Search Documents

By R. J. Roman

Controlled and uniform distribution of the leach solution to a heap is of primary importance to achieving the desired rate of metal recovery and PLS grade from the heap. The step used to engineer the irrigation system are the same whether drips, wobblers or sprinklers are to be used. The mining rate, leach cycle time and heap height influence the heap cell size which along with the irrigation method selected controls the design of the irrigation system. The steps in the design procedure are explained as are the advantages and disadvantages of each irrigation method.

Jan 1, 1996

By A. De Daio, D. W. Fuerstenau, P. C. Kapur

Because of its pronounced tendency to undergo visco-plastic flow, coal ground in the energy- efficient high-pressure roll mill invariably comes out as a briquetted product which must be disintegrated in a conventional type of grinding device such as the ball mill. The aggregates comprise comminuted coal particles that are apparently extensively cracked and weakened during passage of the coal through the high-pressure rolls. Their deaggregation in a ball mill in the second stage is accompanied by further grinding of the coal with a relatively small expenditure of energy. Thus in spite of energy dissipation in briquetting in the roll mill and in disintegrating the briquettes in the ball mill, significant energy savings are possible in the fine grinding of coal in a two-stage serial grinding mode, as compared to ball mill grinding alone. It has been determined that for the best results the energy invested in the two grinding stages must be apportioned in an optimal manner, the energy consumption in the ball milling step is comparable to, even in excess of, the energy spent in the high- pressure roll mill; and 20 to 50 percent energy savings might be possible in grinding coal to minus 200-mesh size by this two-step process, as compared to conventional milling.

Jan 1, 1995

By J. Harrison Daniel

Increasing mechanization of underground mining operations throughout the years has reduced the dependency on large, concentrated working forces. Fewer workers in scattered locations, coupled with the versatility of diesel equipment to load and haul personnel, supplies, and mineral ore, has made diesel equipment attractive in mine feasibility and design studies. The use of the mobile equipment along with higher production or "bulk" mining methods provides for more efficient mineral extraction systems. These systems are expected to become more widespread until long-term research provides a further evolution to more complete automation of underground mining. The U.S. Department of the Interior, Bureau of Mines, has been conducting research to reduce the health and safety hazards posed by increasing use of diesel equipment and the higher power ratings being proposed. The goal is to provide for safe and efficient use of the equipment. The National Institute for Occupational Safety and Health has recommended that diesel exhaust be regarded as a potential occupational carcinogen adding importance to the Bureau's research program. The paper describes advances in engine design, the use of diesels in mining operations, and significant health and safety research accomplishments of the Bureau of Mines. These accomplishments will help assure that diesel equipment remains an option for determining the most efficient system to mine an ore body.

Jan 1, 1989

By Mario Eduardo Rossi

The Universal Kriging (UK) and the Ordinary Kriging (OK) systems of equations are variations of the well-known system of Normal Equations. They differ only by the number of constraints present in the system. The dual version of these sytems enables one to interpret kriging as the fitting, of an interpolation surface, whose components are a series of variogram functions plus a polynomial trend model. This trend model should account for any systematic decrease or increase of the variable over the study area. It is shown that modeling the trend is useful only when the locations being estimated are beyond the range of influence of neighboring data (extrapolation cases). A case study based on a public-domain coal data set is presented. The variable described (seam thickness) shows an actual trend of increasing data values towards the NW corner of the region considered. UK and OK are used to estimate coal thickness at locations within sample data range (interpolation cases). The UK algorithm that includes a model for the trend does not improve the estimation when compared to the simpler OK algorithm with no trend model. Thus, in interpolation situations, the simpler OK algorithm is recommended.

Jan 1, 1989

By Michael J. Howes

The nature of business in a free enterprise system is to maximise the return on an investment i.e. to maximise the wealth of the shareholders. This is normally achieved within constraints dictated by many agencies, one of which is the health and welfare of the employees. In the mining industry considerable effort has been expended in improvements in this field, however, the major problem still confronting the practicing ventilation or environmental engineer is the determination of what standards he should design for, which satisfy both the economic and health requirement s. Normally the basic health requirements are satisfied by the minimum standards defined in regulations and codes of practice. These are, however, based on an acceptance of a certain risk or lower production potential. A prime function of the ventilation engineer is therefore to financially justify and implement improvements to both standards and systems. The main purpose of this paper is to examine the basis and techniques of providing this financial justification. Changes in existing methods to achieve the same standards but at lower costs are also covered.

