Search Documents

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

By G. Paul Anderson

Personnel at Utah Copper Division's Bingham Canyon Mine use current computing technology to compile pertinent production statistics and mining plans. Within hours after the day's work has been completed, concise reports summarizing the previous day's production statistics, actual production vs. budget statistics, the location of shovels relevant to the mining plan, the performance of equipment, equipment next scheduled for maintenance, etc. are available at the terminals located throughout the mine. Also, engineering personnel us e computerized systems, directly from their offices, to assist them in the timely development of mining plans. Timely and concise reporting and planning capabilities such as these assist mine personnel in their efforts to review mining progress and equipment performance, and as such they are in a better position to detect adverse trends early and to seek appropriate resources or make changes in plans or practices.

Jan 1, 1977

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product. The Hanna Mining Company's Groveland plant is no exception. The Groveland Mine is located in Dickinson County on the Upper Peninsula of Michigan. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper, and various iron silicates. (1) Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals. (2) A general flowsheet is shown in Figure 1. Flotation of the spiral tailings makes up about 75% of the concentrate. A minor amount of concentrate, less than 3%, is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tons per year.

Jan 1, 1968

By S. S. Hsieh

The important carboxylic acid components of tall oils were tested individually as phosphate flotation reagents. These included C18 unsaturated fatty acids and C10 to C18 saturated fatty acids and resin acids. These experiments were conducted to evaluate such factors as the degree of unsaturation, hydrocarbon chain length, isomeric form, side-group modification, and cyclic structure. The effects of mineralogical characteristics on flotation response also were considered. The results of this systematic evaluation provide guidelines for selecting efficient substitute reagents and also provide fundamental data for further research on improved flotation technology.

Jan 1, 1980

By Bo Hyun Kim, Mark K. Larson

This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock-mass behavior in longwall coal mines in highly stressed, bump-prone ground. The floor-heave and nofloor- heave phenomena at a western US coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria (i.e., Mohr–Coulomb or Hoek–Brown failure criterion). The previous numerical study demonstrated these phenomena using a user-defined model of the s-shaped brittle failure criterion in conjunction with a spalling process in the FLAC3D numerical modeling software. The results of the FLAC3D modeling agreed with the observations of the relative amounts of heave from each gate-road system. However, the FLAC3D model adopted many assumptions and simplifications that were not very realistic from a physical or mechanical perspective. To overcome the limitations of the FLAC3D model, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. The effect of stress rotation in the mining-induced stress field was considered by using a different geometry of rock fractures in the coal seam. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) were also considered by using Monte Carlo simulations. Consequently, the 3DEC models using the DFN technique resulted in predictions of floor heave that agreed with observations of the relative amounts of heave from each gate-road system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Apr 14, 2022

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By K. L. Woodruff

Shredding is the usual first step in processing municipal solid waste (MSW) for resource recovery. This unit process requires high capital cost and, usually, considerable maintenance cost. In addition, some shredders at times will render certain components of the MSW in a form difficult to recover. This is particularly true in the way metal cans are distorted and the way glass is pulverized. A trommel screen was proposed (1) to pre-process packer truck refuse prior to shredding. Part of the logic for this step is that the portion of raw refuse already within the specified shredder output particle size range would bypass the primary shredder and proceed directly to further processing, such as to an air classifier or secondary shredder. This would reduce the throughput of the primary shredder and allow certain recoverable materials, such as glass, to remain in larger piece sizes, important for recovery. In this way, operating costs for the shredder would be reduced and the recoverability of materials, and hence the revenue, increased.

Jan 1, 1975

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By T. Vincze

Effective coal mine face ventilation, for remotely controlled and automated mining systems, is essential for the control of methane. The evolution of new mining equipment and methods has required changes and improvements in face ventilation methods. One emphasis today is on the use of remotely operated and automated mining systems that can be used to make continuous cuts of 6 m (20 ft) and deeper. U.S. Bureau of Mines research is studying ways to more effectively ventilate these extended cuts. Two face ventilation techniques that utilize either blowing brattice or a jet fan for deep cutting are examined in this paper. Bureau of Mines procedures for evaluating face ventilation systems are also discussed.

Jan 1, 1992

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995

By Doandy Yonathan Wibisono

Shotcrete is a versatile and widely utilized rock support material in mining and civil engineering projects due to its adaptability, strength, and efficient application. It immediately stabilizes rock surfaces, effectively controlling loose materials and preventing rockfalls in underground excavations. This paper focuses on assessing and analyzing data from observations of nozzlemen (shotcrete sprayers) during primary ground support activities in an underground mine. The study highlights the importance of nozzlemen’s skills in ensuring the quality of shotcrete application, which is critical for underground mining operations’ structural integrity and safety. A comprehensive training program and field support were implemented to enhance the nozzlemen’s proficiency. The training set covered theoretical knowledge and practical techniques to improve shotcrete application daily. Proficiency improvement was assessed using quantitative metrics, with rebound percentages decreasing by 5–14% as nozzleman competency increased. The results of this initiative showed significant improvements in shotcrete quality, including increased efficiency, reduced waste, and fewer reworks or rehabilitations. The findings aim to contribute to a broader understanding of best practices in shotcrete application and nozzlemen training, ultimately enhancing ground support application measures in the mining industry.

