Search Documents

By Tracie Zoeller, G. Paul Neitzel, Jr. Sanders

"As-cast aluminum alloy microstructures are highly segregated. Coring occurs when solute is rejected during solidification resulting in a non-uniform solute distribution across the dendrite arms. Furthermore, coarse constituent phases are formed in the interdendritic channels as a result of coring. These constituents are either soluble or insoluble and can form from the major solute elements, or the impurity elements iron and silicon. The dissolution of these constituents, or precipitates, is an important consideration in determining the microstructural evolution of an alloy. The properties of an alloy are significantly affected by the morphology of the precipitates. Precipitates can be either beneficial or detrimental to the properties of the alloy. Regardless of the nature of the precipitates present, it is useful to understand the dissolution process. A diffusion-limited dissolution model for planar precipitates is presented and compared to an analytical solution and to models in the literature. Experimental data for the dissolution of AhCu precipitates in a dilute alloy are compared to the proposed model, and found to have good agreement.IntroductionDuring the processing of precipitation hardening alloys, beginning with the solidification step and ending with the final solution heat treatment step, there are a variety of particles that form. Some of these particles must be dissolved and solute redistributed and re-precipitated in a more homogeneous distribution than as it first appears in the as-cast microstructure. The particles can be classified by size as microstructure develops during processing. Coarse particles that form during solidification can either be soluble, partially soluble or insoluble. These particles can be the result of coring of the major solute elements as well as the limited solubility of elements such as iron and silicon. Iron and silicon can combine with the major solute elements such as copper in 2xxx alloys forming coarse phases often referred to as constituents. Figure l(a) shows the as cast microstructure with the constituent phases, Al2Cu and the insoluble phases containing Al-Fe-Mn-Cu-Si [7]. During preheating the soluble phases such as AhCu that were formed by eutectic decomposition must be taken back into solution, whereas the insoluble phases remain essentially unchanged by most thermal operations. Figure l(b) and (c) show some of these constituents after subsequent preheating steps. In Figure l(b), AhCu platelets are shown and in Figure l(c) the remnants of the AhCu phase are noticeable, along with Mn-bearing dispersoid phases. Reduction in the volume fraction and size of these phases improves the ductility and fracture toughness as well as reducing the inhomogeneities that occur during coring. Also adjacent to the dendrite arm boundaries are smaller AhCu phases that precipitate by a solid-state transformation on cooling to room temperature."

Jan 1, 2004

By Micheal McCarter, Biswadeep Saha, Meenakshisundaram Ramanathan, Chai Ren, Sivaraman Guruswamy

"Three-point bend test was used to study the effect of electrochemically charged hydrogen and magnetic field on the embrittlement behavior of AISI 4340 steel in this work. Acoustic emission signals were collected during the test and analyzed to gain an understanding of the crack growth process. Cathodic hydrogen charging in AISI 4340 steel resulted in drastic reduction of ductility and strength. Hydrogen embrittlement was characterized by a change in fracture surface from dimpled ductile surface to quasi cleavage type fracture. No significant effect was observed in the presence of magnetic field. The acoustic emission signals collected during the test provided an indication of the extent of energy released during the crack growth process.*Support of this work by NSF through the award DMR-0854166 is gratefully acknowledgedIntroductionGrowing interest in hydrogen as a clean fuel and use of steel and other iron based alloys for storage and transport of hydrogen has led to extensive study of the influence of hydrogen on the mechanical properties of these alloys. Hydrogen interaction with materials may result in degradation of mechanical properties. Embrittlement, either ductile or brittle, can be described as a condition which decreases the toughness of the material or increases the ease of crack growth. Hydrogen present even in few parts per million is sufficient to embrittle steels at room temperature [1]. In most cases, hydrogen exposure is through an electrochemical process in aqueous corroding environments. In such cases, they are prone to be exposed simultaneously to electrically induced magnetic fields, which are also believed to affect the hydrogen embrittlement susceptibility of these alloys. So it is also important to study the effect of magnetic field on the hydrogen embrittlement susceptibility. Hydrogen solubility by electrochemical process in aqueous solution is proportional to square root of current density for iron. [2,3]"