Jan 1, 1980

By J. Herbst, H. W. Kropholler, L. A. Cramer, E. T. Woodburn, J. C. A. Greene, G. Poling

A generalized mathematical structure is proposed whereby internal species mass flows within a flotation network are defined uniquely by a matrix of enhancement factors. An element of the enhancement factor matrix is defined as the ratio of the mass flow of that species leaving a given cell in the concentrate to the species mass flow leaving the same cell in the tailings. To predict the enhancement factors, knowledge of flotation kinetics effects is required. Recently experimental data has become available relating to the performance of industrial flotation circuits which indicate that the discrete or discrete-distributed kinetic schemes are capable of reasonably effective simulations. These simulations show the importance of including froth effects. The prediction of performance of networks from small-scale batch tests on flotation streams shows that the model for the froth phase used in the simulations does not scale-up well and that aeration effects are also difficult to predict. The network analysis should be useful in differential flotation of complex ores and it is disappointing in this context that little information on the kinetics of activation and depression is available.

Jan 1, 1976

By Jan M. Mutmansky

While production scheduling for both surface and underground mining operations is similar in nature, a rather large array of techniques is applied in solving such planning problems. The techniques consist of both rigid operations research (OR) methods and practical procedures which are not mathematically based. In the following sections, a short summary of some of the techniques that are applicable to production scheduling problems in mineral operations is presented. The techniques discussed are: linear programming, integer programming, dynamic programming, graph and network theory, simulation, and heuristic methods. For an in-depth comprehension of these techniques, the reader is referred to any of the available textbooks on these subjects. One or more references will be listed for each topic to provide a starting point.

Jan 1, 1979

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ?Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions became the post-event conditions. ?Search for evidence that either denies or supports the various hypotheses. ?Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By N. Piret, B. Shoukry, S. Buntenbach

Traditional or artisanal goldmining, also known as small scale goldmining, has a strong and probably a negative environmental impact. The processing methods applied are very frequently a source of severe pollution due to the emissions of mercury by the extraction of gold by means of amalgamation as well as the emissions of cyanide through cyanide leaching of gold bearing ores. The emissions find their way into the environment and contaminate soils, sediments, water and atmosphere. Abnormal concentrations of mercury and cyanides in waterways are known to occur year after year destroying irreplaceable regions of the world. Mercury and cyanide compounds are highly toxic and may directly create permanent damage to the whole ecosystem. Existing methods for recycling of mercury and for decontamination of mercury and cyanide contaminated tailings are not customary applied in small scale mining and are ineffective as well. Based on investigations of traditional and small size goldmining, this paper presents: -processing methods of gold and discarded tailings under consideration of environmental protection; -figures on actual situation; -recommendations for equipment; -some decontamination methods for mercury and residual cyanide. Mineral Processing methods in traditional gold mining Gold is usually existing in its ores as the metal alloyed with metallic silver and perhaps copper. The element may occur in the form of: -native gold -inclusions also of microns or submicroscopic size metal sulfides (auriferous) such as pyrite, pyrrhotite, stibnite, arsenopyrite and galena -combined as telluride or sulphotelluride. The separation process selected depends on whether the gold can be freed from its unfavorable associations (e.g. gangue) at a sufficiently coarse grain-size, or whether it is carried in a heavy sulfide which can be freed similarly. The usual practice is to concentrate the goldbearing mineral at a relatively coarse grain-size and to regrind the ore if necessary. The gold content is concentrated by secondary or tertiary gravital methods or is extracted by chemical methods (amalgamation, cyanidation etc.) Gold, even when of fine grain-size, settle readily due to its high specific gravity from pulps in which the main gangue mineral is quartz or silicates. Amalgamation is the process of separating gold and silver from their associated minerals by binding (entrapping) them into a mixture with mercury. The cyanide process is applied to separate gold or gold-bearing compounds by dissolution from the finely ground ore (CIP, CIL, RIP), or as heap leaching. The dissolved gold is separated from the solids and the metal-rich or pregnant solution is then treated to recover its gold. Gold is also recovered by flotation methods. This process is widely used in treating base metal ores and in separating various sulfide components of ores, as well as in removing the barren gangue. The gold usually associates with a specific product in a sequence of flotation operations and is recovered subsequently in the smelting of the sulfide concentrates and refining of the metallic products, or by cyanidation of the roasted concentrates. Froth-flotation can be applied to separate gold and sulfide minerals from a finely ground pulp. The Amalgamation Process Amalgamation is the main method for the recovery of gold in traditional mining and is applied for the extraction of gold from placers as well as primary ores. The mineral technology used depends on the nature of ore deposits. In winning gold from solid ore, the matrix of minerals and rocks must be crushed and ground to sufficient fineness to liberate the gold. The liberated gold could be treated similar as free gold from placers. Gold is mainly separated from the valueless gangue (barren rock) by utilizing the difference between the density of the impure native metal (density about 16-19) and the gangue (density about 2.5). In simple operations the material is carried by a stream of water down a sluice generally equipped with small transverse barriers (riffles) against which the gold collects. The riffled sluice is the principal device used by artisanal gold miners. Nowadays, spirals as well as centrifuges, such as Knelson separator or Falcon separator, are occasionally applied for gold recovery. Gold may also be recovered from the pulp, by passing it over corduroycovered tables that catch the heavier particles - a method maybe as ancient as gold mining itself. In history, sheep skins were used to catch gold particles in this manner. Furtheron, gravity separation of gold is practiced on jigs, hydraulic traps, shaking tables and

