Search Documents

By Carl C. Nesbitt

A study was conducted to examine the treatment of metal-bearing effluents by precipitating the metals as sulfides and simultaneously collecting the particles by flotation. The precipitant was hydrogen sulfide gas which was introduced into a bench-scale column cell with air. The study included experiments of various flotation reagents and column configurations in treating solutions containing dissolved copper, lead, mercury, iron, zinc and cadmium. An acidic laboratory waste from a local copper operation was used to test the column with a solution containing several metals and arsenic. Precipitates were observed to form at the gas/liquid interface when the gas mixtures were rich in H2S. Copper, mercury, lead, and cadmium were precipitated from solution as sulfides to concentrations near detection limits. The flotation of these precipitates was enhanced with small amounts of S-7151 promoter from American Cyanamide Company and Dowfroth 1263 mixed with the feed. The recovery of the precipitates in this manner produced a smaller volume slurry which was easier to dewatering than a slurry produced by conventional precipitation techniques. The low pH and high oxidation-reduction potential in the cell from H2S addition was not conducive to form precipitates of iron, zinc or arsenic. However, these ions were precipitated as sulfides by raising the pH of the column discharge.

Jan 1, 1994

By Wayne Bell, Shivanand A. Borkar, Anish Upadhyaya, Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"A refractory ore body located in Michigan’s Upper Peninsula contains high concentrations of nickel and copper chiefly occurring in the minerals pyrrhotite, chalcopyrite, and pentlandite. Refractory ore bodies are difficult to treat by conventional mineral processing methods so microwave pre-treatment of the ore is employed to increase metallic-particle/host rock liberation by making use the differential thermal expansion properties of the mineral phases that absorb microwave energy. The Curie temperature measurement of metallic-bearing particles is in agreement with the known value for pyrrhotite occurring at 325°C. A nickel-rich iron sulfide mineral is found to be in occurrence and also appears to be magnetic under BSE imaging. It is shown the ore particles heat rapidly when exposed to microwave radiation for short durations of time mainly due to the high concentration of ferromagnetic mineral phases. Rapid heating causes thermal expansion of constituent mineral phases that produce cracks within ore particles. SEM imaging shows fracture occurring along grain boundaries and throughout host rock matrix. Ball milling experiments show an increased grindability of the ore resulting in a decrease in work index values.IntroductionCrushing and grinding operations consume 50-70% amount of energy used in mineral processing operations [1]. All these processes involve high energy impact of surfaces to develop compressive stresses that produce cracks to initiate breakage of particles. Microwave pre-treatment of certain types of ore might provide an energy savings to these type grinding processes by taking advantage of the tensional forces produced by selectively heating microwave absorbing type mineral phases. The heating of ore particles produces cracking by thermal expansion of the constituent mineral phases. Conventional heating has been investigated and shown to positively aid in grinding processes but determined energy inefficient to be used commercially."

Jan 1, 2011

By Volker Uhlenwinkel

The design of a free fall atomizer as well as the process parameters affect the particle mass flux distribution in the spray cone. The mass flux distribution is important in spray forming because of its influence on the deposit shape and enthalpy input into the deposit. In this article the effect of different process parameters on the mass flux distribution is shown. Furthermore, different melts were atomized with the same atomizer. An empirical correlation will be introduced to predict the mass flux in the spray cone. This correlation will be compared with experimental results.

Jan 1, 1999

By Petre Stelian Nita

In small steelmaking shops, in foundries and forging plants, there are not too many option to recycle the basic slags, which are not suitable for many purposes of recycling, because of their low chemical and structural stability. A solution of an adequate recycling is a direct recycling in EAF. Several quality requirements, physico-chemical properties and proportions of slags must be analysed. The progress in this fields permites to establish an adequate proportion of recycled slag, based on enough exact computation of the related property. For oxydizing slag, obtained during melting and in the first part of decarburization operation, the problem of phosphoms contents can be analysed using the phosphate capacity (C PO34-). For reducing periods, during deoxidization operation, desulphurization also occurs and the problem of the sulphur contents can be analysed using the sulphur and sulphide capacities ( Cs / Cs) Between this two complex thermodynamic indicators of the slags. a direct relation is established, using thermodynamic aspects, resulting from the equilibrium constants for dephosphorization and desulphurization process and also, using the optical basicity of slags, computable from the chemical analysis of the slags. On this basis starting from the steel quality requirements. adequate strategies can be established in order to obtain high rates of recycling (between 50-80%) of steelmaking slags. Important cost savings are obtained through this procedure, based on the correct amounts of the fresh lime, iron ore and fluidizers. Keywords: Slag, Properties, Recycling

