Search Documents

By G. T. Lapidus, O. J. Solis-Marcial

"The oxidative dissolution of copper from refractory minerals, such as chalcopynte, represents a technological challenge that has occupied hydrometallurgists for more than half a century. Innumerable processes have been suggested, but the majority operates at high temperatures or employs corrosive media. The origin of this refractory nature is the formation of passivating phases of iron(III) or copper. One option is to add non-corrosive ligands that complex these metal ions, thereby facilitating their dissolution. In the present work, the effect of acetone in sulfuric acid solutions was studied. The initial experiments were on chalcopynte carbon paste electrodes using cyclic voltammetry, where greater reactivity was observed. Later, leaching tests with hydrogen peroxide, cupric sulfate and ozone and, as oxidants, were performed. High extractions were achieved in three hours at 50°C. The solid residues contained the iron in the form of Fe203 and FeOOH.IntroductionChalcopyrite is the most important mineral of polysulfide copper ores [1] and accounts for approximately 70% of the world's copper reserves [2]. Currently, the copper present in chalcopyrite is extracted mainly by pyrometallurgical processes, which generate environmental concerns because of the formation of SO2 gas and submicron particulates [3]. The development of a less aggressive hydrometallurgical process for the extraction of copper would constitute a possible solution to these problems. For that reason, studies of the dissolution behavior of chalcopyrite are of great technological importance [4], However, the proposed oxidative leaching routes for chalcopyrite, generally at high pressures and temperatures, have not been implemented on an industrial scale, because of the elevated costs required to equal the high copper extractions obtained in thermal processes. These extreme leaching conditions are required because of the refractory nature of chalcopyrite. Passivation has been used to explain this phenomenon, although researchers have disagreed on the composition of the layer, which is various have assumed to be sulfur, copper sulfides, and iron-bearing jarosites or hydroxides [5]. If the latter compounds are the cause, an alternative solution would be the use of polar organic solvents in the oxidative leach to decrease the formation of the passivating iron layer. In this work, the influence of acetone on the oxidative leaching of a chalcopyrite concentrate at room conditions is explored."

Jan 1, 2012

By E. M. Weenink

A proposed alternative to the conventional zinc extraction processes is the flash reduction of zinc calcines. As part of an overall study of this process, the kinetics of single zinc oxide pellets were investigated. Pellets, compacted from Outokumpu zinc calcine (60.9% zinc, 9.6% iron), were suspended in a flow of CO/CO, mixtures and reduced at temperatures between 1000 and 1200°C and atmospheric pressure. The pellet weight loss with time was recorded and analyzed. It was found that the reduction of calcine pellets (0.9 cm height and 1.36 cm diameter) was controlled by chemical reaction. This paper includes an analysis of the experimental results of two previous investigations of ZnO reduction.

Jan 1, 1992

By Ana E. Bohé, Georgina De Micco, Gastón G. Fouga

"In this work the reaction between several manganese oxides and chlorine is investigated in the range of temperatures between 650 and 950ºC. The reaction path for the chlorination of MnO is established, which involves recrystallization of high valence manganese oxides (Mn3O4 and Mn2O3) followed by its chlorination. For this reason, to understand the reaction of MnO, the chlorination of Mn3O4 and Mn2O3 has also been studied. The starting temperature for the reaction of these oxides is determined by non isothermal thermogravimetric measurements. The effect of temperature is analyzed, under our experimental conditions the rate of reaction is mass transfer controlled. The activation energy for the volatilization of manganese chloride is obtained which is in good agreement with volatilization enthalpy of MnCl2.IntroductionMany oxide ores which have manganese in their composition undergo chlorination processes during the extraction of refractory metals such as Ti, Hf and Nb. Although several works related with chlorination of manganese oxides were reported, there is no information about the kinetics or mechanism of the manganese oxide chlorination reactions. Okahara et al. studied the chlorination of manganese oxides and established that they react easily above 250ºC. Furthermore, they observed that chlorination of high order oxides is more difficult when there is not a reducing agent [1]. Ivashentsev studied the chlorination of manganese oxides using Cl2(g), CO(g) + Cl2(g) and COCl2(g). He established that the reaction of MnO started at 130ºC with formation of MnCl2(s), he also observed recrystallization of manganese sexquioxide [2]. Finally, the chlorination of manganese nodules from the ocean was studied by Murthy and Reddy [3] with the aim of obtaining valuable metals such as Mn, Co, Ni and Cu. They studied the influence of several parameters like temperature, carbon percentage, particle size and chlorine flow rate in the extraction process."

