Search Documents

By L. L. Oriard

There are certain site-specific geological and physical features of a rock mass which control its behavior under the dynamic stresses induced by the action of explosives. It is essential that blasting technology be adapted specifically to those features. There does not exist a single, simple "right" way for each type of blasting operation, but rather each operation must be custom-designed for each site. When this is done, it is often possible to produce unusual but highly desirable end resglts, such as undisturbed narrow rock walls, monoliths and square benches. Although the techniques illustrated here were developed specifically for "sculpture blasting", the geomechanics principles would apply to other types of blasting control, both large-scale and small-scale. Because the techniques are designed more for the purpose of modifying the site responses which would ordinarily be expected than they are to developing new "blasting formulae?, the name "Modified Site Response Blasting" will be used.

Jan 1, 1984

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1997

By Jaisen Kohmuench, Michael J. Mankosa

Flotation has long served as the foundation for sulfide mineral recovery. As ore grades decline, however, this traditional approach is being pushed to the limit. Nowhere is this more evident than in the challenge of recovering coarse, partially liberated particles — an area where conventional flotation systems typically underperform due to excessive turbulence. As a result, valuable coarse minerals are often lost to tailings. Fine grinding has become the default solution, although with the added burden of higher operating costs and more challenging tailings disposal. To address the challenge of coarse particle recovery, Eriez developed the HydroFloat, a technology that uses a novel fluidized-bed approach to extend the upper particle size range of flotation significantly. The HydroFloat can recover particles exceeding 0.5 mm in diameter with a sulfide surface expression as little as 2 percent. Coarse particle recovery allows for optimization of comminution circuits for coarse gangue rejection before fine grinding. A substantial increase in overall tailings particle size provides higher water recovery due to improved drainage and allows for consideration of a dry, stacked tailings option instead of a tailings dam/impoundment. The technology’s transformative potential has not gone unnoticed. In recognition of its impact, Eriez was honored with the 2024 Robert E. Murray Innovation Award, commonly referred to as the Murray Award, by the Society for Mining, Metallurgy & Exploration. This prestigious award was established in 2017 to recognize organizations that advance the mining industry through the implementation of technical innovation. The HydroFloat stands as a fitting example of how creative thinking and industry collaboration can solve long-standing technical challenges.

Oct 1, 2025

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

By Matthew Goff, Russell Lutch

The Great Lakes Water Authority (GLWA) operates the largest regional water authority in the State of Michigan. Two of the tunnels supplying raw water to the system from the Detroit River are the Springwells and Northeast Tunnels. The existing 70- to 90-year old concrete lined tunnels have experienced distress and cracking over their life requiring non-structural repairs to sections of the tunnels. For the repair, an interior stainless-steel segmental liner plate system has been designed to restore the watertight capacity of the tunnel liner and resist the exterior hydrostatic groundwater pressure in a dewatered condition. The team is utilizing a “wet repair” approach to perform the necessary repairs while the tunnel remains fully flooded and operational. To test and validate the tunnel repair approach, a full-scale mock-up of the proposed repair has been performed using underwater equipment and divers.

Dec 1, 2022

By Bryan Ulrich

Knight Piésold?s annual roundtable discussion was held at the Red Lion Hotel and Casino in Elko, NV on March 14. This year the title was, ?Roundtable discussion on material co-disposal/ co-placement in the mining industry.? This topic was chosen because of the benefits that the mining industry could realize through the advancement of improved methods of storing tailings and mine waste and from reducing short-and long-term environmental hazards while reducing the footprint of these facilities and making strides toward attaining a walk-away solution. Knight Piésold had a local representative, Bryan Ulrich, as well as representatives from its Denver, CO office, including Tom Kerr, president of Knight Piésold?s U.S. practice, and Jeff Coffin, Ph.D., geotechnical engineer, to help facilitate the discussion. The event played host to about two dozen attendees from several western states. Attendees included personnel from more than 10 mining properties, various corporate offices and academia. The purpose of the roundtable was to exchange ideas and information pertaining to broad topics revolving around the subject of co-disposal/co-placement in the mining industry. Compared with traditional conferences and symposia, the roundtable forum tends to provide a less inhibited format for discussion. In the roundtable format, lively discussions and applicable tangential departures are encouraged. This was the seventh in the series of the Elko Roundtable events. Previous roundtables pertained to: ? Heap leach pad design, construction and operation. ? Design, construction and operation of tailings storage facilities. ? Site-wide water considerations. ? Mine closure and cover design. ? Strides toward sustainability in mining. ? High-density tailings, paste and filtered tailings. Acid rock drainage for engineers and environmental scientists.