Jan 1, 2003

By Jian-Xun Fu, Hong-Qiang Liu, Si-Yu Liu

The production of zinc-bearing solid dust is up to 4%~8% of total crude steel in steel plant, which is difficult to be recycled in traditional methods. To fully utilize the resources and reduce environmental pollutions, Chinese steel plants are using rotary hearth furnace (RHF) process to recycle solid dust. A consequential life-cycle inventory was carried out to assess the impact of dust recovery on greenhouse gas emissions based on the local production status. In the study system, the selected steel plant named which have 10.5 million tons of Crude steel productivity and 0.48 million tons solid dust come out meanwhile. To research, a RHF production line of 0.3 million tons directly reduced iron (DRI) a year was established to recycle the solid dust. The DRI will be obtained from RHF and sent to the blast furnace as raw materials to reduce the demand for iron ore and coke in steelmaking processes. By researching on the life-cycle inventory in the system, the steelmaking process with RHF was 2299.3kgCO2/ton steel. It’s a little higher while compared with the process without RHF, which data is 2297.0 kgCO2/ton steel. The small production of DRI make a small difference to reduce the carbon footprint of steelmaking process, the added carbon footprint of RHF process is more than BF and other steelmaking processes reduced. It is concluded that dust recovery has no contribution to the greenhouse gas emission reductions in the technic condition of Chinese steel plants currently.

Jan 1, 2016

By R. Dekkers

Non-metallic inclusions in liquid steel are mainly formed during killing. As far as these particles are not captured by the slag, they are found in the cast steel where they can deteriorate the mechanical properties. Inclusions may also disrupt the continuous casting process, affecting thus directly the quality of the steel and the production capacity. Steel pin samples from the Sidmar plant (Belgium) were taken in different steps of several ladle treatments and in the tundish. Also slab samples were studied. All samples concern the same type of low alloyed aluminium killed steel. The non-metallic inclusions were isolated from the steel matrix and investigated with scanning electron microscopy and energy dispersive spectrometry. The evolution of the non-metallic inclusions is described by their number, size, shape and elemental composition. The main non-metallic inclusions present are aluminium oxides and spinel type compounds.

Jan 1, 1999

By Manfred K. Walther

"Tests were conducted on instrumented plates cast in the Abex Experimental Foundry to compare recorded solidification histories with results computed for corresponding models simulated with the C.A.S.T. program. The first plate was cast of low alloy steel and the second of carbon steel with a graphite chill at one end. Both were cast in molds of bonded silica sand. Temperature histories were recorded in the castings, molds and chill. Exceptionally good agreement was achieved between computed and experimental data. Other investigators will find the results useful as a benchmark against which they can compare the results of their own calculations.IntroductionSince the early 1970's our foundry engineers have used both two- and three-dimensional versions of the G.A.S.T. program to gain knowledge of the solidification process [1,2,3]. Study of the computed data gave insight as to how the rigging and risering of specific castings might be changed or adjusted to improve quality and yield. New schemes based on such analyses were then recommended for implementation on the foundry floor. The degree of success of the new practice was subsequently evaluated after the part had been poured, shaken out and examined. Similar conditions were noted in the sectioned castings whenever porosity and voids had been predicted by the computations. Appropriate modifications, when found successful in the model, were applied to the process. This led to a reduction, if not complete elimination, of the defects. Such results gave credence to the use of these programs as an aid in the production of better castings.Earlier investigations on simple shapes revealed excellent correlation between output derived with the G.A.S.T. program and exact solutions. Results also compared favorably with data calculated using other codes as reported in the literature [4] and summarized in the Appendix. However, since the computer program had not been verified by direct experiment, it was decided to run instrumented tests to check the theoretical predictions with actual measurements."