Jan 1, 2012

By Nils Eivind Kamfjord, Mari K. Næss, Halvard Tveit, Edin H. Myrhaug

"As a part of the FUME research programme being done by the Norwegian Ferroalloy Research Association (FFF), the SINTEF Group and NTNU, several measurements towards quantifying the gaseous and solid emissions from the draining of the silicon furnaces for metal have been carried out.Based on the measured size distribution of the formed fume particles and known particle growth theory, an estimate of the growth time for the given particles has been calculated. The formation time for the measured NO amount has also been calculated based on the fume measurements and a thermodynamic model of the furnace gases combusting with air. The two “formation” times are in the same order of magnitude and they are therefore used as parameters in a CFD model, modelling that the formed fume particles are heating up the surrounding air and thereby forming NO according to the Zeldovich mechanism. The measurements show an approximately equal constant NO formation per fume particle. The CFD model shows results in the same order of magnitude, supporting that the particle growth and NO formation happen under near stoichiometric conditions and are controlled by the formation of SiO2 fume.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2) formed during combustion of fuels. The main sources for human made NOx emissions is on-/offshore transportation industry, power generations based on fossil fuels, agriculture and other industries [1]."

Jan 1, 2012

By Luis Hoyos-Reyes, Jesus Gonzalez-Trejo, Adriana Cervantes-Clemente, Marco Gutierrez-Villegas, Manuel Palomar-Pardave, Cesar Real-Ramirez

Recent improvements on Peirce-Smith Converters (PSC) have combined numerical and physical simulations. However, most of the physical simulations have been carried out in cold-water models with only one tuyere. Several authors have proved that 2D numerical simulations do not reproduce the hydrodynamic behavior observed in physical simulations. On the other hand, most of the 3D numerical models have used a PSC thin slice with only one tuyere, but symmetric boundary conditions on the virtual walls have been imposed in order to reproduce the behavior of the whole converter. Therefore, there is no coincidence with the rigid walls of the physical models. The aim of this work is to quantify the effect of the virtual walls boundary conditions of a PSC thin slice and to determine the minimum number of tuyeres to characterize the fluid flow behavior of the entire converter.

Jan 1, 2009

By Feng Liu, Bingji Yan, Zhiwen Shi, Hongwei Guo, Jianliang Zhang

During production of a large quantity of steel, slag is produced at the same time. This paper chooses blast furnace slag (BFS) as the main material for the research. The purpose of the research is to explore its optimal physicochemical properties and the use of BFS in building stone field. The paper elaborates the experimentation process of producing glass-ceramics and presents the results. The results show that SiO2 content in BFS and amount of Cr2O3 and Fe2O3 added as nucleating agents have certain effect on the properties of glass-ceramics. The results also show that the exothermic peak temperature of base glass is the lowest when adding 20% SiO2 to the BFS, and 2% Cr2O3 and 3% Fe2O3 as nucleating agents, which makes easy crystallization and optimal properties of the glass-ceramics.

Jan 1, 2015

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By C. R. Palmer

The Bureau of Mines investigated the use of ion-exchange technology for the recovery of precious metals from cyanide leach and spent electrolytic solutions. This research included adsorption of gold and silver on both weak-and strong-base anion-exchange resins. The effects of nickel, mercury. and iron on precious metal loading of strong-base resins were also determined. Due to the nonselectlvity of strong-base resins, selective elution also was investigated. Both commercially available and experimental weak-base anion-exchange resins were tested. None of the commercial weak-base resins tested were suitable for a caustic-cyanide system owing to their low recovery of precious metals at pH 10 or above; however, three experimental resins have possible application. Continuous tests conducted with mill cyanide solution in a multicompartmented ion-exchange column using strong-base anion-exchange resins adsorbed nearly 100 pct of the precious metals as well as the iron and nickel. During the elution of this loaded resin the iron was first removed with NaCI plus NaOH; then nickel with dilute H2S04 or HCl; finally gold and silver with thiourea in dilute HCl.

