Search Documents

By Mohamed Ahmed, A. Kawy

"Smelting of scrap copper and residual anodes and cathodes carried out in a reverberatory type furnace. In this, deoxidation process is carried out by wood, which acts as a resource of reduction gases such carbon monoxide, hydrogen and methane. Use of wood causes the formation of soot pollutants and efficiency of oxygen removal from copper is low leading to added costs in removing contaminants. This expensive problem was solved by using of reformed natural gas as a source of reduction gases (CO+ H2).IntroductionThree reverberatory furnaces were used for smelting of scrap copper and residual anodes and cathodes. Each furnace had a 7tpd capacity and was operated at 1183 °C.In this furnace, Step1-compressed air supplied by tubes from the side of the furnace to remove sulfur from copper matte by oxidation .The copper is also oxidized to copper oxide .[1]Step 2- copper from matte is deoxidized by a reductant. Typically deoxidation process is carried out using wood as a resource of carbon monoxide, hydrogen and methane which are the reduction gases. Use of wood causes the following:1- Forms soot pollutants2- Oxygen removal efficiency from copper is low; more contamination in copper matte increased energy in deoxidation3-the process is highly expensive.In the recent trends, this problem has been solved by using reformed natural gas as a source of reduction gases (CO+ H) .This results in 1-Reduced pollution during smelting.2- High efficiency in the removal of oxygen from copper to produce oxygen free copper. The surface of copper produced from this method is smooth which helps in forming and machining.3- Low cost and natural gas is more readily available in Egypt than wood."

Jan 1, 2010

By Pekka Taskinen, Hannu Johto

"Copper sulfide concentrates often contain impurities such as lead and iron. The phase stabilities of the sulfide impurity systems in metallurgical process conditions are in many cases unsatisfactorily known. Thermodynamic information of a system gives better understanding of its behavior of metal making processes, but also has effects on the economic and environmental factors of the production process. In this study, isothermal equilibrium and quenching experiments of the stable phases of the system Cu2S-FeS-PbS at 700 and 900 °C were carried out and based on the experimental results, Gibbs triangle of equilibrium phases of the system was outlined.IntroductionThe knowledge of stabilities of phases and the thermodynamic properties of many sulfide systems in the temperature range of 500-1200 °C are quite limited. Especially, the knowledge of liquidus surfaces of multicomponent sulfide systems is essential for making many metallurgical processes more environmental friendly and allowing the utilization of complex concentrates. In this work, the aim was to investigate the phase stabilities of the quasiternary system CU2SFeS- PbS using evacuated silica ampoules. Of greatest interest were the properties of the liquidus surface in the system, in order to be able to predict better the formation of a liquid phase in metallurgical processes."

Jan 1, 2012

By Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide (CO2), a major component of the greenhouse gases, could be comprehensive utilized as a valuable resource to oxidize vanadium during the converter vanadium extraction process. The thermodynamic software, FactSage, was utilized to study the oxidation ability and theoretical cooling ability of using weak oxidant CO2 as coolant in vanadium-containing hot metal. Besides, experimental research on vanadium extraction in CO2 and O2 mixed blowing extracting process had been undertaken. The results indicated that the elements C, Si, V, Mn etc. could be oxidized by weak oxidant CO2, and the content of V2O3 in slag was approached to pure O2 blowing. Furthermore, CO2 had a remarkable cooling ability and the molten bath temperature kept on decreasing as CO2 blowing rate increases. This research has proved that CO2 and O2 mixed blowing in vanadium extraction process are effective.

Jan 1, 2015

By Li Kaihua, Li Liang, Miao Qingdong, Wang Cong

The current process of production of titanium sponge involves the use of TiCl4 as a feed material and a huge amount of heat is generated during the magnesiothermic reduction process. For this reason, it is possible to agglomerate into a titanium lump with the partial high temperature. And, it is difficult to obtain soft titanium sponge with low content of impurities. In order to solve the current problems in the titanium sponge production process, process optimization experiments study of TiCl4 feeding speed, vacuum distillation temperature, system pressure and time control had been conducted for obtain high quality titanium sponge. Experimental results show that lower feeding speed can improve the output capacity of titanium sponge and softer products can be obtained. The product grade rate of titanium sponge improved significantly.