Jan 1, 1986

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO = Zn(g) + CO2 This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction does not occur at an appreciable rate, as is expected from thennodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide coneentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By Mitsuhiro Ito

"To allow various wastes containing high levels of chlorine to be used as alternative raw materials for Portland cement, two practical methods of chlorine removal were developed. In the first method, chlorine is extracted from the wastes during the cement manufacturing process. In the second, ash-dust waste with high chlorine content is first washed and then dehydrated to cake before being introduced to the cement manufacturing process. This cake can be used as an alternative for some cement raw materials. By combining the two methods, various wastes previously considered unsuitable for recycling due to their chlorine content can often now be used in cement manufacturing plants. As such, these methods represent a major contribution to environmental protection as well as a solution to problems relating to the diffusion of heavy metals and dioxins from cement plants.1. IntroductionWaste generation levels have risen rapidly in recent years. in both the consumer and industrial sectors and today, the need for effective, efficient waste management is one of the most pressing and serious problem of today's society.The Japanese cement industry has reacted to the increase in waste generation by using certain materials as alternative raw inputs or fuels for cement production, in an effort to contribute to society and conserve energy resources.These wastes often contain non-negligible levels of chlorine and heavy metals, however, both of which are unsuitable for cement production. Depending on the element content, Heavy metals have a particularly negative effect -on cement quality; in addition, they can be released into the environment. Chlorine, on the other hand, is contained in large amounts in incinerated ash from household wastes as well as in certain plastics. Both substances are considered impediments in cement-production, not only because they reduce the quality of the cement produced but also because they impair operating safety on cement production lines.To address this problem, two practical technologies have been established for separation and recovery of chlorine components during cement pre-processing and production. This paper introduces the application of these technologies with a special focus on incinerated ash from urban wastes, a representative form of waste material having notably high concentrations of chlorine, heavy metals, and dioxins. We also outline the technologies enabling this material to be used as an alternative input to cement production."

Jan 1, 2000

By Chu Bo-Yi

"This paper contains a comparison of creep-feed and shallow-cut grinding on ceramics with both neat oil and water-based grinding fluids. When a water-based grinding fluid was used in creep-feed grinding on ceramics the vertical forces and specific energies increased markedly fast with result that the wheel surface was damaged seriously. Creep-feed grinding on ceramics with neat oil not only produced much lower grinding forces and specific energies but also resulted in the wheel remaining in good condition and minimizing damage to the ground surface. This finding may lead to a deeper understanding of the behaviors of grinding fluids in grinding processes both on ceramics and metal as well.1. IntroductionAs advanced ceramics are obtaining more and more applications in the technical area, some machining processes are needed after the sintering to reach the accuracy and finish required by components. Because of higher hardness and brittle behaviors of modem ceramic many researches have been done in order to improve grinding efficiency and surface quality.In the grinding metals the concept of creep-feed grinding has been developed in industry as a real alternative to the normal method of shallow-cut grinding. In addition to the general economic advantages, dimensional accuracy and surface integrity are invariable improved using the creep-feed grinding technique.In grinding ceramics former studies have done many works on both creep-feed and shallow-cut grinding on ceramics with water-based grinding fluids since the water-based were thought to be better coolants than neat oil in most tests of grinding metals[l]. It was suggested that the specific grinding energies of ceramics are markedly higher in creep-feed grinding. The grinding force increases vary rapidly with time in the creep-feed case. In other words, so-called speed stroke grinding with high workpiece speed is considered more suitable for improving the grinding efficiency [2][3]."