Jan 1, 1988

By H. H. Law

Large amounts of waste material in the form of flue dust are generated in the operation of copper smelter furnaces. As a result of increasingly stringent disposal, it has become important to develop methods for treating such metallurgical wastes to extract metals and convert them into salable products. A two-step closed-loop hydrometallurgical process, has been developed: (1) extraction with sulfuric acid removes about 90% of zinc and decreases the dust volume by 50%; (2) extraction with hydrochloric acid dissolves the lead and further decrease the dust volume by 75%. A process scheme for generating salable products is proposed.

Jan 1, 1992

By Christian Redl

"The Lattice Boltzmann Method (LBM) solves fluid dynamics problems based on a discrete mesoscopic approach. It is based on the Lattice Boltzmann equation which is a special discretisation of the continuous Boltzmann equation. Its principle advantage is that it can handle complex physical phenomena (like interaction between different components and surface effects), complicated boundary and initial conditions very well, free from many gridding and stability constraints that plague conventional numerical methods used for fluid flow simulations. Complex structures like porous media can be resolved directly. The LBM algorithm has a simple structure and acts locally, which is favourable for parallel computing. Its potential for metallurgical process simulation is demonstrated in the present study which is concerned with the simulation of the fluid flow in a copper winning electrolysis cell. The electrolyte is modelled as the carrier fluid and the oxygen is considered via a so called active scalar equation. The modelling of buoancy, momentum exchange and the free surface requires special effort. The results of the simulation are validated against experimental data obtained by Laser-Doppler-Anemometry. Despite the simplifications made, good agreement between the simulation and the experiments was found.IntroductionThe hydrodynamics in an electrometallurgical cell is a complex, highly non-linear phenomenon. It includes the simulation of a two component system with high density ratio, gravity driven flow and a free surface. A general solution to this problem is currently unknown.The flow field is a result of the combination of various hydrodynamic effects [18]. Metal deposition at the cathode yields in a decrease in the ion concentration, which reduces the density of the electrolyte. At the anode molecular oxygen is formed as a consequence of the oxidation of water molecules. The oxygen is solved in the electrolyte and again the electrolyte density is decreased. Both effects lead to a free upwards directed convective flow, refered to as natural convection."

Jan 1, 2001

By Kai Tang, Casper van der Eijk

Natural gas has been used as reductant in the production of iron for several decades. Recently, the use of natural gas as reductant for other metals has been drawing attention because of the low price of natural gas, as well as the reduction of CO2 emissions compared to the use of coke and coal. In this work, the reduction of a mixture of Ti- and Ni-oxides by natural gas has been studied. Within the Ni-Ti system, the intermetallic compound Ni3Ti is thermodynamically the most stable one. Therefore, powders of Ni-oxide and Ti-oxides were mixed in an atomic ratio of three to one and subsequently pelletized. Reduction was performed in a TGA furnace at constant temperature with varying reducing gas atmospheres. In a natural gas containing atmosphere, the Ni-oxide was easily reduced to metallic nickel while the Ti was reduced to Ti-oxycarbides or Ti-oxynitride when nitrogen was present. Depending on the process parameters, several percent of Ti was dissolved in the nickel-based solid phase.

Jan 1, 2014

By William J. Mallio

Substantial differences between in situ and conventional technology require that in situ ore grade be established for deposit as distinct from the total contained metal value. Establishing an in situ ore grade involves determining the fraction' of the contained metal that can be leached by the fluid. This depends on the proportion of the ore minerals that occur on fluid flow paths as defined by the permeability distribution. Mechanisms involved in the in situ mining of sulfides are: oxidation of the sulfur, solution of the metals, complexing of the released metals, and a transport to a recovery point. Metal ions may be delayed or lost due to inefficiencies in these pro-cess steps or by reactions of the metal ions in solution with the rock. These reactions can involve precipitation of new phases, exchange of the metals of the interest with Ca or Na in clays or zeolites, retention of metals in oxidized mineral grains, or secondary enrichment of other sulfides along the paths of the solution flow. The efficiency of solution of metals and potential loss or delay mechanisms are controlled by local equilibria (the Eh, pH conditions) present in different parts of the ore zone. Permeability distribution in the rock mass and the coincidence of ore minerais with flow channels must be determined before a deposit can be judged suitable for in situ mining. Laboratory studies indicate that the natural permeability system is dependent on the degree of cementation of veins by late generation hydrothermal activities. The major conclusions of the study are:, 1. Deposit selection is critical; suitable deposit types include deep lying sedimentary deposits, selected zones of porphyry systems and vein controlled hydrothermal deposits; 2. Adequate laboratory and geochemical analyses should be undertaken through quantitative petrographic study and permeability mapping; and 3. Economic incentives for in situ mining must consider limitations of recovery caused by inefficiencies in dissolution and transport associated with particular deposits.

