Search Documents

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By M. Soya, M. Imazu, Ö. Aydan

"SUMMARY Taru-Toge tunnel is being constructed using drilling-blasting technique as a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan. The maximum overburden is about 400 m. The authors have been carrying out a monitoring program to measure dynamic and multi-parameter responses of tunnel during and soon after the blasting operations using a multi-parameter monitoring system (Acoustic Emissions (AE), Electric Potential (EP), Temperature (T), Humidity (H) and Air Pressure (P)) and stand-alone type compact accelerometers developed by the first author. The measured response involves dynamic vibrations and other measurable parameters caused by blasting as well as by stress-redistribution around the tunnel face. This is one of the first attempts in the world to measure the response of rock mass caused by blasting at a very close vicinity of the tunnel face. In this paper, the authors present the outcomes of this unique monitoring study on the dynamic responses of the Taru-Toge tunnel during excavation and discuss their implications in actual applications. INTRODUCTION The real time monitoring of the stability of tunnels are of great importance when tunnels are prone to failure during excavation such as rockbursting or squeezing (i.e. Aydan et al. 1993, 2001). Experimental studies by the authors showed that rock indicates distinct variations of multi-parameters during deformation and fracturing processes (i.e. Mizutani et al. 1976; Aydan and Daido 2002; Aydan et al. 2003, 2011). These may be used for the real-time assessment of the stability of rock structures. An application of this approach was done to the Taru-toge tunnel a part of expressway project connecting Shin-Tomei Expressway and Chuo Expressway at the boundary of Shizuoka and Yamanashi Prefectures in the Central Japan (Imazu et al. 2015). The parameters measured involve electric potential variations, acoustic emissions, rock temperature, temperature and humidity of the tunnel in addition to the measurements of convergence and loads on support members during the face advance."

Jan 1, 2016

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By C. Ernst

The underground operation at Barrick?s Cortez Mine, located near Elko, NV, required the construction of a 12 foot diameter smooth-lined ventilation shaft. Barrick preferred to mechanically excavate from the ground surface without putting people in the excavation and considered blind drilling by Frontier-Kemper Constructors the best option. Design and construction challenges arose throughout both the excavation and lining stages. A large portion of the rock to be drilled was highly fractured. Important risks that were addressed included water loss into the formation, zones of squeezing ground, damage to drilling tools caused by blocky ground and fallout, and potential hazards during cast-in-place concrete lining. Detailed explanations of these challenges and the methods used to overcome them will be described.

Feb 23, 2014

By S. Philipp

This paper describes several variants of placement and design, from a technical and economic point of view, of shafts, ore bunkers and drifts near shafts of a Russian potash mine. Advantages and disadvantages of the position of different workings are shown as well as an analysis of stratigraphic and geological layers and their use for excavating pit bottoms, haulage drifts and bunker installations. The potash mine consists of two hoisting shafts and one service shaft. The hoisting capacity of one of these skip shafts is planned to be approx. 7 Million tons of crude potash salt per year. Both shafts together will have a hoisting volume of about 14 Million tons. When the mine will increase their highest level of production, it will be one of the biggest potash mines in the world. The skips, the hoist drives and the bunker near the shaft will belong to the largest ones worldwide, too. This paper specifies the features of such a double skip shaft pit in detail and demonstrates problems, which depend on the fact that the pit bottom is in a depth of nearly 1200 m.

Feb 23, 2014

By Ralf Winterberg, Axel G. Nitschke

"Macro synthetic fiber reinforced concrete or shotcrete is seen by many design engineers as offering a viable alternative to steel reinforcement in tunnel linings. The technology is now commonplace for primary and permanent ground support in both mining and civil tunnel applications. It has for instance become the standard form of reinforcement in the Australian mining industry, and has been used for a majority of permanent tunnel linings in recent tunnel construction in Norway. Similarly, macro synthetic fibers are becoming a standard solution for the initial lining in the USA.The use of macro synthetic fiber offers innovative solutions, yielding robust and sustainable tunnel lining designs. Citing recent research and actual projects, this paper presents state-of-the-art design considerations for fiber reinforced tunnel linings relating to structural and long-term performance. Topics include seismic resistance, crack width control, corrosion and durability, as well as sustainment of performance with age.INTRODUCTIONMacro synthetic fiber reinforced concrete (MSFRC) and shotcrete (MSFRS) has reached maturity as an engineered material and is widely used in all forms of tunnel linings, for temporary as well as permanent ground support in both, mining and civil tunnel applications. In the Australian underground mining industry, it became the standard form of reinforcement, where 2014 literally marked the end of steel fiber use in shotcrete [1], and has been used for over 80 percent of permanent tunnel linings in recent tunnel construction in Norway. Similarly, macro synthetic fibers are becoming a standard solution for tunnel initial linings in the USA. Recent examples in civil tunneling are the Devil’s Slide Tunnel and Caldecott Fourth Bore Tunnel in California or the Anacostia River Tunnel Intershaft Connector Tunnel in Washington D.C. In addition, an increasing number of tunnels are adopting shotcrete permanent linings using macro synthetic fibers. Examples include the A3 Hindhead tunnel near Guildford in the UK and the North Strathfield Rail Underpass in Sydney, Australia [2, 3]."