Jan 1, 1995

By Jeffery H. Stricklin

Jim Walter Resources operates five underground coal mines with longwall faces in operation in four of the mines. Due to high air velocities (1000-1200 fpm) needed for methane control together with the friability of the coal, dust control on JWR longwalls offers unique challenges. We have tested many innovative measures to reduce respirable dust concentrations on longwalls with varying degrees of success. These measures include the "shearer clearer" system, different drum water spray configurations, sprays on the longwall belt, stageloader and crusher sprays, wetting agents in the spray water system, and homotropal ventilation. Water infusion of deactivated horizontal methane drainage holes in longwall panels is now being evaluated. A study was completed in November 1986 where water was infused into two horizontal de-gas holes. Personal gravimetric samplers were used to measure respirable dust concentrations and showed a significant reduction in the infused zone. A more in depth study will be conducted. This paper will describe the dust control measures presently used on JWR longwalls, give the results of past studies, and discuss new methods proposed to control longwall dust.

Jan 1, 1987

By J. T. Crawford

A comprehensive strategic-planning model was developed for the phosphate strip-mining and chemical operations at White Springs, FL. The computerized model covers orebody modeling, production simulation and financial analysis. The model has several innovative features, including the use of NPV techniques in orebody block economics, the adaptation of the floating-cone method to a floating template for generating dragline mining units automatically, the use of interactive graphics for designing mining units, and the use of a dragline move economics algorithm for the automatic scheduling of mining-unit assignments and moves. The simulation of chemical-plant production uses linear programming and concentrate inventory levels to control mine-operating schedules.

Jan 1, 1999

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By William G. Fischer

Equations developed by an early researcher in subsidence, F. Martos of Budapest, Hungary, have been slightly modified to produce effective equations for predicting the time-dependent nature of Green River trona mine subsidence. Following the initial study, a survey was run to check the results twenty years after mining of the area had been completed. The final results were within a few centimeters of the value that had been projected. Mining conditions in the Green River area are ideal for this sort of study with trough type subsidence being the surface manifestation of high extraction underground room and pillar caving operations.

Jan 1, 1986

By S. R. Clifford

Organic contaminants can be removed from river sediment using conventional flotation methods. Organic contamination in sediments is one of the most significant pollution problems facing the Great Lakes region. Using conventional flotation, the majority of the organic contamination can be collected in a concentrate, leaving a "clean" tailings. This provides a cost savings by reducing the amount of material requiring further treatment. The concentrate can then undergo additional flotation stages, or other contamination removal procedures, to further remove the organic contaminants.

Jan 1, 1994

By M. E. Rossi

Reconciliation of long-term, block-model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term, block-model reserves against a grade control model (a model based on blast holes or production data). In this article, this is called an Fl factor for tonnages, grade and ounces. This reconciliation should also be done by comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator, such as kriging, will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMUs to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. Therefore, the grade-tonnage predictions based on blastholes also need to be assessed - considering unplanned dilution and the errors of estimation of the grade control model. This article focuses on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer. It yields several possible minable reserves and several possible minable tonnages and grades, per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation and the planned and unplanned dilution. It also carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The estimation of recoverable reserves revolves around estimating the block distribution of metal grades from the drill hole information available, typically composites of a fixed length. Ideally, this estimation should accurately predict the ore sent to the processing facilities of an operation. Here are some definitions used in this article: ? Recoverable reserves are those where an attempt has been made to estimate the actual distribution of grades (usually by a block model) that would be found in the ground at the time of mining, relative to the mine equipment size and other operational characteristics of the mine SMU. In particular, it incorporates the effect of internal dilution for each block how the grade distribution changes in variability when comparing a composite grade distribution to the "mining unit" grade distribution. In geostatistical jargon, this is known as "change of support effect," or volume-variance effect. ? Minable reserves are those recoverable reserves defined by a mine plan. In an open-pit scenario, they would incorporate pit optimization in addition to the sequencing and scheduling of production through mine life. ? All other block model estimates from drill hole data that do not explicitly attempt to estimate or measure the volume-variance effect are called in situ. It can be argued that these models may be inappropriate tools for predicting the grade-tonnage curve of the material to be sent for processing (minable reserves). The purpose of estimating recoverable reserves can be thought of as estimating the appropriate amount of dilution that should be incorporated into the model so that it adequately predicts (long-term and on average) the grade-tonnage curve of the ore sent to the processing facilities (mean grades and ton-