Jan 1, 1981

By E. Açma

In this study, the production of Cu, Co, and magnetic iron oxide from the ancient copper, slags, located in Küre-Turkey, is investigated. In the process under development, fayalitic slags containing 1% Cu, 0.43% Co are reduced in a D.C. arc furnace with coke or graphite additions. A metallic alloy, consisting of 3.8% Cu, 3.3% Co, 2.1% S, and the rest being Ice, is produced by granulation of the liquid metal. About 85% recoveries of Cu and C:o are achieved by hot sulfuric acid leaching of these granules followed by H2S precipitation. The, production of magnetic iron oxide is possible from the discarded leach solution, loaded v:ith FeS04, by using a method with geothite precipitation, dehydration, controlled reduction, and re-oxidation steps. The magnetic oxides produced have 20 m2Jg surface area, 1:8.3 aspect ratio, and the coercivity of 330-380 Oersted.

Jan 1, 1993

By David Rees

Tomago Aluminium, a 400,OO tonnes per annum primary aluminium smelter in Australia, has installed Ozone for biological control of its process water. The system was designed in Australia by Ionics Watertec Engineering, whilst ANCO Australia monitors the water quality and provides technical support for the project. The motivation was initially to reduce operating costs, however investigations indicated that there were substantial environmental benefits to be achieved by the elimination of a part, or all of, the chemicals being used to control the system. Also the existing chemicals appeared to be losing their ability to control biological growth in the system, in particular, the legionella bacteria. Ozone water treatment commenced in January 1998 and after a short transition period has operated without chemical addition since. There appears to be no doubt that the biological control is effective, the clarity and purity of the water has improved and initial testing indicates that the corrosion control rate is acceptable, although some chemical corrosion control may be introduced after further testing around the total circuit to guarantee protection

Jan 1, 1999

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

"In order to make the stainless steel making process efficient and environment friendly, it is essential to minimize the loss of chromium to the slag phase. With a view to investigate the advantages of using CO2 to attain moderate oxygen partial pressures in the oxidant gas during the decarburizations of stainless steel, the present experiments were carried out to understand the oxidation kinetics of Fe-Cr alloys and Fe-V alloy with gas mixtures containing CO2. In the present work, the oxidation behavior of Fe-Cr and Fe-V was examined by thermogravimetric analysis (TGA). Various mixtures of O2 and CO2 were used as the oxidant gas and the oxidation rate was followed by the weight changes as a function of time.The experiments demonstrated that the oxidation rate is independent of temperature at present experimental situation, but has strongly related to the Cr-content of the alloy as well as the oxygen partial pressure in the oxidant gas mixture. The wetting of alumina by the iron drop and the change of the drop shape during the course of the oxidation were investigated by X-ray radiography."

Jan 1, 2010

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By L. Petitnicolas

The experimental study of nitrogen absorption and its removal from a liquid Ni-20%Cr alloy at 1873 K has been undertaken, using an experimental, apparatus based on the Sieverts technique in order to determine the solubility of nitrogen in the alloy. as well as the kinetics of nitrogen transfer across the gas/melt interface. Experiments show that nitrogen solute equilibrium content can be calculated using the Sievens law. Measurements point out the nitrogen absorption reaction rate to be well described by first order kinetics, whereas experiments on nitrogen removal reveal that the rate is better expressed using a second order equation.

