Search Documents

Choosing the right valve for corrosive, abrasive slurry applications requires exacting analysis and a comprehensive understanding of the complete slurry process. Within the realm of flow control in abrasive and corrosive slurry applications, there is no room for a one-size-fits-all approach. To ensure minimal maintenance, maximum uptime and the lowest overall cost of ownership, the slurry processing toolbox must contain countless alloy and elastomeric pairings ? each carefully targeted to the particular process medium and conditions. This materials selection process is best tackled by turning to expert slurry application engineers and valve product managers who work closely with customers to specify the optimal valve for the given parameters. ?When plant operators and design engineers apply conventional valves in abrasive applications or use metal seated valves or simply apply the wrong valve for a particular flow control situation, it typically leads to rapid valve failure, the potential for hazardous leakage, unexpected shutdowns and costly downtime,? said Cal Cobb, valve products manager for Weir Minerals North America, manufacturer of Isogate slurry valves for service in mining, minerals processing and metallurgical environments.

Jan 1, 2011

By William Gleason

"With desert temperatures climbing high at Caterpillar’s Tinaja Hills Demonstration and Learning Center near Tucson, AZ in September, a group of editors were given a reprieve from the sun and stepped inside the new Cat Minestar Command Center. The movie theater-like temperatures inside were a welcome relief, and the computer screens stationed around the room were an indication of not just how much things have evolved in the mining equipment sector, but also a peek into the future of where mining is headed.Equipment manufacturers like Caterpillar have always had to deal with peaks and valleys in demand that come with mining, perhaps never more so than in the last five years. Sudhanshu Singh, global product manager for Caterpillar, said that in one month in 2012, at the height of the mining Super Cycle, Caterpillar produced more than 150 large mining trucks (haul trucks that carry 136 t/150 st or more). By contrast, Caterpillar produced about 80 of those trucks in the full year of 2016. Between 2012 and 2016, Caterpillar saw its profits drop by 40 percent.“This shows how cyclical the industry is, and it is a testament to the strength of Caterpillar to be able to tolerate the wide swings,” said Singh. Demand for commodities is once again on the rise as are commodity prices with many signs pointing toward a recovery for the mining sector, and Caterpillar has positioned itself for the recovery. During its 2017 press event in September, company officials emphasized that Caterpillar has added strength in its technology divisions by forming new partnerships and adjusting its operating plan.“At the heart of our enterprise strategy is the operating & execution (O&E) model, a strategic framework to identify areas of the business that either create or consume the most value,” said Caterpillar chief executive officer, Jim Umpleby. “Using the O&E model as a guide, we gain a deeper understanding of where we have a competitive advantage, which is key to generating high returns.”"

Jan 11, 2017

By William Gleason

"The times they are a changing, and, for the mining industry, the optimism is high. On Nov. 8, Donald Trump was elected as the 45th president of the United States, and the Republican Party won a majority of seats in the U.S. Senate and the House of Representatives, ushering in what many hope will be a positive change for the mining and extractive minerals industries.Trump has stated that one of his top priorities as president will be to increase spending on the nation’s infrastructure, which could help spark a boom for mining. He has also pledged to bring back coal jobs and reverse many of the environmental regulations that were put in place by the Obama administration. However, before the mining industry gets too far ahead of itself and plans for another Super Cycle, there are stark reminders that any work in the natural resources sector is complicated and challenging. On Dec. 4, the U.S. Army Corps of Engineers announced that it would not grant an easement that would allow the Dakota Access Pipeline to pass under a portion of the Missouri River in North Dakota. The proposed crossing of the oil pipeline is approximately a half a mile upstream from the Standing Rock Sioux’s Reservation, and for months, hundreds of protestors camped out at the site in an effort to halt the project, saying they feared how it would impact water supplies and sacred lands.Energy Transfer Partners, the company building the pipeline, said the pipeline is a $3.78-billion investment that will connect the Bakken and Three Forks production areas to major refining markets. The company signed voluntary easement agreements with landowners representing more than 85 percent of the properties along the four-state route but faced an organized protest from the Sioux Nation at Standing Rock. The protest gathered momentum and support through social and traditional media and became the focal point of global environmental and indigenous activism. The protestors claimed victory, at least temporarily, when the Corps of Engineers said it would look for alternative routes for the project. It’s a decision that could lead to a lengthy environmental review and one that has the potential to block the construction of the pipeline for months or even years."