Jan 1, 2015

By S. Kurama

Incorporation of de-watering sieve waste of borax (TSW) from Etibor Kirka Borax Company (Turkey) on the mechanical and physical properties of a commercial floor tile composition was investigated. In order to achieve this aim, TSW was partially employed in place of feldspar in the standard composition up to 20 wt %. The formulated compositions were wet milled, dried, shaped and then fired at 1190C for a total firing time of 38 minutes (from cold to cold) under industrial conditions. It was found that using of TSW up to 15 wt % improved the physical and mechanical properties of final product. The results indicated a good prospect for TSW as a co-flux in floor tile formulations.

Jan 1, 2006

By Geir Wedde, Anders Sorhuus

"Vast quantities of energy are released as heat to the environment from industrial operations. Many countries target waste heat recovery to mitigate CO2 emission. Exhaust gases from industries such as primary aluminium smelting, carry a substantial portion of the waste heat generated. For a cost efficient capture of more valuable heat (higher exergy), heat exchangers should operate on the exhaust gases upstream of the gas treatment plants. Heat exchange surface would be exposed to dust laden gases with risk of fouling. Heat exchangers of innovated design and operation have overcome the potential of excessive fouling rates. Heat exchangers of the ""shell and tube"" design have been demonstrated for exhaust gases from ferroalloy as well as primary aluminium smelters. In addition to the heat recovery, gas cooling results in smaller gas treatment plants with lower costs and reduced emission. The aluminium experience is exampled in the paper.IntroductionIndustrial usage of energy continues to grow as a result of increasing volumes of production, a trend that is likely to continue in the coming decades as living standards keep rising globally. World energy consumption (Figure la) is to grow 49 % by 2035 (ref. 2010) as reported by EIA [1]. The industrial sector consumes somewhat more than 50% of the total world energy consumption predominantly the energy increased demand comes from non-OECD countries in Asia. The industrial consumption by production of metals iron and steel accounts for 14 % and for non-ferrous metals 3 % mostly for aluminium production (Figure lb). Aluminium production will be discussed in this paper as an example of an industry with large quantities of waste heat to recover"

Jan 1, 2012

By Tong Deng

Clean processing of copper converter slags for reclaiming cobalt and copper could be a challenge. An innovative and environmentally benign approach for recovering metal values from such a slag was developed in the present work. Curing the slag with sulfuric acid, without re-smelting or roasting as currently practiced in the industry, made it amenable to leaching, and more than 95% of the cobalt and up to 90% of the copper was extracted, together with iron, by water leaching, leaving silica behind in a residue. Copper in the leach liquor was recovered by cementation with iron, and the dissolved iron crystallized as ferrous sulfate monohydrate. Cobalt in the pregnant solution rich in iron was recovered by either cementation or sulfide precipitation. Chemical and mineralogical characterization of the slag and its products were examined and compared to determine the nature of the changes occurring during curing and leaching. Operating variables were also investigated and optimized.

Jan 1, 2003

By M. D. Crites

As part of a multi-year program for assessing the viability of chrome-free refractories in copper smelting, converting and refining furnaces, dynamic corrosion tests have been conducted on a series of refractories from the magnesia-alumina system, using a ferrous silicate slag. The corrosion rates of the test refractories are compared with those of a reference mag-chrome brick, and recommendations are made for more in-depth evaluations of the more corrosion-resistant materials.

Jan 1, 1999

By Mick O'Meara

Metal Organic Chemical Vapour Deposition (MOCVD) is used in the production of computer circuit boards and metal shapes in nickel, gold, copper, cobalt, etc. All varieties of .MOCVD use the decomposition of a vapour of organometallic compounds to produce different forms of ultra-pure metals, or alloys. CVD Manufacturing's proprietary MOCVD process has been adapted and developed to produce commercially ultra-pure metal shapes, metal powders, and metal foams. Therefore, it is a purification process. The typical process has three steps. First, a volatile metal organic compound is produced from volumetrically contaminated metals, metal oxides, etc. Typical feed materials are metal powders, ores, concentrates, or a slurry of metals and contaminants. Secondly, the volatile. metal organic compound is purified by fractional distillation. Thirdly, the purified metal organic compound is decomposed into different forms of ultra-pure metals, such as net shapes, powders, or metal foams. A mixture of metals can be purified either by the selective production of volatile materials, or a separation can be achieved during the second step, in the fractional distillation stage. The purification and recycling of metals by the MOCVD process will be discussed, particularly with regard to nickel, aluminum, gold, the platinum group and other metals.

