Search Documents

By William W. Magnus

The Eastern Magnesia Talc Company has always had the problem of adequate storage at its various mines and mills of not only crude ore and finished product but also material in process. An opportunity arose a couple of years ago with the decision to build a new mill at West Windsor, Vermont, (Figure 1) to come as close to providing adequate space for ore and the ground talc in the new plant as money and judgement would allow. Since our engineering staff did not have the time to design and engineer the new facility, an architectural firm with complete engineering staff was retained. Our original thought was to contract all phases of the construction and installation, however, and I think this is a most important point for any small firm such as ours, we found that with good supervision we, as the contractor, could do the job faster and at a lower cost than the construction firms that bid on the work. For some 50 odd years Italian talc has had a virtual monopoly in the body powder area of the cosmetic industry. Due to the purity, superior lubricity and whiteness, naturally occurring in the talc from Italy, no talc in the Western Hemisphere could capture any but a very small part of the market. When the Italian supply was cut off during World War II, the United States' largest consumer of this talc decided that it was time to develop a domestic source of a satisfactory replacement.

Jan 1, 1965

By Larry B. Bramlett

Regional radiometric, magnetic and geologic data point to Copper Mountain as an area of general uranium favorability. Sub-regional radiometric and magnetic data direct interest to a specific section of an overthrust Precambrian granite. Detailed magnetic and resistivity surveys in this area show local targets of interest, one of which corresponds to Rocky Mountain Energy's North Canning deposit. On the basis of these data a second and previously untested target was drilled resulting in the intersection of uranium horizons similar to those at North Canning. This integrated geophysical approach can be used for uranium exploration in geologically similar areas.

Jan 1, 1979

By Richard Klimpel

A common problem in mineral processing and chemical engineering is the need to estimate flow rates and/or weight ratios involved with engineering operations for which it is inherently difficult to directly measure stream weights. Simple examples of this situation include stream separators (a classifier operating on a particle flow) and stream mixers (the mixing of new feed and circulating load in a ball mill circuit). Often in these types of operations, it is possible to sample the streams involved to get approximate component analyses (e.g. size distributions of solid streams, chemical composition of chemical streams). In this paper various formulae are developed which can be used to estimate stream flow rates or weight ratios given information on the stream components. The type and level of experimental error present in the stream component analyses does have an important bearing on the numerical values (and reliability) of the weight ratios calculated by the various formulae. A simple but theoretically sound method is shown for selecting appropriate estimation formulae for any given engineering operation. The derived formulae are applied to sets of experimental classification data for illustration purposes.

Jan 1, 1979

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

By R. J. Smith

Tar sand deposits in Utah represent more than 25 billion barrels of in-place bitumen, 96% of the known U.S. reserves. The technological development of a hot water processing strategy for the Canadian tar sands and the commercial Production of synthetic crude oil from this natural resource suggest that similar success may be possible for the utilization of Utah tar sands to provide our country with a new domestic source of synthetic crude oil. In this regard an active research program to develop a hot water processing strategy for Utah tar sands has been sustained at the University of Utah for the past five years. The hot water process for Utah tar sands differs significantly from that used for Canadian, tar sands due to the inherent differences in the respective bitumen viscosities and the nature of the bitumen-sand association. These differences have led to the identification of certain design criteria necessary to achieve satisfactory phase disengagement during digestion. (8,9) Subsequent flotation of the digested tar sand is a subject of current attention and is considered in this contribution for the Asphalt Ridge tar sand deposit. Although contact angle measurements of pure Asphalt Ridge bitumen indicate moderate hydrophobicity, air bubble attachment to the bitumen concentrate taken from a 37 liter flotation cell is not possible. This surprising result suggests that the flotation separation is dependent on air bubble entrapment rather than on attachment due to surface hydrophobicity. The occlusion of air bubbles in the bitumen is apparent from visual examination of the concentrate, especially at lower temperatures. It seems that a bitumen bubble agglomerate forms in the impeller region of the flotation cell, the effective density of which is such to allow the agglomerate to float to the surface. A factorial design of the major operating variables in the flotation separation indicated that the quality of separation was significantly dependent on the flotation temperature and to a lesser extent on the degree of agitation. For a flotation temperature of 77C recovery of 96.7 percent was realized at a grade of 61.0 percent bitumen. The improved separation at higher flotation temperatures was found to be due to the decrease in bitumen viscosity resulting in more effective rejection of coarse sand from the concentrate.

Jan 1, 1980

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960's. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By C. D. Atkinson

The past few years have seen a much greater concern about air pollution in this country. This concern has led to increased legislation restricting the discharge of many substances such as sulfur dioxide and particulate matter to the atmosphere. In the future, it is anticipated the present permissible emission levels will be lowered. Current and impending restrictions on the emission of sulfur dioxide have brought out the fact that there is a shortage of available low-sulfur fuel for power plants and industrial use which promises to have an economic impact on the nation's energy picture (1) The Pittsburg & Midway Coal Mining Co., under the sponsorship of the Office of Coal Research, has developed a process to produce a fuel capable of meeting the energy requirements of this nation (2) The process is called "The Pittsburg & Midway Solvent Refined Coal Process". The principle product from the process is Solvent Refined Coal which is an ashless, low-sulfur fuel with 16,000 BTU per pound regardless of the rank coal from which it is produced. The product can be burned as either a solid or a liquid fuel. The process appears to be economically more attractive than other methods of alleviating the pollution problems of this nation. In addition to reducing the air pollution caused by stack gases, the product produced is potentially useful as a source of electrode coke and electrode binder pitch, as a gas turbine fuel, in the production of metallurigical coke and pavement asphalt, and as the first step in the overall process to produce distillate fuels and pipeline gas (3).