Jan 1, 2017

By R. D. Williams

"In a very real sense, Butte, MT is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site.One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot smelter operated from 1881 to 1910, moving Upper Silver Bow Creek to the south and depositing approximately 283,000 m3 (370,000 cu yd) of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 171,000 m3 (224,000 cu yd) of contaminated material. As part of the Superfund remedy, the U.S. Environmental Protection Agency (EPA) proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place, which set the stage for a series of studies that continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. History of the Parrott Mine and tailingsPlacer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery led to a stampede of placer and lode claims. One of the first lode claims located was the Parrot lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow, and it was not until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine.The Parrott Mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the district’s rich copper ore. In 1885, the employees of the Parrot smelter bought the Butte Reduction Works, another smelter. In 1885, dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Fig. 1).By 1890, the various smelters in Butte rendered Butte’s air quality as suffocating (Fig. 2). An 1889 funeral procession was rumored to have gotten lost in the thick smelter smoke and somehow ended up at the Centennial Brewery. A city ordinance was passed late in 1890 in an attempt to control smoke. The Parrot smelter employed approximately 500 men by 1890. Through the 1890s, the tailings produced grew from approximately 91 t/d (100 stpd) to more than 181 t/d (200 stpd). Copper values in the tailings were initially as high as 4 percent, but as the processing improved that was reduced to 1.5 percent."

Apr 1, 2019

By LUIS ALBERTO TORRES-CRUZ

The Plewes method is relatively well known among geotechnical engineers interested in assessing the liquefaction potential of soil deposits. Furthermore, it was one of the four methods considered in the post-failure investigation report of the Feijao Dam I, also known as the Brumadinho Dam, in Brazil. The inclusion of the method in that report is likely to increase its visibility among geotechnical practitioners tasked with assessing the liquefaction potential of tailings. While the authors of the method duly presented it as a screening method, more recent technical literature contains conflicting views on its reliability. Considering the popularity of the method and that the safety record of tailings dams is a cause of great concern, this study assessed the uncertainty of results from the Plewes method. The study concludes that, even under optimistic assumptions, the results of the method are too uncertain for detailed characterization of tailings deposits.

Automated drilling in surface mines is here, it?s successful, and it?s already at work in mines around the globe. Coal, copper, iron and gold mines in large mining countries such as Canada, Australia, South Africa, the United States and Chile are meeting mining objectives previously ruled out as unattainable. Pit Viper automation enables operators to accomplish more objectives safely. Operator assist functions like AutoLevel, AutoDrill, Auto Rod Changer and multi-rig teleremote control are a few of the features mines are using to gain consistent, sustainable productivity.

By William Gleason

"Technology of all forms has experienced exponential growth in recent years, and there is no sign of it slowing down. This growth has presented amazing opportunity and significant challenges in nearly every aspect of daily life. Some of these changes are seen and experienced every day as we turn to our smart phones, tablets and smart watches to help with us with everything from directions to the store to managing our health. And other technological growth takes place far away from the public view but can have as much of an impact on our daily life as does shopping at Amazon or connecting with friends on social media.At the “THRIVE 2018, Innovations Advancing Mining” conference presented by SME on Sept. 27 at the Sheraton Pittsburgh Hotel at Station Square in Pittsburgh, PA, the focus was on innovation and how it affects the global mining industry.More than 100 people were on hand for the inaugural event, and they were treated to a unique program that focused on the cutting-edge innovations that will carry the mining industry into the future while increasing safety and productivity along the way.2018 SME President Barbara Arnold was the driving force behind the conference and put together the technical program with a focus on innovation through the entire mining life cycle and into the future. Talks ranged from more efficient and safer ways to extract minerals to some of the most advanced end uses of minerals and metals, including the use of 3D printing to create precision parts for machines and humans from advanced metal alloys.“We need to adapt new technologies to our industry and develop additional technologies as we provide materials and metals for infrastructure and energy development in the United States, around the globe, and to the Moon and beyond,” Arnold told Mining Engineering. “Our inaugural THRIVE conference sets the stage for these innovations to be applied and to continue to be developed. Our mining industry can only continue to thrive with these advances.”"