Jan 1, 1998

By Yuri Gelfgat

"This paper presents some results of the investigation of the steady magnetic field influence on hydrodynamics and heat/mass transfer in processes of semiconductor single crystal growth (Si, Ge, InSn). The investigation employed mathematical and physical simulation techniques of relevant processes and full-scale experiments on growth facilities. A number of additional MHD phenomena have been found generated in the melt due to the rearrangement of flow pattern, the formation of specific convective cells, and the origin of MHD boundary and shift layer.IntroductionMagnetohydrodynamic (MHD) means of creating forces by contact-free methods in liquid conducting media have been widely used in the production of volume semiconducting single crystals. The goal of this method is to control convective transfer processes in the melt volume and on the crystallization front [1-3]. This is due to the sufficiently high conductivity of semiconductor melts (s = 104 /106 O1m-1 ) and an obvious relationship between the hydrodynamics in the melt and at interfaces and the conditions of formation of single crystals and their quality [ 1].All types of MHD effects rest upon the generation of volume electromagnetic forces in the melt by various means as well as on the possibility to direct them arbitrary in space and to adjust easily their absolute values. Fig. l presents different means how to implement MHD phenomena during single crystal growth. It should be emphasized that in all the modifications given in Fig. l additional energy introduced into the melt cannot influence directly the crystallization process since it is incomparable to the energy of molecular forces. Both the influence and efficiency of MHD means are determined solely by the change of motion, heat and mass transfer characteristics."

Jan 1, 1998

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By S. Ferlay

"The main purpose of the ZIMA VAL project (Label EUREKA EU1367 and LIFE ENV/F/000278) is to demonstrate industrial scale recovery and recycling of the main components of used dry batteries (zinc, manganese dioxide, mercury, and stainless steel) into high added value products. The originality of the ZIMA VAL process resides in:1- the use of hydrometallurgy2- alkaline treatment implementation (highly selective) for zinc and mercury3- electrochemical recovery of high quality products.4- the recycling of all the battery components (zinc, mercury, manganese dioxide, stainless steel) ·5- low operating and investment costs.The process consists of physical classification, mechanical dismantling, hydrometallurgy and electrochemistry. The purpose of the demonstration plant in FALAISE (Calvados - France) is to define the technical and technological parameters of an industrial unit for the treatment of 2400 tonnes per year of used batteries."

Jan 1, 2000

By L. M. . Chia

The successful treatment of waste materials to recover metals with acceptable purity is often hampered by the presence of undesirable impurities. The problem is further complicated by the need to insure that any residues or solutions generated are environmentally acceptable. Hydrometallurgical processes involving leaching- solvent extraction-electrowinning offer some attractive features which address many of these problems. However, in certain instances trace impurities that contaminate the organics are difficult to chemically strip and interfere with the overall process efficiency. A new processing scheme has been developed which appears to provide some attractive alternatives for impurity removal from organics. It has been shown that many ionic impurities can be electrochemically removed from the organic by spontaneous direct reduction using solid metals. A variety of metal ion impurities have been removed from selected common organic extractants such as D2EHPA and TBP using different metals as the reducing agents. The results and probable mechanisms involved in the reactions are discussed.

Jan 1, 1994

By W. Mueller

The function of a process mineralogist in the operation of a copper mine and plant is to assist in the identification and classification of the operation's main throughput. These include ore, concentrates, slag and matte, and to a lesser extent, refined products. In addition, a number of other products not normally thought of in association with mineralogy are examined. These include scales from submersible pumps, failed boiler tubes, acid plant, and shaft furnace; characterization of inclusions in failed compressor gear teeth as well as in copper rod; and flue dusts from a smelter, air transported particulates and coatings on passive copper anodes in the refinery. Techniques and equipment required for these studies include simple hand magnets to the high intensity Isodynamic separator, visual examination to electron microscopes, x-ray equipment, DTA, IR, heavy liquid separation, and contracted services of custom laboratories. Several examined products from Magma Copper Company have been selected to illustrate the range of techniques and equipment required by a process mineralogist.

