Search Documents

By Berthold Pilz

The importance of a power economy that is efficient both in technological and economic terms has been clearly recognized in recent years. In 1977 the German Federal Government therefore introduced its Energy Research and Energy Technologies Program 1977-1980, which consolidates the government activities in the field of nuclear and non-nuclear energy research. The priority objectives of this program can be summarized as follows: safeguarding the medium- to long-term energy supply in the Federal Republic of Germany at reasonable overall macroeconomic cost, taking into account the requirements of environmental protection and the safety of the population. In the field of coal mining technologies, about 200 research projects are currently under way. A total of DM 1.7 billion is earmarked for research to be conducted in this area between 1977 and 1980.

Jan 1, 1979

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By Sangwhui Cho

In comminution processes including crushing, grinding and pulverizing, the efficiency of the comminution system is very low. Since the early 1980s, research has been conducted to increase the efficiency of pulverizing mills. Additionally, the application of microprocessors and Personal Computers to process control have come into general use. Given appropriate models of the process and control algorithms, these systems can economically control comminution processes. The ring-roller type mineral pulverizer is known as an energy saving mill. In this study, a control strategy to increase the efficiency of this type mill is explained.

Jan 1, 1992

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

By Scott Ellenbecker

Mining has evolved in recent years, taking steps forward in the way that the industry is considerate of the environment and the communities in which it operates. Technology plays a major role in that evolution. Osisko Mining?s Osisko Mine near Malartic, Quebec is developing a new way of doing business. One manager said, ?We are building the Osisko culture,? but the company is doing many things that could become industry changers. Much of the change is driven by mine ownership and management to offer a better workplace and better community relations. Mining equipment manufacturers are changing, too, by engineering products with more operator comfort, fuel economy, ease of maintenance and more cleanly designed machines. And for those drills working close to communities, smaller bore sizes and sound retention are just two changes for the better.

Jan 1, 2012

By Cyrus W. Field

Chemical, mineralogical, and petrographic data have been obtained for suites of plutonic rock samples from the Guichon Creek Batholith of British Columbia and the Mineral-Iron Mountain-Sturgill Peak- Cuddy Mountain-Peck Mountain areas of western Idaho. Intrusions at these two geographically separate localities represent composite plutons ranging from early gabbro through quartz diorite to late grano- diorite and more silicic-alkalic phases. They are early Mesozoic (200 m.y.) in age, and contain porphyry-type mineralization in close spatial and temporal association with late-stage intrusions of porphyry, aplite, pegmatite, and (or) breccia. Country rocks are eugeo-synclinal assemblages of metasedimentary and metavolcanic greenstones of Permian, Triassic, and Jurassic age. The petrochemical evolution of these intrusions, and the effects of subsequent hydrothermal alteration and metallization, are illustrated by standard ternary diagrams of the major oxide and mineralogical data. Samples plotted on an AFM diagram suggest a calc-alkaline magma trend. However, their distributions on NKC and Qz-Kf-Pf diagram show well-defined trondhjemitic (Na20-rich) and tonalitic (quartz-rich) variants to this trend, which are similar in part to those reported for mineralized island arc plutons of the northern Caribbean and southwest Pacific, but which contrast markedly to those for continental plutons of the Bingham District, Boulder Batholith, districts of southern Arizona, and elsewhere.