Nov 1, 2013

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By Irving Hoch

INTRODUCTION The demand for tunnelling can be related to urban population size and density; often, tunnelling occurs when a certain city size and density threshold is reached, and increases thereafter as a function of those population characteristics. Subways for rail mass transit are the most notable example, of course, but tunnels for water supply and perhaps for sewerage can also be related to size and density. As cities grow large they sometimes outgrow their local water supply and have to import water from distant places via tunnels; witness New York City, Los Angeles and San Francisco. And it has been suggested that Chicago use deep tunnels for storm water storage because tertiary treatment to meet water quality standards will require treating storm water runoff.(1) Other uses of underground space also increase with urban density, e.g., underground parking, concourses and shopping centers such as Rockefeller Center in New York City and the Place Ville-Marie in Montreal. These examples can be viewed as illustrative of the central point of urban land economics. As the number of people locating in a place increase, they bid up land values and make the more intensive use of land economic, with land defined to embrace the space both above and below the surface. Hence, we are led to think about the city, and of urban land use, in three dimensions. Now, if we accept the relation of underground space use to urban size and density, recent demographic trends seem anything but hopeful for future tunnelling demand: urban density is declining, population growth is slowing down generally, and there

Jan 1, 1974

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By Fabio Mielli

The mining industry is a multifaceted industry with special characteristics that make efficient and intelligent operations uniquely challenging, and subsequently call for distinctive and tailored solutions. Not only does mining call for processes that are complicated and energy intensive, but complex material movements and an intricate logistical chain add to the industry?s obstacles in achieving sustainability and performance. This article explores three major challenges and the resulting issues currently being faced in the industry, as well as potential solutions to these impediments by use of energy management, automation and control strategies.

Jan 1, 2011

By P. Davis

With new mineral deposits found in areas of difficult terrain, and annual production capacity increasing in mines over the last decade, the aerial ropeway is proving to be a viable, economic method of transportation from mine to processing plant. Of the more conventional designs, a bicable ropeway is more suited to difficult country than the simpler monocable. The bicable, however, does have limitations in the difference in levels it can accommodate in one section at a given capacity. This is noticeable where hilly terrain and high capacity imposes a limit on the length of each section. Increasing the number of sections for a relatively short conveying distance tends, in the case of conventional bicable, to unbalance the normally favorable economics of the ropeway. In addition to analyzing hauling rope stresses, other areas have to be considered when looking at high capacity ropeways. Bucket capacity, speed, and the wheel load on track ropes are examples. These and other factors led British Ropeway Engineering Co., of Sevenoaks, Kent, UK, to produce the twin-track system. Using twin track ropes, larger capacity buckets, and, if the height differential warrants, the installation of twin hauling ropes, BRECO produced a ropeway design for areas of hilly terrain and at higher capacities than had been considered suitable for aerial ropeways. Designs have been produced for systems handling 1.5 kt/h (1,650 stph), and the potential exists for expansion to above 2 kt/h (2,200 stph). The arrangement of ropes provides high stability of the cars and is especially suited to areas where high winds occur during normal operation. This development allows the aerial ropeway to be applied economically in difficult areas and at the increasingly high capacities demanded by engineers. Ropeway Transports Limestone to Sudan Cement Plant Maspio Cement Corp. of Atbara, Sudan, will soon use an aerial ropeway to deliver its entire limestone requirement 20 km (12 miles) from quarry to plant. The Atbara plant is located north of Khartoum, near the east bank of the Nile River. The quarry is west of the river, in hills rising from flat desert country. The original transport system was a 24-km (15-mile) railway from the quarry to the west bank and a monocable ropeway that crossed the Nile and continued to the fac¬tory, a distance of about 2.5 km (1.5 miles). This original ropeway had a capacity of 60 t/h (66 stph). With the extension of cement-making capacity in the late 1970s, 2.5 kt/d (2,755 stpd) of limestone was required and a new mono-

Jan 3, 1984

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

The paper introduces a new rock mass cuttability classification (RMCC) system for roadheaders used in coal mines. It includes performance prediction models for both axial and transverse roadheaders, based on six parameters: uniaxial compressive strength, Cerchar abrasivity index, volumetric joint count, strike and dip of joints, joint aperture, and groundwater condition. The study validates the RMCC system through field and laboratory measurements, showing high correlation coefficients between net cutting rates and RMCC indices.