Jan 1, 1981

By Xi-Shan Li, Qian Li, Yong-bin Yang, Tao Jiang, Jie Ge

Compared with other pretreatments of sulfur & arsenic-bearing gold, double-layered pellet roasting has an advantage that sulfur dioxide and arsenic trioxide volatilizing from this refractory gold ores can be solidified into the coating without emission during the roasting. However, the separation of coating from roasted double-layered pellet should be focused on in the novel pretreatment. Based on the difference of physicochemical characteristics between roasted solidified coating and pellet core, several separation methods including grinding, drop impact and water quenching method had been systematically studied in this paper. The results showed that magnetic and gravity concentration could not obtain a satisfactory separation effect. The optimum separation rate of grinding was only 38.94% at grind time 12min, but it increased to 85.05% by drop impact under drop height 0.75m, drop times 20 and impact angle 45°, and that of water quenching taking advantage of slaking reaction of lime could approach 75.32%.

Jan 1, 2015

By K. Asokan, K. Subramanian

"Electrowinning of copper by monopolar cells require common anode and cathode busbar and crossbars to connect each electrode to the respective common busbar. On the other hand, the bipolar configuration warrants the end electrodes only to be connected to busbars; there is substantial reduction in copper requirement. In the present work, an electrowinning cell with bipolar electrodes and end electrodes, each having an area of 1000 cm2 was designed and operated. The bipolar electrode is made of mixed metal oxide coated titanium mesh welded to plain titanium sheet. Coated titanium mesh acts as anode and the plain titanium sheet acts as cathode. Environmentally unacceptable lead anode and the recurring loss of lead are done away with. Closer spacing of the electrodes, paves way for the application of higher current density leading to mass transfer enhancement. Performance of bipolar copper electrowinning cell is reported.1. IntroductionThe normally adopted practice in electrowinning of copper is the conventional monopolar configuration. In this practice, the individual electrodes act either as anode or cathode. Hence there is a need to connect every one of the electrodes to the common anode or cathode busbar and crossbars running across the top of the cell are necessary. The common busbar carries very high current which is divided among the individual crossbars and hence has to be thicker in relation to the current load of the cell. The drawback of the need to use common busbars of thicker cross section and the need to have crossbars are obviated in the bipolar configuration."

Jan 1, 2009

By S. Castro, P. Alfaro, C. Moctezuma

IMMSA operates a conventional roasting-leaching-purification-electrolysis plant for the production of zinc from concentrates in San Luis Potosi, Mexico. The leaching circuit was designed to take into consideration a feed mixture to the roaster with a maximum iron content of 7%. Since the start-up of the plant in 1982, the zinc recovery increased to 94.5%. However, an increase in the iron content in 1997 caused an important decrease in the global zinc recovery. Two new steps were added to the leaching circuit and modifications were made to the other steps in order to increase zinc extraction. Two new automated press filters were installed to replace the original vacuum drum filters and to minimize soluble zinc losses. Additionally, the residue treatment steps in purification were modified and a calcium removal circuit is just starting operation. These actions, besides improving the operations, have as the main objective to increase the global zinc recovery to levels above 94.5%.

Jan 1, 2000

By D. Tahija

The Getchell Mine produces gold from a geologically complex ore bearing high concentrations of arsenic and carbonate minerals. The mill treats the ore using high temperature aqueous oxidation in autoclaves, followed by conventional carbon-in-leach gold recovery. We laboratory tested a variety of Getchell ores to determine the effects on gold recovery of conventional factors such as grind size and retention time, as well as the influence of factors such as ore variability and preliminary carbonate destruction. Because the mill is currently operating, we were able to directly compare certain laboratory predictions with operational results.

Jan 1, 1999

By Jiechao Liu, Lijian Luo, Yubao Ma, Bo Zhang, Yanfeng Yang, Xin Hong, Luming Liu, Jienan Liu

Reduction kinetics of stainless steel slag in iron bath smelting reduction was studied at the temperature of 1500℃ ~ 1650℃. It was concluded that the reduction process consisted of two parts. That is to say smelting reduction was controlled by stainless steel slag melting initially and by interface reaction later. In order to increase smelting reaction rate, the melting point of slag should be decreased at the first stage and adjust the liquidity of slag at later stage. Smelting reaction rate will be accelerated by means of optimize the slag content. The optimal reduction result that all most all of the chromium in slag been recovered was obtained in temperature was 1500℃, basicity of slag was 1.0~1.2, the value of Al2O3+MgO was 25%.

Jan 1, 2015