Jan 1, 1975

By Jan Tegtmeier, Horst Gerhardt

INTRODUCTION Under certain circumstances the closure of former mines which are located above a certain flood level can result in problems such as the emanation of detrimental substances after having completed filling and reclamation operations. This especially applies to uranium mines in which the radiation dose could far exceed the dose of natural background radiation. By means of an example of the uranium mining in Germany in the following it will be demonstrated how to cope with this problem. On the basis of comparative investigations in various vein deposits and using ventilation scheme calculations proposals for the optimization of the necessary forced ventilation can be submitted. REPORT ON SITUATION In the period 1946 - 1989 the former Soviet-German joint- stock company "Wismut" developed into the biggest European uranium producer with a total output of about 220.000 t of uranium. A major mineraldeposit district was the deposit of Schlemaf Alberoda in the Saxon Ore Mountains, in which 80.000 t of uranium were produced. Thus it is among the biggest uranium de- posits of the world, from which various other metals were at- tracted for many centuries. The exploitation of the Schlemal Alberoda deposit involved steep veins in regions near the surface as well as depths of 1.800 m. Until 1991 a total excavation space of 40 million m3, which is flooded at present, was produced. With the average increase in the water level of 80 cm per week the final flood level is expected to be reached in the year 2003. The shaft 373 at present still being used for ventilation will be no longer available since the second quarter of 1998 after flooding the -540 m level because it is not connected with the excavation system near the surface. As a study shows, a radiation dose far above the natural back- ground radiation has to be expected for the town of Schlema due to the extensive mining activities near the surface and due to the subsequent displacement with missing depression fo the main mine ventilating fan. An uncontrolled air flow containing radon leaves the open mine excavation due to the effect of the natural ventilating pressure and emanation caused by the barometric pressure drop with atmospheric pressure fluctuations. This mine air with its high-level radioactive equilibrium results in a high radiation dose in buildings (see Figure l). After having switched off the main ventilating fan in order to investigate the effect of the missing depression the increase in radon concentrations amounted up to 700% in various buildings of Schlema. This was partially due to the inversion state of the weather at that time. The high radon concentration has detrimental effects on the health of the population and of the miners working on the further reclamation in regions above the flood level. ANALYSIS OF THE RADON EMANATION RATE EXPECTED Considering the composition of the radon inflow from the mine workings it becomes evident that 80 % of the radon inflow originates from abandoned excavations and only 20 %from open ventilated mine excavations. This fact has to be taken into account for the ventilation after having reached the final state of flooding. After completing ventilation the radiation dose on the surface is mainly due to the radon emanation from excavations close to the surface. Investigations of the Wismut GmbH showed the in- crease in the specific radon emanation rate by a factor of 100 for abandoned excavations as compared to new drivings. One reason is the larger specific surface of abandoned galleries caused by displacements due to mining activities as well as by fall of hanging. Furthermore the radon can enter the gallery through joints, which have subsequently opened by convergences. All these effects result in a larger free surface available for radon diffusion. The large number of drivings in the deposit sections near the surface and the fact that the highest uranium contents are found near the surface as well as the high fracturing are further reasons for higher emanation rates. Considering these facts it can be expected that the radon inflow of 10.000 kBq/s, which refers to an open mine excavation of about 1.4 million m3, represents a minimum. Only by increasing the specific surface, for which a numerical value has still to be determined, this value will increase with certainty. An extensive radon emanation from the residual excavation, which cannot be flooded, can only be prevented by maintaining the ventilation system. The low pressure produced by the fan in the mine openings prevents the emanation of air containing radon due to the effect of the natural ventilating pressure. Without the controlled withdrawal of the radon the population as well as the miners working on the further reclamation in areas above the flood level would be endangered. Therefore the follow-

Jan 1, 1996

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By Wade W. Bristol

The Jerritt Canyon Joint Venture project is located about 80 km (50 miles) north of Elko, NV. It produces approximately 9.3 t/a (300,000 oz/year) of gold. The joint venture is 70% owned by Independence Mining and 30% by Meridian Gold. Independence Mining is the operator. The Jerritt Canyon Joint Venture started operations in 1980 by mining a series of open-pit mines. The discovery of deeper ores during early 1990s made it neccessary for the operation to mine a large portion of its annual production by underground mining methods. Underground production started in 1993 at the West Generator Mine. This was followed by the Murray Mine in late 1994. Two additional underground projects are being developed. Underground mining at Jerritt Canyon is scheduled to produce about 3.9 t (128,000 oz) in 1997.

Jan 1, 1997

By Peter C. Ashbrook

The Regional Copper-Nickel Study was initiated in large part because of fears that copper-nickel development might cause adverse effects on the environment from air pollutants such as sulfur dioxide (SOZ) emissions from a smelter, and water pollutants such as acid mine drainage. The Study comprehensively examined the potential for ad- verse effects on the environment and possible mitigation measures on both a local and regional scale by first characterizing existing air and water quality, and existing sources of pollution, and then developing hypothetical development scenarios to model potential adverse effects. This paper gives a brief overview of the Study's findings concerning air and water resources.

Jan 1, 1980

By E. G. Cauda

Diesel engines are a major source of underground miners? exposure to nitrogen dioxide. In an effort to reduce the exposure of underground miners to regulated and unregulated diesel emissions, primarily particulate matter, mining companies in the U.S. are retrofitting existing and introducing new engines with various exhaust aftertreatment technologies. Different aftertreatment devices, or changing the operating temperature of a selected device, can have unexpected effects on the concentration of nitrogen dioxide emitted by a diesel-powered piece of equipment. This paper provides an overview of the effects different exhaust aftertreatment technologies available to the mining industry have on no2 emissions.

