Search Documents

By Hideaki Tokuyama

Recovery of Ni from acidic wastewater of metal surface treatment has been investigated for reuse of the metal and water. Ion exchange equilibria between Ni ion and a strong acid cation resin, DIAION SKIB, and effective diffusivity in resin particle have been studied and they related to the concentration of HCI. The amount of adsorbed Ni for unit quantity of resin decreases with the increase in HCI concentration. This trend is remarkable for acid concentration above 0.1 kmol/m3,. The exchanging ratio of Ni2+ to H+ in resin particle is I/2 and the values of equilibrium coefficient K and maximum exchange capacity Q are I.62 and 3.16 keq/m3 -dry resin, respectively. Effective diffusivity D. determined from the observed breakthrough curve increases with increasing concentration of DC!. A prototype of moving bed has been developed and applied for the recovery of Ni from model solutions of wastewater prepared by mixing HCl and NiCl2. This apparatus allows us to control the resin flow rate by changing the cross sectional area of hole I the Teflon plate installed at the bottom of resin bed. Characteristics of Ni recovery have been clarified under various liquid flow rates. In any case for Q1, Ni ion has been effectively recovered on SKIB resin and the removed fraction was more than 99.5 %. Higher loading ratio of ion is attained at larger liquid flow rate.

Jan 1, 2003

By D. A. Meyn, R. L. Holtz, C. S. Pande, M. A. Imam, D. J. Singh

"Various theoretical and experimental techniques used to search and develop new metal hydride systems suitable for hydrogen storage are described. The main theoretical technique under study makes the use of electronic structure of the candidate materials. Microstructural characterization techniques like transmission electron microscopy are being used to study the hydride formation. Novel processing techniques for material preparation such as those needed to produce thin films or amorphous phases are also being utilized. The techniques are illustrated with results from Pd, FeTi and Mg2Ni systems.IntroductionOf the four methods of hydrogen storage, compressed gas, cryogenic liquid, metal hydrides, and gas-solid adsorption, the metal hydride storage method is more attractive from the point of view of high volumetric density and safety. Compressed gas storage has disadvantages of extreme pressure, weight, and volume requirements, whereas storage of hydrogen as cryogenic liquid is unattractive due to the requirements of extremely low temperatures and high consumption of primary energy. Moreover, the number hydrogen atoms present in a volume of 10- 22 Cm3 (nH) in liquid hydrogen state (- 20K) is 4.2 whereas number of hydrogen atoms that can be accommodated in a free volume of 10-22 cm3 of various hydrides are as follows: LiH--5.9, TiH2--9.2, ZrH2--9.2, VH2--l0.2. High hydrogen concentration is usually associated with a large H/Metal atomic ratio but is also a function of structure."

Jan 1, 1994

By Dominic T. Jordan, Quinn G. Reynolds, Christopher J. Hockaday, Ian J. Barker

A direct-current (DC) plasma arc furnace is a type of electric furnace used for metallurgical operations. The successful operation of DC furnaces depends to a large extent on gaining a fundamental understanding of the arc phenomenon itself, and ensuring its presence in the furnace at all times. A method for detection of the presence of the arc in a DC circuit is presented, along with discussion of why this may be of value for certain modes of furnace operation such as brush-arc. The theoretical development of the method is presented along with supporting experimental work conducted on large-scale pilot-plant facilities.

Jan 1, 2014

By Alain Jardy, Thibaut Quatravaux, Denis Ablitzer

"A numerical model of the Vacuum Arc Remelting process has been developed and applied to simulate remelting of various metallic materials, such as specialty steels, titanium and zirconium alloys. In practice, electromagnetic stirring is sometimes used, resulting in a complex 3D molten metal flow. After having validated the numerical model for different remelting conditions, we can use it to study the effect of applying a constant or alternated magnetic field on the thermohydrodynamic behaviour of the melt pool. The intensity of flow turbulence, computed with a classical k-E model, is shown to depend strongly on the nature of electromagnetic stirring.IntroductionThe principle of the Vacuum Arc Remelting (VAR) process, illustrated in figure I, consists in melting a consumable metallic electrode of the required grade under a high vacuum, in order to obtain a sound ingot of good structural quality.During remelting, an electric arc is maintained between the tip of the electrode and the top of the secondary ingot, in order to ensure melting of the electrode. The metal droplets fall through the arc plasma and progressively buid up the ingot, which solidifies in contact with the walls of a water-cooled copper crucible. The secondary ingot formed in this way contains three distinct zones, corresponding to the liquid pool, fully solidified metal and intermediate mushy zone. In order to stabilize the arc, it can be confined with the aid of a magnetic field created by an external induction coil. This field can also be used to stir the liquid metal, the rotation induced being in the orthoradial direction. By reversing periodically the coil current, stirring can be alternated."

