Search Documents

By Graeme Miller

The geotechnical characteristics of the ore are important in understanding the kinetics of a copper heap leach. These characteristics can indicate potential problems and can be used to determine the semi-quantitative changes in field kinetics as compared with column kinetics. The application of this approach allows a more rigorously based determination of ?scale up factors? than has been the case the date. The shrinking core model has been shown to be a poor predictor of leach kinetics based on the crushed ore size distribution. However the model itself is a very useful tool to analyse commercial heap data. Significant geotechnical parameters such as: bulk density / stress characteristic, limit moisture capacity and particle density are used to determine the effect of changes on the diffusion controlled leach rate. By consideration of the geotechnical reaction of the ore mass the leach rate changes are related to changes in these variables. Analysis of commercial heap data has indicated effective diffusion lengths of up to ten times the largest particle size.

Jan 1, 2003

By J. Murphy

The economics of microbial coal desulfurization are affected significantly by the proper selection of the plant site and by maintenance of variables at suitable levels. High sulfur coal particles below 200 mesh show sulfate production rates triple those with 150 mesh coal but grinding costs are greater. Slurry solids density increases from 5% to 20% reduced the rate constant by a factor of 10. Coal added to a batch reactor in the stationary phase resulted in a sudden second exponential sulfate production phase indicating feasibility of lower cost continuous operation. Successful operation in the absence of beef broth, yeast or added nutrients at non-sterile conditions enhanced projected economics. Finally, the need for adequate agitation and aeration was well established.

Jan 1, 1985

By E. Burgos Cruz

The behaviour of S, N and P during refining of Fe-18 wt%Cr-10 wt%Ni with calcium carbide was investigated. The effects of the initial contents of C and N in the metal phase, as well as the supply method of calcium carbide to the melt on the removal degrees of S and P were evaluated. Heats were carried out at 1873K, in MgO crucibles, using a laboratory induction furnace. It was observed that simultaneously with S and P, N and O have also participated in the reactions. It seems that, in fact, O governs the behaviour of the other elements dissolved in the melt and that N is had to the removal of P with calcium carbide. It was also noticed that high C content in the metal phase have not altered the dephosphorization and desuffirization degrees, but that the supply of calcium carbide done by injection led to a lower dephosphorization degree than the one obtained by dumping it.

Jan 1, 1995

By David K. Melgaard

Electroslag Remelting (ESR) is a complex process used to produce high quality specialty alloy materials. The quality can be directly correlated to variances in melt rate and immersion depth. Conventional ESR furnaces control these quantities using two independent control loops using proportional changes in current for melt rate and driving the electrode up and down to match a voltage set point for immersion depth. However it is well known that the control loops are highly coupled, i.e. changing the current to account for melt rate deviations changes the voltage depth relationship and vice verse. In addition the noise in measurements of the ESR process can be considerable, forcing conventional controllers to use highly damped responses. A new model-based controller has been developed to embody the coupling and improve responsiveness by using estimates from a reduced-order linear ESR model and the typical process measurements to control melt rate and immersion depth simultaneously. Kalman filtering is used to optimally combine the model estimates of eight process states and the measurements of voltage, current, position and mass to estimate the instantaneous melt rate and immersion depth. Several ESR melts under steady state and transient conditions were conducted to evaluate the performance of the new controller. This paper will discuss the design of the new ESR model and controller and will present experimental results demonstrating its much improved control and responsiveness. While this controller was developed for the ESR process, the effectiveness of model-based control in managing such a complex process with relatively simple equations suggests the approach could be employed for many other processes as well.