Jan 1, 2010

"A commercially available through-the-earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multisite evaluation of available TTE systems. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a postevent mine shutdown environment. For this study, surface-to-underground and undergroundto- surface communications were tested. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded mixed results. Future experimentation is planned to further examine the phenomena observed at this mine IntroductionThe ability to establish effective communication between surface and underground personnel after a mine event is essential for both evacuation and rescue efforts. Current wireless underground communication technologies are reliant on intermediary physical infrastructure, such as antennas and repeaters, to enable underground communications. As such, communications are easily disabled during a mine event because of the inherent vulnerabilities to physical damage (Damiano, 2012; National Academy of Engineers, 1970; Yenchek et al., 2011). A true emergency communications system would function regardless of a mine’s physical state. Through-the-earth (TTE) wireless communication technology only requires the use of a single transmitter and a single receiver to achieve point-to-point communication through solid strata. With this capability, TTE systems have the potential to serve as a true emergency communications platform."

Apr 1, 2016

By William F. White

It is a pleasure to have the opportunity of being here today to discuss the application of horizontal filters in the metallurgical industries. The use of horizontal type filters has been limited in metallurgical plants. However, in the recent past there have been new designs of this type equipment which greatly broaden their field of application. Through their use in many applications, important economies can be achieved over more conventional methods. The first of the modern continuous horizontal filters was initially developed by Oliver United Filters as their scroll type horizontal filter. This was an outgrowth of the old Oliver Sand Table that was limited to very coarse, free filtering pulps containing no appreciable amount of fine particles. The sand table was rather limited in application. The later continuous scroll type horizontal filter provided for a reverse air blow after discharge which reslurried the heel remaining and permitted the filtration of pulps containing finer particles. In the manufacture of phosphoric acid by the ?wet? process, the filtration of gypsum from the strong acid presented an extremely difficult filtration problem due to blinding of the filter media caused by crystallization of the soluble salts contained in the acid. A filter which allowed for continuous cloth washing was required, and this led to the development of the continuous pan type, and travelling belt type horizontal filters which provided for this need. Among the filters developed were the Prayon by Engineering and Industrial Corporation of Luxembomg for use in their phosphoric acid plants. They are one of the largest manufacturers of phosphoric acid in Europe. The Dorr-Oliver Traveling Pan Filter was also developed by Mario Giorgini, Manager of Dorr-Oliver?s Italian subsidiary, for use with the Dorr Company?s phosphoric acid process. Basically, there are four existing types of horizontal filters in commercial use at this time: The scroll discharge non-pan type, the continuous belt type (Lurgi), rotary pan type, and the traveling belt type. The construction and principle of operation of these various filters will be discussed.

Jan 1, 1958

By T. Emery, D. Sweet, J. Bourgeois, M. Gomez, B. Seymour, J. Feiler

For traditional underhand cut-and-fill mining operations, it can be challenging to design a suitable cemented paste backfill (CPB) mix that can meet the necessary strength requirements and yet maintain its ductility. In deep underground metal mines, the CPB must achieve a high enough strength to be competent under high stress conditions while also remaining ductile enough to withstand high strain from squeezing ground as underhand mining continues under backfilled stopes. To eliminate ground falls that result in injuries and fatalities, researchers from the Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) have partnered with Aerix Industries, a producer of concrete additives, to study the effects of foaming agents on the strength and ductility of CPB. This laboratory study examines the impact of various amounts of foam additive on the strength and ductility of CPB mix designs, using binder and tailings provided by Hecla Limited from the Lucky Friday Mine

Mar 2, 2022

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare's King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement's returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry's balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972

By Robert O. Vernon

Urban sprawl, and all its attendant problems, is upon us. In Florida, and much of the rest of the world, this has been intensified by a special problem - the coastal zone - a land of high-intensity urbanization localized where the sea and our citizens interact. Florida is blessed by a long coastline of beautiful beaches, indented by estuaries, lagoons and spring fed rivers. Rocky and sand covered islands invite habitation. A large and varied fauna and flora make recreation an avocation and work a pleasure. Accompanying these people are all the sustaining, and satellite industries that find the climate, labor, and commodity markets, cheap water transportation, and natural resources to be attractive. It is estimated that by the year 2008 a megalopolis will stretch down the Atlantic Seaboard from Georgia to encompass the Keys and extend along the Gulf to Alabama. This city will be fenced by the sea on one side and by the water management works, necessary to provide the water supply for this complex, on the other. What can we do about increasing the amount of water available for this population and decreasing the resultant wastes??? Rarely has there been tendered a more favorable opportunity for a coordinated planning and development project that will provide public access to beaches and multiple use of the coastal lands. Florida, as a peninsula swept by ocean breezes, having a largely indigenous water supply and only the beginning of the pollution of estuarine and coastal waters can cope with air, water and coastal dissipation and pollution, if we have a beginning at providing a constant water supply and at limiting pollution. This answer would appear to lie underground, where the porous limestones are interbedded with impervious fine-grained sediments and ground-water that circulates through these aquifers empty to the ocean and Gulf along the continental slopes.

Jan 1, 1969