Search Documents

By M. Wickham

Design of an open pit backfill requires an understanding of highly varied processes including slope stability, hydrogeology, pit lake chemistry, climate, runoff, and mine waste behavior. Dynamic systems modeling (DSM) provides flexibility to the designers of open pit backfill, allowing them to directly integrate many different physical processes and varying levels of complexity. DSM also provides for the efficient application of uncertainty analysis to define a range of possible results, the sensitivity of the results to uncertainties in model inputs, and the value of additional data. This paper presents the results of an analysis using DSM to evaluate a pit backfill design at an Arizona mine. The objective of the partial backfill was to stabilize an active slope that threatened facilities adjacent to the pit. DSM was used, in part, to develop a pit lake water balance model for evaluating the influence of the backfill on the ability of the pit to maintain passive hydraulic containment of groundwater and surface water inflows and for evaluating costs for various backfill scenarios.

Jan 1, 2001

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014

By T. Tafi

The Ute-Ulay project area is located approximately five miles west of Lake City, in Hinsdale County, Colorado. The Ute-Ulay Mine site is approximately one mile east of the project area. The elevation of the site is 9,200 feet and is adjacent to Henson Creek (Figure 1) [ ] The Ute-Ulay Mining complex is an inactive gold, silver, and zinc mining/milling operation, that operated from the 1880?s until the 1970?s, and sporadically into the late 1990?s. The mining complex comprises several levels of underground mines, a flotation mill, and an abandoned town site. Due to the narrow, steep sided canyon, milled tailings were pumped upstream one mile in a sluice box to a wider section of the canyon, and deposited into five tailings impoundments and one berm located between the impoundments. An estimated 9,000 cubic yards (yd3) of fine grained tailings were located in the impoundments adjacent to the creek. The Ute-Ulay project area consisted of the mill tailings impoundments located upstream from the historic mine.

Jan 1, 2011

By Andrew Howard

As the mining industry moves further into developing countries in search of new resources, its role in international development is coming under increasing scrutiny. This is a trend that is likely to accelerate, along with the potential for headaches among managers in the industry. Public interest in development and environmental issues is rising as faith in “big business” falls. This has strengthened nongovernmental organizations (NGOs) campaigning for sustainable development. And it has put more pressure on banks, governments and development agencies to curb corporate misdemeanors. Developing world governments are also becoming emboldened to reject previously agreed terms they do not consider equitable. The mining industry has begun to formulate a response to these pressures but must go much further. Societal and environmental issues must move from public relations to core strategic thinking. Abiding by rules or codes is not a relevant response. Instead, genuine support for sustainable development is required. This will involve delegating the responsibility for engaging with local communities to on-the-ground staff and developing a dialogue with local stakeholders rather than conducting an initial assessment and disengaging.

Jan 1, 2006

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By Robert S. Shank

Introduction The Pinto Valley open-pit copper mine is located in southern Arizona, 11 km (7 miles) west of Miami. Production at Pinto Valley began in 1974. About 350 Mt (386 million st) of ore and waste was removed by the end of June 1982. At that time, the mine was using more than 90 major equipment items with a total mobile fleet numbering 320. Some of the major equipment consisted of four Marion M4 rotary drills; six P&H 15, 11.5- and 19.1-m3 (15- and 25-cu yd) shovels; and 24,136- and 154-t (150¬and 170-st) Wabco haulage trucks. This equipment was used to move more than 139 kt/d (154,000 stpd) of ore and waste. The mill was processing more than 50 kt/d (55,000 stpd) of mine ore. Shutdown A two-week vacation shutdown began in July 1982. Maintenance jobs were scheduled, and most employees left for the vacation. During the vacation period, copper prices fell below $1.32/kg ($0.60 per lb). Inventories remained at alarmingly high levels. At this point the mine was losing more money operating than it would by being shut down. The vacation shutdown was first extended to five weeks. But, after further evaluation, the mine was shut down indefinitely. In Dec. 1982, Cities Services Co., owner of Miami Operations (which included the Pinto Valley mine and mill), was acquired by the Occidental Petroleum Corp. On March 1, 1983, Occidental sold the operations to Newmont Mining Corp., and Newmont created Pinto Valley Copper Corp., as a wholly owned subsidiary. Copper continued to be produced by the Pinto Valley solvent extraction-electrowinning (SX- EW) plant because of its low cost per pound of production. To ensure proper equipment care during the shutdown, maintenance management was given three goals; • maintain the SX-EW plant; • maintain the environmental and pollution control systems such as domestic water pumps and mine dewatering; and

