Search Documents

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

Careful financial analysis of capital investments has always been a vital task in mining which is one of the most capital intensive sectors of the economy. Furthermore, mining costs have leapt ahead at an astonishing rate in recent years not just due to accelerated inflation, which affects everyone, but also due to the imposition of enormous costs of enviromental regulation and the continuing decline in ore tenor. Not only have unit costs risen, but the amount of effort expended to recover a pound of metal has increased due to the inexorable decrease in ore grades. New low-margin, high-volume mining investments place increasing importance on sound financial planning. Owing to the enormous investments involved, a greater share of individual corporate resources is committed to these projects than is normally the case in other industries. Thus, the consequences of failure are extremely grave, and a close examination of all inputs to the evaluation equation is clearly indicated.

Jan 1, 1979

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By C. G. Treworgy

Geologists at the Illinois State Geological Survey are evaluating geologic and land use conditions that affect the minability of coal to determine how much coal is available for development using current technology and mining practices. Coal resources are being evaluated for selected 7.5-minute quadrangle study areas. In a central Illinois study area, more than 25% of the deep-minable resources were limited from development by unstable roof conditions resulting from thick unconsolidated sediments overlying thin bedrock overburden. In some southern and southeastern Illinois study areas, geologic conditions associated with a paleo-channel limit the minability of significant resources of low-to medium-sulfur coal. Some features which were thought to limit mining, such as areas of closely-spaced oil wells, have been found to have minimal impact on the amount of coal recovered.

Jan 1, 1995

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By V. Duddempudi, B. Goertz, J. Brune, G. Bogin, F. S. Barreto

"INTRODUCTION In designing a new pneumatic Dust Sampling Device (DSD) for coal mines, it was essential to analyze the air and particle flow inside the device in detail using Computational Fluid Dynamics (CFD) modeling. Several CFD models were developed to simulate the air and dust flow and sample collecting process of the DSD. These CFD models were developed to assist in the design of the DSD instrument prototypes for laboratory testing. Nozzle and injection parameters such as geometry, air velocity and pressure, were varied across a wide range to obtain the optimal settings to accurately simulate the fluid dynamics of the multi-phase flow within the DSD. Accordingly, these parameters were used as a guide for the design of the DSD and to verify the dust scouring dynamics, which is designed to represent the dust entrainment during an actual methane or coal dust explosion. BACKGROUND The 2010 explosion at the Upper Big Branch mine has demonstrated the destructive violence of a coal dust explosion. A major contributing factor for this disaster was that the mine operators did not have a reliable, direct-reading method to collect mine dust and determine inert content and combustibility. This led to the development of a new prototype handheld, pneumatic mine dust sampling device (DSD), which blows a puff of air and entrains the mine dust by mimicking the entrainment process during a mine explosion. A computational Fluid Dynamics (CFD) model is used to analyze the air and dust flow inside the DSD. The objective of the CFD modeling effort is to find the optimum design of the DSD prototype, nozzle orientation, air pressure and pulse length by analyzing and varying these parameters so that the scouring action collects a valid, representative and repeatable mine dust sample. CFD MODEL DESIGN Figure 1 shows a wireframe image of the DSD which is utilized in the setup of the CFD model. The DSD has a triangular cross section and is 10 cm wide. Two nozzles with cross-sectional dimension of 2.8 cm by 0.25 cm act as inlets at the narrow end of the triangular cross section. The CFD model includes a reference plane 6 cm away from the nozzle to measure the quantity of dust collected. The geometry shown in Figure 1 was created for the model and it matches with the design of the actual device shown in the figure 2. Symmetry, along the plane X-Y through the center of the device, is used to reduce the number of computational cells in the CFD model. Figure 2 shows the prototype device used for experimental testing. CFD MODEL SETUP Figure 3 shows a hexahedral mesh with a cell size of 0.8 mm and the total number of cells is around 650,000. The ANSYS Fluent® pressure based solver with a transient case was used with a total duration of 40 ms. The 40 ms simulation time is based on experimental measurements to capture the injection of air and initial scouring of dust."

Jan 1, 2016

By D. Marino

Over the last 20 years, the manufacturing sector of our country has been called upon to comply with ever core stringent environmental standards. The primary metals sector was particularly hard hit early on, to develop the technology, acquire the equipment, and implement the programs to eliminate or reduce the by-products of metal making. To this end, through a combination of technological innovation and extensive capital expenditures, the metals industry has met, and in many cases, exceeded the minimum standards. It is to this escalating cost - liability exposure issue - that Dereco has addressed itself. As we move into the decade of the 90's, the challenge facing the metals industry concerning the environment will be even more difficult than the previous decade. To focus in on one major aspect of legislated environmental regulations, the issue we will address today is; now that the by-products of metal production have been identified, accounted for and collected, how are they to be disposed of? During the course of this presentation, actual data will be presented from our 4 1/4 year on-site experience at J & L Specialty Products

Jan 1, 1992

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By Jr. Lownie

Estimates of the cost of producing any commodity generally fall into several classes depending upon the motives and needs of the estimator. There are estimates intended to show how low costs might be with favorable conditions if everything goes well. At the other extreme, there are estimates which show how high costs might be if troubles develop. The estimates in this paper for the cost of producing direct reduced iron (DRI) are accompanied by discussion to point out how the final figures may be adjusted in either a promotional or a conservative direction. Because we do not have a specific process and a particular set of conditions in mind when discussing this subject today, this paper deals with the general situation, with considerable attention to how the estimates can be made more specific once one knows the particulars of a given situation.