Jan 1, 1996

By Sergey Komarov, Manuela Diaz, Sano. Masamichi

"Mixing time, bubble behavior and absorption rate of gas injected into a liquid bath through rotary L-shaped lances have been studied by cold models with an effort to improve refining characteristics of metallurgical processes. Two kinds of the rotary lances were tested, namely the single-hole lance and the multi-hole lance. The effects of gas flow rate, bath depth and rotation speed were examined.It is found that when gas is injected through the rotary lances, the mixing intensity and the gas absorption rate are larger than that for the gas injection through stationary lances. The effect of rotation speed decreases as the bath depth and the gas flow rate increase.The multi-hole lance produces much smaller bubbles, which lead to an increase in the volumetric mass transfer coefficient by 3-4 times as compared with the single-hole lance. However, the effect of rotation speed is smaller for the multi-hole lance. The obtained results are explained in terms of the bubble coalescence and fragmentation, the rate of which depends on the departure bubble size and the power supplied to the liquid bath.IntroductionIn recent years, there has been a growing interest in the development of gas injector for metallurgical processes. The majority of the previous work was focused on modification to the injector design to improve mixing and to increase the of chemical reaction rate. These two goals can not be necessarily achieved by the same way. Bottom nozzles and stationary immersed top lances, which have been widely applied to steelmaking processes, are effective for the bath mixing, but have a limit to decrease in the bubble size. This results from a vigorous coalescence occurring between the bubbles when they rise in the molten bath as a bubble swarm.One of the ways to ensure the small bubble size and the effective bath stirring is the gas purging through rotary injectors. A number of studies have been undertaken to improve the refining characteristics by using rotary injectors. All of them are related to aluminum refining. The SNIF equipment (The Spinning Nozzle Inert Flotation) has significantly improved the quality of aluminum products at National Luxemburg Aluminum [1]. Rotary injectors made in the form of a disc have been applied to the Alcoa 622 [2] and the GBF processes [3]. A study of the gas injection by a rotary impeller has been carried out by C. Leroy and G. Pignacelt [4]. All researchers note the significant improvement in removal of sodium, calcium, hydrogen and non-metallic inclusion."

Jan 1, 1996

By René Winand

The paper gives a synthesis of research work performed in the department during the last ten years and dealing with cobalt , copper and manganese electrodeposition in chloride aqueous solutions. Special emphasis is given to electrocrystallization. For copper, properties of the electrolyte such as solubility limits, electrical conductivity and complex ions stability are discussed in connection with leaching, purification of the electrolyte, and metal recovery. When possible, kinetic parameters and probable electrode mechanisms are given. Problems that are still to be solved are also listed.

Jan 1, 1985

By R. J. Dippenaar, W. H. Van Niekerk

"An injectable lime-based desulphurization reagent for the treatment of liquid iron was developed. Firstly, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na20 to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. Subsequently, pilot plant and full scale industrial injection trials were conducted. It was found that lime-based slags, containing Na20 and CaF2, are able to desulphurize liquid iron efficiently. By the injection of a lime based reagent consisting of 60% lime, 25% soda ash and 15% fluorspar at a rate of 7 kg reagent/ton hot metal, the sulphur level in the metal (115kg) was reduced from 0,07% to 0,01 % within 5 minutes. The lime-based reagent developed in this study was successfully injected, both from a metallurgical and from a pneumatic point of view, on an industrial scale. The mathematical model utilised in this study, can be used successfully to predict the course and extent of desulphurization by lime-based slags. IntroductionMainly due to environmental difficulties encountered with pure soda ash, dry slag formation with CaC2 and high cost when Mg are used as desulphurizers, much incentive exists for the development of an inexpensive, environmentally friendlier desulphurization reagent. As a first step in the development of such a reagent, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na2O to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. This was followed by pilot plant injection experiments in which the kinetics of the relevant desulphurization reactions were evaluated. Finally, full scale industrial trials were conducted. All three phases of the investigation will be discussed with the major emphasis being placed on the kinetic study."

Jan 1, 1996