Jan 1, 2006

By O. Tiitu

Drying is a unit process that has numerous applications in metallurgical process industry. Kumera Technology Center is a worldwide equipment and process supplier, who has expertise on both direct and indirect drying. In a conventional direct heated dryer, the required energy is obtained from combustion of fossil fuels emitting a considerable amount of off-gases. However, thermal energy can be already available in some metallurgical plants such as modem copper smelters where steam is produced by waste heat boilers of flash smelting furnaces. The total volume of off-gases, and especially the amount of harmful gases, released into atmosphere can be remarkably reduced when using steam as an indirect energy source for drying. Kumera Technology Center has developed a new type of steam dryer for drying of, for example, abrasive copper concentrate with silica sand. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the existing steam dryers and the rotating drum dryers. In the design, special attention has been paid to overcoming the reported problems of excessive wear and clogging of steam tubes and to reducing the required maintenance operations. The Kumera Steam Dryer, having a patented flexible steam tube arrangement inside the rotating shell, has a high effective heating area - drum volume ratio without leading to problems with build-up and clogging. It can also be easily scaled up so that a single dryer can dry all of the feed for a large flash furnace. In this paper, we will present the operational and maintenance experiences from two years operation of the first full-scale Kumera Steam Dryer at Norddeutsche Affinerie Aktiengesellschaft in Hamburg, Germany. We will also provide an overview of the future developments with respect to construction and scale up as a response to market demands.

Jan 1, 2002

By J. H. Lee

LG Metals Corporation started its second smelter operation at Onsan along with the existing flash smelter on January 31, 1998. Onsan smelter has been producing about 140,000 tons of copper annually from concentrates with the flash smelting line since 1979. In accordance with an increase in domestic copper demand, LG Metals Corporation decided to expand smelting and refining capacity by introducing a second smelter line using the Mitsubishi continuous process and a new tankhouse in 1995. After two years' expansion works consisting of engineering, procurement, construction and a successful commissioning test, the total smelting capacity of Onsan smelter increased to 340,000 ton of copper annually from concentrates. This paper describes the smelting facilities, operation result, problems encountered and improvements during the start-up and early operation of Onsan's new smelter

Jan 1, 1999

By Barry T. Kilbourn

There is a continuous quest for better-performing materials, for example, to withstand higher temperatures, to resist more efficiently degradation or to be electrically conductive under extreme conditions. The oxides, and similar compounds, of the lanthanides and yttrium can, in some cases, help provide such behavior. Other advanced materials, such as hydrocarbon catalysts, optical ceramics or sensitive phosphors, may also require these oxides for some essential function. The role of the oxides in a wide variety of technologies, some novel and developing, will be reviewed and the underlying physico-chemical principles, the common threads, between several less well-known and apparently unrelated uses discussed.

Jan 1, 1989

By Esperidiana A. B. Moura, Mariana N. Sartori, Vijaya K. Rangari, Angel Visentim Ortiz, Francisco R. V. Diaz, Rene R. Oliveira

"This work presents the preparation and characterization of a nanocomposite based on Poly(butylene terephthalate) PBT and Brazilian smectitic clay (bentonite chocolate clay). Before being incorporated as clay nanoparticles in PBT resin, the clay was organically modified by the addition of a quaternary salt and sodium carbonate. PBT/Clay nanocomposite (96.3:3.70 wt %) was obtained by using a twin-screw extruder machine. After extrusion process, the nanocomposite was characterized by tensile, flexural and impact tests, SEM, Vicat, HDT, DSC, TGA and XRD tests. The results showed that the properties of the nanocomposite obtained were superior to those of neat PBT. Concerning the temperature of thermal distortion (HDT) an expressive gain of around 45 % was presented to PBT/Clay nanocomposite compared to PBT evidencing the interaction of nanofiller with the polymeric matrix.IntroductionPolymer-clay nanocomposites, also called as polymer layered silicates nanocomposites have attracted much attention from both industry and academia over the past decade because they frequently exhibit unexpected properties. In contrast to the traditional fillers, nanofillers, in particular, nanoclay, is found to be effective. The addition of a small amount (< 5 wt.%) can show significant improvement in mechanical, thermal and barrier properties, flammability resistance, and electrical/electronic properties of the final polymer nanocomposite without requiring special processing techniques. Also, as with other nano-size particles, the overall crystallization rate and the glass transition temperature are also affected. It is generally believed that the improvement of properties of nanoclay composites is directly related to the complete exfoliation of silicate layers in the polymer matrix. However, a processing technique that produces complete exfoliation is still a technical challenge [1,2]."