Jan 11, 2018

By C. C. Nolan

As the size of the mills get larger and the liners get heavier, abetter means had to be found to handle liner replacement. McLellan Industries is famous for their innovative ideas andwas called upon by an engineering company to develop a mill liner crane. The first crane was developed for Similkameen about 1969 to serve a 32' Ø X 14' Long SAG Mill. The next was Island Copper in Port Hardy, B.C., the same size as Similkameen in 1970. At that time, we took existing hydraulic cranes and modified them to meet the mill configuration. In 1973, we developed a completely new approach for the Southern Peru copper mine at Tacna, Peru for a Ball Mill, size 16'-6" Ø X 19' Long. Each installation required a design study to meet the change in mill size, trunnion size, elevation of floor to feed trunnion, area at the feed or discharge end of the mill. We have supplied self-propelled units as well as lift in. When there is no room at the feed end and if the mill has a trunnion overflow discharge, we have the mill supplier provide a structural frame to span the sump and move the mill liner handier into position with the use of the overhead crane or a mobile crane.

Jan 1, 1999

By B. K. Parekh

The International Symposium on Comminution was organized at Camborne School of Mines, Cornwall England. Papers covered the fundamental and practical aspects of comminution in the mineral industry. Although comminution equipment design has not changed fundamentally during the last 50 years, methods of control and optimization have improved considerably. A simulation model for batch ball milling in the rotating mill was developed as a step toward continuous simulation of ball and autogenous milling. New concepts in jaw crusher technology design and the concept of a 1.6- x 2.1-m (66- x 84- in) jaw crusher with open feed throat has resulted in power savings. The use of cone crusher technology in comminution circuits with particular reference to machine design, plant flowsheet and control figuration has been reported by Boliden Allis, of Sweden. The Whiten steady state crusher model form has been used to develop a quantitative model of 2.1-m (7-ft) cone crushers. This was done by incorporating liner age (wear) and liner length as variables on the selection of particles for breakage and thus on the product size distribution. Another paper by Lira and Karetsky discussed the development of a model based on a multisegment ball mill developed by Whiten and Kavetsky. It is capable of simulating the performance of a coarse grinding ball mill of a given diameter, ball size and mill speed.

Jan 1, 1991

By Daniel T. Eyde

The U.S. Geological Survey (USGS) estimates world production of natural zeolites to be 2.7 Mt (3 million st) in 2013. China ranked ?rst with 2 Mt (2.2 million st), followed by the Republic of Korea at 230 kt (253,000 st) and Turkey at 50 kt (55,000 st). Japan?s production is reported to have increased as a result of zeolites, reportedly low grade local mordenites, being used to treat the low-level radioactive contaminants in the areas surrounding the damaged reactors at the Fukushima Daiichi power plant. China and other countries? high-volume, low-value construction applications, which include dimension stone, pozzolans and lightweight aggregate, are also included in production. This means the production data does not accurately indicate the quantities used in high-value added specialty applications. Consumption in the United States, according to USGS estimates, increased slightly, to an estimated 71.3 kt (78,400 st). Domestic uses for natural zeolites were, in decreasing order by tonnage, animal feed, pet litter, cement (primarily down-hole cement applications by the drilling industry), water purification, odor control, waste water cleanup, fungicide or pesticide carrier, gas absorbent, fertilizer carrier, oil absorbent, desiccant, catalyst and aquaculture. The six leading uses accounted for more than 70 percent of the domestic natural zeolite sales tonnage.

