Search Documents

By S. S. Rowland

Good afternoon, ladies and gentlemen. It is a pleasure, for several reasons, to be here at this 13th International Conference on Ground Control in Mining. Of course it's always a pleasure to be able to see and reacquaint myself with many long-time friends; but it's also a pleasure, or 1 should say worthwhile, because I take something back with me, some knowledge about mining that lets me do my job better and more safely. if I can do that, I've accomplished my purpose in being at a conference such as this. This conference is a little different, though. I have to earn my stay. I have to earn it by telling you a story; a story about mining through a mile of rock to get from one coal seam to the same seam on the other side of an ancient river channel; a story about mine personnel taking over the job from a contractor; a story about having to mine through two faults after the hard part was supposed to be over, but, most importantly, it's a story about how it was accomplished successfully and safely by a group of ordinary coal miners possessed with determination, belief in themselves, and a "can do" attitude. If you can take any part of my story and use it to do your job better and more safely, then I will have accomplished my purpose in being here today. Kerr-McGee Coal Corporation's Galatia Mine is located in Southern Illinois near the town of Harrisburg in Saline County, about 350 miles south of Chicago and 120 miles southeast of St. Louis. Construction of the mine began in 1982, and the first coal was shipped in 1984 from the Harrisburg No. 5 Seam, 550' below the surface. Mining began in the Herrin No. 6 Seam, 100' above the No. 5 Seam, on April 1, 1985. Mining in both seams began by using the room-and-pillar method. In 1989, the No. 6 Seam was converted to longwall mining, as was the No. 5 Seam in 1992. Today, all mining is done by the longwall method except for the required development work, which is performed by continuous miners. A heavy-media preparation plant with a 4.2 million-ton annual clean-coal capacity processes the coal. By the end of 1994, with annual production now exceeding 4 million tons, we will have shipped over 30 million tons of steam and metallurgical coal throughout the United States and the world. Most of the coal has been used as the primary source of fuel to generate electricity for the city of St. Louis. The No. 5 Seam coal can be used as a semi-soft coking coal or as a high-Btu, relatively low-sulfur steam coal. Its use allows utilities to comply with Phase I of the Clean Air Act Amendments of 1990 without installing flue gas desulfurization units or blending with other coals. The Herrin No. 6 Seam is a high-Btu, medium-sulfur steam coal that requires blending to meet Phase I requirements. Because the No, 6 Seam coal does not meet the Clean Air Act Amendments' Phase I compliance standards, we were forced to cease mining operations in the No. 6 Seam, leaving 170,000,000 tons of minable coal in the ground. Last month the Galatia Mine became a single-seam operation mining the Harrisburg No. 5 Seam only. The Clean Air Act Amendments of 1990 and the resultant S02 emission limitations on electrical power generation plants effectively eliminate, beginning in 1995, the near-term potential for profitable mining of the Galatia Mine's high sulfur Herrin No. 6 Seam coal. Because of the Clean Air Act Amendments, it is virtually impossible to market high-sulfur coals like the No. 6 coal unless the mine location and mining conditions enable greatly depressed sales prices to cover costs. We, along with the majority of

Jan 1, 1994

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By P. Gaskell

The paper examines the development of rock movement between a longwall extraction horizon and the surface for a fully caved mining situation. Physical modelling has been used to examine the mechanics of ground movement and the propagation of fractures around the longwall working. The paper discusses dimensional analysis, model construction and measurement technique and data processing of the results into effective graphical forms for further study.

Jan 1, 1988

By T. M. Tharp

Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a MohrCoulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size.A continuous stepped failure surface produced by propagation of preexisting joints may develop at lower shear stress than pre¬dicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

By Robert W. Bruhn

An investigation was male of ground response to pillar retreat mining in a 1.7 meter thick seam at 108 meter depth at a site in northern West Virginia. This paper describes mining-related stress changes and movements at nine level, displacements within the overburden, ground surface subsidence and groundwater level variations. Subsidence approached 40 per cent of the nine height ad continued more than a year after mining. Water levels declined la certain deep-lying strata.