Jan 1, 2008

By D. Q. Cang, G. Duan, H. X. Li, H. Bai

"Life cycle assessment (LCA) is a valid environmental evaluation method and enterprise environmental management tool used in industrial ecology areas. In this paper LCA was newly used to evaluate the environmental impact of manufacturing of alumina by Bayer process in china from two aspects of logistics and energy flow, GaBi software acted as analysis tools with evaluation model established, and several environmental impact assessment criteria were selected based on the actually typical date of Bayer alumina producing process. Evaluation results show that alumina manufacturing by the Bayer process has a great impact on the global warming and human health of respiration, even roasting process gives rise to the greatest impact of winter fog index. Scenario analysis proposed ways of reducing environmental load caused by Bayer process including: (1) the economic and efficient use of mineral processing technology; (2) optimization of energy use, saving power consumption or the use of new more economical source of energy; (3) actively promote the use of innovated technology and equipment in alumina manufacturing and waste such as red mud utilization process.1 IntroductionSince 2002, China is already the world's biggest producer of aluminium, in 2007, China aluminum production has accounted for above 1/3 all over the world, 2009 for 13 million tons and to the end of 2010, China aluminum production is expected increased to be over 15 million ton [1,2,3]. While as the raw material for producing aluminum the alumina production in china has up to 19.46 million tons of the world's total quarter in 2007, by the end of 2009 China alumina production has achieve to 23.78 million tons [4,5]. China has rich bauxite resources with proven reserves about 23 million tons, but the great majority of china bauxite is hard monohydrate diaspore type with low ratio of aluminium silicon, high impurity content and poor aluminum dissolution performance, that cause high energy consumption, long and complex process, high production costs and heavy environment load[6,7]. Before most used alumina production was sintering process rather than Bayer method in china, over the past decade Bayer method has been widely applied instead of sintering process or combination both forming joint process, premise is improving bauxite quality by mineral processing or adding imported rich bauxite mineral[6,8]. In general each ton production of alumina needs bauxite 1.6~2.20t, limestone 0.7~1.7t, soda 0.250kg, fresh water 12.30 cubic meters, in addition to consume large amounts of energy, and emission waste water over 8.0 cubic meters, dust 2.3~5.7 kg, red mud 0.8-1.5 tons. In china Red mud yield nearly 30.0 million tons every year, accumulated stock is approximately 0.2 billion tons, by 2015 accumulative total red mud is expected to reach 0.35 billion tons [9-13].We know aluminium industry and alumina production have produced large waste, make large energy consumption and its environmental impact could not be ignored. Expecting to optimize production processes and achieve resource recycling for this industrial process the proper environmental assessment is very necessary. Currently Life Cycle Assessment (LCA) is generally recognized as the approved tool to achieve the purpose. The essence of LCA tool is to examine, identify and evaluate a kind of materials, product, process, or a system of environmental impact in their whole life cycle. The life cycle of materials or products includes whole process from raw materials obtained to the final disposal, or more ideal with original or other forms of the whole process of recycling [14-17]."

Jan 1, 2011

By C. T. Philipp

Recycling of waste is much preferred over disposal. This paper discusses the Enviroscience, Inc. (ESI) process, now being commercialized by MetWool, Inc., to recycle hazardous wastes using an extractive metallurgical process which is followed by vitrification of non-reducible metal oxides. In this process, volatile and reducible metals are reclaimed as their respective oxides and elements.

Jan 1, 1995

By Olexandr Gydin

The evolution of grain and dislocation structures during cold deformation of the new steel LH800 of Salzgitter AG is investigated in the frame of this work. The main feature of this material is its ability to air-harden by carbon content of about 0.1%. The initial ferrite structure of the metal provides high plasticity at cold deformation and subsequent heat treatment increases tensile strength approximately two times. Described are results of in-situ tensile tests in the SEM. SEM and TEM analysis of grain and dislocation structures evolution in samples, which have been uniaxially deformed to certain strains, are carried out. After statistical evaluation of results the grain elongation against strain is determined. A microstructure of a deep drawn cup is analyzed by means of SEM. A quantitative evaluation of grain elongation on the different cup zones and comparison of these data with prediction results based on tensile tests are carried out.