By C. C. Nolan

As the size of the mills get larger and the liners get heavier, a better means had to be found to handle liner replacement. McLellan Industries is famous for their innovative ideas and was called upon by an engineering company to develop a mill liner crane. The first crane was developed for Similkameen about 1969 to serve a 32' 0 x 14' Long SAG Mill. The next was Island Copper in Port Hardy, B.c., the same size as Similkameen in 1970. At that time, we took existing hydraulic cranes and modified them to meet the mill configuration. In 1973, we developed a completely new approach for the Southern Peru copper mine at Tacna, Peru for a Ball Mill, size 16'-6" 0 X 19' Long. Each installation required a design study to meet the change in mill size, trunnion size, elevation of floor to feed trunnion, area at the feed or discharge end of the mill. We have supplied self-propelled units as well as lift in. When there is no room at the feed end and if the mill has a trunnion overflow discharge, we have the mill supplier provide a structural frame to span the sump and move the mill liner handier into position with the use of the overhead crane or a mobile crane.

Jan 1, 1999

By S. D. Rosenthal

"This article will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia and the journey within academia going into the second year.As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. mining engineering degree in May of 1982, my first job with Utah International in the Farmington, NM area took me back to my home state of New Mexico. Some of you will remember that the early 1980s was not a period of prolific opportunities for mining engineers, given low commodity prices, especially for copper (for example, Anaconda Co. had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton).Gold was taking off in the mid to late 1980s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia. So after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma Copper purchase, Beanup and HBI) and was reviewing assets and staffing, so internal opportunities became scarce. Employees were encouraged to “leave the company and find work elsewhere.” So, off I went to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, AZ, and a posting with Phelps Dodge (now Freeport- McMoRan). After 12-plus years without living close to snow, we moved to the Denver, CO area in a new position with Newmont Mining Corp. Along the way I became a professional engineer (Nevada) and completed a masters in project engineering and management. After 11 years with Newmont, I moved to Butte, MT where I accepted a position as assistant professor of mining engineering."

Jan 1, 2015

By J. M. Christian

Silver has been a much maligned metal in recent years. In the last three and a half years the price has fallen from around US$7.00 -$7.80 to as low as $3.50 this spring. It has consistently under-performed most other precious metals in the past few years, and has fallen to its lowest levels since the late 1940s in inflation-adjusted terms. Perhaps this is beginning to change. Since April, silver prices have outperformed gold and platinum. While this may continue in the years ahead, key questions remain regarding the pace and timing of any future silver price advances. I want to talk about the supply and demand factors that have led silver to its recent position. Also, I will outline a possible path for silver supply, demand, and prices for the next several years. Before I dive into my discussion of the silver market, allow me to explain who I am. One of the points we always make to clients early in a relationship is that, when you are listening to someone's opinions, you always must remember who it is you are listening to, and why he might be saying whatever it is he wants you to hear. So often, people take opinions from brokers, traders, or investment advisors as gospel truth, never stopping to ask themselves two key questions: Is there any reason to believe that this person knows what he is talking about, and, second, is he trying to sell me something, in telling me this.

Jan 1, 1992

By B. Mather

I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming's discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2O.; Na2e = % Na20 + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage. to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete.

Jan 1, 1997

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By Weston Bourret

The need for wartime supplies of uranium for the Manhattan Project prompted a 1944 study of uranium in South Africa. Uraninite had been reported by R.A. Cooper in 1923 in a Witwatersrand heavy- mineral concentrate, and the search for uranium, therefore, included the district's 30 operating mills. The method of investigation was simple: take bulk concentrate samples from the Wifley tables and determine their mineralogy. Samples were taken on a daily basis, although weekly composites also were taken of some mills. In 1944, most mills had simple gravity circuits and produced (I) a gravity concentrate, and (2) an all-slime [-75 pm (-200 mesh)] product. The tonnage throughput was known, and from that, head assays could be calculated. Concentrate samples were sent to the United States for chemical analyses. A Geiger counter set up in a Johannesburg hotel room provided preliminary data. The early data showed uraninite to be widespread. Microscopic, mineragraphic, and siezing tests were all under- taken in Johannesburg. Ultimately, tests led to a high grade (+90%) uraninite concentrate. Platinum and other heavies were the impurities. In seven months, the investigations had reached the stage where it was possible to forecast an annual production of 5.4 to 7.3 kt (6,000 to 8,000 st) of U3O8. The estimate is still realistic. Additional details are found in Bourret (1981).