Jan 1, 1984

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

One of the problems associated with the maintenance of roadways in underground coal mines is that of dealing with roadway closure. Sidewall weakening technique is based on the transference of the high stress zone further away from the vicinity of roadway. This transferral is carried out by weakening parts of sidewalls of roadway by cut- ting slot, drilling a series of parallel holes or blasting during development stage. In the paper, the effect of sidewall weakening on the stability of roadway is studied by finite element analysis and field experiment. The finite element analysis shows that sidewall weakening can control the development of yield zone around a roadway, improving the stability of roadway. It is also shown that if in- situ horizontal stress is lower or higher than the in-situ vertical stress, it is difficult to obtain roadway stability by sidewall weakening. The field experiment shows that roadway closure can be controlled by sidewall weakening with blasting.

Jan 1, 1990

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By Ry Stone

To maintain longwall continuity, NRE Wongawilli Colliery extracted the approximately 20-year-old Thompson Mains and in doing so, 20 roadways were holed into during longwall retreat. The orientation of these roadways with regard to the longwall face varied between (i) a parallel alignment where the entire roadway was simultaneously subjected to a significant increase in vertical stress on holing and (ii) a more favorable high angle of alignment, meaning that only a portion of the roadway was subjected to an increase in vertical stress on holing. In addition, the longwall holed into and was recovered in one of the existing roadways. The geotechnical environment presented several additional challenges during longwall retreat. The orientation of the stress field resulted in a major horizontal stress notch on the maingate and an elevation in the major horizontal stress in front of the longwall face during the retreat up to an adjacent goaf edge. The presence of geological structure zones also resulted in both swings in the major horizontal stress direction and increased levels of roof deformation. The gate road support designs were based on commonly accepted strata management techniques and principles. The support designs in the hole-through roadways were based on empirical design models generated from (i) aconceptual geomechanical model of pre-driven hole-throughand recovery roads and (ii) a worldwide database on pre-driven hole-throughand recovery roads. Imperative to the success of extracting the panel was a sitespecific strata management process. In this regard, consideration was given to the following: roof displacement monitoring in the gate roads (in particular, Longwall (LW) Acceleration Position), roof-to-floor convergence monitoring in the hole-through roadways, the ability of the mine to limit downtime prior to and during holing by utilizing an Authority to Mine (ATM) type process, and the use of Trigger Action Response Plans (TARP).

Jan 1, 2012

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By Guangyi Sun

Wall rock classification method for coal mine support is the main factor affecting mine support. It is greatly affected by the combined effect of randomness, fuzziness and human being's incomplete knowledge. There are several coal rock classification methods. Using different rock classification methods the same engineering rock mass can be classified into different classification leading to different construction practices.

Jan 1, 2005

By Peter Zhang

Pumpable cribs are being increasingly used in longwall tailgate entries and bleeders for roof support under abutment pressure. Their high peak capacity and confinement-controlled yield characteristics from reinforced-bags make them relatively safe and reliable standing supports for highly productive longwall panels. The pumpability of crib material over a long distance from the surface greatly reduces material handling and makes the underground installation more efficient and flexible. However, the performance of pumpable cribs is dependent upon crib properties, crib pattern, quality of installation, and geological and mining conditions. For proper crib selection and safe support design, it is critical to understand the basic technical requirements and performance of pumpable cribs in longwall tailgate entries and bleeders. Based on more than 10 years of experience using pumpable cribs for longwall standing support, the requirements and performance of pumpable cribs in longwall tailgate entries and bleeders under different mining conditions are presented. Experience shows that the load-displacement curve from full-scale lab testing is a good indicator of pumpable crib suitability for certain applications. Crib peak capacity, stiffness, and residual characteristics define its applicability to certain gate entries and bleeders under different cover depth. Crib pattern and spacing can be determined by abutment pressure level, roof, floor, and rib conditions, local roof stability, and ventilation requirements. To achieve proper in-situ performance, quality control of crib installation is also important.

Jan 1, 2012

In this paper, the authors attempt to apply a simplified non-homogeneous void diffusion model (NHVDM) to predict surface subsidence for longwall mining in Illinois. A generalized error function subsidence profile is derived from this model. The model validation indicates that the NHVDM approach appears to fit the observed subsidence data as well or better than the error and the trigonometric functions, particularly around the trough edge areas.

Jan 1, 1990

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998