Jan 1, 2000

By L. Lewczuk

A detailed mineralogical and liberation study was performed on the iron ore mill products from the Scully concentrator of Wabush Mines, Newfoundland. Automated image analysis techniques were applied to deter-mine grain size distribution and liberation of all mineral components of the ore. As a result of the study it was indicated that iron recovery can be improved and the Mn minerals reduced in the iron ore concentrate by (a) increasing spiral middlings, (b) regrinding the middlings, and (c) separating the Mn minerals from the iron minerals in the reground middlings.

Jan 1, 1988

By E. M. Weenink

One of the new direct smelting technologies for the production of lead from sulfide concentrates that has reached the commercial stage is the Outokumpu lead flash/electric furnace ?smelting process. Using data from pilot plant test work, energy and mass balances for a commercial plant were initially calculated by hand. To optimize process conditions, a large number of such balances had to be generated and a computer program using Lotus 123 was developed which provided an excellent opportunity for computer simulation. Operating parameters can be calculated by iteration using input values for feed composition, feed rate, smelting temperature, and lead content of the slag'" The output is presented by means of various views of the appropriate process steps, or in 68 different graphs.

Jan 1, 1990

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By E. B. Zanelato

The process of casting metals and alloys occurs through the fusion of this metal and its subsequent casting into a mold with the dimensions and geometry close to the final piece. Most foundries use sand casting molds for making you. This work aims to characterize and evaluate the foundry sand to allow its use in segments of Civil Engineering, creating a viable destination for a residue is that discarded. The following characterization tests were performer: particle size, chemical analysis, X-ray Diffraction and Density Real grain. For the execution of the test specimens was used to 1:3 cement and sand, and the incorporation of 10% and 20% of the total mass replacing the sand, and the trace reference. The results show that best results in compression and bending tests were obtained by replacing 10 % of common sand for sand casting.

Jan 1, 2015

By W. Hoffelner

Plasma technology has become increasingly important for the treatment of several types of waste (toxic, nuclear, metal-bearing scrap). Plasma furnaces combine the advantages of a closed hearth process with a very versatile (several plasma gases can be employed) and effective heat source. It can be successfully used for recovery of metals with subsequent purification and/or vitrification of residuals from drosses or filter dusts.

Jan 1, 1994

By Kazuyoshi Shimakage, Shinji Hirai, Kenji Wada

"An amorphous zirconium oxide coating was prepared by the sol-gel process using zirconium tetra-n-butoxide on the surface of aluminum to improve the corrosion resistance to salt, acid and alkaline attacks. The coating films formed on the smooth aluminum substrates under UV-irradiation indicated an excellent corrosion resistance for salt, acid and alkaline attack tests. For example, the corroded area of coating film in salt attack test for 3600ks in the order of sol-gel coating· film< chromate film <boehmite film, and the sol-gel coating film had the best corrosion resistance. The coating film prepared on the coarse aluminum substrate by a boiling treatment after heat treatment at 573K also had greater corrosion resistance, and a water-avid surface appeared a contact angle of approximately 3°.IntroductionAs given in a previous paper1; a composite film consisting of a porous layer of anodically grown aluminum oxide filled with amorphous zirconium oxide and an amorphous zirconium oxide coating layer deposited thereon via the sol-gel process utilizing the dip-coating technique, was prepared to improve the alkaline corrosion resistance of aluminum. The alkaline corrosion resistance of these composite films was increased in the range of 24 to 50 times those of conventional anodic oxide films anodized in sulfuric acid. As a result, it was proved that heat treatment at 573K after dip-coating was an important process to .remove organic component from gel film and to accelerate the densification of coating layer. Furthermore, the effect of ultraviolet (UV) irradiation at ambient temperature on the densification of coating layer was also examined to lower the heat-treatment temperature2.Then, a sol-gel film prepared by UV irradiation at ambient temperature indicated that alkaline corrosion resistance of aluminum was superior in the range of 2.4 times to 2. 6 times that of the conventional composite film heated at 573K."