Jan 1, 1973

By F. M. Stephens

This paper is to be presented at the annual meeting of the American institute of Mining and Metallurgical Engineers, San Francisco, February 1959. Permission is hereby given to publish with appropriate acknowledgements, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the authors, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1959

By V. Svalbonas

With the occurrences of serious mill structural failures on both ball and primary mills, the mining industry has entered the era of detailed fabrication specifications. Such specifications, however, have been developed as individual entities, often by people not related to the mill design function. Therefore, there has been no effort to relate mill failure or safety to the existence or elimination of specific fabrication flaws; that is, no cause-effect failure relationships have been developed. The omission of this step produces a specification which can be termed uneconomical at best. The present paper attempts to fill this void, by reviewing methods for design consideration of flawed structures, and describing experimental tests used to tie such data to a meaningful quality assurance program in fabrication.

Jan 1, 1985

By Dennis W. Leonard

Let us begin our discussion by looking at historical and current levels of sales of both natural and synthetic zeolites on a world-wide basis. Due to the understandable reluctance of some companies to disclose sales data, some estimation has been necessary regarding the tonnages and values shown in Table 1. We are confident, however, that they are within acceptable limits, especially the numbers referring to natural zeolite.

Jan 1, 1979

By Edward W. Long

The Density Separator is basically a hindered settling classifier with automatic control features that provide steady, sharp classification irrespective of extreme variations in dry tons per hour of feed solids up to the design maximum throughput for the particular material being treated. The size and capacities of commercially available units and operating data comprise the scope of the paper. Applications of the unit for other than classification are proposed, i.e. washing and desliming.

Jan 1, 1982

By Shane Yanagisawa

The Mineral Creek Diversion Project is at the Asarco Ray Mine Complex, about128 km (80 miles) east of Phoenix, Arizona. The new tunnel will intercept the waters of Mineral Creek about 2,134 m (7,000 ft) upstream from an existing tunnel. The 5.74 m(18.83 ft) hard rock TBM will break into the old tunnel about 2,162 m (7,090 ft) in from the old portal after mining 3,888 m (12,753 ft). The TBM will mine through a series of igneous and metamorphic formations including volcanic tuff, soft volcanic ash, massive diabase, fractured quartzite, and schist. The TBM will hole through into the existing 4.88 m (16 ft) dia. horseshoe tunnel where the TBM will be disassembled and removed from the tunnel.

Jan 1, 2001

By L. A. Bellows

The "Athabasca oil sands" of the McMurray formation in northeastern Alberta cover an area of about 21,000 square miles and contain the world's largest reserve of oil. Fort McMurray, a small town in the heart of the oil sands area, is about 235 air miles north- east of Edmonton. A railway serves the town but no year-round roads connect the town with the rest of Alberta. (Figure 1). The McMurray formation is of early Cretaceous age, deposited unconformably on a limestone surface of Devonian age. The sediments appear to have originated from the Canadian Shield to the east and were deposited in bays and deltas of large fresh water lakes. The lakes were later replaced by marine seas in which t the overlying Clearwater shale was deposited. (Figure 2).

Jan 1, 1963

By R. T. Swinderman

This paper discusses a series of tests designed to help answer the age old question: ?How much does the belt cleaner wear my belt?? The experimental set up and test method are described. The main variables are: belt cleaner blade materials, cleaning pressures, cleaning angles, belt speeds, and belt top cover grade. The bulk material used is a standard test-grade silica sand. The measured results include: blade mass loss, belt mass loss, and cleaning efficiency.

Jan 1, 2010

By B. W. Madsen

Experimental results obtained from large scale (7 tons), long-term (500 days) leaching of low tenor copper sulfide ores were interpreted by a geometric model involving the movement of a reaction zone through the ore fragments. The postulated leaching mechanism involved mixed kinetics and included diffusion of the reacting species through the host rock and a chemical reaction at the surface of the mineral particles. Ore properties which were considered were ore particle size and shape, grade of ore, and mineral content. Excellent agreement between the mixed kinetic model and the laboratory leaching results was obtained when minus ½ inch ore particles were not included in the leach. Also, a satisfactory prediction of copper recovery from plus ½ inch ore with a different particle size distribution was made; however, it was necessary to modify the shape factor in the model. Predictions of copper recovery from an ore sample which included the minus ½ -inch fine fraction and leaching for 460 days was 56.5 percent, and the recovery from leaching was 47.0 percent. The presence of fines caused channeling and uneven solution distribution and inhibited the leaching rate.

Jan 1, 1974

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By Robert W. Cope

"Mining began, in the Colstrip area in the 1920's by the Northern Pacific Railroad. The coal was used for steam locomotives until 1957, when the advent of diesel power made them obsolete. In 1959, Montana Power Company purchased the Northern Pacific properties including the mining equipment, coal leases and the town of Colstrip. Western Energy Company, a wholly owned subsidiary of Montana Power Company was formed in 1966 to manage the mining operations in Colstrip. The Rosebud Mine officially re-opened in 1968 to supply coal for Montana Power Company's J. E. Corette Plant In Billings. Since 1970, Long Construction has operated the mine equipment for Western Energy Company". The Rosebud Mine is located in Southeast Montana and supplies coal to two 350 megawatt power plants located in Colstrip and one 180 megawatt plant located in Billings. Approximately 30 percent of Western's annual production is consumed by these plants. The remaining production is shipped to the mid-west and burned by utility companies and municipalities.

Jan 1, 1981