Jan 1, 2009

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting, lime roasting, is being tested fro retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04), oldhamite (CaS), calcium sulfite (CaS03), hematite (FenOs), magnetite (Fe304), and minor amoupts of pyrrhotite (Fel.,S) and pyrite. At 600°C, 650°C and 700°C the main constituents are anhydrite, oldhamite, and hematite. At 750°C, 800°C, and 850°C anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides, calcium sulfite, hematite, and minor oldhamite, magnetite, and pyrrhotite. At 650°C 700°C 750°C and 800°C, anhydrite, oldhamite, arsenic sulfides, and hematite are present. At 850°C, the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CLM) in the determination of the calcium-sulfur- oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RLM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1993

By Yafei Xiong, Yue Wang, Guotao Xu, Shuzhong Li, Huaiyuan Li

"The composition, properties and structure of taphole clay with high strength and friendly surrounding used in a new blast furnace with 3800 M3 volume was studied. The developed taphole clay had been applied in the blast furnace for four months, pouring times were 11-13 every day, flowing rate of hot iron was 7.5 t/min and the consumption of taphole clay was 0.49Kg per ton iron, which can make the new blast furnace attach the designed production quickly and decrease the cost of hot iron. The taphole clay is easy to be opened in the channel of hot iron which can be remained in stable shape under the corrosion of slag or hot iron, and it dose not produce poisonous smoke in yellow or dark color in the use process. The development of new taphole clay is useful to improve the work surrounding of the blast furnace.IntroductionIn the iron-making process, the taphole clay's function is filling up the taphole and protecting the formation as well as the growth of the clay in the blast furnace, maintaining the enough taphole depth; simultaneously it is easily to open a hole and knock out the clay. The taphole clay has a good performance of molten slag and hot iron resistance. The traditional taphole clay uses coal tar or carbolineum as a binder, and the performance of taphole clay is good, but it has the black and yellow poisonous smoke, which is harmful for work condition. Through the investigation on the binder's composition and poisonous performance of taphole clay, the environmental taphole clay is developed by some foreign companies, which is named the third generation product with benzene is less than 300ppm, and it has been used in European steel companies. This application of the taphole clay with high strength and environment-friendly using in 3800m3 blast furnace is introduced and the performance is discussed and analyzed in this paper."

Jan 1, 2012

By Jim Hardy, Tim McKnight

"The thermal mass flow controller, or MFC, has become an instrument of choice for the monitoring and controlling of process gas flow throughout the materials processing industry. In the semiconductor industry, these MFCs are used on over 70% of the processing tools. Reliability and accuracy are major concerns for the users of the MFCs. Calibration and characterization technologies for the development and implementation of mass flow devices are described. Sources of inaccuracy in process gas handling are described, and a model to correct for these inaccuracies is outlined. A gravimetric calibrator is described that allows flow sensors to be calibrated in corrosive, reactive gases to an accuracy of 0.3% of reading, at least an order of magnitude better than previously possible. All described capabilities are implemented in a Department of Energy User Facility which is available to industry and universities to test and develop gas flow sensors and controllers and evaluate their performance related to environmental effects, reliability, reproducibility, and accuracy.IntroductionMaterials processing is at the heart of semiconductor manufacturing. To make today's advanced integrated circuits, silicon wafers are subjected to over 200 process steps. Most of these steps involve processes such as etching, implanting, diffusion, annealing, deposition, and lithography (resist deposition and hardening). Often one or more process gases are used to complete the process step. To achieve the quality and performance required in the micro devices, accurate measurement and control of these gases is essential. The Oak Ridge National Laboratory (ORNL), in conjunction with the semiconductor industry, has been working to improve process gas measurement and control accuracy and reliability. Standardized test methods have been developed to characterize and benchmark the performance of mass flow controllers (MFCs), the method of choice for monitoring and controlling gas delivery. Testbeds have been designed and fabricated to produce repeatable and accurate data using these standards. Baseline testing was performed along with development of a unique mass flow instrument, the gravimetric calibrator."