Jan 1, 1999

By R. C. Jr. Babcock, V. S. Znamensky

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd. in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 km. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fiber in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd., of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This chapter presents the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits are outlined. Subsequent work by other companies is mentioned, but not de- scribed in detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd. who have been involved in the project. In particular, thanks go to Ramon Farmer, N.G. Corner, and A.W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this chapter are solely that of the author and result from his involvement in the discovery of the deposits and management of the exploration program. REGIONAL SETTING Ultramafic rocks on the South Island of New Zealand are thought to be Permian in age and occur between crystaIline and metamorphic continental rocks of Precambrian through Cretaceous age in the west, are thought to have once been part of the Antarctic subcontinent, and the extensive geosynclinal graywacke deposits of the Mesozoic New Zealand geosyncline in the east. They consist of the Dun Mountain ultramafics, a 130 km long segment of ultramafic rocks located at the north end of the South Island, and the Red Mountain ul- tramafics that occur in a zone 200 km long in the south half of the South Island as shown in Fig. 1. These two belts, once contiguous, have been offset a distance of 560 km by the still active Al- pine fault, which is analogous in character and offset to the San Andreas fault of the United States. The ultramafic rocks occur within a sequence of Permotriassic volcanic and sedimentary rocks that probably formed at the eastern margin of the continental plate. The ultramafics appear to be tectonically emplaced between Permian lithologies in the Dun Mountain belt (Coleman, 1966), and at the base of or between Permian volcanics and sediments in the Red Mountain belt. The Permotriassic ultramafic volcanic sequence of the Red Mountain ultramafic belt appears to be a typical ophiolite sequence. Ultramafic rocks, mixed mafic intrusive rocks and volcanics, volcanic rocks, and volcanoclastic sediments occur in apparent superposition from east to west in the area of Red Mountain. Farther south, ultramafic rocks are associated with basaltic volcanic rocks and some sediments, and still farther south are emplaced entirely in sediments. These structural compIications of the normal ophiolite sequence have resulted from the coincidence of Permian subduction, early Mesozoic extension and sedimentation, and Cretaceous subduction along the same plate margin (Landis and Bishop, 1972). The general geology in the area of the Red

Jan 1, 1986

By Osvaldo Bascur

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. This results in significant deterioration in the ability to maintain a "smart" operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. This paper describes the use of Internet technologies with plant data. Examples are drawn from existing industrial sites. Users must project where this technology will lead - standing still is the most dangerous philosophy and the only one guaranteed to be obsolete. These examples show the way to leverage existing workers with information technology.

Jan 1, 2000

By Richard L. Coleman

El trabajo de ensayo metalúrgico para desarrollar un flujograma es el que ahora describimos, comenzando con una información experimentada requerida en todo momento hasta llegar a un esquema final de flujo de un proceso. Tanto las pruebas de laboratorio como de planta piloto son revisadas adecuadamente sobre las experiencias anteriores.

Jan 1, 1982

By R. F. McFarlin, H. E. El-Shall

Since its inception, the Institute of Phosphate Research has examined every promising proposal in order to find an economical, practical and environmentally sound method of dewatering phosphatic clays. The in-house development of the FIPR/DIPR process (DIPR = Dewatering Instantaneously with Pulp Recycle) would appear to answer that quest. When small amounts of fibrous materials are mixed with clay slurries and flocculent, rapid dewatering occurs. Clay solids contents of 20 to 25% can be attained by simply rolling the clay mass down an inclined screen. Higher solids (>40%) are reached by physically pressing the cake; e.g., with a belt press. Because mechanical pressing devices are too expensive for phosphatic clay treatment, FIPR has developed the "sandwich" method of simultaneously dewatering the phosphatic clays and reclaiming the mine cut, as well as a second alternate, the "median strip" proposal. Economic projections of these bench-scale alternates suggest that the FIPR/DIPR process should be no more costly than present practice, when credit is given for the simultaneous reclamation accomplished.

Jan 1, 1993

By Charles E. Glass

As partial implementation of the Surface Mining Control and Reclamation Act of 1977, the Office of Surface Mining (OSM), Department of Interior, has requested each state to inventory hazardous abandoned mining areas within their boundaries. Primary interest is in such areas .as unstable waste-banks, subsidence and slumping, contamination of water supplies, and preservation of overall aesthetic qualities through reclamation. In addition to the concern expressed for abandoned mining areas, the legislation requires a complete inspection of operating mines quarterly and a partial inspection monthly. In Arizona copper has been mined for over 100 years and coal and uranium mining promises to expand in future years. The OSM requirement for a waste inventory and frequent monitoring of Arizona's large, widely spaced mines places a severe demand on limited personnel and operating budgets. Remote sensing by satellite provides an attractive and effective approach to aid the inventory and monitoring requirements of the OSM legislation.

Jan 1, 1979