Jan 1, 2004

By Laihua Wang, Peter Hayes, Hae-Geon Lee

"This paper introduces a new process for the efficient removal of dissolved gases and inclusions from liquid metals. This process involves the creation and dispersion of fine bubbles in molten metals by introducing inert or reactive gas into a region of turbulent flow. The highly turbulent metal flow splits the gas into fine bubbles and results in good mixing between the gas and molten metal phases. These conditions are ideal for contacting inclusions in the metal with the bubbles and subsequent flotation of the inclusions to the metal-slag interface where the inclusions are then absorbed by the covering slag layer. Dissolved gases, such as [H], [0], [N] in the metals are also transferred to the gas bubbles and removed from solution.The process concept has been previously demonstrated using a full-scale air/water model to simulate the ladle-to-tundish system of continuous casting of steel. The present cold modelling work has further demonstrated the ability of the process to remove gas solutes. The results indicate that the efficiency of new process is several hundred times greater than that of conventional high speed rotating injectors which are currently applied in the treatment of liquid light metals.IntroductionDuring metal smelting, refining and alloying processes, unwanted gas and second phase liquid or solid impurities are incorporated into liquid metals. In the case of steelmaking, the gas-forming impurities include [0], [H] and [N], and the solid impurities as a result of deoxidation include Ah03, Si02 inclusions. Common impurities in liquid aluminium are dissolved hydrogen and solid Ah03. To avoid subsequent problems during processing and to improve the physical properties of the metal products it is necessary to significantly reduce the level of impurities."

Jan 1, 1996

By R. Ratnagiri, B. Minaie

"In order to expeditiously produce defect-free metallic components in materials processing applications, the relationship between the process parameters and the product properties needs to be well understood while minimizing the production engineering iterations. To achieve this goal, a realistic mathematical formulation of the process should be carried out and an appropriate numerical modeling of various phenomena occurring in such process should be implemented. The materials processing of transforming the molten material into a finished metallic component involves fluid flow and solidification/melting. In the present paper, a finite element based analysis of the fluid flow ·and solidification/melting phenomena in cavities is presented and the various issues in modeling these phenomena are discussed. These transport phenomena play an important role in determining the final characteristics and material properties of the part by affecting the formation of defects and microstructure. A realistic numerical modeling of these phenomena can significantly reduce the rejection rates during the process and can increase the quality of the final product.IntroductionDuring the intelligent materials processing of various metallic components, it is often required to have a thorough knowledge of the behavior of the transport phenomena involved in this process. This is due in large to the coupling that exists between the transport phenomena and the final material properties of the components produced during materials processing. This interrelationship demands that the pertinent transport phenomena in the form of fluid flow and solidification/melting be studied and predicted accurately. In many materials processing applications, the fluid flow is in the form of either a forced convection free surface flow intended to fill a cavity or a natural convection flow resulting from the gravity when the cavity is filled. In either case, the phase change in the form of solidification/melting is also involved in order to complete the process. However, the thermal history during this phase change has a direct impact on the material properties of the final part and the possible defect formation that may be involved. This thermal history itself is dependent on the nature of the fluid flow during the earlier stages of the process. As such, there is a coupling between the fluid flow, phase change, microstructure, and defect formation in the resulting component. It is therefore necessary to analyze these phenomena in order to find optimum methods to produce good quality parts by minimizing the defects that may be generated. Such an analysis can result in the development of appropriate numerical models for the process that can facilitate the economical and timely manufacturing of various components with high consistency. The present paper discusses the issues related to the transport phenomena encountered during materials processing of components engineered largely by using various combination of convective fluid flow and solidification/melting in cavities."