Jan 1, 1991

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By B. J. I. Adair, K. R. Weller

The bulk scavenger tailing from Aberfoyle's Hellyer Concentrator, which represents about one-third of the total tailing, runs about 2.5-3 g/t gold and 140-200 g/f silver. Both values are very finely disseminated, particularly the gold. Aberfoyle wished to establish whether ultra-fine grinding followed directly by cyanide leaching could be applied to the tailing for recovery of gold and silver. The work comprised the determination of gold and silver recoveries as a function of grind size and leaching time, the specific energy consumption required for continuous wet grinding of the tailing to the specified product size in a small horizontal continuous stirred mill, and an estimate of the rate of media consumption. The maximum extraction of gold, 23.3% was obtained from the finest product, with the highest cyanide concentration and longest leach time, confirming earlier work. A similar result was obtained for silver. The specific energy requirement for milling rose from 27.7 kWh/t for a P80 of 8.1 um to 219 kWh/t for a Pea of 2.3 um. The consumption of ceramic media was about 1.6 g/kg of final product. An extensive QEM'SEM Trace Mineral Search on the unground tailing failed to identify any gold-bearing particles but did identify silver-bearing particles which displayed a variety of textural associations and liberation characteristics.

Jan 1, 1998

By Pierre M. Matheron

TRANSMANCHE-LINK is responsible for designing, developing and implementing the project for a fixed link under the English Channel, comprising two running tunnels of diameter 7.6 metres and a service tunnel of diameter 4.8 metres. The three tunnels will all be 50 km long, with 37 km bored through chalk marl at a depth of 40 metres under the sea bed. The tunnels will be driven from both sides of the channel from intermediate addits above the coastline on either side with a 55 m access shaft at Sangatte in France and two "descenderies" or inclined tunnels addits and a shaft at Shakespeare Cliff on the English side. A total of eleven tunnel boring machines will drive the 150 km of tunnels. The major part of the tunnel linings will be built of precast reinforced concrete segments, and two plants have been specially built to produce the necessary 725,000 segments. Seven million cubic metres will be evacuated on wagons along the tunnels and then lifted by belt conveyor on the English side, and by hydraulic mucking from the bottom on the French side. Preliminary work started early in 1987 with manufacture of the first boring machines, construction of five precasting plants, boring of the Sangatte shaft in preparation of the Shakespeare Cliff entrances. The principal project dates are :

Jan 1, 1987

By D. D. Lauriski

The Mining Division of Utah Power and Light Company is located in the coal fields of southeastern Utah -main office in Huntington, Utah. The Division will produce 6.5 million tons of low sulfur steam coal in 1988, making UP&L the largest underground mining operation west of the Mississippi. Coal is mined from three underground mines utilizing continuous miner and longwall mining methods. All coal produced by the Mining Division is utilized at UP&L's two largest steam-electric power plants, the Hunter and Huntington plants with a combined capability of 1,995,000 Kw. At UP&L we believe that to achieve success a company must have clearly defined goals which are understood, communicated and shared at each level of operation. We have also found from experience that a safe operation is generally an efficient and productive operation. As a Division, we have established a goal to achieve the safest, most efficient operation in the country. This is an ambitious goal. To achieve such a goal requires real commitment and a safety/training program capable of achieving needed results. The following is an overview of the program we have established at UP&L which has enabled us to reduce our accident frequency rate from over 40 in 1980 to 8.00 at present, as illustrated in Figure 1.

Jan 1, 1989