Jan 1, 2012

By Vittorio Basilico, Marco Quattrone, Mario Bassan

"In Italian building market one of the reasons that often stop building contractors from not taking into consideration the possibility to recycle rubble from building is represented by the increase of costs for rubble separation. However the recycling of C&DW can also allow a decrease in disposal costs and a reduction in raw materials requirement.In this paper the results of a testing conducted on a case study through economic and technical analyses are presented.Results highlight that a wise management of demolition and disposal processes can generate a remarkable saving and that it is possible, on the other side, to achieve environmental benefits such as reduction of raw material consumption and dump life lengthening.IntroductionTwo major factors have been found to have considerably influenced the market of recycled aggregates in Europe and Italy: the EU and national regulations and environmental awareness. The market of recycled aggregate has grown in countries with limited natural resources.Waste disposal has also been one of the top EU political and environmental priorities. In the complex interaction between human activities and the environment, waste is proved to be one of the most environment-degrading products.In 1972 the European Commission introduced measures on waste reduction, reuse and recycling. In 2006, directive 2006/12/EC (European Commission) on waste was issued. It covers the scope of minimizing the waste, prevent hazardous waste, maximize reclamation, reuse, recycling and energy-recovery.No specific directive refers to management and recycling of construction and demolition wastes. However, in 1992 the European Commission listed debris among waste management priorities because of its growing amount.Only recently, effective environmental policies have been implemented in Italy, even though relevant environmental issues started rising as early as the beginning of the 1970s. In the 1980s the Government undertook the first significant measures to handle the waste management."

Jan 1, 2008

By I. A. Ibrahim

Ilmenite, in its natural form, is an inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite. so that it can be leached with dilute hydrochloric acid, can be enhanced by chemical reduction in solution using a suitable metal as a reducing agent. The present paper aims at the evaluation of an Egyptian ilmenite ore for the production of synthetic rutile by direct leaching with hydrochloric acid in presence of iron powder. In this process, the titanium and iron contents are dissolved; meanwhile, the dissolved titanium is hydrolyzed and re-precipitated leaving mainly iron in solution. Leaching conditions were optimized to obtain less iron in the final solid product. Addition of sufficient amount of iron powder during leaching reduces the dissolved Fe3+ to Fe2+ and reduces the dissolved Ti4+ to Ti3+. The creation of Ti3+ in solution is assumed to have a role in dissolving the ferric iron and hence increasing the reactivity of the ilmenite ore. Synthetic rutile of about 90% TiO2 and 0.77% Fe2O3 was obtained from ore with a grain size 100% passing 200 mesh and a 5-hour leach time with 20% HCl at boiling temperature (110°C) and 0.11 g iron powder / g ore.

Jan 1, 2003

By F. Mucciardi

With the increasing trend to continuous smelting and converting, granulation of copper matte is gaining prominence as a means of decoupling the smelting and converting operations. Moreover, granulation is also being seen as a possible avenue to using higher grade oxygen in converters. By feeding cold solid matte, the oxygen concentration can be increased to compensate for the lower enthalpy feed. This leads to a higher grade of SO2 in the off gas and a lower total flow rate. Current granulation technology relies on the cooling of a falling matte film by water jets. This technology while effective has several drawbacks including those related to safety. Noranda and McGill University have developed a new process (patent pending) for solidifying copper matte (or slag). It overcomes many of the negatives of current technology. The system is based on an air cooled twin roll caster. This: new system uses no water and instead incorporates heat pipe technology to transfer the heat from the solidifying matte to the cooling air to produce a thin strip of 1 to 2 mm in thickness. Testing of a prototype unit demonstrated its viability. This paper describes this newly developed, twin roll casting system that is completely waterless. The advantages of this process as well as the findings from several tests are also detailed.