Jan 4, 1985

By William R. Yernberg

The 26th Peruvian Mining Convention (Convención de Ingeneieros de Minas del Perú) was held Sept. 15 through 19, 2003, in Arequipa. The convention was sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru). The Institute has been organizing these events since 1954. They are now held every other year. The conventions spotlight Peru’s mineral resources and have contributed to the tremendous growth of the Peruvian mining industry. This year’s meeting consisted of technical sessions, forums, field trips and social activities. It was held at the Tecsup Institute of Technology of Arequipa. More than 3,000 mining professionals attended. As always, the meeting was well organized, and participants expressed gratitude to the organizing committee for another successful meeting.

Jan 1, 2004

By C. E. T. White

Although trace amounts of Indium are found in many ores, commercial production of the metal has come almost exclusively from residues, flue dusts and slags generated by Zinc recovery operations. Our paper attempts to summarize the various approaches used to recover Indium from these by-products. Some comments on production and price trends are included as well as our views on future availability.

Jan 1, 1982

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill?s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.

Jan 1, 2009

By J. Egan

The recovery of gold by ore leaching is influenced by the size of the particles and the chemical environment. Within the experimental error associated to the testing of gold ore, results of a series of leaching tests conducted with natural ores rather than monosized samples confirm that gold dissolution increases with decreasing ore particle size. The tests also indicate that the dissolution of gold in the ore within a size interval is weakly affected by the intensity of the size reduction method.

Feb 27, 2013

By Bradshaw, Y. S. Cho

The size of bubbles plays an important role in flotation. Equations used to calculate the size of bubbles all show the effect of liquid/gas surface tension. However, the surface tension does not change much with frother concentration and experiments conducted using single capillaries (or single-hole spargers) do not reveal any clear effect of the frother concentration on bubble size. The size of bubbles does, however, strongly depend on frother concentration when multi-hole spargers are utilized (or when measured in a flotation cell); at low frother concentrations the bubble size is much larger indicating coalescence as a main mechanism determining the size. Coalescence can be prevented at frother concentrations exceeding the critical coalescence concentration (CCC), which in turn was found to be interrelated with the dynamic foamibility index (DFI).

Jan 1, 2001

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

By Z. H. Zhou

It is difficult to remove cadmium from raw indium using only electrolytic refining because their standard potentials are similar. In this paper, physical and chemical methods were used to remove Cd from raw indium. Indium metal is vacuum refined for two hours at 400°C with a vacuum pressure of 20 Pa. In this process, 99.70% of the Cd can be removed. The removal rate of Cd reaches 90% to 95% when indium is further smelted for 10 minutes in a 20% glycerin solution of KI and I2 at 180°C. When pre-indium is electrolytic refined in an In2(SO4)3-H2SO4 system, in which the indium content is 80 to 100 g/L, the pH is 2.0-3.0 and the current density is 80 to 100 A/m2, the contents of the impurities decrease and the purity of the indium product reaches 99.99%.

Jan 1, 2007

By Len Harris

Webster?s Dictionary describes culture as: ? The totality of socially transmitted behavior patterns, arts, beliefs, institutions and all other products of human work and thought typical of a population or community at a given time. ? A style of social and artistic expression peculiar to a class or society. ? Intellectual and artistic activity. ? The art of developing the social, moral and intellectual facilities through education. The authors have nearly 100 years of combined experience in the mining industry working with and consulting to mining companies and companies engaged in the supply of goods and services to the mining industry worldwide. In this report, they present their experiences and ideas on the importance of cultural aspects in the successful development and implementation of mining ventures. Their suggestions on how to handle culture shock will be of interest to expatriate managers, operators, social workers, and engineering and construction personnel posted to overseas operations, as well as to nationals posted to other parts of their own country.

Jan 1, 2008