Jan 1, 2000

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By Merete Tangstad, Lars Klemet Jakobsson

"Slag refining is a promising refining method for boron removal from silicon as a part of a metallurgical route for production of silicon for solar cells. There is, however, limited data on the distribution of impurity elements between silicon and different types of slags. In the present study, the distribution of boron and calcium between silicon and slag were determined at 1600 °C for calcium silicate slags with a CaO/SiC>2 ratio between 0.65 and 1.3. An almost horizontal linear trend was found for the distribution of boron between silicon and slag, and the borate capacity was found to follow the relationln(CB0, ) = 30.8 + 2.96-V (1)where V\s the CaO/SiCh mass ratio within the range of the experiments.IntroductionSolar grade silicon feedstock contributes significantly to the total cost and energy required to make crystalline silicon solar cells. A less expensive and less energy requiring method of solar grade silicon production is therefore needed in order to make crystalline silicon solar cells more viable as an energy source. Silicon is an abundant element and the manufacturing cost of solar grade silicon is therefore mainly determined by costs related to purification of metallurgical grade silicon. The Siemens process is the most common process today, but it is an expensive and highly energy requiring process that gives silicon with a higher purity than is needed for crystalline silicon solar cells. A cheaper and less energy requiring method for production of solar grade silicon can either be achieved by modifying the Siemens process or by using a new production method. Purification of metallurgical grade silicon through a metallurgical route is a promising method that is already in use industrially. It has however proven to be hard to lower the boron content to 0.3 mg/kg or less, which is the requirement for most p-type crystalline silicon solar cell manufacturers. Slag refining is seen as one of the most promising approaches that can be used to bring down the boron content to the required level, but there is not much data on how boron is distributed between silicon and binary calcium silicate slags [1-4]. The distribution of boron between silicon and calcium silicate slags at 1600 °C has been studied in this work, and the obtained data has been used to calculate the borate capacity of binary calcium silicate slags."

Jan 1, 2012

By Jinrong Zhang

Major components of soil were tested for their ability to attenuate cyanide. Feldspar, kaolinite, plagioclase and bauxite are found to degrade cyanide at an appreciable amount mainly through adsorption. A soil near a mining site in northern Nevada was studied in detail using a tall column. Many species of cyanide were anlyzed to determine the mechanisms of the reactions of cyanide with soil. Volatilization, adsorption, oxidation, precipitation and complexing were quantitatively identified, being 5 to 10, 11.7, 4.2, 7.3 and 4 per cent of the total cyanide added, respectively. It is found that the oxidation of cyanide to cyanate is due to the catalytic effect of nickel and copper leached from the soil. Precipitation of metal-cyanide complexes occurred at low pH values.

Jan 1, 1991

By Norimasa Yamasaki, Masao Kurosaki

"The effects of plating conditions on the crystal orientation of electrodeposited zinc were investigated by varying elecyrolyte flow rate and current density. Precipitation of the Zn (00 • 2) basal plane is promoted at lower current density and higher flow velocity. Effect of the flow velocity on the mass transport was evaluated based on the polarization measurement in which Cu was used as the tracer. As a result, it has been clarified that the crystal orientation of electrodeposited zinc can be uniquely arranged by the overvoltage (iU0.5) that can be simply calculated by considering -the current density and boundary layer thickness. At the same time, the electrode potential during electrodeposition that can be calculated by using a model based on the competitive reactions of hydrogen reduction 'and zinc reduction exhibits an extremely good correlation with the crystal orientation of electrodeposited zinc.Introduction Electrogalvanized steel sheet has better surface properties than hot-dip galvanized steel sheet, and is used in home electric appliance and automobile applications. Factors such as crystal morphology, crystal orientation and surface roughness have a large influence on its appliance, formability and corrosion resistance [1-3].Electrolysis, condition, bath composition and alloying elements are reported as factors that affect the crystal orientation of the electrogalvanized coating. Factors that can be controlled on time in the production site are electrolysis condition that-is current density and plating solution flow velocity.Some studies[4-6] report that the crystal- orientation of the Zn(00 • 2) plane is increased by promoting, the mass transfer of zinc ions in the plating solution or decreasing the concentration overvoltage, but did not investigate in detail the plating solution flow conditions in the plating cell nor quantitatively determine the effects of both current density and plating solution flow conditions on the crystal orientation of ' electrodeposited zinc."

Jan 1, 2000