Jan 1, 1997

By Cleusa Cristina Bueno Martha de Souza

Nowadays in Brazil the final disposal for spent batteries include sanitary and industrial landfill for hazardous waste from domestic waste and industrial waste respectively. The problems of environmental impact caused by spent batteries had been discussed of several years, considering the fact of metals contents, like Cd, Hg, Pb and Zn. Some techniques are been proposed for recycling this type of waste in order to protect the environment while bringing also economic advantages of recovering metals. The reclamation of metals from secondary raw materials had been employed and further applications of this flexible technology are planned to the future. The processing of metals solutions involving hydrometallurgical techniques is an efficient method for recovering metals, since it provides completely recovery of metals with low energy requirements. This paper discusses the spent alkalline batteries characterization and leaching stage experiments results with sulphuric acid as leachant. After batteries dismantling by mineral processing techniques, the black powder sample produced was submitted to diffraction X-ray characterization and atomic absorption spectrophotometry in order to verify all the substances presented. Some experiments were carried on to develop a hydrometallurgical process for initial metal recovery aiming to get Zn into a soluble form on aqueous solution in order to propose the next stages of purification and recovering Zn, as electroplated deposition. The sulphuric acid was chosen not only for being cheaper than other leachants but also for improving the extraction of soluble Zn as ZnS04 form at diluted acid concentration. Batch laboratory experiments leaching procedure were conducted to determine appropriate leaching conditions from the viewpoint of maximize zinc extraction. In these tests an amount of dry powder batteries was added to different acid concentrations and solid/liquid ratio and after leaching and filtration the aqueous solutions were submitted to atomic absorption spectrophotometry analysis to verify the Zn content.

Jan 1, 2000

By G. A. Brooks, R. W. Matusewicz, Nazmul Huda

"A computational fluid dynamic (CFD) model of a conventional tuyere blown slag fuming furnace has been developed in Eulerian multiphase flow approach. The model was developed by coupling CFD with kinetics equations developed by Richards et al. for zinc fuming furnaces. The model integrates submerged coal combustion and chemical reactions with the heat, mass and momentum interfacial interaction between the phases in the system. The model predicts the velocity, temperature field of the molten slag bath, generated turbulence, vortex and coal utilization behavior from the slag bath. The highest coal penetration distance was found to be at l/L = 0.2, where / is the distance from the tuyere tip and L is the total length (2.44m) of the modeled furnace. The model also predicts that 10% of the injected coal bypasses the tuyere gas stream un-combusted and carried to the free surface, which contributes to ZnO reduction near the free surface.IntroductionSignificant metal values are often discarded with slag in the form of metal oxide produced by the smelting industries. These metal values can be recovered from the slag by proper treatment. Zinc slag fuming is such a process, where a reductant source (usually coal) is injected in the molten slag bath to reduce dissolved ZnO from the bath into metallic zinc vapour. The process can be carried out in either conventional tuyere blown furnace or top submerged lance (TSL) smelting furnace. Conventional slag fuming processes are carried out on batch basis in a rectangular tuyere blown furnace. Approximately 50 tonnes of charge (either molten slag or solid slag) is fed to the furnace at the beginning of each fuming cycle. Two opposing sets of submerged tuyeres are employed to inject air and pulverized coal into the molten slag bath to carry out combustion and reducing reactions."

Jan 1, 2012

By J. A. Gonzalez-Dominguez

During the electrorefining of lead by the Betts process, ionic concentration gradients become established within the slimes layer. These gradients contribute to precipitation of secondary products and to gradients in electrode potential applied to slimes filaments, and thereby affect the dissolution of noble impurities. This paper describes the experimental results obtained when a typical lead anode was dissolved under galvanostatic conditions with concurrent interruption of current at preset slimes thicknesses. Reference electrodes were incorporated within the lead anode to follow the potential gradients across the slimes electrolyte. Samples of the slimes electrolyte were withdrawn in-situ and their compositional changes were related to transport processes across the slimes layer. Upon current interruption the anodic overpotential decays, first abruptly (as the uncompensated ohmic drop disappears), and then slowly (due to the presence of a back E.M.F. created by ionic concentration gradients that decay slowly). Current interruption measurements showed that: (A) concentration gradients exist across the slimes layer, (B) inner solution potentials within the slimes layer can be larger than those measured from reference electrodes located in the bulk electrolyte, (C) secondary products can shift the inner solution potential to negative values that reverse upon re-dissolution and (D) ionic diffusion is seen upon current interruption but it is complex and difficult to model due to the presence of processes that can support the passage of internal currents. SEM and X-ray diffraction analysis of the slimes filaments indicated that secondary reactions leading to the formation of Si02 and PbF2 take place (mainly at the anodelslimes interface). The onset of these reactions and their relationship to the Pb-F-Si-H20 Eh-pH diagram are linked to the industrial operation of the Betts process.

