,

Jan 1, 1996

By Robert F. Jenkins

This document addresses the use of practical and basic engineering principles to develop a computer model for the analysis of the various issues which affect heat transfer in aluminum sidewell furnaces. These issues include furnace charge conditions, furnace operating conditions, furnace general arrangement, furnace combustion conditions, and furnace ambient heat loss. The engineering principles applied to this model were first put to test over 20 years ago. A prototype computer model developed 12 years ago has been in continuous use by Thorpe Technologies to determine the performance of sidewell furnaces for the aluminum industry. A new computer model has enhanced capabilities for more detailed performance analysis including regenerative and oxygen enriched combustion.

Jan 1, 2000

By Z. R. Llanos, W. G. Deering

Gulf Chemical and Metallurgical Corporation (GCMC) has been operating facility for treatment of spent catalysts in Freeport, Texas since 1974. Recently, GCMC expanded its operations with the addition of an electric furnace for the production of fused alumina and mixed alloys. GCMC and its affiliate Sadaci, started up a new pre-treatment facility in Ghent, Belgium in 1998. GCMC is also part owner of Bear Metallurgical Corporation, a major producer of ferroalloys in the United States. This paper reviews the processes at these facilities. Changes in the management of hydrotreating and hydrorefining spent catalysts are discussed in light of recently issued federal regulations that made the majority of spent catalysts a listed hazardous waste.

Jan 1, 2000

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By R. Ghisleni, R. E. G. Bohrer, L. Radtke, R. M. C. Santana

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionThe first major global assessment of climate change science in six years has concluded that changes in the atmosphere, the oceans and glaciers and ice caps show unequivocally that the world is warming. The report released on February 2, 2007, the first of four volumes to be released this year by the IPCC, also confirms that the marked increase in atmospheric concentrations of greenhouse gases is the result of human activities.The transport sector has become by far major source of environmental pollution in urban areas. The continual traffic growth has raised concerns over the impact of traffic emissions on human health and urban environmental quality, and has fuelled the demand for a coherent regulatory framework for the management of traffic, air quality and emission at urban level, as well as at regional and national scales.In Greater Metropolitan São Paulo, Brazil, fossil fuel combustion in the transportation system is a major cause of outdoor air pollution (Miraglia&El Kouri, 2007). In China several studies on gaseous emissions are being conducted by F. Costabile&Alegrini, (2007), developed a study on the pollutants in the city of Beijing suggesting methods for the control of pollution.The results obtained from the estimation of the atmospheric pollutants emitted monthly in Campo Grande/MS, Brazil, by buses and minibuses, which employ diesel, biodiesel or natural gas as fuels showed that the substitution of diesel by biodiesel would diminish the emissions of pollutants (Kozerski&Hess, 2006)."

Jan 1, 2008

By Kalyani Das Sarkar

"Steel Authority of India Limited, a Public Sector Undertaking with a production capacity of 14 million tones of crude steel, is India's largest steel maker and ranks among the leading steel producers in the world. SAIL owns and operates eight manufacturing plant – five integrated steel plants at Bhilai, Durgapur, Rourkela, Bokaro and Burnpur producing carbon steel, and three speciality steel plants. All integrated steel plants have hospitals of 650 – 750 bed capacity with modern facilities to serve it's employees and adjoining localities in a clean and sustainable environment.According to the Bio-Medical Waste(Management and Handling) Rules, 1998 and as amended to date, all Bio-Medical waste which is generated during the diagnosis, treatment or immunization of human beings or in research activities pertaining thereto or in the production or testing of biologicals are to be categorized and taken to any facility wherein treatment, disposal of this waste or processes incidental to such treatment or disposal is carried out.The hospital management has created adequate treatment facility for Sharp and Infectious Waste, Pathological Waste and Anatomical Waste through Autoclave, Shredding Machine and developing deep burial pits. Some of these hospitals is ISO 9000-14000 certified. Use of above said treatment facilities in these hospitals are discussed in this paper.INTRODUCTIONBio-Medical waste means any waste, which is generated during diagnosis, treatment or immunization of human beings or animals or in research activities pertaining to these or in the production or testing of biologicals.Steel Authority of India Limited, a Public Sector Undertaking with a production capacity of 14 million tones of crude steel, is India's largest steel maker and ranks among the leading steel producers in the world. SAIL owns and operates eight manufacturing plant – five integrated steel plants at Bhilai, Durgapur, Rourkela, Bokaro and Burnpur producing carbon steel, and three speciality steel plants. All integrated steel plants have hospitals of 650 – 750 bed capacity with modern facilities to serve it's employees and adjoining localities in a clean and sustainable environment."

Jan 1, 2008