Jan 1, 1994

By E. N. Mounsey

Ausmelt Technology was selected by Bindura Nickel Corporation (BNC) as the basis for a new copper circuit to process nickel plant copper leach residue to blister, anode and finally cathode copper and recover PGM values at the Bindura Smelter Refinery (BSR). The process selected, based on Ausmelt Technology to smelt and convert the residue to matte and blister copper and produce a discard slag, is novel incorporating smelting, converting and slag reduction process steps in a single Ausmelt vessel. The process demands a high quality blister copper product with low levels of arsenic and nickel. This paper reviews the project and the initial operational results to the end of 1997 of the Ausmelt Top Submerged Lancing (TSL) smelter and discusses the implications for the wider TSL converter market.

Jan 1, 1998

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By Di Yang

The influence of high density (104 -105 A/cm2) electric current pulses (70 us duration) and continuous DC (~103 A/cm2) on the flow stress and ductility in tension of a high carbon steel wire were determined at 204°, 427° and 649°C. Electropulsing (100 pulses per second) with an effective current density of 100-200 A/cm2 gave a 10% enhancement in the uniform elongation of the wire at 204°C, but had no effect at 427°C and 649°C. In contrast, continuous DC either had no significant effect on the ductility or gave a decrease. The electropulsing per se decreased the flow stress only slightly at 204° and 427°C, but gave a significant decrease at 649°C. Continuous DC increased the flow stress at all three temperatures. The present results along with those by others suggest that the enhanced ductility by electropulsing and the reduction in flow stress may be further increased by raising the effective current density through increases in either the pulsing frequency, maximum current density of each pulse or pulse duration. This could conceivably increase the reduction per pass during wire drawing or the number of passes between anneals.

Jan 1, 2001

By Alexandre Monteiro

Alumina precursor powders can be precipitated from aqueous solutions, using hydrothermal decomposition of urea to deliver base homogeneously to the system. Primary particles agglomerate early in the process, generating a wide size distribution. The presence of a polymeric surfactant such as polyacrylate can suppress or delay agglomeration, reducing particle size and narrowing the size distribution. The stabilization of commercially available a-Alp03 powder with polyacrylate was studied, investigating the effects of polyacrylate molecular weight, ionic strength and temperature. The effect of aluminum concentration, polyacrylate molecular weight and urea concentration on the precipitation of alumina precursors in a sulfate- urea system in the presence of polyacrylate/polyacrylic acid was then studied. The hydrolysis kinetics were followed, and particle sizes were determined. Precipitates were further characterized using energy dispersive spectroscopy. The particle characteristics are discussed in terms of the process conditions.

Jan 1, 1994

By Stephen J. Hales

State-of-the-art Resistance Spot Welding (RSW) equipment has the potential to permit adaptive feedback through recent advances in computerized process control. The initial step toward achieving this goal involves assessment of the effect of specific variables and the interaction between these process inputs on spot weld characteristics. This investigation addresses this issue through the application of Taguchi methodology to understand and refine a RSW schedule developed for joining of two dissimilar aluminum-lithium (AI-Li) alloys of different nominal thickness. The experiment was designed to establish a hierarchy of inputs with respect to each 'other, and to determine the significance of these inputs with respect to experimental noise. Valuable insight was gained regarding the interaction between process variables and the effect of certain equipment-related changes. In spite of a decrease in equipment performance, an improvement in the maximum strength attainable for defect-free spot welds resulted from the application of the statistical experiment.

Jan 1, 1992

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By D. A. Salinas G., A. H. Castillejos E.

Pachuca tanks are commonly used in the hydrometallurgical industry to carry out leaching operations. The fluidynamic characteristics of the liquid phase, resulting from the injection of gas into the draft tube, are important to achieve the complete suspension of the mineral particles and has a decisive influence in the mass transfer processes occurring in this reactor. This study investigated the effect of different design and operating characteristics on the liquid velocity field. using a laboratory-scale Pachuca tank. The transparent model was filled with water, and air was injected through the bottom in the absence of mineral particles. The liquid velocities over the whole reactor were measured under several experimental conditions using particle image velocimetry (PIV). This technique allowed to obtain a very detailed picture of the liquid motion even in the draft tube, as long as bubbles were absent from the measured field of view. The experiments have shown that the liquid velocities increase with increasing the draft tube to tank diameters ratio, the distance from the conical bottom to the draft tube entrance, or the gas superficial velocity. On the other hand, an increase in the water level with respect to the draft tube outlet caused a decrease. A mathematical model, which used the no-slip model, to calculate the variation of axial effective density along the two-phase region, was found to predict liquid velocity fields which agree very satisfactory with the experimental results obtained under all the conditions studied.