Jan 1, 1999

By Z. S. Wronski

In rapidly solidified Fe-Nd-B permanent magnet alloys, the content and distribution of Nd-rich intermetallic and Fe-phases determine coercivity Hc and remanence Br. Consequently, microstructure plays a crucial role in deter- mining the (BH) max-product of permanent magnets fabricated from these alloys. A study has been initiated to investigate changes in microstructure and the effects on magnetic properties as the material is processed from arc-melted ingot to melt-spun flakes and finally to a product consolidated by hot-forming. Anisotropic magnetization behaviour has been observed in rapidly solidified flakes after low-temperature annealing.

Jan 1, 1989

By Cristiän Vargas, Jaime Simpson, Gerardo Cifuentes

"This paper presents a new process for the precipitation of Sb and Bi present in copper refinery electrolytes in the presence of Pb02 (Chilean Patent No. 45,037). To establish the conditions under which the precipitating compounds form, it was necessary to evaluate the amount of PbCh consumed, antimony extraction efficiency, precipitate stability, reaction kinetics, diffraction analysis and X-ray fluorescence, separation of size, plus observation of the precipitates in the electron microscope. Preliminary tests were carried with synthetic copper refinery electrolyte, and then the final testing was done with electrolytes from Chilean refineries. This process provides a real alternative for the treatment of copper refinery electrolytes for the control of Sb and Bi in solution; it is very simple to operate and is low cost compared with competing processes.Introduction.A high quality copper cathode implies a cathode free of impurities. The electrorefining process seeks to eliminate these impurities from the copper anode (99.5% purity) by its dissolution in an acid electrolyte using chemical and electrochemical reactions. As a result of this process, a cathode (99.99% purity) is obtained. If the concentration of impurities in the electrolyte, from the dissolved anodes, begins to increase; particularly if the antimony concentration in the electrolyte increases up 500 ppm, the formation of floating slimes which are a major cause of contamination of the cathode is favoured. The most important impurities from the point of view of their effect on the quality of the cathode copper, are Ag, As, Sb, Bi, Pb, Se and Te. Silver is necessary for the control of Se and Te. To control all of these impurities, it is necessary to establish different methods or parameters of control in copper electrorefining. These parameters are anode composition, additives, purification of the electrolyte, current density, acidity, etc."

Jan 1, 2012

By N. L. Piret, E. N. Mounsey

Ausmelt technology is successfully used to process primary and secondary materials to produce lead in large-scale commercial operations and to meet stringent environmental standards. The development and commercial data covering these applications and the results with respect to metallurgical, cost and environmental performance are reviewed in commercial operations. A new smelter is scheduled for commissioning in 2000 at Korea Zinc's Onsan site to process lead fume and other secondary materials to produce 50,000 tonnes per annum of lead bullion. The unique features of Ausmelt technology also allow for the efficient processing of polymetallic concentrates and secondary materials, particularly copper and lead, through the effective separation of these elements into metal, slag and fume species. This capability has been successfully demonstrated at a commercial scale and the results and implications for the industry are discussed.

Jan 1, 2000

By C. M. Acuña

At the Chuquicamata Division of Codelco-Chile high arsenic concentrates are produced, which at the smelter are processed via the Outokumpu Flash Furnace and Teniente Converters to obtain copper mattes. In the case of the Teniente Converters the production of matte grade near white metal composition is a common practice since the eighties and provided in the pyrometallurgical route no appropiate measures are taken, penalties have to be paid because of arsenic content in the anodes. During smelting huge volume of slag is produced and elimination of arsenic by slagging at this step is not economically attractive. Although during fire refining is possible to eliminate arsenic by use of mixtures of calcium and sodium carbonates this alternative is expensive, takes long process time and decreases the lifetime of the refractory lining. In spite of these facts a reasonably way to control arsenic in metal, and therefore in the anode, is taking, action in the converting step. The effects of oxygen and arsenic content in metal, arsenic in white metal and basicity index of the slag upon the distribution coefficient of arsenic between metal and slag were investigated at pilot and industrial levels. The best results are obtained for metals around 7,000 ppm oxygen and 0.3 basicity index slag, which results in a 5.7 distribution coefficient for a 5,800 - 7,100 ppm arsenic content in white metal, 18%-24% CaO slag at 1473 - 1523K. Furthermore, no significant/visible refractory wear has been realized.