Jan 1, 1978

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By J. Astier

The idea of using only one strand for both sintering and cooling of the sinter is not new. In 1952, in the U.S.A. a sintering plant was built at Benson Mine (Star Lake, N.Y.), including : - 68 m2 or 735 sqft (8 wind boxes) for sintering, - 22 m2 or 237 sqft (3 wind boxes) for cooling. In the USSR, a large number of machines have been built allowing for cooling of the sinter on the strand, especially the 4 m (about 13 ft) machines, with : 252 m2 sintering grate area 60 m2 cooling grate area 312 m2 total grate area. However, such ventures did not prove very successful, and the IRSID embarked many years ago on a research program to discover : - what are the problems associated with cooling on a sintering strand ; - what are the possible solutions for industrial plants.

Jan 1, 1974

By W. C. Hirt

Selective flocculation was used to produce superclean zinc concentrate with minimized silica contamination. Research was carried out on a flotation concentrate from the Jersey Miniere Zinc Company (JMZ) in Gordonsville, Tennessee. The material was first dispersed with sodium silicate and then causticized tapioca starch was used to selectively flocculate the sphalerite, leaving the silica in suspension. This technique has been applied commercially to iron ore beneficiation but has never been used for processing zinc. The feed material assayed 0.45% Si02. Use of 0.56 kg/tonne (1.13 lb/st) of sodium silicate and 0.070 kg/tonne (0.141 lb/st) of causticized tapioca starch resulted in 98.2% zinc recovery in a purified zinc concentrate assaying 66.0% Zn and 0.24% silica. The present target level for silica contamination in JMZ zinc concentrates is 0.3% Si02. This work has shown that selective flocculation offers a potential method for cleaning flotation concentrates, particularly where low silica products are required.

Jan 1, 1993

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By Edwin R. Phelps

Good morning ladies and gentlemen - today I am in an enviable position for two basic reasons - No. 1, since I am first on the program, the audience should start out awake because those that partied too much last night are still asleep, but in their room, not here. No. 2, since copper, iron, and mining technology are not competitive, the veracity of my statements will not be questioned. Most such meetings I attend are based on the subject of energy and the coal industry does have competition from oil, gas, hydro, and nuclear. However, to counteract this advantage I am the usual engineer with a limited vocabulary by schooling, and the remaining vocabulary almost completely eliminated due to the presence of ladies. In relation to the past of the coal industry, we have not only suffered the competition of other energy sources mentioned before, but in addition have in the last 25 to 30 years been required to meet the demands of a vastly changing market. To explain this statement, I am sure many of you can remember 30 to 40 years back when most homes were heated by coal furnaces or stoves and shudder to recall the shoveling of coal into the fire and the carrying out of ashes with the attendent manual labor dust. Now this space heating portion of our sales has almost become non-existant due to an almost universal switch from coal to natural gas, oil, and electric heating. Actual figures show a decrease from 119 million to less than 28 million tons per year in less than a twenty year span. Also, most of you can remember the coal burning steam locomotives and the tremendous volume of coal they consumed and then the very rapid change to the diesel-electric locomotives, incorporating improved large diesel engines driving D C generators and electric drive motors, which resulted in cheaper motive power. This change over was so complete that the annual tonnage of coal dropped from 125 million to less than 2 million tons in 15 years. 'Actually, now it requires some considerable interrogation and traveling to find a locomotive still operating on steam.

Jan 1, 1968

By R. S. Datta

Regulations on sulfur emissions have caused the electric utilities to evaluate various methods of meeting them. Low-sulfur, low-volatile coals can be burned alone or blended with high-volatile? coals. This option may be a cost-effective alternative to the installation of scrubbers on coal-fired combustion systems. In some blending applications, problems may be encountered because the low sulfur content and high calorific value of the low-volatile or other clean coal allow it to economically upgrade extremely poor quality coal. While this is done to meet specification purposes, actual boiler performance may be dominated by the poorer quality coal. Thus, the reputation of the low-volatile or other clean coal suffers. As a result of laboratory and full scale testing, conducted over the last five years, a model has been developed to evaluate the relative combustion characteristics of various coals and coal blends. A database for different coals has been gathered. This paper presents the model and shows how power plants and coal mine personnel can use it to evaluate their coals from different sources. It can be used to blend two or more coals from different sources so that thee blended coal has flame stability characteristics which are similar to those of the baseline coal.

Jan 1, 1991

By J. Wiedenroth

Since the end of the 1970s Pipe Conveyors have become increasingly important for conveying bulk materials because they have some specific advantages over conventional troughed belt conveyors. FLSmidth KOCH Pipe Conveyor represent the marked-leading know how of the former KOCH Transporttechnik GmbH, which belongs to the FLSmidth Group since January 2007. Pipe Conveyors from FLSmidth KOCH are already being used successfully at more than 260 locations around the world. Their special properties, their extreme flexibility, the horizontal and vertical changes in direction without transfer points, the small space requirement, the low-noise running and their optimum protection of environment and material without any additional casing mean that Pipe Conveyors can provide transport solutions that are often far superior to other conveying systems. The utilization of these many advantages will be illustrated in the following example of the world?s longest Pipe Conveyor at Cementos Lima, the Peruvian cement producer.

Jan 1, 2010