Jan 1, 1994

The paper describes the propensity of tin to form intermetallic compounds with microalloying elements such as Nb, Ti and aluminium, which are commonly used as additions to achieve particular combination of strength and toughness. Two series of alloys were prepared by arc melting under an argon atmosphere. Each series was based on Fe, Sn and A1 with either Nb or Ti additions. The microstructures were studied using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and microprobe analysis. It was found that the level of Nb addition has an effect on the formation of Sn-rich compounds. For small Nb additions, no Sn containing compounds were found, whereas in higher Nb alloy, a Laves phase (FezNb, hexagonal, a = 0.4830 nm and c = 0.7879 nm) containing about 1 at % Sn was found. A FezNb3 phase (cubic, a = 1.1261 nm) associated with the formation of alumina was also found but did not contain tin. No Sn containing compounds were found with Ti additions. The experimental observations have been compared with thermodynamic calculations performed using MTDATA.

Jan 1, 1999

By Sylwia Zymankowska-Kumon, Rafal Danko, Mariusz Holtzer, Artur Bobrowski, Michal Kubecki

"Moulding sands with furan resin constitute constantly growing part in technologies of producing castings from iron alloys. Due to the presence of harmful substances in resins such as furfuryl alcohol, phenol and formaldehyde, using those mould sands may be hazardous to the natural environment and workers. The general assessment of harmfulness of sands used for molds and cores encompasses 2 basic points: emission of hazardous substances during processes of preparing sands, pouring mold with liquid metals (high temperatures), cooling and shaking-out; possibility of washing out hazardous substances from used sands to the environment, during storage or economic use outside foundries. We present the results of research on the assessment of harmfulness of mould sands with furan resin in the scope of the above points. The research was conducted according to the original method prepared by the authors, which has been used for years in cooperation with various foundries (Poland, abroad).IntroductionSands are used by the foundry industry to create metalcasting moulds, where the individual sand grains are typically bound using bentonite clay and carbonaceous additives or resins. During the casting process, the moulds can be exposed to temperatures as high as 1500°C depending upon the metal being poured. The molten metal causes thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics that are emitted to the atmosphere and condense in the moulding sand [1]. The moulding sands are reclaimed within the foundry, but part of them are eventually discarded in landfills, because it is not longer suitable to make metalcasting molds [2, 3]."

Jan 1, 2013

By D. Morin

A general study of gold refractory arsenopyrite-pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 I unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery. Furthermore. the arsenite and ferrous produced in solution have to be oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimization study calculation for scaling-up the design and power requirements of an industrial installation. For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution. In that conditions the power cost is quite marginal. actually it is significant for the treatment of pure pyrite.

Jan 1, 1991

By Xiaojian Zuo, Yihua Han, Qingguo Xue, Jingsong Wang, Lintao Wang, Rongzong Lan