Jan 1, 1999

By Jilai Xue, Jun Zhu, GermainKouma Ndong, Luxing Feng

High-temperature corrosion behaviors of Fe-Ni-Cr alloy as inert anodes for aluminum electrolysis have been studied. The effect of anodic overpotential on layer growth of anodic surface is specially considered. The corrosion layers on the anodes tested were analyzed using XRD and SEM-EDS to provide a fundamental understanding of the layers growth at metallic anode surface. The dissolution of the scale layers on the metal anode occurred with low overpotential, while AlxM3-xO4 spinel phase within the scale layers was found with an increased overpotential. A mixture of multiple MyO layers existed on the anode substrate. The results may be useful for understanding and controlling the corrosion behaviors of Fe-Ni-Cr anode for potential application in aluminum electrolysis.

Jan 1, 2015

By Sadi Medina

As it is characteristic from Custom Smelters, ENAMl Las Ventanas Smelter has to deal with different qualities and quantities of mining products from about 70 suppliers, that contain a variety of impurities that would be harmful for copper production. In order to increase the smelting capacity, an oxygen plant has been running since September of 1990. Moreover, to improve the environmental conditions, a new sulphuric acid plant started up to neutralize the metallurgycal off-gases from the Teniente Converter and partially from the Peirce-Smith converters. Based on the on-line operation among the reverberatory furnace and the Teniente Converter using oxygen enriched air to produce high grade matte, most of the volatilizing impurities, mainly arsenic, are collected as discarding compounds in the gas cleaning system of the acid plant. This paper describes the continuous performance of the Teniente Converter with acid plant, the results attained, the operation problems and how they were solved. The impurities distribution achieved in this process is also included.

Jan 1, 1993

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Jin Zuomei

The kinetics of dissolution of nickel matte in the presence of manganese dioxide with silver ions was investigated. The catalytic silver ions enchanced the leaching rate up to a factor of 17. The effects of stirring, temperature, particle size, concentrations of Mn02, silver and ferric ions, and the experimental procedures were studied. Solid residues at various levels of nickel extraction were examined by SEM, TEM, electron micoprobe and X-ray diffraction. These results indicated that the dissolution reaction was topochemical and fits a surface reaction control model. The activation energy was calculated to be 39.15 KJ/mol. The leaching rate of Ni3S2 was independent with stirring rate, but the reaction rate constant was inversely proportional to the initial particle diameter. The order of the reaction rate are 0.41, 0.69, 0.33 with respect to Ag+, Mn4+ and Fe'+ con-centration respectively. Thus a kinetic rate equation was developed. Moreover, we propose a mechanism of silver catalyzed leaching of Ni3S2'

Jan 1, 1990

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By O. Chemezov, Yu Zaikov, A. Apisarov, A. Isakov

"Silicon deposits containing 99,9 wt.% of main component were obtained by SiO2 electrolysis from chloride-fluoride melts. The operating temperature was varied from 973 up to 1073 K. The conditions for obtaining crystalline fibrous micro- or nanodeposits were determined. The deposits were investigated by ESM methodIntroductionThere are large reserves of natural quartz of high purity in Russia. Processing of this raw material by electrolysis in molten salts produces silicon containing 99.9 weight percent of basic substance.[1]This method is less energy-consuming in comparison to existing methods for producing high purity silicon from gas phase.Another advantage of the electrolytic method for producing silicon from its oxide in molten salts is the possibility of production of high-purity silicon under air atmosphere. It dramatically reduces costs of the electrolytic cell construction, and the operating costs at electrolysis.On our opinion, the main advantage of the electrolytic production from SiO2 in molten salts is a unique opportunity to obtain micro-and nanostructures of silicon deposits. In particular, it is possible to obtain fibrous structures of silicon. The electrolytic method allows smoothly adjusting the thickness and length of silicon micro- and nano-wires by varying the cathode current density and temperature of the process."

Jan 1, 2012