Nov 1, 2023

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By T. Fernandez, V. Juchen, C. Petter, F. Cantini, V. Lenz, V. I. Araújo, R. Petter, R. Darrigo, A. Young, I. G. da Costa, J. Oppermann

There are many methods to estimate costs quickly. One of these is the Parametric Method, where costs are estimated from general algorithms (or curves). Derived from an original tool based on the O’Hara model, a software called MAFMINE was developed. MAFMINE is based on parametric models to estimate investment and operational costs in mining. The software itself is based on the use of a computer model known as client-server. However, the model needs new inputs from advances made by the mining industry, mainly in terms of electrification, automation, digital transformation and preconcentration to face Environmental, Social and Governance (ESG) concerns. Thus, this work was to prepare a new core module ready to incorporate the new technologies aiming to deliver operation and capital costs associated with environmental impact mitigation. The tool generates an order of magnitude estimate for CAPEX and OPEX to establish a very first Discounted Cash Flow (DCF) in a mining venture. For quick evaluations, at a preliminary level, the results are very promising.

Mar 2, 2022

By S. Šolar

The countries of Southeast Europe are rich in aggregates, but neither management nor supply are coordinated within or across this area. There are open issues in SEE on the local scale as well as on regional/national and transnational scales that will need to be addressed in order to meet societal expectations related not only to the security of aggregates supply for economy, but also those linked to environmental concerns and social issues. The Sustainable Aggregates Resource Management project (SARMa), an EU Southeast Europe (SEE) activity, has as its objectives the development of common approaches to sustainable aggregate resource management (SARM) and sustainable supply mix (SSM) planning in SEE. In this paper we describe the SARMa project structure and report results for Work Package 3 activities pertaining to best practices for environmental management, the reduction of illegal quarrying, and the promotion of recycling of quarry wastes, construction and demolition wastes and other materials.

Jan 1, 2011

By Frank W. Pereira

The Montana Talc ore body was discovered in 1983 in Montana's Gravelly Range, about 40 km (25 miles) south of Ennis. Initial drilling indicated a 910-kt (1-million st) ore body of high purity talc. Preliminary analyses on ore cuttings included chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. Results indicated it was similar to talc currently being marketed from Montana and it would probably have good commercial value. Based on the positive test results, a test pit was made and a 180-t (200-st) sample of ore was mined. A portion of the ore was ground to various particle sizes and evaluated to determine its strengths, weaknesses, and other characteristics. The deposit is located close to the Cyprus Yellowstone deposit. It was therefore believed that Montana Talc ore may possess many of the same characteristics. Testing and analyses showed the talc to have a high purity and an extremely large surface area, even for Montanatype tales. The ore was also situated in a massive deposit, indicating low cost mining. While the lab analyses were encouraging, the true evidence would be obtained from commercial tests in the marketplace. About 91 t (100 st) of ore were ground to product specifications for pitch control, paint filler, and plastics filler. Consumers were contacted and requested to evaluate the sample talc products. A major trial for the talc as a pitch control agent was arranged at a Northeast paper mill. The trial indicated the new Montana Talc product performed as well or better than the current standard in the industry. In fact, due to a minor modification in the compaction process to make the transport of the talc easier, the product had substantially less dust than the currently used product. The operating people at the paper mill requested that management purchase this talc. Trials were also run at paint plants for use as a pigment filler. And the talc was fabricated into a number of plastics compounds. The initial product tests were largely positive and provided encouragement to proceed with the project. Different grinding mills were used and their performance evaluated. Significant data were generated by the custom grinders. They indicated how the Montana Talc ore ground and the particle size distributions produced at different grinding settings. Encouraged by the positive marketing tests, a prefeasibility study was commissioned. A talc grinding plant and mine plans were designed and capital and operating costs estimated. Initial economics showed an attractive return. The operating costs were among the lowest in the industry. The positive economics, along with the excellent results by the products in the marketing tests to the paper, paint, and plastics industries, led to the recommendation to proceed with the project. Plant construction began in June of 1985. The Montana Talc Co. (MTC) analyzed the data from the commercial tests. Based on the product's outstanding performance and the uniqueness of its high purity and platy structure, a strategy was developed to position the company as a premium talc supplier.

Jan 1, 1989

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1988

By Hans von Michaelis

The renaissance in extractive metallurgical practices for gold and silver recovery is far from over. This is one conclusion of a three year investigation into innovations in Cold & Silver Recovery by Randol International Ltd. (1981, 1983). The six volume reference report reviews a host of new processes and innovative applications of older metallurgical practices. Some of these were summarized by von Michaelis (1982, 1982a). There are several reasons to expect this renaissance to continue. One reason is the nature of gold and silver deposits. The list of known occurrences of These metals is very extensive. There are literally tens of thousands of prospects but over 99% of these are too low grade, too small or too refractory for a viable operation employing conventional processing.

Jan 1, 1983