"Using the facility of reduction experiment, the low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace (OBF) were studied. Through analyzing the results, the difference of pulverization and reduction behavior of sinter in OBF and conventional blast furnace (BF) were discussed. Furthermore, the effect laws of reduction temperature and the content of CO and H2 on reduction behavior of sinter were studied. Also the controlling step of iron oxide reduction was discussed. Compared with BF, the low temperature reduction pulverization of sinter became serious at 773 K; reduction rate became faster at 1173 K; reduction time became less and final reduction degree was increased in OBF. With increasing of H2 and CO contents, the reduction of sinter was promoted. The reduction process was controlled by interface chemical reaction at the earlier stage and by interface chemical reaction and internal diffusion at the final stage.IntroductionThe new ironmaking technology of Oxygen Blast Furnace (OBF) is most likely to be used in large-scale application process. The concept relies on the removal of the CO2 contained in the top gas of the blast furnace. Therefore the useful components, i.e. CO+H2, can be recycled back into the furnace and reused as reducing agents. In addition, injecting oxygen (O2) into the furnace instead of preheated air, removes unwanted nitrogen (N2) from the gas. Under the pressure of CO2 emissions in iron and steel making, the growing international shortage of coking coal resources and the rising price of coke, OBF has attracted attentions of both domestic and foreign researchers, because it has so many advantages such as high productivity, high PCI rate, low coke rate, high gas reducing capability and high top gas calorific value, etc [1-7]. As a result of recycling most of the top gas after CO2 removal and injecting oxygen into the furnace, the reduction capacity of blast furnace gas will be increased, so the metallurgical behavior of OBF's iron burden is different from traditional blast furnace. Therefore, it is one of the keys to develop this technology, which studies the metallurgical behavior of sinter in OBF. The purpose of this paper is to study the low temperature reduction pulverization and reduction behavior of sinter at the atmosphere of OBF, which includes the difference of low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace and conventional Blast Furnace (BF). It will provide theoretical basis for the development of OBF."

Jan 1, 2012

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By Nagy El-Kaddah

"One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100 u. inclusions· are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate the capability of the system for producing super-clean metals.IntroductionThe nature of extraction, refining and processing of metals is such that oxides and other non-metallic particles will always be present. This is due to the highly reactive nature of metals with oxygen and other non-metallic elements. The presence of these type inclusions in metals, even in minute amounts, can seriously flaw the reliability and performance of the final product. They not only reduce the strength and the stiffness of the metal/1/, they are the reason behind many of manufacturing defects such as porosity in castings, surface and internal cracks in continuously cast ingots and rolled products, etc., which act to cause premature failure of manufactured parts. In fact, for critical applications such as turbine blades, there is virtually no tolerance for inclusions above ten microns in size /2/. Therefore, removal of inclusions from the liquid metal is an essential processing step.The demand for cleaner metals has brought major changes in the technology and practice of metal refining and casting. Inclusion removal from the melt is currently achieved by passing the melt through a series of melt treatment systems, including induction stirring furnaces, argon-stirred ladle, and ceramic foam and deep-bed filters /3,4/. These systems are generally capable of removing all inclusion particles above 50 microns in diameter, which meets current cleanliness requirements for most applications. However, they may not be able to meet the projected cleanliness levels for critical applications due to kinetic and operational limitations of these systems in removing smaller particles /5/."

Jan 1, 1996

By Desmond Cook, Cynthia P. Dogan, Dale Govier, Gary Korth, James C. Rawers

"The microstructural and mechanical properties of iron powders processed in an attrition mill are highly dependent upon the processing environment. Extended high-energy ball milling in argon resulted in nanocrystalline bcc-Fe microstructure, while processing in nitrogen or alloying with carbon resulted in both nanocrystalline bcc-Fe and bct-Fe microstructures. In this U.S. Bureau of Mines study, both X-ray diffraction and Mössbauer analysis were used to show that the infused carbon and nitrogen concentrations were predominantly on the grain boundaries. Explosive consolidation resulted in a fully dense product with microstructure similar to the microstructure of the mechanically processed powder. Hardness values of the compacts correlated highly with grain size, independent of the processing conditions.IntroductionNanocrystalline materials have been theorized and shown to have unique properties that make them interesting for material scientists and promising for material engineering applications. Several conferences have been devoted solely to the techniques of preparing nanostructured materials have been held(l,2,3.). To date, most techniques used to generate nanocrystalline materials produce only a few grams of particles(1). High-energy ball-milling, however, is an efficient and effective technique that can produce substantial quantities of nanocrystalline materials with homogenous chemical composition that cannot be produced by conventional processing techniques(3).Applications and material evaluations of nanocrystalline materials require several grams of solid samples. Because nanocrystalline microstructures' are thermodynamically unstable, producing consolidated macro structures of nanocrystalline material has proved to be very difficult(2,3). In particular, retention of the nanocrystalline microstructure during consolidation of nanocrystalline particles has proven to be a problem. In contrast to many consolidation techniques that require elevated temperatures, explosive compaction uses a shock wave for consolidation( 4,5)."

Jan 1, 1994