Jan 1, 2016

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By Richard M. Winar

In September of 1988, the United States Environmental Protection Agency (US EPA) published final regulations that effect owners and operators of underground storage tanks (USTs). These regulation include stringent technical requirements for owners and operators of USTs containing petroleum and certain hazardous substances. The technical requirements effect both new (those installed after December 1988) and existing USTs and include notification; performance and operating standards; release detection, reporting, investigation; release response and corrective action; and closure requirements for out-of-service USTs. The USEPA also published final regulations regarding financial responsibility requirements for owners or operators of petroleum USTs in October of 1988. These regulations require owners or operators of petroleum USTs to demonstrate financial responsibility for the costs of corrective action and compensating third parties for bodily injury or property damage caused by releases from petroleum USTs. Like thousands of other industries, the mining industry must become thoroughly familiar with these new regulations in order to properly manage their UST systems, ensure compliance, and understand other ramifications imposed by these regulations.

Jan 1, 1990

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By J. V. Belke

There are many aspects of a grinding mill supply and installation that can result in the mill not operating as intended, resulting in unplanned shutdowns, poor reliability and headaches for all concerned. One of the largest aspects, both in criticality and physical mass, is the mill foundation; if not properly specified, designed and constructed the mill operation will be compromised. The mill foundation starts with the design specification and loading diagram supplied by the mill builder. The importance of understanding these documents and how to apply them is critical for the start of any mill project. When designing mills with a GMD the foundation must be properly modeled to ensure that all interactions of the mill and motor structures, foundation and subsurface strata behave in the intended fashion. All of the previous efforts can be laid to waste if the construction of the mill foundation is poorly handled. Mill foundations are typically the most massive concrete structure at a processing plant and can easily cause nightmares for inexperienced contactors. This paper explores some of the more important facets along the lifecycle of the grinding mill foundation.

Feb 23, 2014

By B. A. Ashley

In 2007, Rosebud Mining Company (RMC) opted to extend the reserve base of Tracy Lynne Mine by developing through a sandstone channel. The extension provided access to approximately 6 million additional recoverable tons (approximately 8 years of mining) which originally had been deemed inaccessible. An evaluation of the mine?s existing ventilation system, which was designed to meet the needs of the original limited reserve, concluded that two ventilation shafts would likely be required to adequately ventilate the projected workings in the expanded reserve. To assist in the evaluation, a ventilation model of the mine was developed using Ohio Automation?s ?ICAMPS MineVent? software based on field data from Tracy Lynne Mine, prior ventilation survey experience at similar RMC mines, and relevant published sources. Model results suggested that the most economical shafts would be an 8-ft diameter return and a 4-ft diameter intake. Unfortunately, issues related to property leasing and shaft site permitting caused construction delays. Therefore, the model was also used and proved to be effective in prioritizing interim ventilation upgrades which could be implemented in order to maintain coal production. Model results indicated that the best interim upgrades included rehabilitating restricted entries and damaged stoppings and replacing the main fan with a higher pressure fan. From late 2010 to mid-2012, all interim upgrades and shafts were implemented. Current models and mine experience indicate that ventilation will not be the limiting factor for mining the additional reserve.

Feb 23, 2014

By B. Stewart

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods, and better hang up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste rock loads on chutes, walls, gates, and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mock-up of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com-pared. Loads on an active ore pass chute were measured.

Jan 1, 1998

By S. M. Robinson

Wollastonite is recognized as one of the most unique, non-metallic minerals in the world. Its history for use in industrial applications is recent compared to other minerals, however, its distinctive physical properties, such as acicular particle shape, and alkaline pH creates incorporation possibilities ranging from bowling balls to automotive fascia, from ceramic tiles to automotive brakes, and from thermal insulation board to industrial and trade sale coatings. Its future use will be impacted by the exploitation of deposits which will ensure maintenance of the acicularity and purity of this naturally occurring mineral. Additionally, closely held surface treatment technology will open up additional niches requiring highly engineered performance.

Jan 1, 1995