Feb 1, 2025

By R. W. Utley

The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data, and factors affecting the product ion of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsylvania State University to study the possible elimination of air pollution from coal refuse fires by producing a low- carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product.

Jan 1, 1965

By M. C. Rockwell

There are about 1.8 Mt (2 million st) of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia currently stockpiled in a tailings pond at the mill site. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a potential source of soil conditioner material for the local market. However, the fine particle size, 98% passing 147 pm (about 100 mesh), and a moisture content of 20% make their handling, shipping, and application to soils difficult. The tailings were agglomerated into small hard pellets with various amounts of soil nutrients, moisture content less than 13%, and pH values ranging from 6.5 to 8.7.

Jan 1, 1987

By Todd Burchett

Mining engineers spend countless hours and resources when designing a new underground coal mine. Their primary objective is to design the safest and most efficient operating mine with regards to coal production. A key variable often overlooked in this design stage is the slope conveyor. Typically, a slope conveyor is expected to operate with a 98-percent or higher availability. However, too often little effort is put forth by the mining engineer to optimize its design. Coal companies will rely on engineering, procurement, construction and management (EPCM) companies for the preliminary design, because the slope conveyor will be considered part of the surface material handling processes. This preliminary design will be used when soliciting quotations for the slope conveyor. Unfortunately, EPCMs may not have enough expertise with conveyors to optimize the design. This expertise is available with an original equipment manufacture (OEM) of conveyors, which ultimately may be responsible for supplying the slope conveyor. Each OEM will provide a bid package that represents what it considers to be the optimal design.

Jan 1, 2013

By C. H. Lee

The world-famous Sang Dong Mine in the Republic of Korea has long been one of the world's greatest tungsten ore deposits. Over the years, the development of the Sang Dong deposit has steadily increased to a point where it now exerts a great influence on the world tungsten market. The mine is located in the mountains of the province of Kang Won Do, approximately 150 miles by road due east of Seoul, the capital of the Republic of Korea. In recent years the transportation system in Korea has greatly improved and the mine is now serviced by an excellent secondary type road from the new railroad line which is 20 miles away. The Sang Dong operation is made up of the underground mining, beneficiation mill, chemical refinery, tungsten metal plant, bismuth refinery, acid plant, foundry and machine shops. The bismuthinite production from the Sang Dong Mine is also of considerable importance, The output accounts for nearly 10 per cent of the world production of bismuth. A small amount of molybdenite concentrate is also recovered from the flotation operation.

Jan 1, 1962

By R. B. McCammon

Four areas have been identified as favorable drill-site locations for determining whether or not a suspected prophyry copper deposit exists in Rowe Canyon, Nevada. Favorability is based on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for the elements zinc, silver, arsenic, antimony and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1979

By Joseph A. Dos Santos

"The subject of this writing was first published in 1998 with the emphasis on the hardware cost comparison. Other costs, such as the required land area and spatial volume, were mentioned but not emphasized, as these were not deemed as important for new projects where the space was appropriated as required. During the last decade, these other costs have proven to be more than equal in importance. These costs are emphasized here through specific accounts of actual highangle conveyor installations that demonstrate the importance and the high-angle advantage An update on the progress in sandwich belt highangleconveyor technology is also provided.Origin and progress in sandwich belt conveyorsCover belts of the 1950s. Large volume, highangle conveying by “conveyors with cover belt, dates back to the early 1950s, when such systems were employed at the bucket wheel excavator boom conveyor in German lignite mines to increase the depth of cut without increasing the boom length. Various systems were developed, patented and built. These systems were not a lasting success for various reasons, which are noted by Rasper[1]. In his 1958 “Review of Cover Belt Systems,” Rasper summarizes the characteristics which are worth pursing and those that should be abandoned. The former are akin to good conveyor engineering. The sandwich belt conveyor model. The first sandwich belt conveyor model allowed calculation of the required hugging pressure to develop the bulk material’s internal friction and preclude material slideback. A modern, accurate version of the sandwich belt conveyor model is presented in Fig. 1. This model depicts accurately a derating of the material cross-section allowing an ample belt edge distance that can tolerate normal belt misalignment without material spillage. The calculations must thus recognize that only part of the hugging pressure is imparted onto the material with the remainder transferred belt edge to belt edge affecting a material seal. Mathematical development of the sandwich belt model is covered by Dos Santos and Frizzell in their 1983 article, “Evolution of Sandwich Belt High Angle Conveyors.”"

Sep 1, 2016

By Anthony W. Garson

Good morning, ladies and gentlemen: It is a pleasure to be here this morning as a representative of Dean Witter Reynolds; one of the foremost international investment firms in North America. My colleague, Hugh Wilmer (who will be speaking to you a little later), and I are involved as research analysts in the research and writing of published reports containing recommendations on the buying or selling of North American and South African gold and silver mining shares. Our talk this morning will focus on the gold mining operating costs of North American and South African gold producers. However, I am not going to bore you with reams of statistics on the operating costs of large numbers of gold mining operations; how meaningful would this data be to you? Instead, I will discuss what the investor should look for, and how he should use this knowledge in making his investment decision.

Jan 1, 1984