Jan 1, 1999

By Maria Margarida Lima, Maria Lucelinda Cunha, Dora Algarvio

"The main goal of the present work is the quality improvement of the recycled aggregates produced by a construction and demolition waste (C&DW) recycling facility located in Montemor-o-Novo, Portugal. The recycling process was developed on a pilot plant scale with 50 t/h of capacity. Process operations are the hammer mill comminution, magnetic separation and screening.In order to improve the knowledge on the C&DW, a characterization procedure was implemented by hand-sorting, magnetic and density separation on representative samples. On the other hand, to improve the quality of the produced aggregates, the bar screen size fractions were analysed, according to the Portuguese Standard (NP EN 933-1 2000).Wood was identified as the critical contaminant, representing 17% by weight of the total contaminants. Sieving results showed that about 97%, 76%, 56%, 98% and 57% were on the correct size range, which lower results are probably due to the type of screens and/or the material characteristics of the recycled aggregates.IntroductionThe construction and demolition waste problemConstruction and demolition waste (C&DW) is generated by the construction activity, resulting from both, buildings or other structures construction and old structures demolition. As a reference, it can be told that C&DW comprises about 40 to 50% of rubbish (concrete, asphalt, bricks, blocks and dirt), 20 to 30% of wood and related products and 20 to 30% of miscellaneous wastes [1]. In Portugal, C&DW is classified in the LER (Portuguese nick name for the European Waste List), Chapter 17, and includes a diversity of wastes, like concrete, bricks, ceramics, bricks, wood, glass, plaster, copper, zinc, lead, iron, steel, as well as insulation and roofing materials. C&DW stream has several characteristics which make it particularly difficult to deal with and are summarized in the following five items.(1) Lack of information on quantities generated: In Portugal, the C&DW sector has been neglected over the past years, which meant that there are not consistent information concerning the quantities and composition of these wastes yet. Several estimates, based in different assumptions, indicate different results, which may vary from 219 Mt to 10 931 Mt [2]."

Jan 1, 2008

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By Chi Ru?an

Sollutions of ammonium chloride, nitrate and sulfate were studied in extraction of rare earths absorbed on a low-grade, kaolilnitic ore recently discovered in southern China. The results of percolation leaching tests and the recovery of the rare-earth values from these solutions are presented.

Jan 1, 1989

By Chu Yong Cheng

Synergists can be used in solvent extraction to improve the selectivity of extractants for metals. Research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy / CSIRO Minerals has shown that the pH isotherm of nickel with Versatic 10 was significantly lowered by the addition of the synergist Acorga CLX50. The paper discusses how this synergistic shift can be used to alleviate a gypsum formation problem at Bulong nickel laterite operation in Western Australia. Metal pH isotherms were obtained with Versatic 10 and synergist CLX50 using synthetic leach solutions. In terms of pH50, the extraction order of the metals with 0.5 M Versatic 10 alone was Cu > Zn > Ni > Co > Mn > Ca > Mg, whilst the extraction order with Versatic 10 and 20% by volume CLX50 was Cu > Ni Zn > Co > Mn > Ca > Mg with the pH50 (Mn-Co) significantlyincreased. This is significant because the isotherms of valuable metals Ni, Cu, Co and Zn shift more towards low pH than those of the waste metals Mn, Mg and Ca, resulting in a possible good separation of Ni, Cu, Co and Zn from Mn, Mg and Ca. The use of intermediate precipitation, solids/liquid separation and re-leach in the three Western Australian nickel plants make these processes complicated and costly in capital and operation. The research work carried by the SX groupat the AJ Parker Centre has led to the development of direct SX (DSX) processes to recover nickel and cobalt from leach solutions using synergistic organic systems. Semi-continuous tests with a BHP Billiton pilot plant leach solution showed that Ni and Co together with Zn and Cu were separated from the major impurities, Mn, Mg, Ca, and Cl, in the first SX circuit. The co-extracted impurities were easily scrubbed. After stripping, Ni and Co together with Zn and Cu were concentrated, resulting in a much smaller second SX circuit in the down stream processes.

Jan 1, 2003